MSI KLN2 DELTA problem hangs after testing RAM

I currently purchased the MSI K7N2 DELTA-L (Motherboard) NFORCE2 CHIPSET DDR400 and for the cpu im using an athlon 1800+ and i just purchased some pc 3200(ddr400)of 1 gig(stick by Samsung) and i have a problem during boot up it's a really weird problem as soon as it says testing memory it goes up to 1048 detecting the 1 gig and it says ok saying single Channel and then as soon as it says detecting ide hard drives it hangs up. I can't even acess CMOS now i have had the problem for over a week, & send the motherboard back to xtreme gear that i bought, & they send me a new motherboard and it's the same problem. So I'm thinking that the mother board doesn't like the ram i purchased I have tested the ram on another system that supports pc3200 except it was on a system w/ a pentium 4 and it worked perfectly on that system. i have also put samsung 512 mb stick and same problem, does any one have suggestions or solutions, is samsung just not compatible with msi k7n2 delta series mother board or what else can it be, I can't update the bios cause right after or even sometimes b4 it says detecting ide hard drives it hangs up any solutions??????
The link to the ram i bought is
http://store.yahoo.com/dccsale/sa1gpc400mhz.html & I've tested it on a p4 motherboard with a pentium 2.6 and it worked perfectly but maybe its not the ram maybe the bios on the msi k7n2 deltas are very glitchy???

Do u think it might be cause im using an athlon 1800+ or is it my 1024 mb or 1 gig pc 3200 sometimes i do get something in the screen but right after testing the ram it hangs up or even if it says detecting the ide hard drives and nothing after that i know my vga card is fine i know my ram is fine and it's abviously not a hard drive issue so not sure what the problem is and it's basically impossible to flash the bios if i cant get in or even to load up where it checks the floppy... The only thing is if my cpu was bad i think nothing at all would load on the screen, but if it's possible i guess what esle can i do should i spend $150 and get a faster cpu like an athlon 2700+

Similar Messages

MSI KT6 Delta PROBLEM

First, my hardware :
Everything running @ default speed & settings.
AMD XP 2700+ (running @ about 47C idle and about 55C in work)
MSI KT6 Delta (v2) with latest bios
512mb DDR (333) CL2.5 Elixir
Seagate S-ATA ST380013 (80gb), with WinXP Pro (SP1) installed
Samsung SP1203N (120gb), as primary master on IDE1
Samsung 52/32/52x CD-RW, as secondary master on IDE2
Connect3D Radeon 9600 128mb
PSU Antec TruePower 380w:
+5V 35A
-5V 0.5A
+12V 18A
-12V 1.0A
+3.3V 28.0A
+5VSB 2.0A
I keep getting some strange BSOD. No matter what I do with the machine. Windows locks up completely and after about 1min, that BSOD comes and machine boots.
( http://www.saniainen.com/bs.jpg )
In normal usage, it comes about 1-3 times/day.
Mostly it comes when I copy some files from disk to other.
But it comes everytime when I try to decompress big (over 400mb) ZIP-files.
Everything did work with my old board, MSI KT4A. The problems begun when i changed the motherboard and added the Seagate S-ATA hdd.
I have ordered new memory, Kingston HyperX 512mb (333). Could it be memory-related or something with S-ATA ????
I have tried everything, latest BIOS, latest VIA4in1, memchecks etc...

I had the same problem on a differnt mobo and all I did to fix it was switch the IDE cables around on the devices.
?Give it a try?
It may be a jumper you forgot to change on the IDE devices.

