Msi km4m-v xp setup problems

I have just installed a new mobo to my system.
I have loaded default bios settings
The board will post ok and see my hard drive and dvd rw
it will the start to load win xp from cd rom
it gets to the point where it says SETUP IS STARTING WINDOWS and hangs
I have tried to run maxtors diagnostics tool and this cannot see any ide devices.
system
Athlon xp 2200
256 ddr pc2100 ram
pioneer 106 dvd rw
maxtor 30g hdd
msi km4m-v (ms -7061 ver 1.0 )
bios v1.2
the hdd is on its own cable on the primary hdd and configured as master
the dvd rw is secondary master
i have swapped cables. no change
i have removed the dvd rw. no change
i have put all components on to another board and they all work fine, i have also run power max on the hard drive with another board and this has low level formatted ok and verifyed that the disk is ok.
i tried turning off usb in the bios still no change
can you offer any help
thanks

You're welcome dude!
Here you can see the whole post that I've made when I was having troubles installing XP on my KM4M-V, also check that my old PSU was only 16a in 12V rail: KM4M-V Can't install...
Quote
can anyone please explain to me why this board seems to work fine with win ME loaded but has this problem with XP.
I can't be shure, but I guess that XP try to load a lot of components in memory while installing, also this can make the installation crashes because of memory is not getting enough power... That's only my guess, and I know I can be totally wrong... Any other ideas guys?
Here is a very good reading for PSU : Power Supply Guide
Also you can "caculate" here but it's only a reference but will help you a little: PSU calculator

Similar Messages

Msi Km4m-l Problem!!!! Help!!!!

BOARD: MSI KM4M-L
MEMORY: 2-128MB PC2700
HAR DISK: 40GIG SEAGATE
VIDEO CARD: GEFORCE2 MX400 64MB SDR
MODEM: D-LINK CONEXANT INTERNAL MODEM
CDROM: LITEON DVDROM
PROBLEM: WHEN INSTALLING XP, I ALWAYS GET THIS ERROR; IRQL_NOT_LESS_OR_EQUAL. I GET THAT ERROR BEFORE THE XP INSTALLATION COPIES THE FILES. WHEN I DISABLE, THE CPU INTERNAL CACHE FROM THE BIOS, IT WILL START COPYING FILES BUT IT COPIES FILES TOO LONG. HOWEVER, AFTER COPYING FILES EVEN FOR A LONG PERIOD, IT WILL RESTART AND I WILL ENABLE THE CPU INTERNAL CACHE. THE XP INSTALLATION WILL CONTINUE BUT WHEN THE XP INSTALLATION INSTALLED DEVICES, THE SAME ERROR COMES UP. TURN OFF MY PC FOR AN HOUR. TURN IT ON AGAIN, THE INSTALLATION WILL FINISH BUT WHEN I INSTALL SERVICE PACK 2 IT FREEZES AND NEVER BOOT ON XP AGAIN. WHEN I OPEN MY CPU, MEMORY AND HARD DISK ARE TOO HOT. DO YOU MY PC OVERHEATED? I ALREADY LOWERED MY MEMORY FREQUENCY TO 133. WHAT SHOULD I DO? HELP, ANYONE?

KM4M-L
Athlon 2000+ XP
300W PSU Generic
256MB DDR 333Mhz
17" AOC bLACK
40GB 7200RPM Seagate ATA-133
Liteon DVD 16x ATA-100
32MB GeForce2 MX400
56K Internal Modem
Moded Casing.
O/S --> Windows XP
Sorry for the all caps post, i'm used to it. Anyway, as for my problem, I always get this error message: IRQL_NOT_LESS_OR_EQUAL. The only thing that works was disabling the CPU Internal Cache from the BIOS but it resulted in slow installation. I only disable the cache when copying the setup files coz I can't get through that setup process if I won't disable it. After copying the setup files, it will freeze from the moment it resumes the setup. I need to turn off my pc for an hour for it to continue the setup. It'll finish the setup but it will freeze while installing Windows XP Service Pack 2. After it freezes, I restarted it and it never booted again. It will auto-restart from the moment it showed the Windows XP logo. What do you think?

