Msi K9N2 Platinum SLI and Windows Server 2003 r2 32 bit edition

Does anyone know or have tried to get this board to work on server 2003 32 bit edition. I seem to get past the raid part but the realtek 8211bl and audio are giving me fits. Any links to good drivers would be appreciated.
Spec of system:
Amd 9950 Quad
4 gig memory
Msi K9N2 Platinum SLI
2 500 gig sata

Ok overall solution this board works awesome with Windows Server 2003 Enterprise R2 with Sp 2.
Here are a few tricks for the Co processor controller, Sm Bus, Audio and finally the networking controller.
When you finally get windows loaded. Make sure you put Service Pack 2 or 3 on before u install drivers.
The raid drivers are simple for the 32 bit version use the xp ones and load both raid drivers during setup. Requires 2 floppys or Slipstream disk.
http://global.msi.com.tw/index.php?func=driverfile&dno=7067&i=2
Once you get windows loaded and Sp 2 or better on. Stick in your windows vista driver disk in. Once there do not install anything.
Goto device manager and update drivers on all that are with the yellow ? excpet the networking drivers and just do an automatic search and boom your done. It will also ask you if you want to enable your audio at this time. Do so but do not reboot untill u finish installing all drivers but networking. Than reboot pc
Last part is for networking card. We need you to be in safe mode for this. So once u install all drivers and start reboot hit F8 and goto safe mode. Once in safe mode take out vista driver disk and put in xp driver disk. Goto device manager and update driver on network controller and let it do an automatic search and it will installl it. It will say it needs to be rebooted to work. Go ahead and reboot and your networking card will work.
Probably simpliar solution. But just wanted to give my help.

Similar Messages

Which VMware support Windows 7 as Host and Windows Server 2003 as Guest OS

Folks,
Hello. I need to install PeopleSoft PIA in Windows Server 2003.
Because my laptop is preinstalled Windows 7 Home Premium Editon and cannot dual boot multiple Operating systems. I have to install VMware in Host Windows 7 and then install Windows Server 2003 as Guest OS for PIA.
I have installed VMware Server 2.0.2 into Host Windows 7 and Windows Server 2003 as Guest OS. Everything works fine for a while. But VMware Server Home Page https://mylaptop:8333/ui cannot display any more.
I have found that Windows 7 is not a supported Host Operating System for VMware Server 2 and strange thing might happen anytime. I found that "VMware Player 3" is fully supported Windows 7 as Host OS but is not supported Windows Server 2003 as Guest OS.
Does any folks know which VMware product support Windows 7 as Host OS and Windows Server 2003 as Guest OS ?
Many thanks in advance.

Hi,
Based on my research, I would like to suggest the following:
1.
Ensure the printer is compatible with Windows 7 and Windows Server 2003 and the drivers are up-to-date.
2.
Try the following method:
Printers that use ports that do not begin with COM, LPT,
or USB are not redirected in a remote desktop or a terminal services session
Hope this helps. Thanks.
Regards,
Nicholas Li - MSFT
That doesn't apply to Windows 7 Machines. I'm having the same problem as Acer_, I have a RDP Session from a Windows 7 Machine to a Windows XP machine and the local printer was available a few days ago but isn't anymore. The drivers are installed on both PC's
and are compatible with Windows 7.

IPhone 3G - updated to v3.0 - iTunes 8.2 and Windows server 2003 problems!

Argh! I just lost an ability to sync my iphone with my Windows laptop/Outlook running Windows Server 2003.
Everything worked fine until I upgraded iPhone 3G to version 3.0
That forced me to iTunes version 8.2 update.
The AppleMobileDeviceSupport.msi which comes with the latest version of iTunes requires Windows XP SP2 or newer and installation fails.
Is there any workaround available?

Hello
I'm having the same problem! Did you find a way to work around it?

