MSI K9N ULTRA 2F & PALIT 8800GT SONIC ISSUE

i have msi k9n ultra 2f and ati x1950gt. i decided to buy palit 8800gt sonic. but no monitor signal when i put palit 8800 gt sonic. everything works but no screen. then i replace my old card, working pc at the beginning. it says like this : " your bios settings overlock stopped to work. system back to previous settings. " like this.
palit 8800gt sonic changes my mobo's bios settings? there is any solution?  i updated mobo's bios but still same problem. pls help me.

Well do >>Clear CMOS Guide<< with power cord removed,
and leave just one memory stick in 1st DIMM close to CPU socket, then try to boot.

Similar Messages

  • MSI K9N Ultra (MS-7250 v2) SATA II ports dosnt work

    I have problem with 4 of 6  SATA II ports in the mainboard  (MSI K9N Ultra (MS-7250 v2)(SATA II 1~6 supports RAID 0/ 1/ 0+1 or RAID 5 mode by NVIDIA® nForce 570) doesn't work after install wrong program please help
    thanks

    why no any body help this pictures from my bois sitting and my problem I need help please
     MSI K9N Ultra (MS-7250 v2)
    bois pictures
    Here is functioning normally
    Here is functioning not normally

  • MSI K9N ULTRA 2F max vdimm (max DDR2 voltage!)

    1st:   I would like to ask you, the maximum voltage for the vdimm, that MSI K9N ULTRA-2F provides.
    2nd:  Will it work with OCZ PC2-6400 EL DDR2 1GB (2X512MB) GOLD EDITION GX XTC ?
    Greetings from Greece 

    Original 7250 supports 1.80 - 2.45v in 0.05v steps , latest bios is :7250v143
    K9N ULTRA 2F is MS7250-040 and use another bios , latest : 7250v31
    It supports DDR2-800 (PC2-6400) DDR2-667 & DDR2-533
    The OCZ DDR2 PC2-6400 Gold GX XTC Rev 2 Dual Channel 2 GB nominal voltage is 1.95 volt
    Latest bios for this board is
    K9N Ultra (MS-7250) V3.1 BIOS Release
    1. This is AMI BIOS release
    2. This BIOS fixes the following problem of the previous version:
    -  Update AMD NPT version.
    -  Update SB module version.
    -  Support AMD AWAY mode.
    Hard to say for sure if the VDIMM is the same (max 2.45v) since no manual is availible on any MSI location for
    this K9N Ultra-2F version (only found it at Japan site ) . But it should be the same .

  • MSI K9N Ultra -Failed???

    Hello. I have a problem. In my opinion, it is problem with my MB. I had a DVD-RW Samsung 203B (Sata). Problem: all DVD was closed (i use Nero 6,7,8 Ashampoo and i click Multisesion DVD and nothing), and DVD-RW detect as DVD-ROM. I change DVD, new is ASUS 2014L1T, I re-instal computers and it is same. DVD are closed and DVD-RW is detect as DVD-ROM. Where is a problem. I think, it is MB, but it is wrong Sata port (i change 5 port and nothing) or ....? Pls. I need help.
    Thank

    Quote from: BOSSKILLER on 26-January-08, 23:50:21
    What Nero report about the drive?
    Make sure that Nero is up to date.
    "Drivers I find MSI site. "
    Try with latest chipset drivers from Nvidia.
    "Apacer DDR2 1GB 800MHz  (3x)"
    Use 2x memory sticks only.
    Try with different SATA cable for the drive.
    Hi.
    I have a latest drivers.. I install new drivers from nVidia, from MSI for MB, i found new firmware for my DVD-RW (but is only 1.0)
    I use 1,2 or 3 memory stick. I change a 3 cable. I have instaled Daemon tool Pro with one virtual disc. I install daemon later, as I had a problem with optical drive.
    My info from Nero tools
    sorry: pictures http://s266.photobucket.com/albums/ii264/samurayy/?action=view&current=Infotool.jpg