XFX GeForce 7600GS 512mb AGP with MSI K7N2 Delta Problem

Hi, I have been searching in everyplace and still I havent find a solution.
I have the XFX GeForce 7600GS 512mb AGP card.
I use the MSI K7N2 Delta.
My Processor its the AMD 2600+ XP
my PSU its a 420watt
my RAM its 2gb DDR 400
I made everything in the bios, didnt work.
I updated the lastest drivers and bios, didnt work.
I went to a friend house, he use a P4 motherboard with 500watts. Worked, PERFECTLY.
I changed the card once (the first one didnt worked at all) but this one worked...
now the question is:
HOW I MAKE IT WORK IN MY PC ?????????
Can anyone help me? I dont wanna sell it to a friend for only 60$ (that the only costumer I have found for the card in Panama)

Heh I had problems with trying to see again was what happening in my PC but yesterday....
Ok I went to my friend house, we used the card with his 350 watts 15A in the 12V+ and it worked.
Then we tried to install the PSU but I dont know why its 4pin was incompatible with mine....
Well heres the important part: I went to a local Computer Store where they repair too and with another more powerfull PSU in my PC and the card didnt worked for seconds, but the guy played a little with my Ram and he noticed that its posible to that be the problem. Remember that my ram its a Kingston 400DDR 2X1 Gb running in the purple and the green slots of the mobo. when we changed them to both purples slots of the mobo the PC dosent work and make a the beep sound. I have the braket in my computer and it showed a red dot here: GR
GG
Gonna search the manual to know what that means.

MSI k8n neo platinum hangs after post single beep

Today I powered off my computer, and when I tried to power it back up the x850 fan just runs at full speed, and never drops to idle and the screen stays dark. If I reset the bios then it will post as far as asking to press Del to enter setup, but freezes at that point. This thing has been running like a champ and this is the first problem I've ever had! I unhooked/unplugged everything but the keyboard/video/ram/cpu. Tried running with four different memory modules in single channel and dual channel but no luck there either. None of the hardware below has been changed in the last six months. Any ideas? TIA!
The indicator lights read:
R G
R G
According to the manual this means:
Testing Base and Extended Memory
Testing base memory from 240K to 640K and extended
memory above 1MB using various patterns.
AMD 64 4000+
MSI K8N Neo Plat Rev1
PQI BH5 512x2
ATI x850 AGP
SATA 10k RPM Primary
Antec P/S

Quote from: flobelix on 07-February-07, 07:09:19
Core2Duo E6400 would be a gain of about 15% compared to 4000+ ( in games 1024x768, no aniso or aa). Quality options and better resolution would shorten the gain. Other applications than games e.g. cinebench would run a lot faster on the C2D. The main advantage compared to the 4000+ would be dual core because many future games will be optimized for this. Question is: Is this worth $272?
With only one 7600GT installed you won't be able to play most of the new games in full detail because of lacking 3d power although Core2Duo installed. The gain of cpu performance will be therefor useless (if main focus is on gaming). 7600GT sli-array would be an option for full detail and using more cpu power but it would also be slower than one 7950GT for nearly the same amount of money spent for 2 7600GT.
1. If you need a gaming pc I'd only buy a new C2D if you can also afford high end vga. Otherwise cpu power is wasted.
2. 7600GT is only an option if you want to save money now and you want a second one later. Buying two now to get a sli-array isn't very clever. Less performance than 7950GT, same price.
3. Buying one gig of ddr2 isn't very clever either. More and more applications need more than 1 gig (for example vista!). When changing to ddr2, change to 2 gig dual channel kit.
4. Getting $300 for your old stuff seems quite optimistic to me.
Conclusion: Save your money for better vga! Take back 7600gt, keep old vga and 4000+, wait for a little time and buy Geforce 8800 GTS. Increase of gaming performance would be unbelieveable. After providing high end vga you can upgrade to C2D in next step and receive a noticeable increase of performance in all kinds of applications.
Hmm.. very good points. I went and read some reviews of the upcoming 8600 and 8800. They are quite impressive for the money. I believe I'll return everything and find a limp-a-long $50 mobo to replace the dead msi. It looks like holding out for quad core with dual SLI is the real gain over my current setup. On a side note I won't be running vista until after sp1 or possible sp2. No tangible benefit to me! What suggestions do you have for a solid performing mobo for the following:
socket 939
4 240pin DDR slots
AGP (My X850 XT is still strong enough for everything I do)
SATA 1.5 (no need for the faster one as I have none of those drives)