MOVED: MSI-KM4M-V Boot Problems

This topic has been moved to AMD SocketA based board.
MSI-KM4M-V Boot Problems

Fredrik:
Thanks for backing me up while I was out of the forum.
Usually, when I clean my cpu, I use a Q-tip damped with Isopropyl alcohol and then remove the remaining grease on the processor die. For the heatsink, I use the same Q-tip or a piece of damped cotton with isopropyl alcohol also.
I like the idea of the nailpolish remover since it makes sense because it can remove even the toughest resin.
See you later, and I hope our new friend has sorted the problem.
Edyros!

MSI KM4M-V SKT problems

Right its my birthday today and my other half is building me a computer
we are having problems it seems with the mother board
MSI KM4M-V SKT
we get no screen ouput whatsoever the board has a extra connecter a 4 pin thing this is plugged in any ideas?

Quote from: Fredrik Åsenius on 24-September-05, 05:40:27
What a birthday, huh? I hope you and the better half is taking it alright!
What comes alive? No beeps?
If all fans start spinning, but nothing on screen, I recommend you take the mobo out of the case - after pulling power cable out - and put it on a non-static surface.
Reseat the memory in a new slot. Before powering on again check for visible damage.
Slightly edited, as Wannakanoby beat me to it.
after staying up till 5 am so itd be ready for me to play the sims the poor loves tearing his hair out but will try that now
any other suggestions are thankfully recieved!

Speed Problems with MSI KM4M-L SKT A

I have recently purchased an AMD Athlon XP 2600+ (333MHz FSB) Processor, and an MSI KM4M-L SKT A motherboard which states that it has an FSB of 333MHz. On the motherboard I set the jumpers for the CPU speed to 166MHz because I assume that because of DDR it makes it technically 333MHz?? However when I try to install an operating system I get random file errors, eg File NTLDLL.DLL not found, even though the file is there. If I change the CPU Speed to 100MHz or 133MHz then everything works fine. Any ideas on how I can get the computer to run at full speed without any errors??

Please give complete PC. specs. includding P.Su. brand and how many Amps. it gives to 3.3v. 5v. and 12v.

Request for proper BIOS settings for MSI "KM4M-V" VIA KM400

Hello,
I tried to search on this problem but with no success. I have a computer that I had to reset the bios and I'm trying to get the clock speed adjusted to the processor chip. Here is my setup:
MB = MSI "KM4M-V" VIA KM400 (MS-7061)
CPU = AMD ATHLON XP 3000 "Barton" 333 FSB OPN - AXDA3000DKV4D
Here is my problem, when I boot up the cpu shows the clock speed of 1.733 GHZ with default BIOS settings.(it shows this speed in windows when booted up also) When I try to go into the BIOS and change any of the speed settings under Advance Chipset Features, the cpu will reboot and loose video until I reset the BIOS with the jumper.
I was wondering if someone had a setup like this and could give me info on what settings are the RIGHT ones to get the AMD XP 3000 up to speed? ;-)
Any help would be greatly appreciated!!!

Quote
Did a search on the form and looked thru that posting guide with no results.
Read >>Posting Guide<< and provide full system specification.
Quote
how do you find CPU OPN code?
Look over CPU itself:

Does PCI Express Video Card compatible on a MSI KM4M Motherboard

Does a PCI Express NVDIA Video Card (8500GT 512MB/128Bit/DDR2) compatible on a MSI KM4M Series Motherboard (System Model: KM400-8235)?
Is it possible to setup the PCI Express NVDIA Video Card on the MSI Motherboard PCI Bus Slot?
Thanks for any response.

Quote from: saijin on 11-January-10, 10:44:44
Maybe this is a dumb question..
There's no way a PCI-e card will work on that board. AGP yes, PCI yes, PCI-e no.

