MSI K8N Neo4 not recognizing USB 2.0

All my USB ports are recognized as being USB 1.1. Here's the kicker, in Device Manager, there are two USB Controller nodes. One has a Standard OpenHCD USB Host controller (USB 1.1) and the other node has a PCI Class USB 2.0 Enhanced Host Controller. However, all my devices are being run off the USB 1.1 controller. If I disable or uninstall the OHCD controller, none of my devices work even with the Enhanced controller still available. I'm at my wits end on how to get this taken care of. Any advice would be appreciated it.

Quote from: Supershanks on 03-May-05, 18:58:16
Bataar,
You don't say which neo4 you have as there are 7 models this can be abit confusing. Which NF4 Motherboard Do I Have.
on the 7100 SLI versions the bios option is as described in my 1st post the onboard devices section.
on the 7125 Ultra versions Bios the USB Controller is in Integrated peripherals.
options are the same in both.
I do have the 7125 board and under Integrated Peripherals, the only option as far as the USB Controller is enable or disable. That's it.

Similar Messages

MSI K8N Neo4-F Problems

I'm on my very first build and I'm running into problems. When I power up, all the fans spin up properly and the D-Link LED's go through the usual settings but it gets stuck on the combination that the manual translates into "Initializing Floppy Drive Controller - This will initializing Floppy Drive and controller." The D-Link LED's just hang there and I've left it alone for a couple minutes and it still wouldn't budge. On the screen, sometimes I can see the POST message and other times I see nothing at all on the screen from the various times I've restarted the computer. Any idea why it's hanging on this certain combination and not booting me to the BIOS setup screens? These are my system specs...thanks:
MSI K8N Neo4-F Socket 939 NVIDIA nForce4 ATX AMD Motherboard
AMD Athlon 64 3500+ Venice
ZALMAN CNPS7000B-AlCu Heatsink
Antec TRUEPOWERII TPII-380 ATX12V 380W Power Supply
OCZ Performance Series 1GB (2 x 512MB) 184-Pin DDR SDRAM DDR 400 (PC 3200)
Western Digital Caviar SE WD800JD 80GB 7200 RPM Serial ATA150 Hard Drive
Leadtek 6600GT

