Msi k8n neo plat nforce3 250gb : blue screen

hi
just built a amd 64 3400 with msi k8n neo plat: with xfx 256 geforce nvidia graphic n kinston 512 ddr 400.
but for some reason its giving the blue scree with dumping memory msg on the screen.changes the memory but still got the same problem updated the bios to 1.5 still same thing.
any cue with the problem.
thnks

System restore? You need to find out what's causing the problem and you have too many things connected to it to be able to figure out what it is, always start with a basic system - video, primary hard disk, cd + fdd, no more and nothing else connected. Then when something goes wrong along the way you'll have more chance of narrowing it down if the problem appears.
What you'll want to do now is disable/uninstall/unplug any additional non-system-critical components that you have connected to it such as extra usb slots, printers, scanners and anything else. Keyboard, mouse, video with no sound and see if the problem persists. If it does, try another video driver. If it's fixed then reconnect/enable one device and try again until the problem reappears and you can find out what's causing it -- unless you can speed read that message quickly before it shuts down
Now that I think of it, have you set the OS to not automatically reboot on any errors? That might keep the BSOD up there so you can note it down and hopefully point at the problem instead of going through all the above hassle ^^

Similar Messages

  • MSI K8N Neo Platinum Nforce3 250GB - PSU?

    My sister in law have this board, MSI K8N Neo Platinum nforce3 250gb chipset, recently the power supply sounds noisy and a high frequency sound from the Antec Truepower 380W SP. Had maked an RMA to Antec and they had agreed to replace the 380W psu with SmartPower2.0 450W. But they asked me one question, that im not sure about:
    "Make sure that your motherboard does not need the -5V. If you want more information on the power supply you can look at this link: http://www.antec.com/us/productDetails.php?ProdID=26450 "
    So, do Antecs SmartPower 2.0 450W suits this board and what really is -5V for? As I read the manual, it said ATX 20 pin power connector: JWR1 and at pin 18: -5V
    So does it mean this board need a psu that gives -5V on ATX 20 pin power connector and thos board can't use with Antecs SP 2.0 450W?

    Quote from: syar2003 on 22-February-06, 05:10:37
    Hi!
    The K8N Neo Platinum (MS-7030) doesn't use -5v to anything.
    So the -5v from the old atx spesification is not needed in your case.
    WoW, thanks for fast reply!
    So, it won't be any problem to use Antecs SmartPower 2.0 450W with this board then? Want to make sure about it, before accept Antecs offer for replacement and had spent over 4 days to find the problem with his computer. Really don't want to do it again. 
    This is his riggs:
    Antec Sonata
    AMD 64 3000+ S754
    Corsair Value S. PC3200 DDR 512MB
    Maxtor Diamondmax 9 250GB SATA
    Maxtor Diamondmax 9 IDE 160GB
    Sapphire Radeon 9550 Atlantis 128MB DDR
    and
    Accton ethernet card on PCI slot
    MSI D-Bracket2
    so
    With the "new" Antec SmartPower 2.0 450W
    Any problem with this rigg and PSU?
    edit:
    Dound this post that it said the board do need -5V and now Im confused? 
    http://www.archivaty.net/forums/about12964-30.html

  • SATA port multiplier on MSI K8N Neo Platinum - NForce3 250Gb?

    Hi,
    I have a MSI K8N Neo Platinum, which uses a NForce3 250Gb chipset. I have read that port multipliers can use either SATA or SATA II hosts and drives, but I don't know if the technology is 100%, transparently compatible.
    Is the aforementioned chipset/motherboard compatible with port multiplier technology?
    Does it support FIS, which gives the greatest perfomance?
    Does it need a BIOS or driver update?
    Thanks for the attention
    Brazilian Joe

    Quote from: syar2003 on 22-February-06, 05:10:37
    Hi!
    The K8N Neo Platinum (MS-7030) doesn't use -5v to anything.
    So the -5v from the old atx spesification is not needed in your case.
    WoW, thanks for fast reply!
    So, it won't be any problem to use Antecs SmartPower 2.0 450W with this board then? Want to make sure about it, before accept Antecs offer for replacement and had spent over 4 days to find the problem with his computer. Really don't want to do it again. 
    This is his riggs:
    Antec Sonata
    AMD 64 3000+ S754
    Corsair Value S. PC3200 DDR 512MB
    Maxtor Diamondmax 9 250GB SATA
    Maxtor Diamondmax 9 IDE 160GB
    Sapphire Radeon 9550 Atlantis 128MB DDR
    and
    Accton ethernet card on PCI slot
    MSI D-Bracket2
    so
    With the "new" Antec SmartPower 2.0 450W
    Any problem with this rigg and PSU?
    edit:
    Dound this post that it said the board do need -5V and now Im confused? 
    http://www.archivaty.net/forums/about12964-30.html

  • MSI K8N-NEO-PLATINUM nForce3 250 + Corsair vs.