Pinnacle PCTV Stereo and MSI KM4M-V mb

I cannot run my Pinnacle PCTV Stereo card on my new MSI KM4M-V motherboard, regardless of the BIOS settings, IRQ assignments, operating systems (Win ME, 2k, XP) and of the inserting the PCTV card in any of the three PCI slots available.
However, after installation, the "PCTV Assistant" does not report any problems!
Nevertheless, only various stripes appear in the TV window, and no sound at all. Channel scan brings nothing. However, while scanning, on finding the not empty TV channel, the pattern in the TV window changes from more or less random set of white spots (like snow) towards some stripes.
The same PCTV Stereo card worked fine with my previous motherboards (ASUS CUPLE-VM, ASUS CUSL2, AsRock K7S41GX).
The PCTV card is the only PCI card installed. The hardware configuration is: Sempron 2400+, graphics and sound - integrated with the mb, DDR 512 MB in one module, HDD WD Caviar 80 GB 8MB cache.
Maybe somebody could help me resolving this problem? Many thanks in advance!
Andrzej

Hi,
so far I could not try another PSU.
In the meantime, I was informed that there can be the problem of the type of PCI interface. If the tv tuner was PCI 2.2 compliant, no problems should occur. Could anybody tell me more about these types of PCI interfaces? What I found elswhere in the net it was the division of TV tuners into 3 groups regarding the PCI interface: "PCI cards", "PCI 2.2" and "PCI 2.3". I presume that the my one belongs just to the first group (PCI cards), like the majority of the TV tuners on the market.
Can anybody tell me about the differences between these types of interface, and maybe you could help me overcome this conflict, IF IT IS REALLY A CONFLICT!
Andrzej

I need to upgrade my 10.5.1 os on my G4/1.25 (I'm having some audio-midi setup problems), but it's a machine that is not connected to the internet. Do I have any options? Thanks!

Friends,
I'm having some audio-midi setup problems on my G4/1.25/10.5.1 machine. I'm thinking that a routine OS upgrade might help. However, this machine is not connected to the internet. Are there any alternate methods for upgrading system software? Thanks in advance!

OK, what you should do is download the updates on another machine and burn them to a disc. Start at this link http://support.apple.com/downloads/#leopard for downloads and find, among other things, the 10.5.8 combo updater that works on PPC machines, plus security, QuickTime and other updates. Going from 10.5.1 to 10.5.8, there will probably be a bunch of things that you should install. Being off the internet with the machine, you can't have Software Update sort it out, so something might get missed, unfortunately.
My suggestion is this: if it looks like you might need a download, get it onto that disc.

MSI 870a-G54 Hard drive problem.

About a week ago i reinstalled Windows because it started to slow down (virusses and what not) And as soon as i reinstalled everything (programs games etc etc) One of my harddrives used for games did not show up at the bios and at My computer.
So this entire week i've been trying to get it to work again and i've narrowed down the problem today to the BIOS and/or motherboard not giving the power to the HDD in order for it to start and be recognized in BIOS and Windows.
What ive done to come to this conclusion:
- Reinstalled Windows twice,
- Replaced CMOS Battery,
- Flashed the BIOS to every BIOS setting the MSI website had to offer. None worked for the HDD to get powered up again.
- Moved CMOS jumper,
- Changed SATA and powercables on harddrive,
- Tried the HDD on another test PC i had and reformatted it there as well,
- Only hooked up the not working HDD to the PC, (HDD did not spin up, and came to the conclusion at this point that motherboard or BIOS is the culprit)
- Unplugged the powercable to the not working HDD and plugged it back in when the PC was running and i could feel it spinning up, after this i restarted the PC so that the HDD would still get power and it was recognized by the BIOS and Windows and i could use it. As soon as i shut down the PC entirely and restarted it the HDD would not spin up. And i had to unplug power to the HDD and plug it in again and restart PC for it to work properly.
- Checked for bad sectors nothing found,
Everything else is working perfectly. Except that one HDD not getting the power when booting up the PC.
The HDD in question is the "Samsung HD502HJ 500gig" used for Steam games.
PC Specs:
CPU: AMD Phenom II x4 955 Black edition. Put on a new CPU cooler last summer (Cooler master Hyper 212 Plus)
Mobo: MSI 870a-G54
PSU: Antec EarthWatts EA650 (650 Watts)
Graphics card: Powercolor PCS+ HD5870 Put on a custom cooler last summer (Arctic Cooling Accelero Xtreme 5870)
RAM: Kingston ValueRam 1333Mhz DDR3 (8gigs 4x 2gig) Bought 4 gigs extra last summer
HDD1: Seagate ST3160812 AS 160gig used for Windows 7 Ultimate 64 bit (Works perfectly)
HDD2: Samsung HD204UI 2TB used for Storage / Other games than i have on Steam. (works perfectly) Bought last summer with the cooling/system upgrade
HDD3: Samsung HD502HJ 500gig used for Steam games. (Does not work anymore after reinstal) Bought 2 years ago along with the rest of the PC
I am completely at a loss here as to what the problem is. I do not have the funds to buy a new piece of hardware at this time (i think the entire week of struggle would back that up for me lol...). And ive basically tried everything what i know and what i've found through Google and friends. Might have been better going straight to MSI forum and post my problem here but narrowing it down to this not only helps me but the person that is going to post below in this thread as well lol.
Thanks in advance and i hope to hear from anyone soon.