I take that into consideration! But as hardware goes, no two are exactly the same. But let's not focus on that, as I believe it could be problems elsewhere.
Posted by: Talannon
Hi!
First, the problem is I made this computer for a friend and when I boot the computer it always freeze at startup. I hear the normal bip when you start the computer then I see the first screen where it says to hit del to enter SETUP but it freeze there. I can't even go into BIOS. I have 2x512 MB in dual channel and when I remove one I can usually be able to go into the bios, then once there I check if everything is there by default ( I already reset cmos ) and it looks good then I reboot and it freeze again. I really don't know what to do...
But I will tell you the whole story. First I get the computer and at first boot I get no video signal. I see that I forgot to put the spacer between MoBo and the case. Then I fix that, comp boot I go into bios. I made another error by setting the FSB speed at 400 mhz because I read that it was going at 400 (I forgot that it was 200 x 2) so I reboot and I get nothing. I reset the cmos by pressing the button then i can get into bios.
From there I changed the boot order and I make it so MSI doesn't show his logo when you boot but you get the POST instead. I exit and save then I start getting that problem... Since then I am not able to go into BIOS unless I play with the memory module. Another thing is when I can't get into BIOS I watch the 4 LEDs on the USB thing you add to the MoBo (definition here http://www.msicomputer.com/support/sup_tshoot.asp#1_3 scroll down a bit). When I can't get into BIOS I get a combination (1 and 3 red) saying "testing base and Extended Memory, Testing base memory from 240k to 640K and extended memory above 1MB using various patterns" and when I changed the memory and I get into the bios (2 red) I get " Initializing Floppy Drive Controller, This will initialize Floppy Drive and controller". I got that from the book that came with the board.
The comp is:
MSI K8N Neo4-F
Athlon 64 3200+
MSI NX6600 TD 256 FX6600 PCI-E
Antec SLK1650 MINI TOWER CASE 350W
Kingston 1024 MB DDR400 Dual KVR
Maxtor 120Gb S-ATA
If anyone can help I would appreciate it! Thank you!
Posted by: Talannon
I will add that I tested the ram on another computer and it works fine. Also, when I only have 1 module of ram installed he start to detect the ide drive and sata HD but when It get to the floppy it fail. From there I can go in the bios but when I restart he won't even start detecting stuff he will only freeze after he wrote the memory testing line and then I can't do nothing... or I can hit continue and it even got started with the windows xp install but it crashed, it didn't take long. Reboot and crash at verifying DMI pool data or something like that after I hit continue again after detect floppy fail.
I tried resetting the cmos then reboot and it said that my config was in overcloaking mode and to reset it on the bios... But there was nothing to change. Also tried to continue there but it stop at Verifying DMI Pool Data.
The bios installed by default is v 1.3, which is the only version there's not on the msi website... strange
Anyway I pretty much said all I could, hope someone could help but I have a feeling that the MoBo as problem...
Posted by: keymaker
hmm......try takin out all of thec computer parts out of the computer case and this time only reseat the following devices: case, motherboard, cpu, ram, and videocard.
also try replacing the floppy cable and see if the computer will be able to detect the floppy this time. good luck
Posted by: Talannon
It still freeze the same way with only cpu ram and video card on mobo...
Posted by: zach1288
Try leaving your battery out longer, Some CMOS batteries can take up to 8 hours to clear.
Posted by: linderman
Welcome to TSF:
two items for consideration
A) what is your power supply and specs / this is by FAR the most underated overlooked component that plays such a vital role / the generics PSU just plain cant cut the mustard / they rely on cheap price to lure sales not performance / it doesnt take much of a fluctuation in power to send the newer systems baulking.
B) download and run memtest86.com on your memory modules / sounds like you may have a trouble maker there. Test them one at a time first / then as a pair
please post back with your findings
regards
joe
Posted by: Talannon
It could still play a role if I go back in bios and the settings seem to be back at normal? (like the FSB at 200 instead of 400 mhz like I tried to change at first.
edit: Power supply is a 350W smart Power by Antec
Posted by: Tumbleweed36
Hi,
An Antec is a great power supply, but frankly, don't think a 350 of anything is big enough to handle what you have. Even an Antec, you probably would need a minimum of a 450 to 480 with a very strong amperage rating. Antec and Enermax is where good power supplies are made if the wattage is what you need. That is the first place I would look after the memory thing is checked.
Posted by: Talannon
So... I made the test with the ram with this computer and the ram seems to have no problem at all.
So I guess I should try with a better power supply? But even a 350W with only the motherboard, cpu/fan, ram and video card would still not be enough to run it? Because I still have problem while running only that... Before I go out and buy a good power supply I would like to make sure it could be the source of the problem.
BTW, thank you all for the help so far, I hope we can find the problem :(
Posted by: Tumbleweed36
Hi,
If you have a Best Buy nearby, go find a good power supply and if it is not the problem, take it back or return it. That way, it would not be an expensive venture that might not solve the problem. Just be careful how you deal with the packaging so you can return it if it does not help. That sounds like the best solution at this time.
Posted by: Talannon
Ok, one other I will add is I noticed a trend. If I start the computer I can usually go all the way and start windows installation but it will stop working right after I hit enter to actually start windows installation. If I reset it will always hang at the beginning and unable to even get into the BIOS...
If I put the ram in dual channel setting it won't even start on first startup. But if it's on single channel it will at least let me go to the bios and such (but never recognized the floppy). Dual channel take more juice to run?
With this in mind is it possible that the mobo and/or cpu still be the cause of the problem?
Anyway I think I will try to get a power supply of at least 450W to test it. Just for testing purpose, can I get any power supply even if it's not antec or enermax as long as it has high voltage? I can test it and if it's working I can always return it and go buy a real power supply from antec or enermax where there is one.
Posted by: ginger6
