MSI KT4AV

Hi on the box of a motherboard write that name of mother board is 694T PRO but on Home Everest software name of Motherboard is MSI KT4AV (MSI-6712) (6 PCI, 1AGP, 3 DIMM, Audio). I need lan driver for that mother board?
I have 2 cd's from MSI CD 1CD2

Quote from: BOSSKILLER on 07-November-07, 03:58:50
Please exact ID your mainboard, look here how: https://forum-en.msi.com/index.php?topic=107777.msg798546#msg798546
Have you installed Via 4 in 1, 1st too?

Similar Messages

What's happened to my board? (MSI KT4AV-L)

I have a bit of a problem,
I have a MSI KT4AV-L with a AMD Athlon XP3000+ Processor.
Here's the mail i've just sent to the tech support of where I got the board from..
Quote
Yesterday, I started to have problems with the internal network port - it was not finding the my gateway, however when I tried the exact same cable and router port on my laptop, it all worked fine.
I decided to reformat and re-install windows XP, in case it was a software error, however this still didn't solve it. The basic problem was that I was getting Timeouts - I tried pinging the router and it was a mixture of successes and failures.
I went into the BIOS and changed back to "Default" settings and restarted - this has made matters worse - now my Graphics card is not working correctly and i'm not able to see anything on the monitor at all due to this.
These facts have made me feel that the Motherboard kid is faulty - I also noticed that the XP3000 chip I had was only showing up in windows as a 1.9ghz processor - not sure if this is correct or not.
Do you have any suggestions or can you give me a manufacture contact so I can try and resolve this issue without needing to send it back - I would appreciate a quick reply as I use this machine for work and it is causing me to delay some freelance projects that I am working on.

Hello,
Did they get back to you?
Please make a list of all your components, including the power supply + details of the sticker.
eg,
+12v = 10a
+5v = 20a
XP3000+ is 2.16Ghz
You need to enter the BIOS and set the FSB to 166Mhz.
Press DEL when you turn the PC on or restart,
go to Frequency/Voltage control > press enter
FSB > press enter, change it to 166Mhz. >press enter
press escape, then goto save and exit > Y > press enter
So that is one problem out of the way.
GFX card problem, is your card AGP 4x or 8x?
Now would be a good time to post that list

MSI KT4AV-L w/ Radeon 9800 Pro at 8x Lockups!

I have the latest 4 in 1 drivers, and the latest Catalyst drivers and it seems that whenever I try running 3DMark2001SE it locks up almost immediately. Now if I use SmartGART to lower my AGP from 8x to 4x it runs flawlessly. Though I can't help feeling that there is some sluggishness in the video. I actually think that my old 4x GeForce 3 Ti500 ran smoother! (I had that on a Soyo Dragon Plus motherboard)
System configuration:
MSI KT4AV-L
Athlon XP 2500+
Radeon ATI 9800 Pro
2 sticks of 256Meg Corsair
60Gig IBM Deskstar
Yamaha 24x CDRW
Cendyne (Pioneer A05) DVD-RW
Antec Sonata case with 380W PS
+5v 35A, +12v 18A, +3.3v 28A, -5v .5A, -12v 1.0A, +5v SB, 2.0A

Quote
If you don't have an actual solution, then please don't post. Thank you for your input.
Not a good way to get help.
Welcome to the world of "new" technology, it takes a little time to get it perfected. As mentioned earlier in the thread, 8X has no perfomance advantage over 4X, and 8X is causing problems, that disappear by using 4X. Until ATI and/or VIA can develop a cure, you have 2 choices:
1. Run 8X mode, and live with the problems.
2. Run 4X mode, and have no problems, and no loss in performance.
(Steps down from soapbox)

