MSI K9N Ultra -Failed???

Hello. I have a problem. In my opinion, it is problem with my MB. I had a DVD-RW Samsung 203B (Sata). Problem: all DVD was closed (i use Nero 6,7,8 Ashampoo and i click Multisesion DVD and nothing), and DVD-RW detect as DVD-ROM. I change DVD, new is ASUS 2014L1T, I re-instal computers and it is same. DVD are closed and DVD-RW is detect as DVD-ROM. Where is a problem. I think, it is MB, but it is wrong Sata port (i change 5 port and nothing) or ....? Pls. I need help.
Thank

Quote from: BOSSKILLER on 26-January-08, 23:50:21
What Nero report about the drive?
Make sure that Nero is up to date.
"Drivers I find MSI site. "
Try with latest chipset drivers from Nvidia.
"Apacer DDR2 1GB 800MHz (3x)"
Use 2x memory sticks only.
Try with different SATA cable for the drive.
Hi.
I have a latest drivers.. I install new drivers from nVidia, from MSI for MB, i found new firmware for my DVD-RW (but is only 1.0)
I use 1,2 or 3 memory stick. I change a 3 cable. I have instaled Daemon tool Pro with one virtual disc. I install daemon later, as I had a problem with optical drive.
My info from Nero tools
sorry: pictures http://s266.photobucket.com/albums/ii264/samurayy/?action=view&current=Infotool.jpg

Similar Messages

MSI K9N Ultra (MS-7250 v2) SATA II ports dosnt work

I have problem with 4 of 6 SATA II ports in the mainboard (MSI K9N Ultra (MS-7250 v2)(SATA II 1~6 supports RAID 0/ 1/ 0+1 or RAID 5 mode by NVIDIA® nForce 570) doesn't work after install wrong program please help
thanks

why no any body help this pictures from my bois sitting and my problem I need help please
MSI K9N Ultra (MS-7250 v2)
bois pictures
Here is functioning normally
Here is functioning not normally

MSI K9N ULTRA 2F & PALIT 8800GT SONIC ISSUE

i have msi k9n ultra 2f and ati x1950gt. i decided to buy palit 8800gt sonic. but no monitor signal when i put palit 8800 gt sonic. everything works but no screen. then i replace my old card, working pc at the beginning. it says like this : " your bios settings overlock stopped to work. system back to previous settings. " like this.
palit 8800gt sonic changes my mobo's bios settings? there is any solution? i updated mobo's bios but still same problem. pls help me.

Well do >>Clear CMOS Guide<< with power cord removed,
and leave just one memory stick in 1st DIMM close to CPU socket, then try to boot.

MSI K9N ULTRA 2F max vdimm (max DDR2 voltage!)

1st: I would like to ask you, the maximum voltage for the vdimm, that MSI K9N ULTRA-2F provides.
2nd: Will it work with OCZ PC2-6400 EL DDR2 1GB (2X512MB) GOLD EDITION GX XTC ?
Greetings from Greece

Original 7250 supports 1.80 - 2.45v in 0.05v steps , latest bios is :7250v143
K9N ULTRA 2F is MS7250-040 and use another bios , latest : 7250v31
It supports DDR2-800 (PC2-6400) DDR2-667 & DDR2-533
The OCZ DDR2 PC2-6400 Gold GX XTC Rev 2 Dual Channel 2 GB nominal voltage is 1.95 volt
Latest bios for this board is
K9N Ultra (MS-7250) V3.1 BIOS Release
1. This is AMI BIOS release
2. This BIOS fixes the following problem of the previous version:
- Update AMD NPT version.
- Update SB module version.
- Support AMD AWAY mode.
Hard to say for sure if the VDIMM is the same (max 2.45v) since no manual is availible on any MSI location for
this K9N Ultra-2F version (only found it at Japan site ) . But it should be the same .

MOVED: MSI k9n ultra-2f voltage problem

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=121178.0

Quote from: BOSSKILLER on 01-November-08, 04:22:10
Look for extra vcore option in Cell Menu.
oO ok i see it , thanks

How to overclock my x2 3800+ with K9N Ultra

My current rig as below:-
AMD X2 3800+ AM2 stock fan
MSI K9N Ultra (MS-7250 v2.0 but on board stated v2.1) bios upgraded from 3.2 to 3.5
1G DDR2 667 Kingston Value Ram x 2
MSI 8600GT-Overclock edition
Lite-on 20X Sata DVD-Ram
Seagate Sata2 320GB
WD Pata 120GB
Cooler Master 500W Extreme
Cooler Master Centurion 5
As I'd seen in many forums that a lots of people are able to archieve 2.4G~2.6GB easily but I don't know why I can only able to archieve highest at 2.3G only.
My current setting is as below:-
Multiplier - 10
HT - 230
HTT - 5X
FSB - 287.5
Ram divider - 533
Clock speed at 2300mHz stock vcore & vdimm 1.95
But the moment I try to increase the HT to 240 or higher it tends to be unstable even I increase the vcore and vdimm.
Can someone advise me on this matter.