I dont think it is your power supply, the power supply you have should handle what you have got no problem, the problem will be your memory...... are the 2 memory sticks you have identical, ie: same manufacturer, same speed, same chips on the board..... to run in dual channel mode you need both sticks to be exactly identical otherwise you will have problems.
What brand is the memory, if it is a cheap brand then you may have compatibilty problems.
Have you run memtest86 when both sticks are inserted but not in dual channel mode?
Kevin
live links of this type are no longer allowed outside of the advertising form
dai
Posted by: Tumbleweed36
Quote:
Originally Posted by Talannon
Ok, one other I will add is I noticed a trend. If I start the computer I can usually go all the way and start windows installation but it will stop working right after I hit enter to actually start windows installation. If I reset it will always hang at the beginning and unable to even get into the BIOS...
If I put the ram in dual channel setting it won't even start on first startup. But if it's on single channel it will at least let me go to the bios and such (but never recognized the floppy). Dual channel take more juice to run?
With this in mind is it possible that the mobo and/or cpu still be the cause of the problem?
Anyway I think I will try to get a power supply of at least 450W to test it. Just for testing purpose, can I get any power supply even if it's not antec or enermax as long as it has high voltage? I can test it and if it's working I can always return it and go buy a real power supply from antec or enermax where there is one.
Hi,
Before you go out and get another power supply, you need to make sure you have everything hooked up correctly.
Try flipping the floppy cable over and see if the BIOS recognizes it. That is a common mistake that all of us make from time to time. The red stripe (pin 1) goes toward the power plug on that one and it is opposite as a rule from the other ribbon cables, because the normal power plug on the hard drives have the power plug on the opposite side.
Second, tell us exactly what drives you have and how you have them hooked up...here is an example: Maxtor 30 gig IDE, set as master, on the end of the ribbon cable, and connected to IDE #1.
Third, the memory thing does seem to be an issue. Is the memory that you have listed on the QVL list in the motherboard manual?
For now, for testing purposes, just leave one stick of Ram in the board, and do follow the instructions in the manual about where that single stick should be. As an example, some boards require that when you use a single stick, that it is in Dimm2, Dimm3, or even Dimm4 instead of Dimm 1. That feature is new to some who don't regularly build, so please check that out before you go too far.
Let us know these things and we will try to get right back to you.
Posted by: Talannon
Quote:
Originally Posted by Tumbleweed36
Try flipping the floppy cable over and see if the BIOS recognizes it. That is a common mistake that all of us make from time to time. The red stripe (pin 1) goes toward the power plug on that one and it is opposite as a rule from the other ribbon cables, because the normal power plug on the hard drives have the power plug on the opposite side.
It will only go in the way I put it. Other thing is the power supply is an ATX with 20 pin. My manual says it should work but it also says that I could use a 24 pin SSI power supply but never use those. Again I am sure the power supply is in correctly cause I couldn't plug it any other way anyway.
Quote:
Originally Posted by Tumbleweed36
Second, tell us exactly what drives you have and how you have them hooked up...here is an example: Maxtor 30 gig IDE, set as master, on the end of the ribbon cable, and connected to IDE #1.
Maxtor 160 gig connected on sata 1 and there doesn't seem to ba master/slave option. Is it because it's SATA? It also seems to be detected as IDE THIRD Master on the first page.
LG DVD +/- RW in master on ide 1
Nothing on IDE 2
Quote:
Originally Posted by Tumbleweed36
Third, the memory thing does seem to be an issue. Is the memory that you have listed on the QVL list in the motherboard manual?
My ram is PC3200 (DDR 400) it's supported from what I can read in the book
Quote:
Originally Posted by Tumbleweed36
For now, for testing purposes, just leave one stick of Ram in the board, and do follow the instructions in the manual about where that single stick should be. As an example, some boards require that when you use a single stick, that it is in Dimm2, Dimm3, or even Dimm4 instead of Dimm 1. That feature is new to some who don't regularly build, so please check that out before you go too far.
Manual says it should be in a green slot first which is dimm 1 and 3. I put it in dimm 1 ans it should be fine. The setup like it is now, is in the combination list in the manual.
Posted by: Talannon
Quote:
Originally Posted by ginger6
I dont think it is your power supply, the power supply you have should handle what you have got no problem, the problem will be your memory...... are the 2 memory sticks you have identical, ie: same manufacturer, same speed, same chips on the board..... to run in dual channel mode you need both sticks to be exactly identical otherwise you will have problems.
What brand is the memory, if it is a cheap brand then you may have compatibilty problems.
Have you run memtest86 when both sticks are inserted but not in dual channel mode?
Kevin
I've only run test with the ram installed separately...
I also bought my ram as dual channel so I got a kit from Kingston KVR. So they should be identical to each other. Kingston is in the list of supported memory on MSI webpage of the motherboard...
Posted by: Talannon
So I tested the both ram at the same time but in single channel and no error.
One thing I notice is when I boot the ram is showed to go at 201 mhz instead of 200. Not sure if it says something...
Posted by: whodatknocking
Quote:
First I get the computer and at first boot I get no video signal. I see that I forgot to put the spacer between MoBo and the case.
this might be a real problem, we'll see
but first:
go into your bios and relaxe the timings on your ram, maybe 3-4-4-8
pump the voltage up on the ram a notch,to maybe 2.7 or 2.8
post back
Posted by: Talannon
humm I'm not sure what I should be looking for in the bios for that.
If I put Timing mode in manual instead of auto I can change a bunch of thing. I have no idea what you mean by 3-4-4-8... There is something in that called CAS# latency (Tcl) which is by default at 2.5 but could change it to 2.0 or 3.0. Is that the voltage?
Posted by: whodatknocking
try 3
no it isnt the voltage, the voltage would be in another spot in the bios
post back
Posted by: Talannon
changed nothing
I guess I am to a point to check the cpu on another socket 939 MoBo to see if it's the cpu or the MoBo the problem. With everything we tried I start to doubt it could be anything else.

