MSI K9N NEO - Whats the best geforce ?? MY 6200 LE WONT WORK !

Hi all.
When i turn on the PC with the Geforce 6200 LE in the PCIE slot... the graphics are seriously messed up. red lines and blue bands down the screen and strange characters everywhere.
Only way I could install windows onto the new blank HD was to put in an old PCI graphicswe card and like magic... its normal. Now i used the old card to get me onto the internet and got every new driver for the geforce 6200 LE I could find, but no matter which driver I apply the pc just wont boot with the 6200LE in.
My system spec is
K9N Neo MS-7260
AMD Althlon 64 3200+ AM2
1gb GSkill DDRII 800 RAM
"3DFusion" Geforce 6200LE
Could it be the fact that 3DFusion cards are not compatible with the K9N Neo or nforce 550 and if so... presumably I need either an NVIDIA geforce or an MSI geforce rather than my 3dfusion card ???
So to sum up guys... shall I sell the 3dfusion geforce 6200LE and buy an MSI Geforce.... and if so... which card will DEFINITELY work with the nForce 550 / K9N Neo ???
It seems 3dfusion cards arent compatible with nforce550 or k9n.

Quote from: Steve Kilner on 09-September-06, 04:02:57
Hi all.
When i turn on the PC with the Geforce 6200 LE in the PCIE slot... the graphics are seriously messed up. red lines and blue bands down the screen and strange characters everywhere.
Only way I could install windows onto the new blank HD was to put in an old PCI graphicswe card and like magic... its normal. Now i used the old card to get me onto the internet and got every new driver for the geforce 6200 LE I could find, but no matter which driver I apply the pc just wont boot with the 6200LE in.
My system spec is
K9N Neo MS-7260
AMD Althlon 64 3200+ AM2
1gb GSkill DDRII 800 RAM
"3DFusion" Geforce 6200LE
Could it be the fact that 3DFusion cards are not compatible with the K9N Neo or nforce 550 and if so... presumably I need either an NVIDIA geforce or an MSI geforce rather than my 3dfusion card ???
So to sum up guys... shall I sell the 3dfusion geforce 6200LE and buy an MSI Geforce.... and if so... which card will DEFINITELY work with the nForce 550 / K9N Neo ???
It seems 3dfusion cards arent compatible with nforce550 or k9n.
do you have the VGA in the BIOS set to PCIE? I just set up my new comp with a 550 chipset and an ATI card and I'm pretty sure I changed the VGA setting in the BIOS

Similar Messages

MSI K9N neo - black screen

Hi everyone
I have a computer with a MSI K9N neo (v.1.0) motherboard. About a 1,5 years old. Until last week it was working fine, but after a hard disk crash (and replacement), i can't get it to boot properly. When i start it up, I can hear the fans and drive spinning, and i get a POST 'beep' (the usual short beep), but only a blank screen - monitor says No signal detected. I've replaced the graphics card with a brand new one, and it didn't help.
Can anyone help me?
Computer specs:
Motherboard: MSI K9N Neo
Graphics card: Gainward Bliss 7200GS PCX(new) - XFX GeForce 6200 TurboCache(old)
RAM: 2x Corsair Value S. PC5300 DDR2 512MB
CPU: AMD Athlon 64 3000+ 1.8GHz Socket AM2
HD: Samsung Spin point

Quote from: BOSSKILLER on 28-February-08, 17:46:46
Check monitor input selection 1|2
Check monitor cable and DVI->VGA converter if you use. Make sure that is filled well.
Try with different monitor
Thanks for the reply!
I've tried two monitors, two graphics cards and two PSU's - same result.
If I remove the graphics card and RAM and power up the computer, it does not beep at all, but when one of the memory modules (and/or the graphics card) are installed it beeps twice rapidly.. but the screen is blank no matter what I do..

MSI K9N Neo (AM2) memory troubles

Hi guys, I just got a new system which is having some issues, and I'd appreciate any suggestions on what could be wrong.
At first, the system simply crashed during OS boot. A quick test with memtest86 showed 50-60 thousand errors on a single run, so I asked at Corsairs site, got the recommendation to up the voltage to 2.1V. The memory got a whole lot more stable, but still showed a few dozen errors per run.
So, I proceeded to test the modules one by one, and found them operating well as long as only a single module was inserted (no errors on a 12+ hours run). I moved them around, tried different dimm slots, but as soon as both modules were in, there were errors ranging from a few to several dozen per memtest pass.
The system specs are:
MSI K9N Neo (nforce 550 based)
AMD Athlon64 3500+
Corsair Value Select 2048MB PC5300 kit (2 1GB dimms, 667 MHz)
Geforce 6600 video card.
BIOS settings are defaults (memory timing set from SPD) with memory voltage increased to 2.1 volt as per Corsairs suggestion.
Any suggestions? Is the MB shot, should I get it exchanged, or could there be some other problem?