MSI P45-8D problem: reboot after loading startup services (windows seven 64bit)

hi guys!
I decided (buying a cooler master elite 360) to keep my Memory Lover (whit ddr3/ich10r, pci-ex 2.0), which is actually the 'best purchase for me (rather than a G41 mATX) .
But then, after I had solved the problem of overheating in the pci-ex, and I put the board in its box for weeks, now has a new problem:
Continuous blocks & reboots just after loading startup services windows seven!
The setup is this:
Windows Seven 64bit
MOBO MSI Memory Lover
CPU Xeon L3110
VGA MSI Radeon HD5450 1gb ddr2 fanless
DDR3 1333 4GB
PSU Tacens Radix V mATX 35Watt Velociraptor + Caviar Green
DVD burner (sata)
Esi pci-ex sound card connect module
Creative Xtreme Gamer (disconnected for now)
I have many ram models that I can put in:
kingston lovo 4gb 1333
4g-skill eco 4gb 1333
adata green 4gb 1333
corsairs white 8gb 1600
All memories can work undervolt at 1.35volt, but-of course-I keep them in standard 1.5Volt for more stability
I also tried a single 2gb stick at a time, but nothing has changed
when the system reboots (I infer) windows finished loading all the startup services (including antivirus, network drivers, audio drivers, etc. ..). and I can say with near certainty, that the last major service that is loaded, is the catalyst control center ...
I suspect an incompatibility with Memory Lover & the Video Card's ATI driver ..
I also tried to uninstall and clean with driver sweeper, but the problem remains ..
Besides this I also have a problem with the temperature of the processor xeon l3110 (45watt tdp)
cpu heatsink as I have a Arctic Freezer LP 11 (Capacity Cooling 100W).
with thermal compound pre-installed I had 60/70 degrees recorded.
I changed the thermal compound with the famous Prolimatech pk-1 and now I measure 80/90 degrees ...(and I've changed a lot of thermal compound that I put with my eyes closed)
now, this is not possible because:
-I know the processor, I kept in daily use at 3Ghz with a noctua nh-U9B se2, and in summer never exceeded 40 degrees (d 'winter was about 30 degrees)
- Either with the Scythe kama thermo, that with my finger, the heatpipes of the Freezer 11 LP, the Mosfet, the NB & SB are all cold .. the 5450 is 40 degrees or so, but it is fanless, and its temperature is in its normal ..
What can you tell me of my two problems:
- Continuous reboots after loading windows seven
- High temperature cpu (probably not real)
I remind you that a few months ago the team & Memory Lover Xeon L3110 worked perfectly.
The PSU is a new 350Watt Tacens Radix V mATX ... the system at idle consumes 70/80 watts (measured at the wall) ... I think it Is not a problem of the little power supply for the needs of my system ..
and anyway I can try to use an old Enermax 450watt Liberty, which I keep for emergencies..
thanks
max

guys,
I solved the problem!
the sink was installed wrong, and did not touch on the processor!!!
the problem was the mosfets around the cpu that make thickness in height ..
the thermal paste was put well and ... still immaculate!
processor took about 20 (or more) of restarts and very high working temperatures!
it rocks!!
I can now say that the 'AC Freezer 11 LP is sensational!
The Xeon L3110 (with EIST, C1E & Acpi active together, That downclok it) works now to 23-25 degrees!!
I have installed the ddr3 kingston 4gb Lovo 1333 + 8GB Corsair 1600 1.35Vram white.
(with 12GB, I can easily do a large Ramdisk for temporary files).
I installed hd5450 driver manually, but still the catalyst control center does not appear at startup
here is the screen of the situation:
finally...but how did I doubt the quality of this MSI board?