Help on MSI KT4AV(MS-6712)

hi
i have assembled a pc using......
Motherboard -    MSI KT4AV(MS-6712),
CPU -       AMD Athlon Xp 2200+,
Graphic Card -    MSI G4 MX440-T8X (8895),
Ram -       Hynix 256MB DDR ( ),
HDD -       Samsung 80GB 7200RPM (SP0802N),
Combo Drive -    LG (GCC-4480B),
Sound Card -    In-built,
Monitor -     Samsung 15",
Modem -     Internal (Smartlink 56K ),
PS -       Un-branded good quality,
there are some problems,
1) i am unable to get the pictures on my TV screen,
i dont know how to connect the TV-OUT connector to my TV.
2) my system was showing athlon XP 1500+ before but after i visited the AMD's Forum i got the clue to make it 2200+ by increasing the FSB setting from 100 to 133, now it is showing 2200+.
3) i have seen this line in one thread here in this forum that
(* do not install or uninstall any VIA AGP drivers, including those in VIA 4-in-1 drivers...) , if i should not install this driver then will it be OK not installing this driver...?
4) (KT4V BIOS version 1.7 and above fixes the CRC errors (IDE problems that cause crashes) ) , and i have this new motherboard KT4AV with BIOS v( ) ,
but i am having this problem as the system crashes and hangs or blue screen appears and does not support this harddisk, and i have to use a samsung tool to downgrade the UDMA mode of the HDD to 100 MBPS,
(This program will change the UDMA mode of all UDMA 133-supporting Samsung drives in the system)and the samsung says thatthe cause is...
Cause
This issue is caused when the data transfer rate between the motherboard (or host system) and HDD is erroneously set beyond the maximum data transfer capability of host, 100MB/sec. Under this environment, the host system fails to read data correctly from HDD resulting in unsuccessful OS installation.
Please note that this issue is caused by the incompatibility between the motherboard and HDD(s), not by the faulty Samsung hard disk drive.
Now should i have to use my system at 100 MBPS speed as my HDD supports 133 MBPS...?
5) what is the use of the (IrDA Infrared Module Header: JIR1), how can i use it?
6) and the last question is this board has (6-channel software audio codec ), how to use it? ans i don't have the S-Bracket as i did'nt get it with my motherboard, and i want to use the 6 channel output from my PC , please help me how to use it ...
thanks
please help me ,,,,

1) Not sure, see p. 3.
2) Is pretty normal procedure around here.
3) Who on earth might have written that? But I suggest you enter 'Safe Mode' when installing 4-1 drivers. You had better have them.
4) Not sure, see p. 3.
5) Someone must confirm this, but I think its for remote networking.
6) If you have integrated or other sound card, drivers, cables and speakers there is no problem. See the manual, please.

[VIA] MSI-KT4AV and PC3200 RAM

Hi guys!
I've got an MSI-KT4AV mainboard, an Athlon XP 1800+, and a 512mb 400mhz Pc3200 module. This is the problem: I changed the DDR module from a 512mb 266mhz module to the 512mb 400mhz module; the mainboard has always worked fine with the first type of DDR module, but with the second one, the PC doesn't boot up. I try to change the memory but there is the problem yet. I try also the DDR Module 400mhz on another MSI Mainboard and that mobo function but not the MSI-KT4AV!!!!! I'm sure that this mobo support the DDR Module 400mhz but I don't know why the system doesn't boot up. Another important thing: when I press the power button to switch on the PC, the Display is totally black with no signal but I can clearly hear 3 beeps from the motherboard: BEEP BEEP BEEP silence BEEP BEEP BEEP silence BEEP BEEP BEEP and so on....
Can anyone help me?
Thank you so much for Your reply....

Did you try clearing your CMOS? Look in your mobo manual if you don't know how. That should fix it. :D.
If it still doesnt, put your old stck of memory back in, go into your bios, and look under Frequency and Voltage. Look for Memory voltage/vDimm. Adjust it to 2.7 or 2.8v. Save settings and exit. Wait for windows to boot and shutdown. Then try your new ram again. =D

Help---MSI KT4AV bios BUG ?!

Hi....(excuse my bad english... ) I try...
I have the MB MSI - KT4AV
two days ago , I have buy a AMD CPU 3200 Ghz , 32bit ofcourse, Inside the shop have sayed to me...no problems with this MB !!!
well I try , but I can't go UP 2800+ !!!
I try and Try with BIOS but no result.
I have read with the last BIOS is corretc the right recognised 3Ghz+ cpu...
I have update BUT always thesame.
So I have read arround, this MB can't support CPU uo 3Ghz !... so never 3,2 ...ok..but MY not go up 2,8 !!!!
BIOS setting....and here is the Myseriuos!!!
FSB...I can't select UP 170 or the PC non start , amnd I must reset the cmos/bios!
(200 I can't forget...I can work with 166.....)
MOLTIPLIC. I can set to x12.13 and My pc (166 - x12.13) give 2800
BUT....If i select x14 I became 880 Mhz !!! and if I set x 15 984 Mhz!!!!!!!
Why ?!?!? this is sure a bios bug....