Hi Raider,
I would not run in dual channel mode until you get at least one stick to run w/o errors in Memtest86. I had a similar problem with different memory but the same MSI K9N MoBo. Sometimes it passed and sometimes it did not. My two problems were (1) power supply, only 350W, so I jumped up to a 500W, and (2) memory timings. The MSI site said the MoBo has trouble with SPD timings. So try moving the mem speed down a whole bunch, like 166Mhz or 133Mhz clocking first. If it passes all mem tests, then move the clock back up and try to look up the memory timings for your memory and type them in manually in your BIOS. For me, I went from 2.5-3-3-8 2T to 3.0 5-5-8 2T and it ran forever. From Windows I used CPU-z to see the memory SPD and timings and set it to the lower settings from CPU-z to make it work the first time. This week I am taking back the memory to the store because it won't run at spec.
Good Luck
Dave T

MSI K9N Neo V1

I have got MSI K9N NEO V1 motherboard AM2. I use AMD Sempron AM2 3000+ CPU. I would like to upgrage 2X2Gb Memory 800Mhz.
Bios update 1.9 version.
If I upgrade 2X2Gb DDR2 800Mhz memory the screen is black, bios auto settings.
If I upgrade 2X2Gb DDR2 800Mhz memory and bios settings memory frekvency is 2X200Mhz=400Mhz or 2X266Mhz=532Mhz, Bios know 4Gb memory but OS doesnt boot.
What's the problem?
Can you help me?! Please help me! Thank you very much!

i didn't notice that they are different brands..
Quote from: keresek2010 on 11-June-15, 02:16:17
if I use slot 1 is Kingston and slot 2 is Kingmax: is OK , But I use slot 1 Kingmax and slot 2 Kingston : black screen.
I dont know thats why?
you should use matched memory sticks only [as Bernhard already told you]
if you a different one there is no any grantees that they works together
the only think you can try is to place the slowest memory stick in the 1st DIMM and other at other DIMM

Msi k9n neo v3

msi k9n neo v3, i have a problem with this board cuz bios want save settings so it only works on default values.
What is the reason this to happen??? COuld it be some bios failure or some hardware damage?!

The watts means very little:
Read here:
Add-on to read:
>>> PSU's---2 x 12v---The Dual Rail Myth <<<
>>> Is your problem caused by your PSU? <<<
and here: https://forum-en.msi.com/index.php?topic=112039.msg836246#msg836246

Msi K9N NEO @ MSI 7260 Front Panel Connectors Jfp1/jfp2

hi all..
currently i'm using icute ..0508ULA casing ( as illustrated below.. )
ok..i' ve successfuly connect front usb connectors ( JUSB1/2 ) & working fine..
the problems are : i've two connector like this : ( one with number : 1394 & another with no numbers..)
so,..i've refer to the manual book..but no idea how to connect it..
another thing is...my "power led" not working..." hdd led" & " reset button" working good..
there's 3 connector :
1. power switch ( orange & white )
2.reset switch ( blue & white )
3. hdd led ( green & white )
so how to make my "power led" working or need to modified it..?
( please refer diagram below..for msi k9n neo )
anyone using similar MOBO & case ( msi k9n neo & icute ..0508ULA ) COULD PLS advise me
many thanks..

Quote from: BOSSKILLER on 19-August-07, 15:04:24
so the problem is that you can't find the power led cable from the case? if yes, dunno how i can help with that...
search again for the cable.. must be somewhere in the case...
so the problem is that you can't find the power led cable from the case? if yes, dunno how i can help with that...
search again for the cable.. must be somewhere in the case..
dunno what tips more to give you except to suggest to use better glasses
YES..i dunno whre is it..
will open front panel..to see is this thinggy " hidden"..
anyway thnks BOSS..
will update later..

MSI K9N NEO-F V3 Cannot install Windows 7

I am trying to install Windows 7 Professional 64 bit on my wife's desktop computer.
The system is:
MSI K9N NEO-F V3 Motherboard with BIOS American Megatrends Inc. V2.4
AMD 64 X2 3.00 Gigahertz
2 Gigs of RAM
Windows XP Pro 32 bit
500 gigs SATA HDD
120 gig and 40 gig IDE HDDs
As it has to be a clean install, I start the computer with the Windows 7 in the DVD drive. I get loading files, Starting Widows and then the background picture (picture with vapour trails, a dove and some grass) for the "Select Language etc." screen. Then nothing, no matter how long I leave it.
Got onto Microsoft and spent 1.5 hours trying to get it to work. We even went into the BIOS, made sure the DVD drive was the first boot device. When I clicked F10 to save and exit I did not get the "Press any key to boot from the CD/DVD", it went back to the beginning of booting.
The disk is OK, it is a Microsoft disk and worked fine when I tested it in my PC.
Can anyone help, please?

