MSI K9N Ultra (MS-7250 v2) SATA II ports dosnt work

I have problem with 4 of 6  SATA II ports in the mainboard  (MSI K9N Ultra (MS-7250 v2)(SATA II 1~6 supports RAID 0/ 1/ 0+1 or RAID 5 mode by NVIDIA® nForce 570) doesn't work after install wrong program please help
thanks

why no any body help this pictures from my bois sitting and my problem I need help please
 MSI K9N Ultra (MS-7250 v2)
bois pictures
Here is functioning normally
Here is functioning not normally

Similar Messages

  • MSI K9N ULTRA 2F max vdimm (max DDR2 voltage!)

    1st:   I would like to ask you, the maximum voltage for the vdimm, that MSI K9N ULTRA-2F provides.
    2nd:  Will it work with OCZ PC2-6400 EL DDR2 1GB (2X512MB) GOLD EDITION GX XTC ?
    Greetings from Greece 

    Original 7250 supports 1.80 - 2.45v in 0.05v steps , latest bios is :7250v143
    K9N ULTRA 2F is MS7250-040 and use another bios , latest : 7250v31
    It supports DDR2-800 (PC2-6400) DDR2-667 & DDR2-533
    The OCZ DDR2 PC2-6400 Gold GX XTC Rev 2 Dual Channel 2 GB nominal voltage is 1.95 volt
    Latest bios for this board is
    K9N Ultra (MS-7250) V3.1 BIOS Release
    1. This is AMI BIOS release
    2. This BIOS fixes the following problem of the previous version:
    -  Update AMD NPT version.
    -  Update SB module version.
    -  Support AMD AWAY mode.
    Hard to say for sure if the VDIMM is the same (max 2.45v) since no manual is availible on any MSI location for
    this K9N Ultra-2F version (only found it at Japan site ) . But it should be the same .

  • MSI K9N ULTRA 2F & PALIT 8800GT SONIC ISSUE

    i have msi k9n ultra 2f and ati x1950gt. i decided to buy palit 8800gt sonic. but no monitor signal when i put palit 8800 gt sonic. everything works but no screen. then i replace my old card, working pc at the beginning. it says like this : " your bios settings overlock stopped to work. system back to previous settings. " like this.
    palit 8800gt sonic changes my mobo's bios settings? there is any solution?  i updated mobo's bios but still same problem. pls help me.

    Well do >>Clear CMOS Guide<< with power cord removed,
    and leave just one memory stick in 1st DIMM close to CPU socket, then try to boot.

  • MSI K9N Ultra -Failed???

    Hello. I have a problem. In my opinion, it is problem with my MB. I had a DVD-RW Samsung 203B (Sata). Problem: all DVD was closed (i use Nero 6,7,8 Ashampoo and i click Multisesion DVD and nothing), and DVD-RW detect as DVD-ROM. I change DVD, new is ASUS 2014L1T, I re-instal computers and it is same. DVD are closed and DVD-RW is detect as DVD-ROM. Where is a problem. I think, it is MB, but it is wrong Sata port (i change 5 port and nothing) or ....? Pls. I need help.
    Thank

    Quote from: BOSSKILLER on 26-January-08, 23:50:21
    What Nero report about the drive?
    Make sure that Nero is up to date.
    "Drivers I find MSI site. "
    Try with latest chipset drivers from Nvidia.
    "Apacer DDR2 1GB 800MHz  (3x)"
    Use 2x memory sticks only.
    Try with different SATA cable for the drive.
    Hi.
    I have a latest drivers.. I install new drivers from nVidia, from MSI for MB, i found new firmware for my DVD-RW (but is only 1.0)
    I use 1,2 or 3 memory stick. I change a 3 cable. I have instaled Daemon tool Pro with one virtual disc. I install daemon later, as I had a problem with optical drive.
    My info from Nero tools
    sorry: pictures http://s266.photobucket.com/albums/ii264/samurayy/?action=view&current=Infotool.jpg

  • MOVED: MSI k9n ultra-2f voltage problem

    This topic has been moved to Overclockers & Modding Corner.
    https://forum-en.msi.com/index.php?topic=121178.0

    Quote from: BOSSKILLER on 01-November-08, 04:22:10
    Look for extra vcore option in Cell Menu.
    oO ok i see it , thanks