MSI K8N Neo4 Platinum SLI sound needs -5V; newest Antec 550W has no -5V rail

I came within a whisker of ordering a non-returnable 3700 Venice, MSI K8N Neo4 Platinum SLI mobo and an upgraded Power Supply, Antec's newest 550W PS the TP2-550 EPS12V ($117). This has dual 2x24pin 12V 19A rails and is touted as the new V2.0 EPS12V/ATX12v compatible power supply for high performance SLI systems. By accident I came across a page at MSI for this mobo
http://www.msi.com.tw/program/products/mai...ail.php?UID=641
At the end is this warning: MSI Reminds You...
• For this model, you must use a Power Supply which has a -5V pin supply. Also, the users manual which I downloaded on Pg 2-10 says the same thing
The above Antec PS specs do not show a -5V rail, nor does an Enermax 600W I looked at. The V2.0 specs for ATX12v which added 2x24pin 12V rails dropped -5V rail from the spec and it appears MSI is not conforming to the spec (See Antec response at end) None of the web sites selling these PS & mobos contain any warning. I vaguely recall from a forum a while back it may have something to do with the Soundblaster system in the mobo.
http://www.antec.com/us/productDetails.php?ProdID=22551 (click specifications)
Isn't this a major showstopper which is going to cause a lot of grief for those of us upgrading to SLI systems using this mobo and upgrading our PS to the newest & best power design? We won't know the PS won't work until we build the system.
Regards, Ron
Antec reply to me:
>>>>Thanks for the link. Since MSI's website does state the motherboard needs the -5v, the True550EPS12V will not work with this motherboard. The Standard (http://enhanceusa.com/documents/atx12v_v2.01.pdf) has removed the use for the -5v rail and it is no longer needed. MSI has not manufactured that motherboard to the Standard. Finding an ATX12V v2.0 power supply with the -5v might be hard to find. You should contact MSI for a compatibility list of power supplys that were tested to work with the K8N SLI Platinum.

Quote from: ccve3 on 21-May-05, 07:27:40
Wow!! syar2003 thanks for that post. I've spend an hour going through it & fasteddies links. Now I are a power expert. The dual rail argument is enough for me to go back to the MSI K8N Neo4 Platinum SLI with one of the single rail PS -5V units listed by fasteddie. The only question left now refers to computerpro3 recommendation on ultra power supplies for SLI
>>I quite simply wouldn't dream of putting anything else in my machine. Keep in mind, this section is for 2x 6800 models, not the 6600's which most any good psu will handle (like Antec Neopower, ocz 520, etc). . Pc Power and Cooling 510 Deluxe SLI edition (refer to list)
2. Zippy/Emacs 550-700w models
3. OCZ 600w (personally I would get the pcp&c for the price, but it's been proven here, so I'll be fair...).
These are really high end, expensive and only 3-4 choices. Since I'm getting one 6800GT and eventually another & possibly eventually a 4800 X2, I was hoping the OCZ 520W would do it but computerpro3 says Powermaster 520 isn't good enough for SLI. I found that there is an OCZ 600W ATX12 dual rail which surprisingly has a -5V rail needed for K8N Neo4 SLI Soundblaster. Will this meet computerpro3's preference for a high end PS for SLI systems even though I'm losing the 1 rail advantage. Maybe the 600 Watts just overwhelms the 1 rail/2 rail question.
Thanks again for the teriffic help
Regards, Ron
Wondering what you settled on. I got the Antec TP550 and it's flawless on the board. I even have the older 20pin model which works perfectly (including sound). If you really wanted what I would consider to be a top dog (pcpower and cooling), and find the -5v rail missing, all you have to do is place a phone order and request they add a -5v rail. It's a minimal cost and a total solution for having everything. Just my $0.02

MSI K8N-Neo4 and PCI-E x4

Hi Folks,
I've got an MSI K8N-Neo4 (MS-7125) motherboard that I'm looking to add a RAID card to. It's got a PCI-Express x4 slot on the board that I'd like to utilize. However, I've seen some conflicting information regarding it's use. In the manual on page 2-26 it states "PCI Express x4 Slot (Support PCI-E x2 device Only)". However when I look at the webpage for the board at http://www.msicomputer.com/product/p_spec.asp?model=K8N_Neo4_Platinum& it makes no mention of this limitation.
The main reason why I'm wondering is because I'd like to add a HighPoint RocketRAID SATA raid controller to my system. If the slot can handle x4 cards, then I'll purchase the 2310 model, which is an x4. If it cannot, then I'll purchase the 2300, which is an x2 model. I've seen some mentions of other people on the forums with K8N-Neo4 boards using the 2320 (an x4 card with 8 SATA ports instead of 4 on the 2310), but haven't seen what sort of bandwidth they're getting. Are you actually able to get PCI-E x4 bandwidth out of this port? Or will it downgrade it to PCI-E x2 or PCI-E x1 (the PCI-E spec says that when cards a plugged into a different size port they only need to be supported at x1)? Or, and even better question, will it even work?
Thanks for any help you can provide.