Msi z77a-gd55 xmp missing after add ram

hi
i have msi z77a-gd55
at start i have 2 stick of ram of kingston khx1600c9d3 and i have the option to set xmp mode
but now i install two other stick of ram the same ram buy from kingston
i have done a clear cmos
and the computer boot without problem
but in the msi bios the xmp option desappear and i don't know why
my bios is up to date
anyone have an idea

I know this is not a new tread.but i have the same proublem with my MB msiZ77A i put in 2 sticks of
kingston 8meg each at 2133mhz.and mb, is only showing 1333.at the top of screen.I went down the
screen and Changed the Freq from 1333 to 2133 and clicked Save and shut off the computer. I re booted
and went back to look and at the top of the screen it still says ddr Freq is 1333. but when you scroll down
you can see that the new Freq of 2133 is their.
Shouldnt the bios see that i changed the speed?and also show the NEW speed of 2133.
tks
John

MOVED: XFX GeForce 7600GS 512mb AGP with MSI K7N2 Delta Problem

This topic has been moved to Retired motherboards.
https://forum-en.msi.com/index.php?topic=124849.0

Heh I had problems with trying to see again was what happening in my PC but yesterday....
Ok I went to my friend house, we used the card with his 350 watts 15A in the 12V+ and it worked.
Then we tried to install the PSU but I dont know why its 4pin was incompatible with mine....
Well heres the important part: I went to a local Computer Store where they repair too and with another more powerfull PSU in my PC and the card didnt worked for seconds, but the guy played a little with my Ram and he noticed that its posible to that be the problem. Remember that my ram its a Kingston 400DDR 2X1 Gb running in the purple and the green slots of the mobo. when we changed them to both purples slots of the mobo the PC dosent work and make a the beep sound. I have the braket in my computer and it showed a red dot here: GR
GG
Gonna search the manual to know what that means.

IBook G4 - Problems Starting after installing RAM

I installed a 512 MB RAM chip last night, triple-checked it for correct specifications. I've installed, uninstalled, and re-installed it several times, each time getting the same problem. I turn my iBook on, the start-up screen does its thing, and then it stops at the message "Login Window starting," right before my desktop would normally load. This does this with and without the RAM installed. I tried the disk utility CD 1, and it didn't seem to do any good. Any suggestions?

Does the iBook boot and run from the install CD?
If so run DiskUtility from the pull down menu. Still runs OK?
This would seem to indicate pretty good functionality.
Is it possible your software configuration wasn't healthy before you installed the RAM? You might have to do a re-install of the OS.

MSI K7N2 Delta-ILSR MB Problems, Need Help ASAP!! PLEASE

Ok I just got this motherboard (MSI K7N2 Delta) Yesterday and after getting it setup I began overclocking the Processor (an AMD Athlon XP Barton Mobile 2500+) I was at 11x 215 1.750V Perfectly. I moved to 216 it started to seem unstable so I pushed the VCORE up to 1.775 and tried 217. It couldn't boot so I dropped it back down and decided ok 208 and a 11.5 multi might get me past the 2.4 mark which I was looking for. Well when I changed the Multi. to 11.5 and said save the system just sate as the flashing y for save. I could not change it to n I had already pushed enter So i firgured great and left it alone for a few minutes, nothing so I reset it. Now it refuses to boot/post. It spinds the fans the HD's the Network port is going but I get no picture. I have cleared the CMOS using the jumper I have removed the battery and power for over an hour and I still get nothing. I am assuming this is a BIOS error but I am not sure what to do to fix it. Does anyone here kno maybe, something I have yet to try something I can do? I would hate to RMA it and have to wait on newegg. Hell the thing is a day old. So please any idea's are welcome I have this posted on the Hard Forums as well but I am hopinh this forum may be more popular with getting help as no one is helping over there. Thanks!

