MSI KT3V and Barton 2500+ Mobile

I have those two and can't change the multiplier, which seems to be stuck at default 14x.

i can tell you as it uses something like 15 as a default multiplier
you would have to wire trick it
then you would be able to select up to 12.5
if you wanted 13,14, etc you would have to wire mod it to them

Similar Messages

  • MSI KT3V and T-bred 2000+

    Hi everyone!!
    I have bought a MSI KT3V and amd t-bred 2000+....
    My problem is that the BIOS shows CPUtemp: 56celcius and in MB5 it shows 50celcius...
    And I am wondering doesn't a AMD Thourghbred 2000+ go in 1.60v?? My sets a default in 1.65v and I can't get down to 1.60v.... WHAT IS WRONG!!!
    Should I upgrade the BIOS?? What would that help to??
    Please help me!!! ? :D

    1.65v is correct. I would go by the BIOS on the temps as they should be most accurate. http://www.almico.com Download Speedfan. I find most accurate for reading temps.
    56c is a little hot but acceptible.

  • [VIA] MSI KT3V and old Asus v3400tnt

    Simple question....can i use an old Asus v3400tnt on a MSI KT3V ?? I have heard people talking about different volts in the AGP slot....1,5v or 3,3v...but i havent found any answers yet

    Hi
    This video card appears to be 1x-2x agp compliant so give it a try.  I could not find on the internet any instance of where the video card was used in a similar system.
    I did find a lot of complaints about the video quality, especially in 3d environments. 
    Low end video cards are very inexpensive and most of them will be a lot better than the old asus card since it appears to be only a 16meg card that used one of the early Riva tnt based chipsets.
    See attached link for examples.
    http://www.zipzoomfly.com/jsp/ProductList.jsp?ThirdCategoryCode=012203&SortBy=A

  • Problems with KT3 Ultra2 and Barton 2500+

    I have a very big problem.
    I buy new Athlon XP2500+ ty my board.
    KT3 Ultra2 support 166FBS, but AGP and PCI bus is overclock (83/42) and my system is very instabile. Now using 133FBS. Can I fix bus to 166/66/33???
    My configuration:
    Win98SE+WinXPSP1
    MSI KT3 Ultra2 (bios version 5.7)
    Athlon 2500+@1900+ (Barton 11*133, 1,65V)
    + Spire 5F271B1L3 FalconRock II™
    256MB RAM DDR-400 Kingmax (CL2 at 333, 1.7V*)- sorry I mean 2.7V*
    Daytona ATI Radeon 9000 64MB DDR
    SB Live! Value
    AMD 10/100 LAN adapter
    40GB Seagate HDD
    Lite-on combo
    FDD teac
    add: 4 april 2004 at 15:17
    My PSU is Emko 300W ''JS-300 P4''parametres in:http://www.emko.cz/emko_cz/index.html
    1900+ temps: CPU:                          Chipset:2500+ temps: CPU:                          Chipset:At 2500+
    Stability configuration si withount SB Live! value and LAN.
    result:     Memtest86                       - O.K.
                  3DMark2001SE build330    - O.K.
                  SiSoft Sandra 2003           - O.K.(burn-in: CPU and memory test 20time)

    what sandra version did you use?
    next to temps and psu, please tell us, what bios is installed. barton cpus require version 5.7
    "(CL2 at 333, 1.7V)" did you mean 2.7V? cause 1.7V are llittle too low.
    sj

  • MSI KT4V and Barton 3000+ crash problem

    Hi all!
    I recently upgraded my PC (MSI KT4V) with an AMD Barton 3000+ CPU. Before I had a 2600+ Throughbred.
    With my old 2600+ I could run my system stable with a FSB set at 166. It couldn't go much higher that 175 before the system became unstable.
    With my new Barton I have a problem :
    With my FSB set at 166 games like Far Cry and COD crashes. Explorer crashed at sites with Flash content (flash.ocx error report) otherwise no problems. My Pinnacle studio 7 program couldn't render playable movies.
    After I underclocked my CPU, setting the FSB at 154 giving me a total speed of 2GHz, all problems are gone now  
    My system reports a CPU temp at 48 degrees celsius at a 166 FSB setting but could it be a cooling problem anyway?
    I have used Artic Silver as thermal paste on the CPU die.
    I have reset my memory timings to CAS 2,5 even though the Corsair RAM supports CAS 2 to get the most stable system.
    Is the KT 400 chipset up for the job with the increased speed?
    I would like to get the most performance out of my new Barton so I hope that some of you guys can help me out here.
    My system spec is :
    Win XP SP1 and SP2
    CPU : AMD Barton XP 3000+
    Motherboard : MSI KT4V (Bios 1C0)
    Soundcard : SB Audigy 2
    Graphics card : Radeon 9800pro 256
    Memory : 1GB Corsair XMS (CAS 2)
    Power suply : Antec 480W
    All latest drivers installed
    Best Regards
    Basse