  • MOVED: MSI k9n ultra-2f voltage problem

    This topic has been moved to Overclockers & Modding Corner.
    https://forum-en.msi.com/index.php?topic=121178.0

    Quote from: BOSSKILLER on 01-November-08, 04:22:10
    Look for extra vcore option in Cell Menu.
    oO ok i see it , thanks

  • K9n ultra-2f strange behaviour with 250htt and more

    Hi... My Pc:
    Athlon 4200+ Windsor F2
    MSI k9n ultra-2f , bios rev. 3.9
    2x 1024 DDR2 Goodram 800mhz
    Palit 8600 sonic+
    Chieftec 420w
    I have problem with overclocking more than 240htt... I turn spectrums off , and i set pci-e freq on 103. I also set processor multiplayer on 6 , mem on 400, and HT x2. The problem is that motherboard boot and works with 250 htt , even 300htt but... not always. It works good when i want to boot from shutted down pc, but when i try to change something in bios or reboot it from windows it's not working ( black screen , mobo doesnt boot ) ... I have to turn the pc off , and then turn it on again. Have you guy's some idea's about this problem ;/ ?
    I tried with diffrent HT multiplayer's , i saw also that in CPU-Z , with 250-300fsb it shows HT x1 instead of x2-3 which is set in bios.

    "The problem is that motherboard boot and works with 250 htt , even 300htt but... not always."
    High HTT freq is not important. Go for max CPU freq. and keep HTT below 1000.
    Leave CPU multi to Auto, drop HT link to x3, apply 667 memory index.
    Then start rising CPU HT with small steps and re-test.

  • How to overclock my x2 3800+ with K9N Ultra

    My current rig as below:-
    AMD X2 3800+ AM2 stock fan
    MSI K9N Ultra (MS-7250 v2.0 but on board stated v2.1) bios upgraded from 3.2 to 3.5
    1G DDR2 667 Kingston Value Ram x 2
    MSI 8600GT-Overclock edition
    Lite-on 20X Sata DVD-Ram
    Seagate Sata2 320GB
    WD Pata 120GB
    Cooler Master 500W Extreme
    Cooler Master Centurion 5
    As I'd seen in many forums that a lots of people are able to archieve 2.4G~2.6GB easily but I don't know why I can only able to archieve highest at 2.3G only.
    My current setting is as below:-
    Multiplier - 10
    HT - 230
    HTT - 5X
    FSB - 287.5
    Ram divider - 533
    Clock speed at 2300mHz stock vcore & vdimm 1.95
    But the moment I try to increase the HT to 240 or higher it tends to be unstable even I increase the vcore and vdimm.
    Can someone advise me on this matter.

    Quote from: BOSSKILLER on 10-May-07, 12:03:37
    "Besides that I'd also tried to set HTT to 3x and loosen the ram timing to 5-5-5-15-20 2T. vcore at 1.45 vdimm 2.0 and HT set to 240 but it won't boot."
    try with lesser steps. give CPU vcore only when need. what is your actual memory frequency at latest good OCed settings?
    "Btw I'd not seen the function "DOT & aggressive memory timings" where am I suppose to disable it?"
    aggressive memory timings option doesn't exist in your BIOS, DOT(Dynamic Overclocking) its Disabled by default, but ensure it.(located in Cell Menu).
    "My PCI-E has set to 104Mhz. Coz I'd seen some forum advise to set to 104Mhz. So actually 103Mhz or 104Mhz will be more stable?"
    nop will be the same.
    provide screenshots from CPU-Z with your last good known OCed settings.
    I'd set to disable on dynamic overclock all the time. btw I'd upload the link CPU-Z validation but I don't know how to put attachment thats why I upload the link.