Hi,
Cross: Just in case you are doing something wrong there's a clear CMOS guide here, follow it to the letter (and don't forget to put the FSB jumper to SAFE beforehand - there's a note about it in the guide).
How To Clear the CMOS
Your system board or CPU maybe not be dead yet - I had a similar problem with one of my boards and I tried everything - to cut a long story short I eventually got it working!!!
Btw, If you can't boot or get into the BIOS put your other CPU in (clear BIOS again after fitting!), so that you can prove whether your motherboard is working correctly!
Good luck! I'm off ta bed!
Axel

Problem after testing 100 products

I use Labview to control a test machine. There is an 6251-M series DAQ board for analog signals to be acquired and PCI 6509 for Digital I/Os. I also control an AC motor drive via serial port(Enable, start, stop and speed ref.). The problem is after testing an amount of products(e.g. 100) the cycle time of the test increases(from 10sec to 20-30-50sec). I saw that this caused of misreadings from serial port(because I read the speed via serial port to switch between steps). Why it doesn't happen at first and starts after making an amount of tests. What can I do about this. How can I make sure the readings to be the same everytime? And make the cycle time fixed.

MSARIKOC wrote:
I use Labview to control a test machine. There is an 6251-M series DAQ board for analog signals to be acquired and PCI 6509 for Digital I/Os. I also control an AC motor drive via serial port(Enable, start, stop and speed ref.). The problem is after testing an amount of products(e.g. 100) the cycle time of the test increases(from 10sec to 20-30-50sec). I saw that this caused of misreadings from serial port(because I read the speed via serial port to switch between steps). Why it doesn't happen at first and starts after making an amount of tests. What can I do about this. How can I make sure the readings to be the same everytime? And make the cycle time fixed.
Maybe a memory leak?
Opening ressources (References and not closing them?
Creating a report string or logstring or log-array?
Greetings from Germany!
Uwe

App store hangs after Mavericks

After installing the upgrade to Mavericks on my early 2011 MacBook Pro with 8Meg RAM and 750Gb HD, App Store hangs. Any clues. Tried the usual solutions, like repairing permissions, checking disk integrity etc. Any suggestions would be appreciated.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

MSI K7N2 DELTA -L (601-6570-020) nFORCE 2 DUAL 400 , RANDOM RESTART PROBLEM (WinXP,Win98)