    Hi Osnavi!
    48 degrees is an idle temp and about 51 stressed.
    The processor is an Athlon 3000+ 333MHz
    The cooler is a Thermaltake Silent Boost
    I have 2 modules 512 MB Corsair XMS PC 2700 333MHz placed in slot 1 and 3
    I forgot to tell that I ran memtest386 with the fsb set at 166 and I had error reports on the 128Kb L1 cache right away. Lowering the fsb to 154, the memtest came out alright.
    Should I remove the heatsink and reaply cooling paste - silver-free maybe?
    Strange  
    Any ideas are welcome
    Best regards
    Basse

  • MSI KT3V and Radeon 9100

    I have this mobo + graphic card, Athlon XP1700, and i have some sort of compatibility problem. When i install Windows 98se, DirectX 9 and any catalyst newer than 3.2 i've got ddhelp error communicate (always when i close simply tetris 4000 game). I check psu, ram, cpu cooling and card in other computer. In my older computer on mobo Aopen AK72(Via KX133) and Athlon 550 with this same via 4in1 drivers and directx i can use any catalyst without a problem. I change hdd too. Only things not tested are mobo and cpu, but i don't have any other. Does abybody knows what is goin on and how i can solve this problem?

    I think no. Only two, usb update and update for hard disk drive with 2MB cache. Do You think that's Windows 98SE problem?

  • Msi Kt333 woes with barton 2500

    Hi,
    I just got this new processor, the barton 2500 and my computer is very instable.
    I have a Kt333 ultra 2 with bios 5.7 and it worked fine with an athlon xp1800+
    I set up fsb 166 and everything else in auto and It will crash at random in winxp.
    The culprit seems to be accessing the hard disk which is a Maxtor ATA133 7200rpm 60gb.
    In one of the BSOD the file that caused the crash was ntfs.sys
    I am now running the board at fsb 133 just so I can use the computer.
    I have currently installed 1G ram, two sticks of 256m pc2700 and a newly acquired stick of 512 pc3300.
    I have a Gf3 ti 200 128m at default settings.
    What can I do to fix this without having to go out buy more hardware?
    Thanks.

    I don't think the KT333 suports ddr400(3200), the Bios 5.7 you have was to fix the 3200+ barton NOT the 3200 ram, So you can only run the DDR333 (2700) ram
     and should never mix your ram it will cause nothen but trouble

  • MSI 6712 (KT4V) Problem AMD Ath Barton 2500+

    Hi guys , im wondering if u can help me
    ive got a AMD Barton 2500+ running @ 1498 instead of 18XX , ive tried the following,
    Setting Vcore standard to 1.65
    FSB 166 , System does not boot
    FSB 133 , System thinks its a AMD 1900+
    FSB 150 , System does not boot
    FSB 100 , System thinks its AMD 1100
    so now im running 1498mhz instead of 18XX mhz  
    every time i have to reset the bios to make it boot again ,
    My memory = Whitelike 333 DDR 2x 256mb Pc 2700 (single sided)
    My GFX = Chaintech Gf4 64mb AGP 4X
    Running XP sp1a Professional
    Any ideas setting it to 18XX ??
    ive tried all the ratios 11 , 10 , 4 , 12.5 , 11.5 , 13.0 14 , 15 nothing seems to work
    even setted the memory to 200mhz , that didn't work ...
    Any ideas?

    Well Mate - If the temperature in safe mode at the lower CPU Speed is that high then it means at the proper speed the temperature would be high enough to prevent the system from booting.
    And according to what you wrote about the white paste I suspect that your installation of the heatsink is the cause of the problem - which brings us back to the point - have you tried re-installing the heatsink with a thermal pad - not the silicon paste as per AMD instructions?
    Anf if after following AMD's installation instructions to the letter you still have the problem you may have a faulty CPU - but unfortunately you will find that you have voided your warranty if you have used any paste instead / as well as the original Thermal pad.