Disconnect the two PATA hard drives.
Make sure the hard drive you're installing Windows on is formatted before running the setup.

MSI K9n NEO v2/v3 change vcore 1.3v+

Helo.
I cant seem to change my vcore over 1.3v.
I tried changing from bios and using progs like crystal cupid and rmclock but it wont go over 1.3v.
any suggestions?
my specs
AMD athlon 64x2 4200+
MSI K9n NEO v2/v3
two 1gb OCZ XTC OCZ2VU800 1gb (not sure)
GeForce 9400 GT 1gb
idle 38c load 48-50c

all i want to do is change vcore over 1.3v.
Motherboard Name   MSI K9N Neo v2/v3 (MS-7369) (3 PCI, 2 PCI-E x1, 1 PCI-E x16, 4 DDR2 DIMM, Audio, LAN)
Motherboard Chipset   nVIDIA nForce 560, AMD Hammer
BIOS Type     AMI (03/17/09)
i have been searching all around for this for quite a wile so plz if anyone can gime a bios mod for this bod would be great!
my specs
AMD athlon 64x2 4200+
two 1gb OCZ XTC OCZ2VU800 1gb (not sure)
GeForce 9400 GT 1gb
i run xp sp2
idle 38c load 48-50c

MSI K9N Neo - MS7260

Well, I modified a BIOS again, for the MSI K9N Neo (PCB 1.0), MS-7260. The added features are:
- Damn Nice Bootscreen (the old one suck)
- Processor Frequency Multiplier
- Processor Voltage
I don't know if this will help some people with overclocking, but, here they are.
*USE AT OWN RISK*
http://rapidshare.com/files/228438450/MSI_K9N_Neo__PCB_1.0_.zip.html

hmm, unfortunately I can't seem to find that BIOS on my PC... I must have deleted it or something, but I did find a Beta BIOS in MSI's ftp site, which has EXACTLY the same changes. You can change the CPU Voltage & Change the Multiplier. You can download the BIOS here: http://www.mediafire.com/?o4t5mhomyzi
If you are interested in changing the bootscreen or modify some options, you can download AMI modding tools (MMTOOL v3.22 & AMIBCP v3.37) here: http://www.mediafire.com/?mnqwj2mmww2
I hope this helps. BTW, you should notice that this BIOS is for MS-7260 (MSI K9N Neo, PCB 1.0) only. It has nVIDIA chisets, so the CPU voltage will not be of much help, since nVIDIA uses completely different designs from that of Intel & AMD - nVIDIA's chipsets cannot overclock well, but they do have better latencies. Unfortunately real life performance depends on the actual clock rating & not the latency. You can try this BIOS, but I can't promise that it'll provide better overclocking. If you find that you can only overclock by 5%, then it's definitly better to leave the CPU on stock speed, setting the PLL's frequency higher than nVIDIA's chipset's locked frequency will make it unstable. Test the stability with IntelBurnTest (for AMD & Intel CPU's): http://downloads.guru3d.com/IntelBurnTest-v1.6-download-2047.html
*USE AT OWN RISK*

MSI K9N NEO (PCB 2.0) Help

MSI K9N NEO (PCB 2.0)
Problem with front audio connectors, In my atx i have this cords listed below..
MIC-IN
MIC-BIAS
SPKOUT R
RETURN R
SPKOUT L
RETURN L
GND
In the manual describing the JAUD1 Front Audio Connector it lists:
1. AUD_MIC
2. AUD_GND
3. AUD_MIC_BIAS
4. AUD_VCC
5. AUD_FPOUT_R
6. AUD_RET_R
7. HP_ON
8. KEY
9. AUD_FPOUT_L
10. AUD_RET_L
Guide me pls where should i put this cords because i only got 7 cords.
TNX IN ADVANCE

Your case connectors are not complient with the HD Audio connectivity standard. In order to make this work, you'll need to disable the Automatic Front Panel Jack Detection Function in the Realtek HD Audio Manager.
Connecting your case's ports should be rather either:
First of all:
GND ---> 2. AUD_GND
Then the microphone:
MIC-IN
MIC-BIAS
There are only two possible ways to connect these plugs to:
1. AUD_MIC
3. AUD_MIC_BIAS
Try both ways. One of them is going to work. [Remember: In order to make this work, you'll need to disable the Automatic Front Panel Jack Detection Function in the Realtek HD Audio Manager.]
And then the other thing:
SPKOUT R ---> 5. AUD_FPOUT_R
RETURN R ---> 6. AUD_RET_R
Same thing for the left channel. Just this time use:
9. AUD_FPOUT_L
10. AUD_RET_L

HT3819 I have 2 Ipod touch's, one a 64gb and one an 8gb. Whats the best way to use them both on the same itunes account?