Quote from: Bas on 09-July-06, 07:25:26
Those are not different then from what's on the motherboard
Want a real one? Look at this: >>Real one!<<
That's real raid controller.....
What you mention is just the same as the onboard stuff.
As for the Linux raid stuff, I presume you mean the Linux Software raid, no those controllers aren't that good, but the High-points aren't that good either.
Heck, they don't even have their own CPU or memory.....the one I showed you has and is WAY faster
(PS. sample given is PCIx, won't fit your board, but that's a raid controller!)
Okay, that still doesn't answer my question about the PCI-E slot. You make a decent point, but I was more using the Highpoints as an example and because they came up in several searches of the forum. For the sake of getting a real answer, lets assume it is a real RAID card, such as the PROMISE SuperTrak EX8350 RTL, which according to the Serial ATA on Linux page is a real raid card and all that. Will it work in the PCI-E x4 slot on the MSI K8N-Neo4 Platinum or not?
All I really want to know is if the slot can actually run a PCI-E x4 card or not. The documentation contradicts itself.

MSI 6600GT PCI-E or MSI K8N Neo4 Platinum ?

Dear Sirs,
I've just bought a MSI NX6600 TD GT 128MB PCI-E and
Motherboard MSI K8N Neo4 Platinum.
I Think that one of these is defective bacause WinXP can't work with MSI original drivers, MSI old drivers or Nvidia drivers. The system reboots.
I think that i've tried almost everything and this card only works badly with VesaSave driver (Generic Windows driver).
Could a defective video card works ?
Is it possible that the problem is the Motherboard ?
Any idea ?
Help me please,
Thank you very much,
ISW
MSI K8N Neo4 Platinum
A64 3500+ Winchester
Original Cooler
DDR PC4000 GEIL 1GB ULTRA DUAL
MSI NX6600 TD GT 128MB PCI-E
Maxtor 120GB
Seagate 120GB
XP Home SP2

About PSU I'm a old (41 years old) newbie, and I had to re-assemble my old computer to work but I check this before with MSI software and at motherboard bios voltage check and remember that it was ok it is a 600 watts. But I think that even if it is not, I could at minus install the driver and start Windows. I had no possibility to even start Windows.
If I install any MSI or Nvidia driver, when loading WindowsXP the screen turns black and at some time after the system reboots and prompts to start in secure mode. So I can't do anything, even starts Windows with this videoboard with right drivers. It only works with "VesaSafe" driver.
ISW

New build: MSI K8N Neo4 Platinum + maxtor 300gb = problem?

Got these 2 products included in a order:
MSI K8N Neo4 Platinum nForce4 Ultra (Socket 939)
Maxtor DiamondMax Plus 10 NCQ 300GB
While checking up on the MB on the MSI site, I noticed a version of the bios (1.2) that says 'support for 300gb maxtor drives'
That's the same HD one I have coming with my order >.<
If the MB I get hasn't got that version of the bios already installed will I have trouble installing the drive?!
I downloaded the bios and it says in the readme not to install it from a floppy disk, so I guess you need a system up and running to make that update in the 1st place. No Idea how to go about this, if the need arises.

Quote from: Supershanks on 19-May-05, 21:45:00
Hi drjugears,
Welcome to the forum.
Many people are runnimg ok anyway as dope says.
But it's not an issue you can update the bios via floppy b4 connecting the maxtor.
See Flashing the BIOS for Users using NON FAT file system This is a guide written by msi. Strictly speaking if you folow the instructions you aren't flashing from a floppy the actual update is done on a virtual drive in memory.
if you need a floppy boot disc see Why no floppy for bios flash?
luck with build
Thanks very much for the welcome and info.
Unfortunately I'll have to wait a while to see...I installed everything....but need some adapter for the 6pin connecter on the ATI card. The power supply came with some 8 pin one. So I need a 4 to 6 pin adapter. Doubt If I'll find one local, so will probably have to wait until monday now to try it out.

Maxtor 6Y160MOSTD 160GB DiamondMax Plus 9 SATA/150 -- on -- MSI K8N Neo4 Plat...

Hello there... I have a Maxtor 6Y160MOSTD 160GB DiamondMax Plus 9 SATA/150 on my MSI K8N Neo4 Platinum. I've had this problem before but it wasn't important enough to report until now.
I have the latest BIOS (1.B)
Now... I did have a dual boot - XP and Fedora Core... then I decided since Linux would only install the base text system, to get rid of it. I formatted using Windows disk manager. BUT the GRUB MBR was still on there. It resulted in an error. So I took my winXP disk and popped it in. I tried to first repair the MBR. I used the command BOOTCFG DEFAULT. that didn't work. So without thinking I decided to reinstall XP all together. When It got to the restart, the GRUB was still there, therefore didn't boot. Well what I ended up doing is trying the repair again. Used the command FIXBOOT - didin't work. I tried agian. Repair - found the command FIXMBR DUH! So I ran that and it recognized that the original MBR had been replaced. So I fixed the MBR and rebooted. XP wanted to install. So I let it. I came back some time later and found out it was stuck on "Initializing Devices...". At first I thought it was the graphics card. b/c linux had problems before probing the graphics card. I decided out of the blue to swap my 160GB HDD for a smaller PATA 2.1GB HDD and installed XP seemlessly. The obvious reason: XP couldn't detect the hard drive. The reason this is confusing is because I installed XP before on my HDD and no problems. I tried figeting with the chords, switching SATA slots. No luck. I really wanna know whats up with that. Help PLEASE.
Did I leave some info out?