Audigy 2 Platinum EX and Windows Server 2

Just upgraded from Windows SBS 2003 to Windows Server 2003. My Audigy 2 Platinum EX seems to be working properly, but my microphone now only pops and crackles. I did not have this problem on SBS 2003. I am running Server 2003 SP and have the latest drivers for the sound card. Please assist with this issue.

/ Came up with something of a partial fix for this.
Right click the driver installation file, go to properties, find the compatibility bit and change it to XP, then install.
Most things stayed not working, but the one I really need "Line in 2/Mic 2" now works, thankfully.
Be nice to get all the functionality back though!

Flex and Windows Server 2003 and MSSQL

Hi everyone,
I tried to connect to MSSQL using PHP. I did not get any
error message but the only problem is when I try to test the
problem, I get this error message. Everything works fine on my
local computer "developer", but when I try to program and test on
my Windows Server 2003, I get this error message:
ReferenceError: Error #1069: Property loginsuccess not found
on String and there is no default value.
at index/::checkLogin()
at index/__login_user_result()
at
flash.events::EventDispatcher/flash.events:EventDispatcher::dispatchEventFunction()
at flash.events::EventDispatcher/dispatchEvent()
at mx.rpc.http.mxml::HTTPService/
http://www.adobe.com/2006/flex/mx/internal::dispatchRpcEvent()
at mx.rpc::AbstractInvoker/
http://www.adobe.com/2006/flex/mx/internal::resultHandler()
at mx.rpc::Responder/result()
at mx.rpc::AsyncRequest/acknowledge()
at ::DirectHTTPMessageResponder/completeHandler()
at
flash.events::EventDispatcher/flash.events:EventDispatcher::dispatchEventFunction()
Can someone please help me, I really need to figure this out
for my company.

a string value is being read checkLogin() when its expecting
an object with property loginsuccess.
maybe its a typo or something in your code.
for example you may have place:
var.loginsuccess == "loginsuccess";
in which it should be:
var == "loginsuccess";

Tiger 10.4.4 or 5 and Windows Server 2003 Services For Macintosh unstable??