    Hi, I'm thinking of buying a new computer with a MSI motherboard and now thinking if these will correct and have no direct problems, MSI K8N-NEO-PLATINUM nForce3 250GB + Corsair VS512MB400 Value Select 512Mb DDR PC3200 400MHz 184pin Unbuffered CL2.5. I'm not the guy who is intresserd in overclocking and such things.
    Will that motherboard and memory correct good with each other ?
    Sorry for my bad english. :D
    //Johan
    EDIT: I think I made this topic in the wrong forum. Mods move it to AMD64 nVidia Based board  ?

    MakubeX,
    I have the Antec True Power 480. Unfortunately it only has 22 or 23 amps (the specs and the label on the psu have different ratings  ) on the +12V rail. Most of the folks here recommend a power supply with at least 24 amps.
    The good news is that the system in my sig is working flawlessly so the extra 1 or 2 amps don't seem to make a big difference, at least in my case. I will say, however, that according to Core Center my +12V rail runs around 11.5 volts, which is low and nearly out of ATX sepc. The low voltage will result in higher amperage draw...but again, the system is stable.
    I wish you good luck

  • Msi k8n neo plat : blue screen

    hi
    just built a amd 64 3400 with msi k8n neo plat: with xfx 256 geforce nvidia graphic n kinston 512 ddr 400.
    but for some reason its giving the blue scree with dumping memory msg on the screen.changes the memory but still got the same problem updated the bios to 1.5 still same thing.
    any cue with the problem.
    thnks

    Duplicate Thread
    https://forum-en.msi.com/index.php?threadid=72851

  • MSI k8N Neo Plat 2...system freeze and crash during h-end gaming...

    MSI k8N Neo Plat 2
    AMD athlon 64 3800+
    Centon 512 MB DDR 3200 x 4
    nvidia geforce fx 5700
    win xp pro
    Creative Audigy 2
    Under some graphically intensive situations, during gaming,  especially dealing with alot of background visuals, like fire/lava, etc, the system will after a short while of playing either, crash, freeze, reboot, or freeze while a loud screeching nosie emits from my speakers...I have tried updating my graphx card drivers to the most recent and the symptons still persist..Is there something I need to set in BIOS regarding mem timings, I have tried playing around some, but that hasnt worked either...Any help would be greatly appreciated !!!
    ,

    Try raising RAM voltage to 2.7v - 2.8v.
    If no go - Run Memtest86 http://www.memtest.org/#downiso
    If no go -  Try onboard Audio ( disable / remove Audigy2 )

  • Msi k8n neo plat problems

    I have built 2 computers exactly the same.
    msi k8n neo plat
    512 corsair xms ddr 3200
    8og sata maxtor
    amd 64 3200
    128mb ati 9800 pro
    asus cd drive
    When i tried to install windows xp pro on both the machines i got the same error. could not copy file. On each try the file was a different one. After hours of trying new things i found that putting the memory in slot 2 on the motherboard  solved the problem, windows installed and booted up as norm. When i moved the memory back to slot 1 the computer would not boot.
    I have now left the memory in slot 2 but the computer will still crash every hour.
    I am sure this is something to do with the memory but not sure what the problem is.
    Can anyone help.

    Can anybody tell me what i should set the cpu fsb frequency to in the bios.
    I just read this in the faq
    What is the fsb speed of this cpu?
    Depending on which FSB you are asking about: The Athlon 64's have the memory controller built in (which was previously part of the Northbridge on the motherboard) which uses up to 200MHz DDR Memory (400MHz FSB) The HyperTransport link from the CPU to the rest of the motherboard runs up to 800MHz. Just to expand on my answer... The HT link is 800MHz, but it's 16 bit in size (2 bytes worth of data per clock) the total bandwidth of the HyperTransport link is 3.2GB in total - 1.6GB sending data to CPU and 1.6GB receiving data from CPU.

  • MSI K8N NEO PLAT + CD / DVD-RW Drives

    Hi, i have the msi k8n neo plat. I recently had to replace my old mobo due to the old power supply blowing or something. So i got me a 480watt enermax coolergiant psu. Replaced the mobo for a new msi k8n neo plat. Put the mobo in and psu. Working fine and dandy. Now i installed 64bit xp to primary, and ive had it running for for about 2 weeks. Went to install linux to the second hard drive, so i changed the boot order, saved settings and went to load disc...however now my cd and dvd drives dont work, and they dont work in windows either.