  • KT4 Ultra-SR (MS-6590) dont work with AMD Barton 2500+

     ;( Please help me any1.
    I have MBO KT4 Ultra-SR (MS-6590) with CPU AMD Barton 2500+ and i have a big problem. System corectly boot only if a select CPU FSB Clock = 100 MHz (CPU Ration/CPU Vcore/DDR Voltage=all AUTO). When a select CPU FSB Clock 133 or 166 MHz, system begin run corectly and after few second turned OFF. I selecting SDRAM Frequency on=AUTO/266/333/400 MHz but not working. My old CPU is AMD XP Palomino 2100 MHz and work fine with KT4 Ultra MBO. I upgrade BIOS with 1.4 version. I change memory module with PQI (PC 2700/256 MB) and JETRAM (PC 2700/256 MB) but is same ":censored: ". System dont work. Bad CPU Barton 2500+? I dont no. Please help me any1.
    My System:
    MBO KT4 Ultra-SR (MS-6590)
    CPU AMD Barton 2500+ (FSB 333)
    Memory DDR Samsung 2x256 MB (PC 3200) K4H56083D-TCC4
    Cooler SPIRE WhisperRock IV+Artic Silver 3
    HDD Seagate Baracuda 120 GB SATA
    PSU Enermax 300W EG301P-VE(FMA)
    VGA Saphire ATI Radeon 9100 (64 MB+TV/DVI-out)
    DVD-ROM Pioneer 120S (16x speed)
    CD-RW MSI CR52-A2 (52/24/52, Atapi)
    FDD Teac 1.44 MB
    Creative SoundBlaster Live! 5.1

    Most of the time, this sort of problems arise because of power suppliy issues.. U have a enamax 300W PSU which is a VERY GOOD PSU but might just be on the line...
    If u can, try swapping the PSu for a good 400 or a 420W PSU.. this might solve your enigma.. I really dont think this is your processor...
    Read this two articles on PSu wrtten by one moderater which will aid in solve in fixing your problem (PSU1 , PSU2 , Troubleshooting Guide )
    Best of luck
    RAsika

  • Overclock Barton 2500 with PC2700 memory

    Using MSI K7N2 Delta L MB.
    Want to overclock Barton 2500 [without and CPU mod].  But, memory is not overclockable.
    Is there a way to overclock the CPU while keeping the memory running at 166/333?
    When I've tried to raise the FSB of the CPU, I can't get the memory clock to stay at 166/333.
    Thanks

    dont run a fsb higher then the memory as its most likely to be slower.
    you can try to increase the speed 3-4mhz at a time until it starts to crash and then you back off 5mhz.
    or buy faster memory.
    you can always raise multiplier.
    im not sure but i think the highest you can go is 12.5 and if you chose higher it goes back to lower numbers.

  • Powers off above FSB of 133 (barton 2500)

    Ok here we go....
    K7N2 Delta ILSR
    AMD (Barton) 2500
    Mushkin 512MB 3200 In the Light green slot
    Enhance 300W PSU
    Fresh Install of XP Pro SP1
    Copper cooler CPU Fan and heat sink
    120MM Case fan
    Big Ass Problem
    First of all when I was installing XP from CD it would get to the starting windows screen and then just power off. The only way to start back up was to unplug the power supply and it would power back up.
    I changed to the Bios to defaults and was able to get XP loaded. (Only running at 1100 on the processor)
    Now when I change the FSB to 166 it will run for about 5 to 30 min and the power of issue is back. I change the FSB to 100 or 133 and it will stay on and I can even use it.
    Could this be a memory issue or a heat issue? It has even powered of in the BIOS screen when I had the FSB on 166.
    Any ideas?

    Afternoon
    Depends what else you've got on your system. My system runs fine with a generic 350W PSU - people will tell you that you need 500w beasts, but hey - Kingmax Memory is supposed to be stroppy with Deltas, but mine's fine The only thing I'd say is that if you've got more than 1 HDD and 1 CD/DVD, then you could do with pepping up the PSU.
    Mine's been running non-stop since I got it, night and day, never hit more than 35C with stock cooling and no case fan, and never locked up. Yippee

  • What have you got out of the barton 2500?

    Lets find out what the barton 2500 can do.
    So far i've got 2326 out of it
    But what have you done?
    Please join in and show what you have done.

    You can see my numbers in my sig too.  
    Take Care,
    Richard

  • I lost an .msi file and cannot do updates, how do i fix the file?

    I lost an .msi file and cannot do updates to my Itunes system, Apple has not been abe to help, where do i find the .msi file or how do i repair the system?  All prior updates to the system have worked, but the latest 10.5.2 will not update due to this lost file.

    Try the following steps:
    1. Go to Microsoft website to fix install and Unistall problems. Click "Run now" from Fix it to remove all iTunes & related installer files:
    http://support.microsoft.com/mats/Program_Install_and_Uninstall
    Be aware that Windows Installer CleanUp Utility will not remove the actual program from your computer. However, it will remove the installation files so that you can start the installation, upgrade, or uninstall over.
    2. You should remove all instances of iTunes and the rest of the components listed below:
    it may be necessary to remove all traces of iTunes, QuickTime, and related software components from your computer before reinstalling iTunes.
    Use the Control Panel to uninstall iTunes and related software components in the following order:
    iTunes
    QuickTime
    Apple Software Update
    Apple Mobile Device Support
    Bonjour
    Apple Application Support (iTunes 9 or later)
    Follow the instructions from Apple article listed here: http://support.apple.com/kb/HT1923 to remove all components
    3. Reboot your computer. Next, download iTunes from here:http://www.apple.com/itunes/download/ and install from scratch

  • MSI Ti4800SE and MSI KT4V motherboard incompatible?

