MSI KT4 ULTRA BSR QUESTIONS

I just bought new stuff for my computer
 kt4 Ultra bsr
 AOPEN Geforce ti4200 128mb DVI
 2200 XP CPU (IN A BOX)
 256 ddram 333mhz
so i began rebuilding my computer,
first thing i did was moving the CLEAR CMOS to the right position (by the manual) then it wouldn´t boot, no lights, no fan movement, so i found out later  on the internet that it was wrong, so i put the jumper in the other position as shown in the internet.
 But when i start up the computer now it only shows
1500 XP 1350 mhz, should be 2200 xp - 1800mhz i think.
 but it won´t start with the fsb at 133 mhz. what can i do ????
i have calculated the 5v * 30a + 3.3v * 14 = 196w (dont know what that mean hehe)
i just dont know what´s wrong huff plz anyone help ?

Hi,
unable to run FSB at 133Mhz is either two problem or both:
1. CPU Heatsink did not install properly, thermal grease applied wrongly
2. Power supply does not have enough power
Check both of them.
Your power supply is very weak for today's system. Please consider an upgrade. But don't blindly go for the bigger numbers -- 450W, 550W, survey more to know about the quality of the power supply, especially the +3.3V and +5V rails, which both should supply similar amount of current, ie +3.3V @ 35A, +5V @ 36A for a good 400W. For more insurance, go for the well known brand. But usually they cost more.

Similar Messages

  • Msi kt4 ultra bsr

    hi,
    i'm new at this forum.
    i have buy a msi kt4 ultra bsr board whit amd xp 2200 cpu.
    twinmoss pc 3200 memory @ 256mb.
    after install the hardware it seems to run only at xp 1500 in the bios.(amibios).
    normaly you can set the range on 100mhz or 133mhz.
    by this board we can set it only @100mhz and not at 133mhz.
    have olso tryed whit pc 2100 / pc 2700 @133mhz.
    still the same probleem,no 133mhz possible.
    when i put the memory in my msi kt7pro2-ru board it runs at 133mhz only the pc3200 can run on that board.
    is it possible that a little bug in the ami bios the problem is?
    have look at the msi website for a patch but nothing.
    have someone had the same problem.
    regards jupliner / belgyium

    hi,
    still the same problem
    today i have olso buyed the xp 2000+ cpu.
    put it in the bord and haved here olso the same problem.
    in the bios hey run at xp 1250 mhz and not xp2000.
    have buy olso a new psu it's now 450w.
    olso buyed new ram from apacer pc 2700.
    we have tryed everthing in the bios to put it on 133mhz.
    in the bios isn't not possible to set 100mhz to 133mhz.
    when we change the fsb clock higher than we need to reset the bios.
    in the dram timing control we can not set the 100mhz to 133mhz.
    the current host clock is 100mhz and not changeble.
    regards jup

  • Raid & KT4 Ultra BSR

     ;( Can anyone save my sanity!
    Read all about updating PC,  thought easy, I can do that. During summer fitted extra memorey 512, fitted new hard drive, then an extra one for back ups, all well so far, then at Christmas bought KT4 Ultra BSR board & AMD 2400XP. Fitted ok no probs, great.
    So why can't I understand how the hell to get Raid to work. The guide is about as useful as a smack in the mouth. Can anyone point me in the right direction to get an easy to understand guide to which HDD connects where and what I do with the jumpers on each. Tried configuring  as Master and Slave on same cable to IDE 1 works Ok. Then tried same on IDE 3 only MAster shown and cannot configure raid. Please help before I trash it!

    hi,
    i had the same problem,
    i have pull the little white mini plug of the harddisk where you can put it on master/save/..........
    that restarted my compu and in to the set actived the raid / serial controller.
    than you niet to configure your harddisk ( push  ctrl-f)
    and than you use nr.1 (auto........).
    restart and normaly is the job al done.
    jupliner/belgium.
    mb: msi kt4 ultra bsr
    cpu xp 2200.
    256 mb/ddr/333mhz
    big tower
    geforce2
    western digital 80gb/7200(8mb cache)
    liteon 52x24x52
    16/48 dvd

  • KT4 Ultra-BSR - Drive problems?