Quote from: Bas on 09-March-12, 19:16:21
Try drive in different PC, as it looks like it died.
HDD's always spinup as soon as power is applied, ergo I think the drive died.
Ive tried it already in 2 different PC's and i have to apologize here for not mentioning that earlier in the topic.
The drive spins up perfectly in both of those PC's and ive checked for bad sectors on both of those PC's as well and it showed that the drive was 100% healthy on both PC's
The drive was working perfectly fine before the reinstallation of windows. Thats why i dont think the drive has died. Because it would be weird that the drive just suddenly gave up right when im reinstalling windows..
It also doesnt add up when i plug the powercable back into the drive while the PC is running and it spins up then and works perfectly until PC is shut down. Thats why i had it narrowed down to the BIOS and/or Motherboard being the culprit.
My best guess is that its software related because the PC does boot up so its not a hardware problem.
P.S.
A friend of mine said that it could be a powersaving issue. But ive looked into the BIOS and i could not find anything about it.

Setup problem, windows xp, firefox upgrade to 4 and asked to reboot but did not progress. keeps asking to restart even if I try to remove

setup problem, windows xp, firefox upgrade to 4 and asked to reboot but did not progress. keeps asking to restart even if I try to remove

Hi marsano,
Usually the only reason it will ask you to reboot is if there is a file that must be modified that the updater doesn't currently have access to. You should try running the Firefox program once as Administrator:
* Right-click the icon and choose ''Run as Administrator''
If that doesn't help then do a clean reinstall.
# Download a fresh copy of Firefox from the [http://www.mozilla.org/firefox/fx/ Mozilla download page] and save the file to the desktop.
# [[Uninstalling Firefox|Uninstall]] your current version of Firefox and remove the Firefox program folder before running the new installer.
# Run installer
Remember that you don't want to remove personal data when uninstalling. That way you'll still have your personal information.
Hopefully this helps!

Install and setup problem with Acrobat XI pro

I have downloaded the Acrobat XI Pro trial program, with no error messages. When I clisk on "setup.exe" the following error message appears, see screen shot :
"This patch package could not be opened. Verify that the patch package exixts and that you can access it, or contact the application vendor to verify that this is a valid Windose Installer patch package"
How do I get setup to start?