Quote from: BOSSKILLER on 10-May-07, 12:03:37
"Besides that I'd also tried to set HTT to 3x and loosen the ram timing to 5-5-5-15-20 2T. vcore at 1.45 vdimm 2.0 and HT set to 240 but it won't boot."
try with lesser steps. give CPU vcore only when need. what is your actual memory frequency at latest good OCed settings?
"Btw I'd not seen the function "DOT & aggressive memory timings" where am I suppose to disable it?"
aggressive memory timings option doesn't exist in your BIOS, DOT(Dynamic Overclocking) its Disabled by default, but ensure it.(located in Cell Menu).
"My PCI-E has set to 104Mhz. Coz I'd seen some forum advise to set to 104Mhz. So actually 103Mhz or 104Mhz will be more stable?"
nop will be the same.
provide screenshots from CPU-Z with your last good known OCed settings.
I'd set to disable on dynamic overclock all the time. btw I'd upload the link CPU-Z validation but I don't know how to put attachment thats why I upload the link.

Overclocking K9N Ultra

I've been reading around the overclocking forum trying to find some definative information on overclocking on the K9N Ultra (using latest bios) but can't really find anything. I know my way around the bios so if anyone could throw me some settings to change so I can get a decent speed . Spec in signiature
- David

i'll try to help you...
my rig:
AMD Athlon 64 X2 3800+ Windsor
MSI K9N Ultra BIOS ver 3.6
Corsair ValueSelect DDR2-PC 5300 2X512MB
MSI RX 1300PRO
Seagate 160GB SATA2 7200RPM
DVD-RW LG
HSF Scythe Infinity - Stock Fan
<yours is better than mine>
I OC from 2GHz to 2.8GHz <but, I prefer 2.7GHz, coz the temp. reach 67C on 2.8GHz>
BIOS setting:
go to Advanced Chipset Features -> MCP55 (SB) to AM2 (CPU) Freq. Auto DISABLED
go to Cell Menu -> Cool n Quiet DISABLED
CPU multiplier AUTO (10x)
vCore = test by yourself <different rig = different result>
CPU freq. / FSB freq. -> 270.00MHz <default 200.00MHz>
Memory setting = I'm not good at setting my memory
but, change vDIMM to 2.2V
Spread Spectum -> DISABLED ALL
any question??? ask me again....

K9N Ultra

i have a problem the system is shutdown and i don`t understanding why ?
MSI K9N Ultra-2F,
AM2 X2 Dual Core Processor 3800+ (default),
NVIDIA nFORCE 570 Chipset,
SuperTalent 2x1GB DDR2800 CL4 Dual Channel,
Asus EN7300GT TOP 128MB,
Samsung SATA2 160GB,
NEC ND4550A DVD+RW/-RW/16x,
NEC CD-RW NR-9500A,
PSU FORTRON ATX-300PNR /300W

Yes i tested it with a 400W power, but it is same. my mobo from affected series of nforce4 ultra (7250-040). it rarely resets itself. is it a solution to use single core cpu insted of dual core cpu? or must i RMA it to distributor for certain solution?
i have a mobo from affected series of nforce4 ultra.
it rarely resets itself. is it a solution to use single core cpu insted of dual core cpu? or must i RMA it to distributor for certain solution?
i have a mobo from affected series of nforce4 ultra (7250-040). it rarely resets itself. is it a solution to use single core cpu insted of dual core cpu? or must i RMA it to distributor for certain solution?
MSI K9N Ultra-2F,
AM2 X2 Dual Core Processor 3800+ (default),
NVIDIA nFORCE 570 Chipset,
SuperTalent 2x1GB DDR2800 CL4 Dual Channel,
Asus EN7300GT TOP 128MB,
Samsung SATA2 160GB,
NEC ND4550A DVD+RW/-RW/16x,
NEC CD-RW NR-9500A,
PSU FORTRON ATX-300PNR /300W