    Yesterday I purchased a KT4 Ultra-BSR. I am doing a clean install.
    I have an Athlon XP200+, 2 x 512MB DDR Ram (PC2100).
    On IDE1 I have put 2 x 20GB Western Digital HDs.
    On IDE2 I have put a Pioneer DVR-A04 as Master, and a  100GB Western Digital HD as the Slave.
    On IDE3 I want a 30GB Western Digital HD as Master, and a 40x Liteon CD-R/W as Slave.
    I have installed Windows XP Pro (SP1) from new, and I have installed all of the drivers and utilities from the Drivers CD. My motherboard was shipped with BIOS Version 1.1
    When I boot into Windows, I do NOT see the CD-R/W at all.
    Also, the only way ro see the HD that's on IDE3 is when it's configured as an array (even though there's only one HD).
    I would have preferred to have two HD's on IDE3 but NOT with any form of RAID configuration - is there a way of doing this?
    Many thanks

    Quote
    Originally posted by Mastiff
    [QUOTE[size=15]Also dudes, how did you get the Bluetooth to work on the KT4 Ultra-BSR??!?  I'm desperate for help on this!![/SIZE]  
    I did it the simple way: Used Fujitsu-Siemens' Plugfree setup instead of the incredibly buggy MSI drivers. Then it worked perfectly with my PocketLoox and Ericsson T39. The hardware is the same. But still the range stinks (max 20 feet on my system), so I bought a full WLan setup instead.
    Here's the URL (I belive it says it's only for Fujitsu-Siemens' computers, but that's just standard manufacturer's bull.  8)
    Bluetoot-drivers
    And an explanation concerning pocket pc's and the installation:
    FirstLoox-forum
    [/QUOTE]
    You've misunderstood my problem.  I have the MSI KT4 Ultra-BSR motherboard which has a bluetooth module which needs to be connected to the motherboard, however, I don't know how to connect it (PHYSICALLY).
    Therefore I need someone with the same board to tell me how they did it.

  • MSI KT4 Ultra! A little question.

    Hello. )
    I'm very interested, in the new MSI KT4 Ultra, but i've a doubt:
    The pure version of the KT4 Ultra, has a fan on the chipset?
    How many IDE channels come with this pure version?
    Thank you, and sorry about my poor english.  :D

    You can modify de FSB in the bios, but there is a jumper that provides these 3 options, 100mhz, 133mhz and 166mhz. 100mhz for the duron cpu's, 133mhz for the Athlon xp  Palomino and Tbred, and 166mhz for the athlon xp Barton ( not 100% confirmed).

  • Raid BIOS Gone (KT4 Ultra-BSR)

    I recently bought a Serial ATA Hard Drive wanting to install it on the raid controller.  But when I went to enter the Raid Controller's BIOS FastBuild Setup (at boot-time), it never shows up.
    I have the KT4 Ultra-BSR, and I can see the RAID Controller enable/disable option in the Integrated Peripherals.  I have it enabled, but it NEVER  displays the RAID bios at boot-up.  This is the second KT4 Ultra I've had and I know I saw the RAID bios on the first one I had. I have the latest system BIOS installed (1.30).
    Has anyone experienced this and/or know how to fix it? Is there a way for flash the RAID controller to possibly fix it?  Did the entry to the setup change from whats in the manual (ctrl-F4)?
    Any help is greatly appreciated. Thanks

    I've seen a couple other post like yours Shark. While that makes me feel a little more comfortable that other are having similar problems, I thinks mine's a little different.  I don't ever remember seeing the RAID BIOS on this motherboard.  I've tried turning it off and on in a row to see if mine would eventuall show, but I never see it.
    Does anyone from MSI read these? I think something should be done.

  • MSI KT4 ULTRA-BFISR + Ati Radeon 9700 pro = not good??

    Hello everybody!
    First of all, i youst have to say that i think MSI have the best motherboards....
    Here's the problem (i haven't buyed anything yet!):
    I am going to buy MSI KT4 ULTRA-BFISR and ATI Radeon 9700 Pro, but i have read many places that Radeon aint working with MSI KT4-based cards! Im am going to buy an 520W Power (i aint so good in english so i hope you now what i write  :D )
    I am also going to buy 2 x Cosair pc3500 xms ram... Is this one working with the motherboard by the way?
    But my question is: Will the Ati Radeon 9700 pro work with this card? (i must remember to buy the 1.3 version!) I am gonna get my Radeon 9700 pro from USA, how can i now when i order that is an 1.3 card?
    Thank you for answering!  :]