  • How to overclock my x2 3800+ with K9N Ultra

    My current rig as below:-
    AMD X2 3800+ AM2 stock fan
    MSI K9N Ultra (MS-7250 v2.0 but on board stated v2.1) bios upgraded from 3.2 to 3.5
    1G DDR2 667 Kingston Value Ram x 2
    MSI 8600GT-Overclock edition
    Lite-on 20X Sata DVD-Ram
    Seagate Sata2 320GB
    WD Pata 120GB
    Cooler Master 500W Extreme
    Cooler Master Centurion 5
    As I'd seen in many forums that a lots of people are able to archieve 2.4G~2.6GB easily but I don't know why I can only able to archieve highest at 2.3G only.
    My current setting is as below:-
    Multiplier - 10
    HT - 230
    HTT - 5X
    FSB - 287.5
    Ram divider - 533
    Clock speed at 2300mHz stock vcore & vdimm 1.95
    But the moment I try to increase the HT to 240 or higher it tends to be unstable even I increase the vcore and vdimm.
    Can someone advise me on this matter.

    Quote from: BOSSKILLER on 10-May-07, 12:03:37
    "Besides that I'd also tried to set HTT to 3x and loosen the ram timing to 5-5-5-15-20 2T. vcore at 1.45 vdimm 2.0 and HT set to 240 but it won't boot."
    try with lesser steps. give CPU vcore only when need. what is your actual memory frequency at latest good OCed settings?
    "Btw I'd not seen the function "DOT & aggressive memory timings" where am I suppose to disable it?"
    aggressive memory timings option doesn't exist in your BIOS, DOT(Dynamic Overclocking) its Disabled by default, but ensure it.(located in Cell Menu).
    "My PCI-E has set to 104Mhz. Coz I'd seen some forum advise to set to 104Mhz. So actually 103Mhz or 104Mhz will be more stable?"
    nop will be the same.
    provide screenshots from CPU-Z with your last good known OCed settings.
    I'd set to disable on dynamic overclock all the time. btw I'd upload the link CPU-Z validation but I don't know how to put attachment thats why I upload the link.

  • Msi k9n with 2 sata disc in strip and a plextor sata burner connected

    can all msi k9n motherboards run with 2 sata disc in astripe and a plextor sata dvd burner connected to the sata connectors ?
    I think on following msi boards :
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=730
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=729
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=731

    A onboard satacontroller until now controls a pair of sata ports on NF4 and older.
    So with 4 ports native , there is two controllers aka' you enable raid pr. controller as in sata1/2 , sata 3/4 .
    NF570 looks different from NF4 (atleast in the MSI K9N bios) in that way that you can include pr port eg.
    SATA0 Primary =Raid Enabled - SATA0 Secondary=Raid Enabled - SATA1 Primary=Raid Enabled - SATA1 Secondary=Disabled , and so on .
    Why must you absolutely have sata burner , it's nothing gained over a IDE type in the matter of speed .
    Even 16X DVD doesn't utilize 33MB/s that Ultra DMA2 is currently at for IDE burners .
    16X DVD utilize 21MB/s , 54X CDR utilize 8MB/s , so no one needs burners at a sata controller.
    But anyway , a silicon Image or a Promise PCI controller board should work  .
    CDR / DVDR read&write speed:

  • K9N Ultra

    i have a problem the system is shutdown  and i don`t understanding why ?
    MSI K9N Ultra-2F,
    AM2 X2 Dual Core Processor 3800+ (default),
    NVIDIA nFORCE 570 Chipset,
    SuperTalent 2x1GB DDR2800 CL4 Dual Channel,
    Asus EN7300GT TOP 128MB,
    Samsung SATA2 160GB,
    NEC ND4550A DVD+RW/-RW/16x,
    NEC CD-RW NR-9500A,
    PSU FORTRON ATX-300PNR /300W

    Yes i tested it with a 400W power, but it is same.  my mobo from affected series of nforce4 ultra (7250-040). it rarely resets itself. is it a solution to use single core cpu insted of dual core cpu? or must i RMA it to distributor for certain solution?
    i have a mobo from affected series of nforce4 ultra.
    it rarely resets itself. is it a solution to use single core cpu insted of dual core cpu? or must i RMA it to distributor for certain solution?
    i have a mobo from affected series of nforce4 ultra (7250-040). it rarely resets itself. is it a solution to use single core cpu insted of dual core cpu? or must i RMA it to distributor for certain solution?
    MSI K9N Ultra-2F,
    AM2 X2 Dual Core Processor 3800+ (default),
    NVIDIA nFORCE 570 Chipset,
    SuperTalent 2x1GB DDR2800 CL4 Dual Channel,
    Asus EN7300GT TOP 128MB,
    Samsung SATA2 160GB,
    NEC ND4550A DVD+RW/-RW/16x,
    NEC CD-RW NR-9500A,
    PSU FORTRON ATX-300PNR /300W

  • K9N Ultra-2F woes...