K9n ultra-2f strange behaviour with 250htt and more

Hi... My Pc:
Athlon 4200+ Windsor F2
MSI k9n ultra-2f , bios rev. 3.9
2x 1024 DDR2 Goodram 800mhz
Palit 8600 sonic+
Chieftec 420w
I have problem with overclocking more than 240htt... I turn spectrums off , and i set pci-e freq on 103. I also set processor multiplayer on 6 , mem on 400, and HT x2. The problem is that motherboard boot and works with 250 htt , even 300htt but... not always. It works good when i want to boot from shutted down pc, but when i try to change something in bios or reboot it from windows it's not working ( black screen , mobo doesnt boot ) ... I have to turn the pc off , and then turn it on again. Have you guy's some idea's about this problem ;/ ?
I tried with diffrent HT multiplayer's , i saw also that in CPU-Z , with 250-300fsb it shows HT x1 instead of x2-3 which is set in bios.

"The problem is that motherboard boot and works with 250 htt , even 300htt but... not always."
High HTT freq is not important. Go for max CPU freq. and keep HTT below 1000.
Leave CPU multi to Auto, drop HT link to x3, apply 667 memory index.
Then start rising CPU HT with small steps and re-test.

K9N Ultra-2F walls at 260FSB!

Hi,
I have recently bought Msi K9N Ultra-2F mobo. And my cpu is x2 3600 brisbane. I have a pair of kingston ddr2 667 ram.
A friend of mine also have this mobo too. But his processor is x2 4600. With his system i could do 290fsb by lowering the multiplier to 5x.
But my mobo can only do 260FSB. And it is not stable. Sometimes i can go into windows with this FSB but immediately my systems crashes and gave me Multi Bit ECC error( I have no idea with this error).
Now i am fully stable at 254FSB. But it is only 2.4ghz and this is too low for brisbane processors. I was expecting to go 300FSB+, when i was buying this mobo...
I have tried lots of things, but none of them worked. Now i need suggestions for increasing my FSB.
Regards,
ChivaricKnight.

Quote from: BOSSKILLER on 03-July-07, 05:55:34
have you disabled spectrums & setup pci-e freq. to 103Mhz?
provide screenshots from CPU-Z (main & memory pages)
also read Moan Guide and list full system spec.
Yes, i have disabled all spectrums. But set up pcie freq to 100mhz. Here is my cpu-z. I couldnt upload here correctly, sorry. I give the direct link:
http://img522.imageshack.us/my.php?image=adszds6.jpg
And my system specifications:
Msi K9n Ultra
X2 3600 brisbane
2x1gb kingston ddr2 667 value ram(hynix chip)
sapphire x1950gt vga
WD 320gb Hdd
Silverstone Strider 560W Psu

K9N Ultra-2F woes...

Hello,
I have a MSI K9N Ultra - 2F and for the moment an Athlon64 3500+ processor. Right know I am thinking of upgrading my CPU to a Athlon64x2. I did some research in the internet and all was well, until I found this post on your boards.
Needless to say that my m/b serial number is 601-7250-050XXXXXXXXXXXX!!!
The thing is that I bought this m/b 2 years ago. So, should I upgrade and if a problem occurs contact my local dealer (I bought this m/b from a computer store in Greece) or should I contact MSI directly if something goes wrong when I place the Athlon64x2 cpu?
Thanx in advance

Hello!
The problem occurs when moving large files around. https://forum-en.msi.com/index.php?topic=100766.0;wap2
If you should upgrade motherboard and processor, or just the processor, depends very much upon what you use the computer for.

K9N Ultra-2F no display after shutdown

Type:K9N Ultra-2F V2.2 ERP:110
BIOS version:7250v3.6
External VGA Type:MSI NX8600GT
CPU Type:ATHLON64 X2 5000+ ADA5000IAA5CS
Memory Type:2X 1GB CORSSAIR
Power Supply Type:THERMALTAKE 400W
And here is the problem: At first turn on(after clear cmos) it was can display normally,I can set the BIOS configuration,then Save&Exit,and display again.But after I shutdown manually with short the PWSW pin,then I turn on it was can't display.It was can display again if clear cmos before turn on.There is any problem with that hardware configuration? or need to update the BIOS?
Best Regards,
Nurman

take a screen shot of CPU-Z with both cpu and memory screens with fail safe defaults loaded, and then with optimized defaults and post them here( you may have to use a hosting site)
if that is 20amps on one rail only I beleive your PSU is not strong enough for your setup. what is the model # that TT400w psu?
Henry