  • Overclocking K9N Ultra

    I've been reading around the overclocking forum trying to find some definative information on overclocking on the K9N Ultra (using latest bios) but can't really find anything. I know my way around the bios  so if anyone could throw me some settings to change so I can get a decent speed . Spec in signiature
    - David

    i'll try to help you...
    my rig:
    AMD Athlon 64 X2 3800+ Windsor
    MSI K9N Ultra BIOS ver 3.6
    Corsair ValueSelect DDR2-PC 5300 2X512MB
    MSI RX 1300PRO
    Seagate 160GB SATA2 7200RPM
    DVD-RW LG
    HSF Scythe Infinity - Stock Fan
    <yours is better than mine>
    I OC from 2GHz to 2.8GHz <but, I prefer 2.7GHz, coz the temp. reach 67C on 2.8GHz>
    BIOS setting:
    go to Advanced Chipset Features -> MCP55 (SB) to AM2 (CPU) Freq. Auto DISABLED
    go to Cell Menu -> Cool n Quiet DISABLED
    CPU multiplier AUTO (10x)
    vCore = test by yourself <different rig = different result>
    CPU freq. / FSB freq. -> 270.00MHz <default 200.00MHz>
    Memory setting = I'm not good at setting my memory
    but, change vDIMM to 2.2V
    Spread Spectum -> DISABLED ALL
    any question??? ask me again....

  • K9N Ultra

    i have a problem the system is shutdown  and i don`t understanding why ?
    MSI K9N Ultra-2F,
    AM2 X2 Dual Core Processor 3800+ (default),
    NVIDIA nFORCE 570 Chipset,
    SuperTalent 2x1GB DDR2800 CL4 Dual Channel,
    Asus EN7300GT TOP 128MB,
    Samsung SATA2 160GB,
    NEC ND4550A DVD+RW/-RW/16x,
    NEC CD-RW NR-9500A,
    PSU FORTRON ATX-300PNR /300W

    Yes i tested it with a 400W power, but it is same.  my mobo from affected series of nforce4 ultra (7250-040). it rarely resets itself. is it a solution to use single core cpu insted of dual core cpu? or must i RMA it to distributor for certain solution?
    i have a mobo from affected series of nforce4 ultra.
    it rarely resets itself. is it a solution to use single core cpu insted of dual core cpu? or must i RMA it to distributor for certain solution?
    i have a mobo from affected series of nforce4 ultra (7250-040). it rarely resets itself. is it a solution to use single core cpu insted of dual core cpu? or must i RMA it to distributor for certain solution?
    MSI K9N Ultra-2F,
    AM2 X2 Dual Core Processor 3800+ (default),
    NVIDIA nFORCE 570 Chipset,
    SuperTalent 2x1GB DDR2800 CL4 Dual Channel,
    Asus EN7300GT TOP 128MB,
    Samsung SATA2 160GB,
    NEC ND4550A DVD+RW/-RW/16x,
    NEC CD-RW NR-9500A,
    PSU FORTRON ATX-300PNR /300W

  • K9N Ultra-2F walls at 260FSB!

    Hi,
    I have recently bought Msi K9N Ultra-2F mobo. And my cpu is x2 3600 brisbane. I have a pair of kingston ddr2 667 ram.
    A friend of mine also have this mobo too. But his processor is x2 4600. With his system i could do 290fsb by lowering the multiplier to 5x.
    But my mobo can only do 260FSB. And it is not stable. Sometimes i can go into windows with this FSB but immediately my systems crashes and gave me Multi Bit ECC error( I have no idea with this error).
    Now i am fully stable at 254FSB. But it is only 2.4ghz and this is too low for brisbane processors. I was expecting to go 300FSB+, when i was buying this mobo...
    I have tried lots of things, but none of them worked. Now i need suggestions for increasing my FSB.
    Regards,
    ChivaricKnight.