    Hello,
    I have a MSI K9N Ultra - 2F and for the moment an Athlon64 3500+ processor. Right know I am thinking of upgrading my CPU to a Athlon64x2. I did some research in the internet and all was well, until I found this post on your boards.
    Needless to say that my m/b serial number is 601-7250-050XXXXXXXXXXXX!!!
    The thing is that I bought this m/b 2 years ago. So, should I upgrade and if a problem occurs contact my local dealer (I bought this m/b from a computer store in Greece) or should I contact MSI directly if something goes wrong when I place the Athlon64x2 cpu?
    Thanx in advance

    Hello!
    The problem occurs when moving large files around. https://forum-en.msi.com/index.php?topic=100766.0;wap2
    If you should upgrade motherboard and processor, or just the processor, depends very much upon what you use the computer for.

  • Overclocking K9N Ultra

    I've been reading around the overclocking forum trying to find some definative information on overclocking on the K9N Ultra (using latest bios) but can't really find anything. I know my way around the bios  so if anyone could throw me some settings to change so I can get a decent speed . Spec in signiature
    - David

    i'll try to help you...
    my rig:
    AMD Athlon 64 X2 3800+ Windsor
    MSI K9N Ultra BIOS ver 3.6
    Corsair ValueSelect DDR2-PC 5300 2X512MB
    MSI RX 1300PRO
    Seagate 160GB SATA2 7200RPM
    DVD-RW LG
    HSF Scythe Infinity - Stock Fan
    <yours is better than mine>
    I OC from 2GHz to 2.8GHz <but, I prefer 2.7GHz, coz the temp. reach 67C on 2.8GHz>
    BIOS setting:
    go to Advanced Chipset Features -> MCP55 (SB) to AM2 (CPU) Freq. Auto DISABLED
    go to Cell Menu -> Cool n Quiet DISABLED
    CPU multiplier AUTO (10x)
    vCore = test by yourself <different rig = different result>
    CPU freq. / FSB freq. -> 270.00MHz <default 200.00MHz>
    Memory setting = I'm not good at setting my memory
    but, change vDIMM to 2.2V
    Spread Spectum -> DISABLED ALL
    any question??? ask me again....

  • K9n ultra-2f strange behaviour with 250htt and more

    Hi... My Pc:
    Athlon 4200+ Windsor F2
    MSI k9n ultra-2f , bios rev. 3.9
    2x 1024 DDR2 Goodram 800mhz
    Palit 8600 sonic+
    Chieftec 420w
    I have problem with overclocking more than 240htt... I turn spectrums off , and i set pci-e freq on 103. I also set processor multiplayer on 6 , mem on 400, and HT x2. The problem is that motherboard boot and works with 250 htt , even 300htt but... not always. It works good when i want to boot from shutted down pc, but when i try to change something in bios or reboot it from windows it's not working ( black screen , mobo doesnt boot ) ... I have to turn the pc off , and then turn it on again. Have you guy's some idea's about this problem ;/ ?
    I tried with diffrent HT multiplayer's , i saw also that in CPU-Z , with 250-300fsb it shows HT x1 instead of x2-3 which is set in bios.

    "The problem is that motherboard boot and works with 250 htt , even 300htt but... not always."
    High HTT freq is not important. Go for max CPU freq. and keep HTT below 1000.
    Leave CPU multi to Auto, drop HT link to x3, apply 667 memory index.
    Then start rising CPU HT with small steps and re-test.

  • K9N Ultra-2F walls at 260FSB!