    Can anybody tell me what i should set the cpu fsb frequency to in the bios.
    I just read this in the faq
    What is the fsb speed of this cpu?
    Depending on which FSB you are asking about: The Athlon 64's have the memory controller built in (which was previously part of the Northbridge on the motherboard) which uses up to 200MHz DDR Memory (400MHz FSB) The HyperTransport link from the CPU to the rest of the motherboard runs up to 800MHz. Just to expand on my answer... The HT link is 800MHz, but it's 16 bit in size (2 bytes worth of data per clock) the total bandwidth of the HyperTransport link is 3.2GB in total - 1.6GB sending data to CPU and 1.6GB receiving data from CPU.

  • Msi k8n neo plat and audio problem

    got me a msi k8n neo plat, great board but have a few minor problems that i have noticed. one is the audio problem i have- when i listen to winamp, and surf, i will loose my winamp connection surfing, and then have to start winamp. is this a bios thing, or nvidia platform or chipset problem?

    Hi
    Thats the Nvidea board, this is the via board forum. You want forum below this one, as they will be able to help better.
    good luck
    jocko

  • Msi k8n neo plat and microsoft ie

    getting my msi k8n neo plat board running satisfactory , except for one problem . when i got to amdmb.com, i start surfing the site, and after a minute or 2, i get a microsoft ie error, send the error report to microsoft, and then ie closes. what is the problem , is it with amdmb.com site? its the only site that this problem with ie is present, all other sites i don,t have this problem

    just tryed using the browser firefox, and it works great.  its just ie that doesn,t work on amd.mb, and only that site. wierd problem, never experienced anything like it before. had run a short memtest , no errors.  the 6800gt , msi k8n neo plat and amd 64 3400 work great. get some super madonion benchmarks-all default-1024 x 768 32bit- 22,755. i was hoping for 22,000, but exceeded my expectations. can get into the 23,000 + with overclocking the 6800gt, have had it overclocked at gpu-412, memory 1.12. not sure how much more you can increase the numbers, thinking my gpu is close to the limit at 412.had a problem with windvd, it ended up being a configuration in windvd- had to enable hardware acceleration , bingo- worked great after that. got my corsair xms pc 3200 to work at 6-3-3-2 timings. still getting to know the board,  there is definately a learning curve to be delt with on this board, but i am getting it to work better by the day.

  • Msi k8n neo plat and 3dmark03

    with my msi k8n neo plat , bfg 6800gt, and amd 64 3400 clawhammer- i get 11,114 in 3dmark03. seems like i should be getting a higher score-any suggestions.

    You appear to have misread my post, read carefully, I said "at clock speeds" not "at stock speeds" which I think is where u misunderstood. I know it's overclocked, but who isn't going to if there is so much headroom? With coolbits you can have higher speeds when running 2d or 3d applications to keep temps low and for longevity of the card.

  • Overclocking msi k8n neo plat

    trying to overclock my msi k8n neo plat and run mad 2001
    hardware - amd 64 3400
    bfg 6800gt
    corsair pc3200
    i go into bios and set ram at 400mhz, set agp at 67 mhz. then open center and enter 210 mhz fsb. when i start madonion, it freezes. is it my memory?

    Could be a ram incompatibility issue.  I have some OCZ pc3500 EL which is great in my other systems, but doesn't work in the Neo without bluescreens and crashes to desktop.  It might also be a power related issue.  What type of power supply are you using and what is the amperage on the 12v rail?  That seems to be pretty important for this board.

  • MSI K8N Neo Plat edit. and IDE

    Can anybody tell me how many IDE units you can run on this motherboard? I do not want to use raid 0 or 1.  I have a KT3 ultra - aru at them moment with 6 single IDE units, but now I need to upgrade.
    Thanks for any help.

    Hi,
    you can connect 4 IDE devices and 4 four sata devices on MSI K8N Neo Plat editition.
    If it's not enought you can plug an IDE PCI card....

  • MSI K8N Neo Plat help please!!!