We are running these tested Mac clients here:
macMini 1.5Ghz 10.4.5
G4 Quicksilver 800Mhz 10.4.4
G4 Dual Mirror PowerMac 10.4.4
They mount volumes on these servers:
Dell Windows Server 2000 (SFM)
Dell Windows Server 2003 (SFM)
Xserve G4 OS 10.3.9 Server
Macs sleep settings are this:
Computer sleep=1 hour
Display sleep=1 hour
Hard drive=sleep
Symptom:
When the Mac goes to sleep, the 2 Windows Mac File servers volumes are
disconnected. Upon wake, the error message stating they were disconnected are waiting.
The Xserve volume is untouched. This should not be a problem
since the Windows servers are running Appletalk via IP not
native Appletalk protocol.
Comments:
Might be related to the lookupd bug in Tiger? http://www.macintouch.com/readerreports/macosx1042/topic3108.html
Here’s the system log from the macMini: (13:47 is when I woke it and manually mounted the volumes)
Feb 23 09:37:22 M00XXX /System/Library/Frameworks/ApplicationServices.framework/Frameworks/ATS.framewo rk/Support/ATSServer: ***********************************
Feb 23 13:14:13 M00XXX kernel[0]: AFPSleepWakeHandler: going to sleep
Feb 23 13:14:13 M00XXX kernel[0]: AFP_TCP ASP_TCP SendSleepPkt: sending regular sleep
Feb 23 13:14:13 M00XXX kernel[0]: AFP_TCP ASP_TCP SendSleepPkt: sending regular sleep
Feb 23 13:14:24 M00XXX configd[32]: AppleTalk shutdown
Feb 23 13:14:25 M00XXX configd[32]: AppleTalk shutdown complete
Feb 23 13:14:28 M00XXX launchd: Server 0 in bootstrap 1103 uid 0: "/usr/sbin/lookupd"[88]: exited abnormally: Hangup
Feb 23 13:14:28 M00XXX configd[32]: posting notification com.apple.system.config.network_change
Feb 23 13:47:06 M00XXX kernel[0]: System Sleep
Feb 23 13:47:06 M00XXX kernel[0]: System Wake
Feb 23 13:47:06 M00XXX kernel[0]: Wake event 0020
Feb 23 13:47:08 M00XXX kernel[0]: UniNEnet::monitorLinkStatus - Link is up at 100 Mbps - Full Duplex
Feb 23 13:47:08 M00XXX kernel[0]: USB caused wake event (OHCI)
Feb 23 13:47:08 M00XXX configd[32]: setting hostname to "M00XXX.local"
Feb 23 13:47:08 M00XXX configd[32]: AppleTalk startup
Feb 23 13:47:10 M00XXX kernel[0]: AFPSleepWakeHandler: waking up
Feb 23 13:47:11 M00XXX configd[32]: AppleTalk startup complete
Feb 23 13:47:12 M00XXX configd[32]: posting notification com.apple.system.config.network_change
Feb 23 13:47:12 M00XXX lookupd[7515]: lookupd (version 369.2) starting - Thu Feb 23 13:47:12 2006
Feb 23 13:47:12 M00XXX configd[32]: setting hostname to "m00xxx.secret.com"
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_Reconnect: Invalid reconn token length 0 /Volumes/VOL1
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_Reconnect: AFP Version 4 does not support reconnect /Volumes/VOL1
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_Reconnect: Reconnect not allowed /Volumes/VOL1
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_Reconnect: posting to KEA to unmount /Volumes/VOL1
Feb 23 13:47:13 M00XXX KernelEventAgent[39]: tid 00000000 received VQ_DEAD event (32)
Feb 23 13:47:13 M00XXX KernelEventAgent[39]: tid 00000000 type 'afpfs', mounted on '/Volumes/VOL1', from 'afp_3Xs1VX4aumPi3flxDN2GLoYD-1.2c000009', dead
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_unmount: /Volumes/VOL1, flags 524288, pid 39
Feb 23 13:47:13 M00XXX KernelEventAgent[39]: tid 00000000 type 'afpfs', mounted on '/Volumes/VOL2', from 'afp_3Xs1VX4aumPi3flxDN2GLoYD-2.2c00000a', dead
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_unmount: /Volumes/VOL2, flags 524288, pid 39
Feb 23 13:47:13 M00XXX KernelEventAgent[39]: tid 00000000 found 2 filesystem(s) with problem(s)
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_Reconnect: Invalid reconn token length 0 /Volumes/Asura_Queues
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_Reconnect: AFP Version 4 does not support reconnect /Volumes/Asura_Queues
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_Reconnect: Reconnect not allowed /Volumes/Asura_Queues
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_Reconnect: posting to KEA to unmount /Volumes/Asura_Queues
Feb 23 13:47:13 M00XXX kernel[0]: AFP_VFS afpfs_unmount: /Volumes/Asura_Queues, flags 524288, pid 39
Feb 23 13:47:13 M00XXX KernelEventAgent[39]: tid 00000000 type 'afpfs', mounted on '/Volumes/Asura_Queues', from 'afp_3QgJ7Z2s2fVR2flF2I2ZlbNQ-1.2c00000b', dead
Feb 23 13:47:13 M00XXX KernelEventAgent[39]: tid 00000000 received unknown event (48)
Feb 23 13:49:54 M00XXX kernel[0]: AFP_VFS afpfs_mount: /Volumes/Asura_Queues, pid 7519
Feb 23 13:50:13 M00XXX kernel[0]: AFP_VFS afpfs_mount: /Volumes/VOL1, pid 7520
Feb 23 13:50:13 M00XXX kernel[0]: AFP_VFS afpfs_mount: /Volumes/VOL2, pid 7520

My SMB share get disconnected while my Powerbook was still running.
Errors in system.log:
May 8 23:08:13 snoopy KernelEventAgent[46]: tid 00000000 received VQ_DEAD event (32)
May 8 23:08:13 snoopy KernelEventAgent[46]: tid 00000000 type 'smbfs', mounted on '/Volumes/backup', from '//HALO;CYONG@PEANUTS/BACKUP', dead
May 8 23:08:13 snoopy KernelEventAgent[46]: tid 00000000 found 1 filesystem(s) with problem(s)
Anyone else having the same problem?