impossible....sure NEVER He take back!!... later I used and Try.... sure I became in the...A..!
well IF this CPU is not supported WHY work and to 2800 ?!? work or not work....
and WHY x14 give the IDOT nummer 880 Mhz and x15 980 Ghz ? this is ONLY a BIOS problem.... to fixit!!!
so..I not belive MSI have not to do, with this bios...

MSI KT4AV and PSU FAN connector?

MSI KT4AV has 2 fan connectors: CPU FAN and System FAN. What about PSU FAN - is there PSU fan connector on this mobo? Can I connect PSU Fan to System Fan connector?
LeHardi
Jarek Kus

I've read that PSU Fan is not powered from Fan Connector, but it's only uses it to measure RPM of PSU Fan. RPM of PSU fans is controlled by PSU (Chieftec 360W HPC-360-202 DF). Is amperage so important in this situation? Sorry, if it's lame question but I don't know too much about PSU's. ;-)
LeHardi
Jarek Kus

MSI KT4AV 4 RED LEDs WON'T BOOT

Hi. I recently purchased a new MSI KT4AV motherboard, new AMD Athlon 1.33 Ghz CPU, and new PC2100/DDR266 DIMM RAM, and when I turn it on, all 4 LEDs on the diagnostic bracket light up RED (meaning processor failure). Does anyone know what could cause this?
My system specs:
MSI KT4AV motherboard
AMD Athlon 1.33 Ghz 200 FSB CPU
PC2100/DDR266 DIMM
420W PSU (+3.3/28A, +5/40A, +12/18A)
Hopefully that's enough to diagnose any problems because it won't output any video, just 4 red LEDs on the D-bracket.
Thanks.

Hello,
When I bought my second KT4AV, I was planning on using an Athlon T-Bird 1.4 I had laying around in it. It had the exact same problem as you are having, it just didn't work. I then tried a Palomino 1700+ I had in a another computer that I knew worked fine - it was (and still is) in a K7T266 Pro2-RU - and it didn't work either.
I was thinking the motherboard was bad but I bought an Applebred Duron 1600, and it worked perfectly! So it would seem that even though they are listed as compatible, the older Athlon T-Birds and Palominos simply will not work. My advice to you, buy an Applebred Duron, or better yet, an T-Bred XP 2000+.
Sorry if that wasn't what you wanted to hear!
-James

[VIA] related to msi kt4av (ms 6712) mainboards

hi! I've got a msi kt4av and a few things bother me!
1 the cpu voltage is higher than I set it in windows: I set it to 1.65 but it goes to 1.675 in reality! this goes for all of the voltage values. anyone got this problem?
2 I'd like to buy a new hdd, preferably over 200 gb! on the faq of the board it says that the max supported is 160 gb, but I have doubts it has been updated anywhere recently!
could those of you that have or had this mainboard, help me out a bit? thanks

if a mobo says the max supported HDD size is over 137gb, (eg 160gb) then any size above that (eg 200gb) will work. after the 137gb limit on older boards, the next max size limit i believe is somewhere around 4 terabytes
as for CPU voltage, you should set that in BIOS, and preferably to AUTO, unless you're overclocking and know what you're doing windows utilities don't always read values correctly

MSI KT4AV-L and DDR400

I have a msi kt4av-l mobo, a 512 stick of ddr400 and a athlon xp 2600+ running at fsb 166. the memory stick is only stable when i make it run at 266 mhz, 333 and 400 causes random reboots. so i wonder if anyone can help me get my memory to run stable at 400 like it´s supposed to do

Hello,
You can either overclock the CPU FSB to 200Mhz to match the 400DDR memory,
that will make the memory run at its full potential.
Or
Leave the CPU FSB at the default speed, 166Mhz and underclock the memory to 333DDR.
That way you will get the best system performance possible. You should not overclock the CPU.
Please note that the memory can only run at its full potential if the CPU FSB is the same, 200Mhz FSB and 400DDR memory.
And as you do not have a 200Mhz FSB CPU, running the memory at 400DDR or 333DDR is the same. Due to the CPU FSB.
Did SPD work?