Machine Specs:
- AMD Athlon XP 2600+ With L2 512 KB (Model 10)
- MSI K7N2 Delta -L nFORCE 2 Ultra 400 (601-670-020) (My AwardBios is updated to v5.7, Using nVIDIA`s O/B Audio and Ethernet Controllers)
- TwinMOS PC3200(CL2.5) 512 MB DDR400 RAM (Desktop Series)
- Samsung SpinPoint (SP0411N) 40 GB 7200 Rpm HDD
- GeForce2 MX400 64MB AGP 4x (Oem Manufacturer)
- Samsung SyncMaster 753s 17" Monitor
- Sony 52x Cd-Rom
- Philips Stereo Headphones
- Windows XP Home Edition Turkish (Service Pack 1 Turkish) , I did all of critical and other updates ,Totally up to date.Device drivers are too...(nForce 3.13 whql International,Forceware 56.72 whql International)
Problem :
- ERROR EVENT : 1003 ERROR NAME : IRQL_NOT_LESS_OR_EQUAL
Original Error Texts:
A problem has been detected & Windows has been shut down to prevent damage to your computer.
IRQL_NOT_LESS_OR_EQUAL
If this is the first time you've seen this Stop error screen, restart the computer. If this screen appears again follow these steps.
Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If the problem continues, disable or remove any newly installed hardware or software.
Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components restart your computer, Press F8 to select Advanced Start-up options & select Safe Mode.
Technical Information :
*** STOP: 0x0000000A (0x00000004, 0x00000002, 0x00000001, 0x804F1473)
Beginning dump of physical memory
Physical memory dump complete. Contact your system Administrator or technical support group for further assistance.
After restarting manually from the PC. I get the following message
The system has recovered from a serious error.
BCCode : a BCP1 : 00000004 BCP2 : 00000002 BCP3 : 00000000
BCP4 : 804F1ADA OSVer : 5_1_2600 SP : 0_0 Product : 256_1
C:\WINDOWS\Minidump\Mini042202-01.dmp
C:\DOCUME~1\DANIEL~1\LOCALS~1\Temp\WER3.tmp.dir00\sysdata.xml
And when I check EVENT VIEWER
Event Type: Error
Event Source: System Error
Event Category: (102)
Event ID: 1003
Date: 22/04/2002
Time: 5:55:03 PM
User: N/A
Computer: XXX-BOX
Description:
Error code 0000000a, parameter1 00000004, parameter2 00000002, parameter3 00000000, parameter4 804f1ada.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 53 79 73 74 65 6d 20 45 System E
0008: 72 72 6f 72 20 20 45 72 rror Er
0010: 72 6f 72 20 63 6f 64 65 ror code
0018: 20 30 30 30 30 30 30 30 0000000
0020: 61 20 20 50 61 72 61 6d a Param
0028: 65 74 65 72 73 20 30 30 eters 00
0030: 30 30 30 30 30 34 2c 20 000004,
0038: 30 30 30 30 30 30 30 32 00000002
0040: 2c 20 30 30 30 30 30 30 , 000000
0048: 30 30 2c 20 38 30 34 66 00, 804f
0050: 31 61 64 61 1ada
I installed 6 operating systems on my pc (WinXp Home Edition Turkish/English,WinXP Pro Turkish/English,Win98 Turkish/English) and tested it, but every time i meet the same thing (MS Blue Screen Of Death Sux...).I checked the WinXP`s logs and searched for error code`s meaning from microsoft knowledge database. They are saying nothing about this problem but the problem`s root is coming from a bad device driver. It seems to be a generic problem for all operating systems cuz all of them were restarting themselves randomly, before i close "auto-restart on critical errors" option.After i saw some messages on forums , i searched for my RAM maker`s home page then i learned that my RAM is assembled with VIA KT Series and SIS chips & optimized for them. I think nForce is too picky about rams.But i aint sure about where the hell is this problem coming from. If you guys are sure about that is an unsupported ram problem and knew the list of ram marks&models that supported by MSI K7N2 Delta -L ,please help me about this damn problem. Thanks for your help.
Note : I tried Asus Ati Radeon 9200SE 64mb g.adapter (some peoples told me thats about g.adapter), but problem continued.

If I read correctly in your specs I see only 11 Amps on the +12v Rail. Is this correct?
If so, I'd advise a PSU that has at least 18 amps on the +12v Rail, perhaps as low as 16 with the other rails to match as shown currently in your spec.
11 Amps is just way too underpowered for that rig. I am surprised it even boots.
At what point does the BSOD occur?

MSI KT6 Delta LSR SATA to PATA High CPU Usage Problem

Well recently I've switch to my one of my other motherboards on my network to a MSI KT6 Delta LSR, it was working fine after a reformat, but I notice a few problems and that is 100% cpu usage for SATA to PATA, and vice versa, which seems really crazy. Then my network card performance is ISDN speed sluggish, and I tested my line to be working 100% with another mobo. But when I put another NIC on the same mobo it suffers the same speed problems.
Any suggestions? The rig is specs:
Barton 2500+
Antec QuietPower 350W
200GB Seagate SATA HDD
40GB Seagate PATA HDD
ATI Radeon 7500 AIW
Audigy 2 Value
Realtek 8139 NIC
MSI KT6 Delta LSR Mobo
2x512 MB PC 2700 RAM
Pioneer 107D DVD Writer
LG 16X DVD-ROM
56K Modem (A-open)