Have you tried to download the Firmware for your HDD? Maybe you can refer to this site ==> https://forum-en.msi.com/index.php?action=profile;u=77029

No Post/Black Screen - MSI K8N Neo4 Platinum

Hello,
Here is my problem, I bought MSI K8N Neo4 Platinum motherboard and got
- 3500+ cpu
- CORSAIR XMS 1GB memory
- PCI-E Leadtek 7800GT video card
- Aspire 520Watt PSU
I have put all of it together fine( I have put many systems for friends before) hooked all the power cables, case to mobo stuff, fans. Every time I turn it on fans go on, and lights go on but there is nothing on the screen as if no signal from video card to monitor, plus no error beeps which means cpu and memory is fine right. I have tried to just have memory, video card and nothing else hooked up, same result. I have tried another PSU, same result. Now to add to this, I had same problem with ABIT motherboard and another video card(same) which eliminates bad motherboard and bad video card, since both I have replaced except this time I got MSI mobo and not ABIT. I got same problem with all of it, nothing comes up, no post while fans spin when I turn it on etc... What could be the problem? memory? case? Any ideas?
Please help me as I spent a lot of $ and time on this and had no signal to monitor so far. Thanks.

As I said at this point I am trying to boot without any drives plugged in just to get a post and boot up but no go. So basically all my drives are unplugged and I cannot get it to work, I have tried different psu and same problem. I have tried another video card( I RMA this one and got another) it goes and snaps into PCI E slot all good, I have checked that many times. The only thing I can think of is memory at this point but this is brand new XM Corsiar memory and why wouldnt the motherboard beep ( i hoked speaker) if there was any error like that? I just dont get what is going on.
I have no idea what bios version I have as I have been unable to check it, unless you want me to check the chip version on chipset?

Audigy2 + MSI K8N Neo4 Platinum nForce4 Ultra prob

Hi I have an audigy2 from my old pc and installed it on my new system the motherboard is a MSI K8N Neo4 Platinum nForce4 Ultra after I installed it I began getting 'Machine_check_exception' blue screen of death, I used the creative auto update to update to the latest drivers, now the pc makes a hissing sound and reboots it's self.
Any help would be apprecieated.

hi
i am getting th same thing with my gigabyte nforce 4 board
ga8nxp-sli
could this be an nforce 4 related issue?
i found through a process of elimination that the conflict apears to be with windows audio service
i turn it off and all the problems just go away but i still get no sound (not much help there i am afraid)
regards
andy

NVIDIA Network Adapter problem (MSI K8N Neo4-F)

We have an MSI K8N Neo4- F motherboard. We are running Windowx XP SP2 (just upgraded to Service Pack 2). The computer will only boot in Normal mode if we disable or remove the NVIDIA Network Adapter driver. If we attempt to boot in Normal mode, it always ends with a Bad Pool Header problem (Blue Screen of Death). If we boot in Safe Mode with Networking, we can access the Internet. If we disable or remove the driver, then boot in normal mode, we can run in Normal mode but we do not have internet connection.
Does anyone know how we can use the onboard Network Adapter, and still boot in normal mode?
We have been using the latest drivers from MSI for this motherboard. Is there a different version that can be used? Is it possible that we have to update our BIOS for it to work correctly with SP2?
Thanks!

I think I may have misunderstood what you meant by a clean install. I probably should have asked what you meant before I answered my last post.
If you mean "did we just build the system by wiping the hard drive, installing XP SP1, then apply SP2", the answer is no. The system has been running Windows XP SP1 for several years without any problems, and we just wanted to upgrade to SP2 because there is some software that we want to load that requires SP2 to run. We have lots of software loaded on this machine that we use every day that we really want to avoid (short of time right now to tackle that project) rebuilding the entire operating system/machine because of the work involved in reloading all the software, etc.
Am I correct in assuming that we would have to wipe out the hard drive and start over if we did a re-install from a slipstreamed SP2 cd? If so, then we will probably just stay with SP1 for the time being if there is no other option to fix this Nvidia driver problem until we have more time to do a complete re-install and reload of the computer.
What about just installing a NIC in one of the PCI slots and use that instead of the onboard NetWork Adapter?
Thanks for all your help.