    Quote from: BOSSKILLER on 03-July-07, 05:55:34
    have you disabled spectrums & setup pci-e freq. to 103Mhz?
    provide screenshots from CPU-Z (main & memory pages)
    also read Moan Guide and list full system spec.
    Yes, i have disabled all spectrums. But set up pcie freq to 100mhz. Here is my cpu-z. I couldnt upload here correctly, sorry. I give the direct link:
    http://img522.imageshack.us/my.php?image=adszds6.jpg
    And my system specifications:
    Msi K9n Ultra
    X2 3600 brisbane
    2x1gb kingston ddr2 667 value ram(hynix chip)
    sapphire x1950gt vga
    WD 320gb Hdd
    Silverstone Strider 560W Psu

  • K9N Ultra-2F woes...

    Hello,
    I have a MSI K9N Ultra - 2F and for the moment an Athlon64 3500+ processor. Right know I am thinking of upgrading my CPU to a Athlon64x2. I did some research in the internet and all was well, until I found this post on your boards.
    Needless to say that my m/b serial number is 601-7250-050XXXXXXXXXXXX!!!
    The thing is that I bought this m/b 2 years ago. So, should I upgrade and if a problem occurs contact my local dealer (I bought this m/b from a computer store in Greece) or should I contact MSI directly if something goes wrong when I place the Athlon64x2 cpu?
    Thanx in advance

    Hello!
    The problem occurs when moving large files around. https://forum-en.msi.com/index.php?topic=100766.0;wap2
    If you should upgrade motherboard and processor, or just the processor, depends very much upon what you use the computer for.

  • 45.23's Resolved SBA Issue on MSI 5900 Ultra

    Couldn't enable SBA on MSI 5900 Ultra with 45.20 drivers. Fast Writes was ok. 45.23's resolved issue allows me to select, but have to reset after each reboot.

    The motherboard chipset drivers (excluding those for the onboard LAN and audio) were installed before the nVidia drivers.
    I re-installed the operating system (item 3 in my first post).
    P.S.
    Just used Driver Cleaner and tried again but still no joy.

  • MSI 745 Ultra SiS Install Issue

    I'm having HUGE issues installing this board. I've tried to read as many posts as possible to see if this has been covered, but didn't see it. here is what I have:
    Motherboard: MSI 745 Ultra Socket-A SiS745 / DDR333
    CPU: AMD K7 Duron 700MHz Socket-A
    Powersupply: 430W P4 Ready
    RAM: K-Byte 256MB-DDR 2100 PC266 184PIN DIMM
    Video: 16MB 3DFX VOODOO3 3500 TV-OUT AGP
    HDD: 10.2GB SAMSUNG IDE 5400RPM
    Fan: ANTEC Twister Socket-A / Socket 370
    skimpy, but logically possible, right? all pieces are brand new and all pieces have been tested in working machines... all except the motherboard. cpu, ram, hdd, & video all work until put on this board. I get power, but no video, can't hear the ram check, and the d-bracket sticks on all 4 red lights. if I could please get help with this it would be much appreciated. I tried starting with just the cpu, ram, and video hooked up to see if that helped... no go.
    thanks

    I tried installing a different video card:
    GeForce2 MX400 PCI 64MB
    this may be a dumb question, but i can still install a PCI vid card when there's an AGP available, right? it does not have the volts listed anywhere in the specs to let me know if this is 1.5v or not.
    i'm getting the same error.... all 4 lights on the d-bracket, no ram check, no beeps, no signal to monitor. but power to fan, power to led's.