I have 2 Ipod touch's, one a 64gb and one an 8gb. Whats the best way to use them both on the same itunes account?

Click here for options.
(64410)

Whats the best way to backup my iphone?

Hello. I am brand new to iphones....actually to apple anything. Never owned an apple product. I dont quite understand the whole itunes/icloud thing at all and I was hoping someone could explain it to me. All that I wish to accomplish is make sure all of my stuff on my iphone(apps, pics, music, etc) is backed up regularly and in the event that my iphone is lost/stolen, breaks, needs to be replaced for any reason, or if I upgrade to a new iphone I would like to be able to recover everything.
    OK, so far I have itunes installed on my laptop and I "sync" with that regularly (pretty much whenever I install a new app). But is my understanding correct that by syncing with itunes all of my stuff is stored locally on my laptop? If that is true, then what happens if my laptop crashes? So thats where I thought icloud came in. So I started backing up to icloud (via wifi in Settings>icLoud>storage&backup). But I notice that when I backup this way it is actually only backing up a small amount of data (in-app data??) rather than the entire app.
    I thought you would be able to sign into icloud.com and be able to view everything that you have ownership of or what you have backed up but that is not the case. I did download the icloud control panel to my laptop and it shows a little more information.
    So bottom line is I just need someone to explain how this stuff works and what the best course of action is for me to take regularly to make sure everything is safe, Thanks everyone! I sincerely appreciate any help you can give me!!

bjs19781978,
There are 2 ways to back up as you have stated. iTunes or iCloud.
You are correct in saying iTunes backs up everything on your computer. If you do lose your computer though, you will lose that information, but you would most likely still have your phone unless you lose your computer and phone at the same time which would royally suck.
You can also back up to iCloud like you have said. iCloud does not back up in the exact same way as iTunes, it only backs up application data, contacts, address books, and a few more things. The advantage to this is it does it automatically if you are connected to wifi, the phone is locked, and the phone is plugged in.
Look at this link to see exactly what iCloud does back up. Hopefully this helps a little.
Apple - iCloud - backup

Whats the best way to transfer everything from my old macbook pro to a new mac mini, i have a external hard drive which i backup to regularly via time capsule

whats the best way to transfer everything from my old macbook pro to a new mac mini, i have a external hard drive which i backup to regularly via time capsule

Check out > OS X Lion: How to use Migration Assistant to transfer files from another Mac

Wipe my hard drive clean except for the OS whats the best way?

I need to wipe my hard drive clean except for the OS whats the best way?

From Kappy (note: with this method, you will need to update to the present OS version using the appropriate Combo Update from Apple Downloads.)
Boot from the OS X Installer Disc One that came with the computer. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities (Installer menu if using Panther or Jaguar) menu. After DU loads select the startup volume from the left side list then click on the Erase tab. Set the format type to Mac OS Extended (Journaled) then click on the Options button. Select the one pass Zero Data option and click on the OK button. Then click on the Erase button.
Note: You can skip the Zero Data option if you are not concerned about removing sensitive personal data from the hard drive. If you choose to skip this part of the process then it is possible for others to recover data from the hard drive. The Zero Data procedure will prevent others from getting access to your personal information.
This process will take 30 minutes to several hours depending upon the size of the hard drive. After formatting has completed quit DU and return to the installer. Now complete the OS X installation. At the completion of the installation do not restart the computer. Instead just shut it off. The next user will be presented with the Setup Assistant when they turn on the computer just as it would if new out of the box.
https://discussions.apple.com/message/12364050?messageID=12364050#12364050

I want to connect a Mac mini to a Samsung 40", Whats the best way to do this?

I want to connect a Mac mini to a Samsung 40" LED tv to use as the monitor, whats the best way of doing this?

Understand that there is one HDMI port on your TV that is specifically designated for PC connectivity. The order that the TV or Mini are powered on may determine your results. For your specific TV model, check buyer reviews on Amazon or elsewhere that can include optimum TV/Computer settings adjustment for improved viewing results.

MSI K9N NEO - Whats the best geforce ?? MY 6200 LE WONT WORK !

Similar Messages

Maybe you are looking for