Crystal Reports 9 and Windows Server 2003 sp1/sp2

Post Author: jnribeyrol
CA Forum: General
Hello,
due to security updates in my company, we have to upgrade from Windows Server 2003 to sp1 or sp2.
I haven't been able in the support to find out if there was any problem with Report Access Server on these SPs.
Can somebody help me.
regards

CR XI is past it's end of life. You can upgrade to CR XI R2 for free.
Go to: http://www.sdn.sap.com/irj/boc and download the trial version of CR XI R2 and use your XI keycode, then apply the patches which you can get to by clicking on the BusinessObjects tab above, then Downloads.
Typically this is due to DEP, search forums for more info on how to configure it as well as your Anti-virus and/or Firewall may be stopping CR from running. You also need full Admin rights to install all components.
Thank you
Don

Acrobat 8 Professional and Windows Server 2003 R2 Issue

Hi
Our customers using Adobe Acrobat 8 Professional on Windows server 2003 R2 SP2. It works some period of time but then application stops working with this error and cannot start anymore:
Faulting application Acrobat.exe, version 8.1.0.137, faulting module Checkers.api, version 8.1.0.137, fault address 0x000021a2.
What can be the problem? There is nothing in the knowledgebase.
Regards,
Jelena

Hello jordixip,
You can connect your Mac to Terminal Services using Remote Desktop Connection Client . You need a license, the client software, and turning on the appropriate bits on the server. It is in Micro$oft-ese, but the overview is here.
Good Luck!
Zubin
iMac G4 Mac OS X (10.3.9) Mac OS 9.2 & earlier, Win2k Pro & Server

Officejet 8600 Pro and Windows Server 2003 (32 bit)

The company I am consulting for purchased three 8600 Pro printers to replace three older and non-working printers. They are still using XP Pro on their workstations and running Windows Server 2003 (32 bit version) on a file server and data server. All of the workstations have the drivers for the 8600 installed and are printing with no problems through the network. I checked the driver page on HP's site and there are no drivers listed for the 32 bit version of the server OS, only the 64 bit version. I need to install the printer drivers on these servers to be able to print reports without having to purchase another printer. Has anyone found a workaround to this problem or do I have to install one of the older printers in order to print and fax from the servers? I really can't shut down these servers in order to reinstall the 64 bit version of the OS.

Hi,
Install the software using the command prompt, the software do supported on Windows Server 2003 but its installation process is different.
Follow these steps to install the printer on the server:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c03351547&lc=en&product=4323659&tmp...
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

PSUS4 and Windows 7 and Windows XP and Windows Server 2003

I have a small domain network with Windows Server 2003 , Windows 7 desktop, Windows XP desktop. I have an HP LaserJet P3005 printer. I need to be able to print to the HP printer from all of the computers (server, Win 7 and win XP). I have a PSUS4 print server. Is there a way to setup the PSUS4 so that my server, Win 7 and Win XP computers could print to the HP printer? For example, If I setup the Print Server on the XP computer with TCP/IP port, could I share it to the server and Windows 7 computers?

Do you have any router or switch?
Or all the computers are connected to windows server through a switch?
PSUS4 must be connected to the router or the DHCP server so that it will get IP address and all the computers will be able to print.