  • K9N Ultra wont boot up anymore

    Hi, 1st time poster here.
    I have about 2 years old "K9N Ultra - 2F v. 2.1" non-SLi MB, wich just wont boot up anymore. I have readed the post about the same MB having some condensator problems, the sticky considerring it, and found that my MB should have the same issues as spoken there (S/N 601-7250-050Kxxxx....)
    But the problem at hand isn't about burning CD's/DVD's nor LAN or anything. I was gaming few days back and my PC and started to have FPS drops so i decided to boot it up, the problem consisted after boot so decided to check up temps and stuff, everything was ok. After booting up PC few times again the computer just didn't start up at all any more. It jams to the point where MB should give the small *beep* on boot and GPU should start sending info to screen. (Similiar to when you oc'd your PC too much and it wont boot up)
    So, i zeroed my bios with the button, and just to make sure took of bios battery for few mins and tried again, and the problem consists. I also tried with another (working) PSU & GPU but got no help from it.
    The rig consists of:
    MB: K9N Ultra - 2F v. 2.1 non-SLi
    Proc: AMD 2x 64 bulk processor, cant remember model no.
    Mem: 2x 512MB Buffalo 667MHz DDR2 SDRAM
    GPU: nVidia 7600 GT 256Mb (Also tested with nVidia 8800GTS 640MB)
    Any help given would be preciated, thank you.
    -skumbe

    Quote from: Fredrik on 21-January-09, 05:27:23
    Thanks for the update!
    The processor model per se should be no problem for your system. Image getting poor after a long while, well, sure it can be a graphics card problem but that should show itself immediately I think. Are you allowed to borrow your friend's PSU? Perhaps you have already?
    Like said earlier i have 550W PSU on main PC and i tried to boot up with it without any results, so lack of power shouldn't be problem.
    And for that color mixing problem, it starts out right at the point when i boot up. Its kinda hard to explain so i tooked few pics from what happens when i boot that PC up, here it goes:
    Quote
    Ok, so 1st off when i hit power button it gives post screen:
    Quote
    2:nd pic, just before that "Windows XP loading" -screen blinks up:
    Quote
    .... and theres the load up screen
    Quote
    windows boots up, prompts admin pass and goes to desktop, everything ok (even colors)
    Quote
    Havent done anything with PC but after like 1-2mins of idle in desktop; screen gives 1-2 secs blink of this:
    After that last pic the screen goes black it doesnt turn off or go to power saving mode, just stays on with nothing on it. Waited for 5-10 mins and when nothing happened I rebooted pc and same cycle goes around again.
    That windows is fresh format & install i made today and all i have installed on it are latest MSI drivers (chipset, real audio, lan) wich i downloaded today from global.msi.eu.
    I also tried to install latest nvidia drivers for that 7600 but it hangs on install just like mentioned above.
    ps. sry for posting pics instead of url's, but i think you get the whole picture easier this way.

  • MSI K9N SLI V2 nForce 570LT 64 Bit Driver Problems

    System Specs
    X2 4400+ 2.3ghz
    8800GT 512mb GPU
    250gb HD
    4x 1gb G-skill pc6400 DDR2 800
    MSI K9N SLI V2 nForce 570LT Socket AM2
    vx450w PSU
    Lite-on DVDRW LH-20A1S
    So I recently jumped ship from XP Home to Vista x64 to XP pro x64 and I am having issues updating my drivers I downloaded the MCP55_64_9.17_MW31006 at this site http://global.msi.com.tw/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=1415
    NVIDIA nForce 550/570/570/590 SLI System Drivers
    When I run the install though nothing happens Nvidia splash then nothing and the files are not recognized by the device manager.
    Any idea what the issue could be? sadly need the ethernet update so I can connect to the internet lol also the 2 discs have no effect neither work vista or the xp (tried vista since the x64 drives actually worked on it)

    Vista x64 ultimate. I wanted to try X64 XP but I ran into problems thus the original post ^-^
    Vista is nice I could live with it for Dx10 but man UAC sucks every attempt to disable = vista freak out and repair the file ^-^
    ATM I use XP Home with the DX10 crack (I own vista so I don't see a issue) but yet to install any games on it. I will load up and check it out   Still the fact I get medium with x8 aa is good imo. Game looks fantastic and with luck the FC2 engine won't be such a resource whore like crysis. I recall the Sandune (think thats the name) for FC1 even on low settings things still looked fantastic.

Maybe you are looking for