    I think also that even there is two drivers, that is not a reaseon why it isn't work. One time I install only standard VGA drivers, but result was that I got two standard VGA driver.  8o
    First time I try without VIA drivers, then with 4.42 and 4.43 VIA drivers. Result was almost same all the time, it always crash when Nature test start, but this exist also to older mobo (Abit KT7A-RAID). Problem exits few games they lock up or stuttering. Ati demos works fine, but one time that car demo stuttering a lot, but I transfer data at same, so I'm not sure what was reason.
    This moment I don't have possibilities to try Hyperion 4.45 drivers or something else, because it's my friend computer.  
    MSI KT4V 6712 (Bios 1.0)
    AMD Athlon 1.2
    512 MB DDR 333 RAM
    SoundBlaster Live
    ATI Radeon 9700 Pro (Club3D)
    Power 300W
    Realtek Ethernet card
    Samsung 40GB harddrive
    Samsung DVD
    VIA 4.42 and 4.43
    WIN98

  • MSI KT4 Ultra-SR (MS-6590) And IDE3

    Rig is As Follows:
    MSI KT4 Ultra-SR (MS-6590)
    AMD Athlon 1000Mhz  :(
    512MB DDR333 (PC2700) x1 stick  
    MSI GeoForce 4 Ti4200  8)
    IDE1: Western Digital 40Gb 5400rpm (win xp pr) as master & Maxtor 80Gb 7200rpm as slave
    IDE2: Liteon 52x24x52 CD-RW  )  as master & Samsung 12x DVD as slave.
    Soundblaster 5.1 Live PCI
    350w Power Supply
    MSI D-Bracket 2 &  S-Breackets Fitted Also.
    I have Three Questions.
     >My CPU has a FSB of 200, but the bios (version that came with board) shows it as 100 FSB. See here for athlon bus speeds
    Is it ok to increase the bus speed without damaging the processor.
    >The two brackets that i have fitted (s and d brackets) do not work. Why?
    >What are the optimal and settings for my ram (PC2700 512MB DDR) and GFX Card (MSI GF4 TI4200).
    >Oh yeah, my CPU is now operating at a higher temp than before (using old K7VZA ECS Mobo) @ 50-55. Is this normal??
    Sorry for the n00b questions, it's just that this is the first time iv ever taken my PC to pieces and re-configured it myself  :P
    Thanks in advance.   -RjA

    I can help a little  1000MHZ AMD chip=200FSB XP CPUs=266FSB this is CPU speed . AMD 1000MHZ CPU needs to run @100FSB where a XP CPU can run @133FSB This is MEMORY speed . Trying to crank that poor old chip up to anything other than 100 will do you NO good. You need to buy a bigger cpu of the XP kind. A lot of the older XPs can be had for a low price. 50c isn't not super hot. My KT4 runs in the 40s. You might want to think about a bigger cpu cooler to bring the temps down a bit. Most of your settings should be left at system default, since you only have a 1000MHZ CPU. When you go up to an XP then you can make a few changes. Regards BIGDADDY51 :D  :D

  • KT4 Ultra-SR Questions

    Set-up As follows:
    AMD Athlon 1000Mhz Socket A CPU with Coolermaster Fan
                                                                                     512MB DDR333 PC2700 RAM
                                                                                     MSI KT4 Ultra - SR Motherboard with optional S & D Brackets
                                                                                     Liteon 52246S CD-RW (52x24x52)
                                                                                     Samsung 12x DVD-ROM
                                                                                     MSi Nvidia GeForce4 Ti 4200 GFX Card (AGP 4x, 41.09 Drivers)
                                                                                     Seagate Barracuda 40Gb as master on IDE1
                                                                                     Maxtor Diamond Max 7200rpm 60Gb Drive as slave on IDE1
                                                                                     Creative SoundBlaster 5.1 Digital PCI
                                                                                     Creative DTT2200 5.1 Surround Speakers
                                                                                     Enermax CS-305 Black Case with Side window
                                                                                     Windows Xp Proffessional (no SP1)
    A 350w Powerup powersupply (one that comes with the enermax cs-305 case)
    Several Questions:
    Processors/memeory
    I thinking of changing the processor to an athlon xp. With one should i get? And why is that those processors which have the 333FSB are nearly £90 more expensive??? Does matching the fsb speed to your memeory speed increase peformance too?
    Powersupplies
    Is my current powersupply sufficient for my setup?
    Is this PSW any good_ Q-Tec 550w Dual Fan  (that is quite cheap)
    And why is this one much more expensive? Enermax 460w
    Cooling
    using Fuzzy logic 4, the temp displayed is mostly 55-64. Is this too high? And can someone please explian how i find out the full load temps etc.
    GFX Cards.
    I have the 128MB agp 4x MSI GeForce4 ti4200 card running at 250 core/459 clock usign the MSIO clock tab in desktop properties. Can this safely go any higher?
    USB Ports.
    On my M/B i can get the top two ports to work fine, but not the bottom two. How come. I have the bracket installed also with the extra 2 usb ports - does this have something to do with it?
    Thanks in advance.