    Hi guys, long time browser first time poster on these forums.
    I have a few questions which im hoping some of you can help me with, i searched through the message boards but found no answer so I thought i'd write a plea for help.
    I recently sold my Asus K8V Deluxe and decided to replace it with a nForce3 250Gb alternative. I ended up purchasing an MSI K8N Neo, which is fantastic apart from 3 particular issues:
    1. After the PC POSTs and before the WinXP loading screen, there is a long delay (about 25-30 seconds) where the PC does nothing. No hard disk activity or anything, just sits there on a blank screen. Can anyone help with as to what might be causing this problem?
    2. Im using a WD 120Gb SATA hard drive, connected to SATA port 3. Using the 'speed test' tool that is provided under the Nvidia Serial ATA controller, I receive a burst speed rate of 69.9mb / sec and a sustained speed of 52.4mb / sec. This falls far below the claimed 150mb / sec. Is there anything I can do to improve this??
    3. In terms of actual system performance its more or less identical to when I had the K8V. I've read in a few reviews that the nForce3 mobo's are faster than the VIA variety. Again is there something I can do to improve this or am I just a gullible mofo?
    All drivers are completely up to date and the system is running on a fresh install of XP.
    Cheers.

    Quote
    1. After the PC POSTs and before the WinXP loading screen, there is a long delay (about 25-30 seconds) where the PC does nothing. No hard disk activity or anything, just sits there on a blank screen. Can anyone help with as to what might be causing this problem?
    First, are you raiding drives? It seems you are not, so my next question is did you load the drivers off the floppy disk? For sata drives that are not raided, this is an unnecessary step that has caused systems to hang at startup.-solution- reformat without loading these drivers.
    Quote
    2. Im using a WD 120Gb SATA hard drive, connected to SATA port 3. Using the 'speed test' tool that is provided under the Nvidia Serial ATA controller, I receive a burst speed rate of 69.9mb / sec and a sustained speed of 52.4mb / sec. This falls far below the claimed 150mb / sec. Is there anything I can do to improve this??
    That is about right for that drive. The 150 mb/s is just theoretical, not realistic at this point. My raptor at 10,000rpm's gets about 121mb/s burst and 70mb/s average. So if anything your burst may be a little low. The rpm's of the hard drive is makingmore of the difference than the sata.
    Quote
    3. In terms of actual system performance its more or less identical to when I had the K8V. I've read in a few reviews that the nForce3 mobo's are faster than the VIA variety. Again is there something I can do to improve this or am I just a gullible mofo?
    The Nforce3 250's are generally a little faster than via's but in some areas not so. These difference would hardly be noticed by the naked eye in most instances, only benchmarks. So you sre not gullible, just a little uninformed about the actual speed difference.

  • K8N Neo Platinum (NForce3 250GB) and SATA2?

    Hi!
    I have MSI K8N Neo Platinum with chipset NForce3 250GB. It has SATA Controller. Can someone tell me (with certainty), if I can install a SATA 2 drive? (Once I contacted Maxtor, they told me that I would rather not install a SATA2 drive in a NForce3 250GB based mobo) Has anyone had a problem with a SATA2 drive in this mobo?
    my pc is:
    AMD 64 3000+
    MSI K8N Neo Platinum
    2*512MB Kingston DDR400
    200GB SATA SEAGATE
    320GB SATA WD
    Thanks in advance! 

    Figures , as Maxtor is the vendor that has problems with their sataII DiamondMax drives on nforce3/4 buildt in sata controllers.
    However , Hitachi T7K250 250GB SATA2 is one that works flawlessly on nforce3 .
    They are also set to sataI from manufacturer .
    See how to use hitachi feature tool to change drive options :
    http://www.pcbuyersguide.co.za/showthread.php?t=4005

Maybe you are looking for

  • CUPC – Unable to go into deskphone control mode and unable to chat

    Home Lab – learning Presence CUCM 9 CUPS 9 (not 8.6 as virtually all of the help and discussion forums, documents, etc are for) CUPC 8.6 (3 copies running on 3 different laptops) 4 users configured in CUCM for Presence capabilities No LDAP integratio

  • How to move from vmware ESXi 5.5 to Hyper-V 2012 R2 on same hardware?

    I have Vmware ESXi 5.5 Update 1 with two disks, called RAID0 (3.6 TB) and RAID5 (10.9 TB). I am tired of having to rebuild ESXi every sixty days for home use so I am planning on moving to Hyper-V, but I'm a little nervous. I don't have swing kit, so

  • Blank Line in a query

    How to add a blank line in a query and it does not have to zeros... thanks

  • Validation on datepicker

    Hello expert i want to create validation on datepicker when we select the date.is it possible ? please help me for that Thanks & Regards Vilas maskey

  • Oracle 11g R2 RAC installation on AIX

    hi, I wana setup Oracle 11g R2 RAC on Ibm with AIX. Is there any good document or cookbook explaining step by step procedure for the installation...I'll be thankful thanx