Shouldn't say what I don't know about SATA, but since I found below, I need ask if VIA 4in1 drivers are installed, preferably while in SafeMode I say:
http://www.google.se/search?q=cache:X6ewgPiIHYcJ:www.qdi.nl/cgi-bin/bbs/YaBB.pl%3Fboard%3DP4I865%3Baction%3Ddisplay%3Bnum%3D1074174096+sata+to+pata+cpu+usage&hl=sv
I recently installed 160g Seagate barracuda 7200.7 drive on SATA port. (I enabled the Bios using Auto) I have a P4I865pea-6al mother board, with two PATA drives . When copying files between the PATA drives on ide ports, to or from, the SATA drive, I notice the CPU usage goes up to 100%, but when copying files from one ide drive (the PATA drives) to another the CPU usage is very low.
Is there a bios setting that will allow me to copy files from the SATA drive to the Pata drives using a small amount of CPU power, found when just copying between the Primary and Secondary IDE drives? I am using Adobe premiere pro, which uses a lot of CPU power, and the high CPU usage of the SATA drive crashes this program? Any help would be appreciated
Re: CPU usage with SATA drive?
« Reply #1 on: Oct 30th, 2004, 7:17pm » Quote Modify
have you installed the newest chipset- and ide drivers ?

Msi k7n2 delta ilsr problem

hi i have this configuration on my pc:
antec true control 550 watts
msi k7n2 delta ilsr
kingston hyper x pc3700 2x512 mb
athlon xp 3200+
seagate 120 gb sata 7200.7 hd
ati radeon 9800 pro excalibur ice q
i have 2 problems : the first one is that sometimes windows display me a blue screen with certain problem related to ati2dg.dll i think that problem is beacause the video card so i decided to update the bios , in the live update page from msi says that the bios 7.6 fix a bug with ati vga cards but after flashing and updating to bios v7.6 that blue screen with the same error still appearing so i dont know what else to do to solve the problem and the second one is that when i start any game or make the processor to work a little mostly related with video stuff the case speaker start to beep and the pc lags until he restarts with no reason i really dont know why if u can help me thank you

Foxtrotccs,
In the BIOS try setting the AGP to 4X and disable Sidebanding. Then set the AGP Apeture to 256. See if that helps.
Make sure you are running the lastest nVidia nForce Drivers and the latest ATI Catalyst Drivers
Take Care,
Richard
P.S. There is still a possibility that the Kingston RAM is the problem.

MSI K7N2 Delta ILSR Memory problems

I'm trying to burn in a system in a 50 deg C (122 deg F) room for a minimum of 12 hours. The main system components are as follows:
Motherboard: MSI K7N2 Delta ILSR
CPU: AMD Athlon XP 2800+
Memory: 2x512 OCZ PC3200 EL
My problem is that the burn-in software continues to freeze up during the memory test. I've already contacted the software manufacturers and the software is stable. It's a problem with the way the motherboard handles the memory. I've tried putting the memory in dual channel configuration and changing the timing settings in the BIOS. The SPD settings are 2.5-3-3-7. Right now I have them at 3-4-3-8. It's a lot more stable than it was under the default settings but it still freezes up sometime after 7 hours. Unfortunately, I wasn't around when it froze so I don't know exactly how long it lasted. I can say that after 7 hours, it wasn't showing any slowdown in performance. If anyone could think of anything else I might be able to do to get the system stable, I would greatly appreciate it.

Thanks for the suggestions. The CPU FSB is 200, so it's already matched up there. And we have a ton of fans already. There are two in the front, 4 inside and 1 on the back. It's a custom case, 2u high. The power supply is oversized and more than adequate to provide the required power. I have four of these units running right now. Two with 2x512 sticks and two with 1x1024 sticks. For each combination, the memory clock speed for one is 166 and 200 for the other. I have been loosening up the memory timings trying to get the system stable, but it still isn't. If the power supply is good, and I'm unable to cool the system anymore due to limititions within the case, is there anything you can think of to stabilize the system. Maybe other settings in the BIOS or suggestions on how to go about getting good timings for the memory. Thanks.

MSI KLN2 DELTA problem hangs after testing RAM

Similar Messages

Maybe you are looking for