@Jeff -- Yes I did use theDownload assistant. Down load completed and assistant started the insall. Received the error message and install terminated. Searched for and found the install folder and have tried install by clicking on"setup.exe". Have not tried a fresh download, did the MSI logging, see next reply.
@LeoAdobeX -- I renamed the file\folder path and eliminated all spaces. Clicked setup.exe and received same error message.
Enabled MSI logging and tried setup.exe, received same error message. Have posted 2 most recent MSI files and the setup.ini file. Here are the links:
https://workspaces.acrobat.com/?d=SxkkNEXK*bJLZnkDjFdWiQ
https://workspaces.acrobat.com/?d=Mdt6KyNSpBViV3h2ZC2pUg
https://workspaces.acrobat.com/?d=AOxVXVIBozy1XrFDwzljoQ
Thanks for your help. Will stand by,

MSI ex600 sound headphones&speakers problem

Hello all I have MSI ex600 and i have problem with my sound
When speakers playing some music and i want hear it in my headphones its problem because speakers playing away
So i hear music on headphones and speakes too
I try find some solution (and its many problems with this stuff) but for me didnt work
Some information of me Sound card :
Sound(a) : 82801H ICH8 Family HD Audio Controller module: snd-hda-intel
[root@SilentHill ~]# lsmod | grep snd
snd_seq_oss 33408 0
snd_seq_midi_event 7936 1 snd_seq_oss
snd_seq 55936 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 7956 2 snd_seq_oss,snd_seq
snd_pcm_oss 42400 0
snd_mixer_oss 17024 1 snd_pcm_oss
snd_hda_intel 374568 3
snd_pcm 82312 2 snd_pcm_oss,snd_hda_intel
snd_timer 22536 2 snd_seq,snd_pcm
snd_page_alloc 9232 2 snd_hda_intel,snd_pcm
snd_hwdep 9096 1 snd_hda_intel
snd 57320 15 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_hda_intel,snd_pcm,snd_timer,snd_hwdep
soundcore 8096 1 snd
[root@SilentHill ~]# cat /etc/modprobe.conf
# /etc/modprobe.conf (for v2.6 kernels)
# alias wlan0 ndiswrapper
# --- BEGIN: Generated by ALSACONF, do not edit. ---
# --- ALSACONF version 1.0.15 ---
alias snd-card-0 snd-hda-intel
options snd-hda-intel index=0 model=5stack
alias sound-slot-0 snd-hda-intel
# --- END: Generated by ALSACONF, do not edit. ---
That was my last stuff what i tried (options snd-... in modprobe.conf)
Thanks and sorry for my bad english

Add this to your modprobe.conf :
options snd-hda-intel model=3stack-6ch
It will add a headphones switch to your alsa control which if you disable will mute the onboard speakers.
Works on my MSI vr600

Simple VISA Setup Problem

Hi all,
I'm having issues working with VISA in LabVIEW. Previously, I've used Peek/Poke VIs (before they were VISA VIs) that allowed me to read and write directly to registers at a given Windows address. I have a new, custom PCI Express board that uses the same architecture that I've worked with previously only this time I'm trying to access the registers using VISA.
As this is my first time using VISA, I'm having some setup problems. Yesterday I got to a state where logically things should work but I still end up getting an error when I try to run a simple VISA Open command (see attached screenshot).
The initial problem I had was I was not able to acquire a VISA resource that opens a session to my PCIe board...it would simply not show up on the resource list. After reading around I discovered I needed to create a custom VISA driver for my board. Once I did that using the VISA Driver Wizard, the device showed up in my list (as seen in the screenshot). I wrote the simplest of all VIs where I simply open that VISA resource, however, the error seen in the screenshot is produced.
I'm pretty sure this is a simple setup issue, but does anyone know what I'm doing wrong?
Attachments:
Screenshot1.JPG ‏145 KB

Hi bonhomme,
I see you're having some issues using VISA. It sounds like you're new to VISA, so I wanted to pass along some information that we have availble on this software. This link gives good general information about VISA, and the related links are extremely helpful in finding specific issues.
Thank you for attaching your error. This is extremely helpful in debugging since we can actually see the numbers. There is another forumn that talks about these at this link and at this link.
Hope this helps you out!!
Lea D.
Applications Engineering
National Instruments