MSI K8N NEO4-F SATA ISSUE

System Specs:
MSI K8N NEO4-F
x2 512mb Corsair Xtra Low Latency 2-2-2-5
VisionTek x850XT
Creative Audigy 2 Platinum w/ Live Drive
(1) WD Raptor 10k rpm 74gb (SATA)
(1) Maxtor 300gb (SATA)
(1) Maxtor 200gb (IDE)
(1) Samsung 52x32x52 Burner
Windows XP Pro
Recently built system but I'm having SATA performance trouble. Let's start from the boot process. Sometimes when booting, the system will hang while detecting drives, and not detect my 300GB sata drive. A simple reset will sometimes fix this. If allowed to continue to boot, a blue windows XP error screen briefly flashes and the system reboots itself. Going into the bios and trying to autodetect the drive causes a long hang and no detection.
Moving into windows if everything seems to detect alright, sometimes the 300GB drive seems to function perfectly well, and for as long as my system stays up. Other times I'll go to open some sort of media on the drive (like video), and it will run rediculously slow, skipping and barely running.
I tried replacing the SATA cables, thinking that maybe they were bent too much or perhaps just bad, but after replacing them the problem seems to persist. This problem at first seemed confined to the 300GB, but my last boot to windows was crawling and anything i opened didnt respond, as the OS is housed on the raptor. So now it seems both drives are capable of this problem.
Does anyone have any incite?

Hi mjc2264,
It's the series 10 300gb maxtors that have been giving pps some issues not just with msi but all AMD64 Nvidia chipsets, its unusual to have Maxtor9 ?? give problems.
A number of things you might try:-
1) Bios Standard Cmos Features try changing the Access Mode for your 300Gb to Large instead of Auto.
2) Detection is sometimes Worse due to the Pata channel issues. If using the Nvidia IDE Drivers ensure your
Maxtor 200gb (IDE)
Samsung 52x32x52 Burner
are Jumpered explicitly as Master/Slave the NV drivers don't like CS (cable select). Ideally have 200gb on IDE1 & Samsung on ide 2.
3) If 2) gives no change Or if you feel the need Roll back The IDE drivers & try the MS Default ones
Click update driver on the Nvidia Pata driver tab in properties.
Choose install from a specific location
Select dont choose , i will choose the driver
Then select standard dual channel pci controller which is the XP 1
4) If Windows detects problems with drive access r/w errors it downgrades the drive access mode. If you have been having issues check in device manager IDE Ata/Atapi Controllers Right click properties on each tab & check access mode it s/be Serial ATA DMA for SATA & I think Ultra DMA 5 (or 6??) for Pata HD. If you find any down graded Set them back & XP will ask to reboot.
Luck

MSI K8N Neo4-F booting issues

Ok, well I'm a n00b and this is only my second build. When I first put everything together, the system started right up and I was able to reboot no problem to upgrade the OS etc. However when I gave it to my parents, it started having some problems booting. Sometimes it boots up right away (if it's been off for a while)...however if you restart it, the fans run, but nothing happens for several minutes. Then all of the sudden it beeps and starts booting like nothing is wrong! So while it's sitting there doing nothing, I checked the D-bracket and it looks like it's sitting on the processor initialization:
MSI K8N Neo4-F running Bios version is 1.9 - the only setting I changed was removing the logo
Windows 2000 SP3 which I updated to 4
AMD 64 3700 +
Power Supply - Antec smart power 2.0 500 watts
liteon DVD burner - IDE primary master
a single 250 GB SATA seagate hard drive which is partitioned into 2- IDE 3rd master
2 sticks of 1 GB Cosair Value Select
ASUS EN6200TC256 - Geforce 6200TC 64MB 256MB PCIe
I did try reading through the forums first. I'm not sure if I should clear the CMOS or flash the bios. At this point I guess I kind of lack the confidence to make a decision due to lack of experience and the fact that it's not my computer I'm messing with. So guys, can you help a girl out? Any advice is much appreciated

Quote from: bjk1 on 27-March-06, 22:22:19
Hello Jewels,
have a look at this thread: https://forum-en.msi.com/index.php?topic=80294.0
Maybe, it's the solution to your problem.
Bye.
Your link to the other thread was enlightening. A couple of things. My father did install a card reader. However, I'm unable to find those particular settings in the bios. My father also has logitech's mx3000 wireless keyboard and mouse hooked up. I unhooked the little reciever it came with and hooked up a standard keyboard and mouse, and what do you know, it boots fine. Which explains why I had no jproblems when I set the computer up initially. I'm sure he's going to want me to find a way to use them though.