TCS gen 2 and Windows server 2003 support

Hi,
I have a Cisco TelePresence Content Server v5.3 running on gen 2 hardware.
From what I can see TCS v5.3 only works in Windows server 2003, this is a concern as Windows server 2003 support is ending July 14, 2015.
Is there anything that can be done to mitigate the above problem without having to purchase the gen 3 hardware?
Kind Regards
Ed

The supported deployment methods right now for the virtual TCS is for it to be installed on existing TCS hardware, either 2nd or 3rd Gen server only, 1st Gen servers aren't supported, but you can migrate from a 1st Gen to either of the latter two. You'll basically be wiping the old hardware servers and installing VMWare on them to run a single instance of Windows and the virtual TCS application. As Wayne said, support for 3rd party platforms is coming, Cisco knows it's a big deal for customers and a solution needs to be provided and not just limited to existing TCS hardware.
You would migrate your existing license and option keys to the new servers by looking them up from the registry and creating a license file to be used during the install process.
Support contracts will migrate as well, the serial numbers will remain the same, but the product IDs might change to reflect you now having a virtual TCS instead of hardware. However, I'm still working out the details of the product IDs from my migration I did back in August, though that hasn't stopped me from getting TAC support.
To give you an idea of the process, take a look at the TCS 6.1 VM Install Guide.

Cold fusion 8 and Windows Server 2003 Administrator Login

I cannot seem to login to my coldfusion (trial version)
administrator login after installed successfully on my Windows
Server 2003 with Web Edition Service Pack 2.
It tries to go here which is correct
http://127.0.0.1/CFIDE/administrator/index.cfm
But I get
Bad Request (Invalid Hostname)
I attempted to go through IIS through default Web Sites and
browsed over to
http://192.168.10.19/CFIDE/administrator/index.cfm
and I now get a "The page cannot be found" display message.
Is there anything special I need to do, perhaps in Web
Service Extentions in IIS or something since I don't see
"Coldfusion" mentioned anywhere, and I can't seem to find any clear
instructions on the Adobe site.
Please help, thanks.

You should
configure
IIS for Coldfusion. Pay particular attention to the section "To
verify your IIS configuration".

AFP and Windows Server 2003 (SP2)

Hello,
I have a problem when i connect my MAC with Windows Server 2003 by a AFP connection the connection drops after +/- 10 min. I need this AFP connection because i work with a OMNIS database that locks when i use a SMB connection.
Can somebody tell me why the connection drops after a while ?
Thanks already,
Marco

Hi Karen
Unfortunately, re-posting to a different forum category
doesn't help. Almost all of us here are already watching all the
categories. If an answer is known, we normally pounce on it to try
and help. So your situation is probably pretty unique and eluding
us.
Please direct any replies to this question to where it was
originally asked by
clicking
here.
Cheers... Rick

Windows server 2012 as primary DC and DNS server and windows server 2003 as secondary DC and DNS

Migration from windows server 2003 AD DC and DNS server to windows server 2012 R2,
Cannot I set up Windows server 2012 R2 as primary DC and DNS , windows server 2003 as secondary DC and DNS ? (for backup server when server 2012 fail, user can continue to login and access internet services)

You can mix both as long as your Forest and Domain Functional level are Windows Server 2003. However, I would like to bring your attention to this blog about known problems when mixing DCs with Windows Server 2003 and 2012 R2 OS:
http://blogs.technet.com/b/askds/archive/2014/07/23/it-turns-out-that-weird-things-can-happen-when-you-mix-windows-server-2003-and-windows-server-2012-r2-domain-controllers.aspx
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

MS-6337-LE5 (815EPT) and Windows Server 2003

Just out of curiosity, will this board work with Windows Server 2003?
I'm inclined to think not.
Servers generally require special memory and multiple processors, but I figured I'd ask anyway. My boyfriend, who also uses this board, is thinking of upgrading to Windows Server 2003.
If that is not possible, he wants to go with Windows 2000 Pro instead. He does not care for XP wants to stay away from it.

I use Google search and the 1st result hits the bullseye .
There you go : Windows 2003 Server System Requirements Page.

Msi K9N2 Platinum SLI and Windows Server 2003 r2 32 bit edition

Similar Messages

Maybe you are looking for