CDC setup problem

{noformat}Dear all,{noformat}{noformat}Trying to troubleshoot a CDC setup problem in ODI:{noformat}{noformat}I got an error when trying to "Start Journal" from the CDC source model (in Designer).{noformat}{noformat}Here is what I've done:{noformat}{noformat}1. grant the following role to the CDC source schema (user):{noformat}{noformat}DBA, execute on DBMS_CDC_PUBLISH, connect, resource, select_on_change_sets, create session, select_catalog_role, execute_catalog_role, create sequence{noformat}{noformat}2. in the CDC source model "Journalizing" tab, specify JKM 9i logminer (CDC source is on 9i) and specify "Automatic Configuration"{noformat}{noformat}3. add a subscriber "SUNOPSIS" to the source model -> Changed Data Capture (Operator successfully run){noformat}{noformat}4. "add to CDC" from source model -> Changed Data Capture{noformat}{noformat}5. "Start Journal" from source model -> Changed Data Capture (Operator run failed with the following errors in the "create Journal" step){noformat}{noformat}
30475 : 99999 : java.sql.BatchUpdateException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
30475 : 99999 : java.sql.SQLException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
java.sql.BatchUpdateException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
at oracle.jdbc.driver.DatabaseError.throwBatchUpdateException(DatabaseError.java:367)
at oracle.jdbc.driver.OraclePreparedStatement.executeBatch(OraclePreparedStatement.java:9119)
at com.sunopsis.sql.SnpsQuery.executeBatch(SnpsQuery.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.execCollOrders(SnpSessTaskSql.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTaskTrt(SnpSessTaskSql.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSqlC.treatTaskTrt(SnpSessTaskSqlC.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java)
{noformat}{noformat}Any idea?{noformat}{noformat} {noformat}{noformat}William Lam
{noformat}

Hi Cezar,
Thanks for following up. Below is from the description tab of the "Create Journal" steps:
LOADING:
select     FULL_TABLE_NAME     FULL_TABLE_NAME
from     CDCSRC.SNP_TMP_TABLE_LIST     TMP
where     TMP.FULL_TABLE_NAME = 'CDCSRC.DEPT'
and     not exists      (
          select     'X'
          from     CDCSRC.SNP_CDC_OBJECTS     OBJ,
               CDCSRC.SNP_CDC_SET_TABLE     TBL
          where     TBL.FULL_TABLE_NAME          = OBJ.FULL_TABLE_NAME
          and     TBL.FULL_TABLE_NAME          = TMP.FULL_TABLE_NAME
          and     TBL.CDC_SET_NAME          = 'CDCSRC.CDCSRC'
          and     OBJ.FULL_OBJECT_NAME     = 'CDCSRC.J$DEPT'
          and     OBJ.CDC_OBJECT_TYPE          = 'JRN_FULL_NAME'
DEFAULT:
BEGIN
     DBMS_LOGMNR_CDC_PUBLISH.CREATE_CHANGE_TABLE(
     owner          => 'CDCSRC',
     change_table_name     => 'J$DEPT',
     change_set_name     => 'SYNC_SET',
     source_schema     => 'CDCSRC',
     source_table     => 'DEPT',
     column_type_list     => 'DEPTNO NUMBER(2) ',
     capture_values     => 'new',
     rs_id          => 'n',
     row_id          => 'n',
     user_id          => 'n',
     timestamp          => 'y',
     object_id          => 'n',
     source_colmap     => 'n',
     target_colmap     => 'n',
     options_string     => ''
END;
The error message from the Execution Tab:
30475 : 99999 : java.sql.BatchUpdateException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
30475 : 99999 : java.sql.SQLException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
java.sql.BatchUpdateException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
Once again, the setup details:
- CDC source is on Oracle 9i
- KM used is Oracle 9i LogMiner
- enabled archivelog in Oracle 9i
- installed logminer by running the 2 sqls as described in the earlier tread.
I need to meet a tight deadline for POC completion and I desparate need some help here.
Thanks and regards,
William

Msi km4m-v xp setup problems

Similar Messages

Maybe you are looking for