MSI K8N NEO4-F

Hi
Im planning to buy a MSI K8N NEO4-F but my actual PSU doesnt have a native 24 pin support (im planning to use a 20 to 24 pin converter). Its a Nspire True Power 450W with 25A in the 12+ rail... my question is, that psu (with the adaptor) could be enoght for use with: 2 hard drives, 2 optical drives, 2x512 PC3200 sticks, geforce 6600GT or Radeon X850Pro????
Thanks!!!!!!!!

450W with 25A in the 12+................meaning DC output 12v is 25A is it???? my power supply got two 12v, the first 12v is 15A and second one is 17A......like this enoght for my com (2x512MB PC3200, one SATA2 WD 250GB hard drive, geforce 6600GT)....is it enoght....some time i get the blue screen when i startup win xp some time no.....is it my power supply not enoght power....need change it......????
and 1 more question is that my hard drive is SATA2 and my mother is only support only SATA1.....i like this use is it will cause problem like blur screen???

DDR 500 memory compatible with MSI K8N Neo4 Platninum?

Hi Folks,
I have a MSI K8N Neo4 Platinum PCB version 1 (S939/Nvidia NForce 4 Ultra), running the latest BIOS version. I wondered if DDR 500/PC4000 memory would work at DDR500 speeds? I note that the MSI webpage for this mobo only mentions DDR400 and in the manual, the BIOS description under "Advanced Chipset Features" - "Memclock Index Value (MHz)" says the maximum speed is 200MHz. However, when I go to this setting in my own BIOS, I can set it to 250MHz. I assume that this should give me DDR500? Would altering this "Memclock Index Value" above 200 MHz cause any other problems with FSB, CPU, HT, PCIe, PCI speeds etc. or is it completely independent? Does anyone have any recommendations of what sticks would work best (I was thinking 2 * 1024 Mb of Corsair XMS or OCZ XTC). Now that DDR2 is standard and DDR prices are creeping up, there doesn't seem to be much difference in price between DDR 400 and DDR 500 memory. Evern if my mobo can't support it, is there any merit in buying DDR 500 memory and running it at DDR 400 or intermediate speeds?
Cheers!

The x2 4800 would run 10x250=2500mhz.
With ddr500 it's beautifull,since you can use the cas latencies which are suited for the memory.
I have to lower my timings a bit to run them at 500mhz.Not much though,but I don't know what the long term prospect is for my memory if I maintain that for long periods of time.
As for running games,I found lower cas timings make my games run smoother opposed to the slightly higher ddr clock with slower timings.
But as mentioned,set cpu vcore 1 step higher in bios,leave the memory at auto,set cpu fsb or HTT at 250mhz,and use the default multiplier of 10 or also leave on auto.'The memory runs in spec and you wont damage it,only the cpu's get another 100mhz and should be a little bit more spicey while temps shouldn't go much higher as it is now.
The sticks should fit physically and I ran mine once at 266mhz stable,and they are just pc3200@200mhz

Considering the MSI K8N Neo4 Platinum

Hello,
I'm currently deciding whether or not to get the MSI K8N Neo4 Platinum, and I just have a few questions.
1) How beginner friendly is it?
2) Does it take a lot of work to make it run or can you just plug everything up and the system will run fast and stable?
3) How stable is this board? I've heard that MSI boards were unstable, so how stable is this specific board?
4) I know this board is good at gaming, but how about office work like using Microsoft Word, Excel, Powerpoint, etc.?
5) I plan to keep this system for at least four years, will this motherboard give a lot of trouble? And how reliable is it?
5) Can ya'll share your experiences with MSI?
Thanks for any help.

Quote from: ExpertNovice on 30-June-05, 03:43:00
Is the MSI website http://www.msicomputer.com/product/p_spec.asp?model=K8N_Neo4_Platinum/SLI&class=mb where MSI names the board as "K8N Neo4 Platinum/SLI" incorrect? It wouldn't be the first time a typographical error occurred.
If not then the OP may simply have not had enough room to enter a complete description.
No it is not incorrect, I am staring at the box mine came in. It says Platinum Edition-K8N Neo4/SLI, there is also a the non platinum version K8N Neo4/SLI and the non-SLI K8N Neo 4
anyway,
Quote
Maybe I'll get the Platinum SLI edition instead so that I can upgrade later to SLI without having to buy a new card. If I do get the SLI I'll use a single card for now and put in the second card later when it's needed. Does the MSI K8N Neo4 Platinum/SLI have any problems with running a single video card in non-SLI mode? And I've noticed that the SLI edition doesn't have a x1 PCIe or x4 PCIe slot, is sacraficing these two slots (as well as a regular PCI slot) worth it for SLI capabilities?
to answer that question, no it does not have problems running a single card in non SLI mode. It runs like a champ. I pernonally would not use the extra PCI slots, so to me SLI outweighs scarificing the extra PICe slots.

MSI K8N Neo4 not recognizing USB 2.0

Similar Messages

Maybe you are looking for