    1. KT4 Ultra can support upto the fastest XP2700+, you can get it provided you have money... Yes, FSB matching with memory speed the fastest.
    2. Enermax has extra features such as fan-control adjust.
    3. If it's idle, it's high. to get full load, just run some CPU benchmark and loop it.
    4. Your question sounds like "if I buy lottery today will I win?" No comment on the overclockability.
    5. Have you enabled ALL USB PORTs in the BIOS?

  • Kt4-Ultra-BSR & Via 4in1 hyperion all version problem !!!

    PC :
    CPU : Amd Athlon 900 Mhz
    MB : Kt4 Ultra BSR
    VGA : MSI Geforce 2 Ti 64 MB DDR Pro VT
    HDD : IBM DTLA 307030
    RAM : KINGSTON 400 Mhz cl 2,5
    Problem : If I install Via hiperion drivers in all version my system cannot boot and on the screen are Black lines and Microsoft Windows XP logo in boot isnt full = Grafic problems. Can you help me please?

    I dont think so. Because i used this Mb with other VGA and Memory and same problem. But if i dont istall AGP Gart driver from this pack system working correctly. But i want to know whats is wrong. Can i have lower performance in games without AGP Gart driver?

  • Pb ? MSI KT4 Ultra

    Hello,
    I own a msi kt4 ultra motherboard, 512 Mo Ram Twinmos PC3200 and an athlon xp1700+@2012 MHz (175*11.5)
    One day, I managed to boot at 194*10.5 but now, it is very instable with any fsb > 180. Where is the pb ? Is it due to the PCI or the AGP ? (because the coef is still 1/5 nd not 1/6 ?)
    Is it very impossible to succesfully boot at 200MHz with a KT4 Ultra ?
    Other  question :
    I manage to boot with my ram at cas 2-3-2-6-2Ways but not 2-2-3 or 2-2-2
    It is very strange that I can put the RAS precharge at 2 clocks but not the RAS to CAS
    Couls anyone help me ?
    (sorry for my english , I'm french...)

    but its very doutfull the board would run at it
    it only has 1/5 divider so at 200 fsb agp would be at 80 not 66 and pci at 40 not 33
    http://www.amdforums.com/showindex.php?s=&threadid=234282

  • Problem with my MSI KT4 Ultra

    Hi all!
    I have a BIG problem, I have tried to look at this board, but there is many different answers out there  ;(
    I have KT4 Ultra with Athlon XP 2600+
    I have set FSB to 166, and when I startup BIOS says Athlon XP 2600+.
    But in windows system, it only says:
    AMD Athlon XP2600+
    2.09Ghz !!!!
    768Mb RAM
    Why is windows only says 2.09Ghz??
    AND, I think my system is very slow. I used to have AMD 1200Mhz. And this sytem is almost like my last computer.
    My System:
    MSI KT4 Ultra ( MS-6590 ) with BIOS
    CPU AMD Athlon XP 2600+
    768MB DDR 400 RAM
    GeForce 4 TI4200AGP 8x
    80 Gb Seagate 7200 Harddrive

    Quote
    Originally posted by swedecom
    Ok, I use these settings in my BIOS, are they right for my system??
    MY SYSTEM:
    MSI KT4 Ultra ( MS-6590 ) with BIOS
    CPU AMD Athlon XP 2600+
    768MB DDR 400 RAM
    GeForce 4 TI4200AGP 8x
    80 Gb Seagate 7200 Harddrive
    MY SETTINGS IN BOIS:
    Spread Spectrum = +- 0.25%
    CPU FSB Clock = 166Mhz
    CPU Ratio = Auto
    CPU Vcore = (V) Auto
    DDR Voltage (V) = Auto
    Termination Vol (V) = Auto
    AGP Voltage (V) = Auto
    Hope someone can help me out  

  • No optical-out sound on MSI KT4-Ultra!!