    Hi,
    I have recently bought Msi K9N Ultra-2F mobo. And my cpu is x2 3600 brisbane. I have a pair of kingston ddr2 667 ram.
    A friend of mine also have this mobo too. But his processor is x2 4600. With his system i could do 290fsb by lowering the multiplier to 5x.
    But my mobo can only do 260FSB. And it is not stable. Sometimes i can go into windows with this FSB but immediately my systems crashes and gave me Multi Bit ECC error( I have no idea with this error).
    Now i am fully stable at 254FSB. But it is only 2.4ghz and this is too low for brisbane processors. I was expecting to go 300FSB+, when i was buying this mobo...
    I have tried lots of things, but none of them worked. Now i need suggestions for increasing my FSB.
    Regards,
    ChivaricKnight.

    Quote from: BOSSKILLER on 03-July-07, 05:55:34
    have you disabled spectrums & setup pci-e freq. to 103Mhz?
    provide screenshots from CPU-Z (main & memory pages)
    also read Moan Guide and list full system spec.
    Yes, i have disabled all spectrums. But set up pcie freq to 100mhz. Here is my cpu-z. I couldnt upload here correctly, sorry. I give the direct link:
    http://img522.imageshack.us/my.php?image=adszds6.jpg
    And my system specifications:
    Msi K9n Ultra
    X2 3600 brisbane
    2x1gb kingston ddr2 667 value ram(hynix chip)
    sapphire x1950gt vga
    WD 320gb Hdd
    Silverstone Strider 560W Psu

  • MSI 745 Ultra multiple gfx cards

    I have an MSI 745 Ultra , BIOS v1.4 and two gfx cards. One PCI and one AGP. On boot the AGP cards is initialized and used. Is there a way to initialize the PCI card first ?
    Other motherboards have a BIOS option to select between a PCI or AGP card to be initialized first, but my BIOS has no such option ( or at least I could not find it ).
    regards,
    stein
    I have an MSI 745 Ultra, Athlon 900 ( 100 MHz FSB ) and 256 PC266 DDR memory module ( the chips are made by MOSEL (http://www.moselvitelic.com), chip type is V58C2128804SAT7 ).
    BIOS is v1.4 ( v1.5 has the same problem )
    The memory only runs at 200 MHz.
    If I try to set it at 266 MHz ( CPU:MEM ratio 3:4 , FSB is 100 MHz ) then the computer keeps on rebooting, not even the VGA BIOS screen is visible. The only way back is clearing the CMOS with the jumper. ( not even holding "Insert" works. Is that supported at all ? On my older MB , MSI K7T Pro2A holding "Insert" on bootup, would use default BIOS settings, but still leave the CMOS intact, so you could switch back certain settings if the prevent from booting )
    Any suggestions ?
    I tried BIOS v1.3 and there it works !
    regards,
    stein
    I have an MSI 745 Ultra.
    Power-on by keyboard does not work.
    help.
    the keyboard is Cherry G-83 ( PS/2 )
    I tried BIOS v1.3 , 1.4 and 1.5.
    regards,
    stein
    >

    Yes, but now the subject is a lot less descriptive.
    With the original post, forum users could see what my problem is just by looking at the message list.
    Now only those who open my message can see what problems I have. By this I lost a lot of potential helpers.
    I personally would probably not open a message with such unspecific title as "MSI 745 Ultra problems"
    I'll try to change the subject ...
    regards,
    stein

  • Sata Raid problems with MSI KT4 Ultra Via kt400 chipset

    ok i am having major problems setting up my sata raid in my brothers msi KT4 Ultra via KT 400 chipset
    it comes up with my irq settings are wrong
    my hard drives are WD 120 GB 7200rpms SATA - sold my mobo asus A7N8X - Delux and used my bros mobo above but just cant get them to work if ne one has ne idea on how to fix it (bios is still factory default do i have too flash it to get it too work etc)
    would help lots thanx

    you dont need multiple threads on the same thing

  • MSI K9N SLI SATA problem

    i have just board the MSI K9N SLI and a AMD X2 6000+ processor.
    i have a ATA harddisk with my system on and a SATA harddisk, BUT i can't see my SATA.
    i can see it i the Bios and at the "remove safely icon" BUT nowhere else!!
    enyone now WHY, i have a lot of programes on that HD that i need.
    Hope you can help, fast.

    read Moan Guide
    ensure that RAID is disabled for SATA channels from BIOS.
    from Windows, type in "run": diskmgmt.msc and check the drive status.

Maybe you are looking for