Msi kt4av problem - overlay??

Hi,
I can't get rid of a very serious problem. I have bought a MSI KT4AV board together with AMD Athlon XP 2500+ Barton processor and ATI Radeon Graphics card. I get very weird things on my screen every time I want to play a movie or see a picture in the standard Windows XP picture browser. I don't see any JPEGs in IE either. I thought the reason for this was the incompatibility between the ATI card and the VIA chipset and exchanged this board for MSI nVidia GeForce FX5200. I also changed the motherboard with another piece of the same type but the problem still remains. To give an imagination of what happens: http://www.volny.cz/smudlicek/screen/screen.jpg . I am a little bit desperate. I don't think the problem could be in the processor I am still suspicious about the board. Any clues??? Thanx
Maacek

Quote
Originally posted by Fredrik Åsenius
4in1 drivers installed properly?
Changed anything in BIOS?
If it is mostly jpeg, I would check the file association. In my system there is no program assigned, /Explorer/Map alternatives in ME and in Swedish).
It doesn't display jpegs well on webpages. The 4in1 drivers are installed, BIOS unchanged. File assosiations are for sure not the cause for this problem.

MSI KT4AV no boot issue

I'm having a heck of a time getting my computer to boot back up I get 3 long beeps. This does not match anything I've found for codes. I went back in and installed the D-Bracket 4 LED diagnostic bracket.
This "normally" should show 4 red LED's on boot up. I get 3. The number 1 LED is dead, nothing showing. It then goes to number 2 and 4 red and number 3 green. It stays there and goes through the 3 long beeps.
Is it RAM or is it memory ???
anyone know for sure ??

Well, I was going to post all teh specs...but. I was getting pretty frustrated with it when I "re-set" the power switch on the back of the PWS. I'm running an ANTEC Sonata box and PWS. When I turned the switch off and on at the back I was able to boot up to a point.
I had jumped the CMOS earlier thinking it was the problem. So I had to go back through and reset all the setup config...that done it works like a champ again....
I had reset the Vcard and Memory, no help. I had a guy at a computer store tell me the 2 sticks X 256 were not compatiable and that was causing the trouble. He was a little perplexed when I told him it had ran like that for months....He did want me to bring the box in so he could fix it....wonder what that would have cost ?? I guess if you replace enough parts it will work...
Bottom line : 3 lond beeps with a MSI KT4AV board VIA chipset and ANTEC PWS try turning it off and on at the back...worked for me.
Never was able to find an actual listing for those 3 long beeps...

Msi KT4AV with AMD ath. 2500

hey hello there
Here is my question I m planning to buy msi 6712 KT4AV with amd athlon 2500 (333mhz 512 kb)
bios update 5.1 run ok
but Athlon(tm) 2500+ see
what is my problem ---->(tm)can't see athlonXP 2500+
my english language small

okey tomorrow
because goto my house tomorrow
my office now

Msi KT4AV with AMD ath. 2500 (333mhz)???

hey hello there
Here is my question I m planning to buy msi 6712 KT4AV with amd athlon 2500 (333mhz 512 kb)
Is mainboard a good choose??? Can I overclock it and run like 2400-2500 mhz...
please help me because 1 m Planning to buy it today..

Hi........
Hope its not to later..........
The KTV4A is the newer version of the KTV4 with the only real change being the 400A chipset on the newer board, as for overclocking this and its earlier brother were made for it with settings for the cpu range from 100-0299
If asked I would say go for the earlier version as this board does not have the issues that the newer board appears to be suffering (KT7A anyone?).
Hope it helps
Spunkmyer

Msi kt4av-l motherboard re agp?

This is probably a stupid question, but could anyone tell me if a Sapphire Radeon 9250 128mb 8x agp card would be suitable with the above motherboard?
I can't list my full details about my pc as I am in the process of replacing everything and building anew.
Any help would be appreciated.

if that board has an AGP slot, then you can fit any AGP card in it (apart from the really old AGP 1x cards of course )

MSI KT4AV

Similar Messages

Maybe you are looking for