    Yesterday I bought an MSI Ti4800SE to replace a GeForce2. It booted up fine and Windows detected it and installed the drivers. However, on rebooting, the monitor went blank and there was a series of beeps.
    The computer would not start. I tried taking out all the other cards and tried the video card in 2 other computers but all I got was the beeps. I took the card back and got a refund as they had no more in stock.
    Is the video card incompatible with the motherboard for some reason? Did I somehow cause the card to die? Should I buy another or will the same thing happen again?
    Any help would be much appreciated.
    My system is
    MSI KT4V motherboard
    Athlon 2500
    512Mb Kingston RAM
    SB Live
    Network card
    56k Modem
    2 hard drives
    DVD ROM
    Mitsumi CD writer
    350W PSU
    Windows 98SE
    Thanks in advance

    Thanks very much for your advice - looks like I need to spend yet more money then!
    But do you think I damaged the card by not supplying enough current, bearing in mind that it booted OK the first time? Or was it not damaged at all?

  • MSI KT3V + Sound Blaster Live Problem

    Hello Guys
    First, sorry for my english, i'm polish.
    Yesterday I sold my old motherboard (Shuttle AK32A), and i bought new motherboard MSI KT3V.  After instaling all peripheals I install on formated partition Win2000 SP3, Via 4in1 4.45, Drivers for my GF4 MX440, Network Adpater 3Com-SOHO, and sound blaster Live 1024. After this i instal game IGI2, and try play, After 30 s. in game main menu my computer crashes, screen is black, led on monitor is lights on yellow, after this i hear 10 - 20 second music from main menu in speakers, after this time my computer crashes completely, a hear beeeeeeeeep from speaker, and this moment I can only push reset button :(
    I try install many version drivers, from orginal cd, downloaded from internet. And newest version from 1.03.2002. An nothing :( I remove my Live 1024 from computer, and put friend live 5.1, and no changes, computer crashes :(
    My desktop resolution is 1128x864x32 bits 100hz When i try play  Divx movies after 1 - 2 minuts, frequency of my screen automatic swicth to 50 hz. If I try manualy switch frequency to old value (100 hz) nothing hapend, and i only can restart system :(
    When i work on my desktop (Word, IE, Winamp etc.) after 5 - 20 minutes, my system crashes too (yelow LED on monitoir, black screen, same situation) and I can only push reset button. When i remove card from pc, or turn card off in device manager all works fine.
    I upgarde bios to newer wersion (1.8), reinstall drivers, reinstall windows in APIC options turned off, remove network adapter, and no changes :(
    P.S. On old Mothearboard all works fine :(
    Anyone can help me solve this problem. Please
    Grettings Mark
    My Hardware
    MB: MSI KT3V
    Athlon 1700+
    512 MB DDR 266 Mhz
    3Com-SOHO Network Adapter
    WDC60 GB +  8.4GB Seagate
    GF4MX440 64MB InsideTNC
    CDRW Teac 40x, CD LG52x

    Quote
    Originally posted by maesus
    Also set PCI Delay Transaction enabled.
    This was a solution for my problem :-)
    Thank you very much. You have beer from me :-)
    Grettings

Maybe you are looking for

  • Sapscript if statement

    hi, may i know why the if statement doesn't work in sapscript? IF &BSID-BUDAT& GE &RF140-DATU1& xxxx ELSE yyyy ENDIF (where &BSID-BUDAT& = 07.01.2008 and &RF140-DATU1& = 01.03.2008) actually march is greater than january but it still able to perform

  • Error while trying to access data from virtual provider - Technical Content

    Hi,   I am trying to install the new BI 2004s technical content.  I am done with the installation I am trying to display data for the remote cubes delivered i.e. 0TCT_VC11/21 etc. but getting an error: Error reading the data of InfoProvider 0TCT_VC11

  • Print only sheets with comments

    How can I select and print only sheets with comments.  If I have a plan set that is 300 pages long and I make comments on random pages and want to select and print just those pages, how can I do that without manually searching through the document an

  • Mail being deleted when preferences are set otherwise

    Hi, I run a late-2013 27-inch iMac with with OSX10.9.3. Although all my Mail preferences are set to 'never delete', periodically my entire Inbox and Sent folders get completely emptied out, every email deleted. The many emails I have in folders are u

  • CS4 Design Premium Download

    I need to reinstall CS4 Design Premium.  I have my serial numbers but now that CS5 is out I cannot find anywhere to download this suite.  I have hunted the Adobe site high and low and even when you do get a search result that says it is for CS4 it ta