    Hi, I have recently set up a system based on the MSI KT4-Ultra board. I'm using an Athlon XP 1700+, a Radeon 9000 video card, and I've installed Windows 98.
    Although all the drivers and audio applications which MSI provided installed fine, and 2-channel audio from the on-board sound chip works great both for music and for the 3-4 games I've installed so far, I can't seem to get the optical SPDIF port to work! I bought a cable and connected the computer to my Sony MD-player and attempted to copy my CDs onto MD. I go into the MSI control panel and check the box to enable SPDIF-out, removing the speaker cable from the analog line-out just for good measure. When I plug the optical cable into my MD it recognises digital input and prepares for recording. I press record on the MD and play on the computer's CD-player app, but the MD LED shows "no signal". I'm pretty sure both the MD recorder and cable are OK since I've used them to copy CDs from a Kenwood portable CD-player quite recently, so it must be the MB that's giving me problems. Indeed, when I've stopped playback in the CD-player app and went back into the audio control panel, I found that the SPDIF box had been unchecked of its own accord. I've tried this several times, and I've unplugged the S-bracket and reinstalled it all over again just to make sure it was plugged in properly, and I still get the same problem. All audio works fine except optical out! Haven't got a coaxial cable or recorder so I can't check if the coaxial port is equally buggered or if it's just the optical, but I'm getting really annoyed here: this was the one feature I liked best about this board and the only one which isn't working! Any ideas, anyone?

    dude, i think i can get u ur signal, but currently i can only get silent recordings, u may have better luck.
    on the minidisc, there should be a switch or button that will toggle synchronised recording on and off, turning it off should get u a signal, but it wont be in sync wiv the cd, ie u cant trust it to form track gaps.
    hope that helps, done flame me if it dont, if i manage to get substance to my recording, i will send u the info just in case.
    take it easy

  • Linux and MSI KT4 Ultra : DVD problems

    Hi, I own an MSI KT4 Ultra Pure mobo.  The vt8235 Southbridge is supported in the lastest version of the Linux Kernel, 2.4.20 . After upgrading the kernel all seems to work fine, but when the system try to initialize my hdc (Secondary master of IDE, a DVD reader DV-5800A from NEC) it locks up with the message :
    hdc: device {Busy}
    hdc: drive not ready for command
    ide1: reset success!!
    and start looping with this message.
    What can I do to get work my DVD Reader? With my precedent MoBo it works perfectly
    Thanks
    Bye

    Hmmm that error used to happen with an older kernel and an ALI chipset. If you leave it long enough does it give up trying and continue to boot? The ALI did this eventualy.

  • KT4 Ultra-BSR multipler & CPU volts on XP2400 dont work!

    Well after several atempts and clearing the cmos several times the multipler dosnt work on XP2400 and when you go to change the cpu voltage from auto it comes up with strange symbols not a voltage to select! so iam stuck at 141fsb and CPU voltage set to auto i can change the FSB only except lower or to 141, why is it asus and epox can change the multipler and we cant on our MSI KT4 Ultra, iam disapointed and who wouldnt be after all others can change there multipler!
    any surgestions would be welcome and i think MSI should address this problem with a bios update and also look at the voltages for CPU as symbols mean nothing to me! ?(

    Quote
    Originally posted by MSIconvert
    Hi, well bluetooth lol, ok load bluetooth software from your instalation cd rom, dont load the mobile phone software as it causes trouble, then all i did was load the nokia pc suit that came with my nokia 7650, turned on blue tooth on my phone and then asked the phone to find bluetooth, problem it couldnt, but my pc found the phone, you have to make up a password and identify yourself over the blue tooth network, the software says it will conect auto, but it dosnt, you have to conect the 2 devices manuly every time, its faster than cable conection, but one problem i have found is that disconecting can cause problems, 1 out of 5 times when you disconect your pc loses the bluetooth conection and the only way it can find the hardware again is to unplug the arial device inside your case at the usb plug, reconect and it finds it again, a real pain i gota say, so much so i cant be botherd to use blue tooth anymore as iam fed up of takeing the side of my pc case off to get it to reconize the hardware again, but it does work when its all working and the usb finds the hardware, i hope this helps just a little but its not so easy to set up and the software isnt that easy either, maybe an update in the future will make it easyer to use.
    matt 8)
    Oops, I meant how did you connect the module to the motherboard??  I can't find anyway in which to connect it directly into the mobo, and I didn't get a cable with mine.  (I still haven't got to the software side of it yet - the hardware has been my prob for the past few weeks, no-one seems to be able to answer me).
    Hope you can tell me how to do it (pref with some pics or something coz I'm starting to think my retailer sent me the wrong board).
    Thanks!

Maybe you are looking for