Overclocking the MSI KT3 Ultra ARU

Hey,
I read some reviews with the kt3 Ultra ARU and i have read that people have been getting the FSB up to around 167? Yet, i fail to get it past 151? Any suggestions?
-Knowa-
MSI KT3 Ultra ARU
AMD xp 1800+
768 mb pc2100
TDK 40x12x48
Lite ON DVD
ATI Radeon 8500 (GIGABYTE)

you would have more chance of it booting at 166
than 151 as the divider kicks in at 152
at 166 fsb your video and pci slots are at the correct speed
it can be done if you have been lucky with the cpu you gotlink

Monitor doesnt wake up when booting first time, have to restart - k9n ultra-2f

So, I have few problems. The main problem is in da topic:
I bought an used computer about two weeks ago. I installed windows and all drivers etc.
With the old bios (cant remember what version) all was okay except always in boot an error message was shown that said something that the proseccor could not be recognised but the processor was still shown right in My Computer.. :s
Because of that error message i decided to update bios. I updated it throught live update 3 to v.3.6 and now i dont get the processor error message but the monitor doesnt wake up in the boot.. I have to press reset button and then when the monitor wakes up there comes an error message what says something like "Warning!!! The previous performance of overclocking is failed, and the system is restored to the defauls settings". Then I press any key and windows boots normally.
I reupdated v.3.6 bios today manually from floppydisk but the problem didnt go anywhere.
I have searched this forum but cant find same kind of problem posted.
Can somebody please help me with this and tell what could be the problem?
Also when booting second time so that the monitor wakes up, i get four alert sounds.. What could those mean?
My computer is pretty powerful (amd athlon 64 5600+ x2, club3d gf 7950gt, 2gb 533mhz..) It should be very smooth and fast but it often appears slowliness and ..how can i say it.. temporary tilting? :p And the 3dmark03 benchmark gives me 19465 points, it should be giving much more. The computer is clean, no viruses or adware. What could cause this?
Sorry for the messy message and bad english and im not really good at computers

Thanks for the reply.
I didnt have this issue before updating BIOS..
And i didnt find jbat1 from my k9n ultra-2f. I didnt even find it from the mb manual. Theres only a Clear CMOS Button: SW2. I pushed it few times and then i rebooted my computer. At the first time the monitor woke up instantly and i was like wohooooo but then i shut down the computer and booted it again.. The monitor didnt wake up before pressing the reset button, the same problem was back.
I think that the SW2 button reset the bios settings like the jbat1 would do, because i had disabled the big logo at the boot and after pressing SW2 the logo was back.
Then i set the memory vcore to 2.0V but it didnt help. Infact i think the computer had come a bit more slowly.. :s I think it may be the RAM what makes my comp so slow... dunno.

Random reboots /w MSI 745 Ultra

Hi,
I'm having some stability issues with my system, specs are as follows:
XP 2000+ (Boxed fan)
MSI 745 Ultra
512 Mb PC2700 (1 module, generic labeled setec)
MSI GF4 Ti4200 64 Mb
IBM Deskstar 60GXP 40 Gb
Aopen ATX H500A/MT, 300W
Windows XP Pro
I've upgraded to the latest bios, updated to all latest driver versions and fiddled with various settings, but nothing seems to keep the system stable in the long run. I've had these reboots even while browsing the web with a minimal system load. CPU temp ranges from 48-55 deg. C and case temp is about 35, which I reckon to be pretty normal (no o/c). With the memory set to 333 MHz the system copes really bad (e.g. fails to run a 3dMark2001 run), but when I turn the memory to 266 the reboots are far less frequent (sometimes many hours in between).
I concluded that my problems were linked to the memory so I had the module changed (same generic, tho), but this hasn't really helped. Would it help to switch in brand memory like apacer or kingston? Any ideas and suggestions are welcome...

Alrighty!
The problem is now solved. It turned out to be both memory and psu related. After exchanging the generic mod for an apacer the system actually worked at 4:3 mem/fsb, but the random boots kept coming every few hours. This convinced me that the psu was the main culprit. After installing a q-tec 450w in the case the system has been rock solid even at a slight o/c (138 fsb). The dual fan structure of the psu has actually made my cpu and chassis temps drop a few degrees, even though I already had a case fan at the back.
Anyways, thanks once again for the advice!
~J

MSI K9N Ultra -Failed???

Similar Messages

Maybe you are looking for