Msi kt6 delta lsr temp problem?

i have just installed a msi kt6 delta lsr , but when i have ran the system a while the sys temp is around 40-42 c and the cpu temp is around 52c .
on my old mobo the temps never went above 35c for the cpu and 25c for the sys temp .
my specs for old mobo etc =
AMD Athlon(tm) XP 2600+
jetway v400db (kt400 chipset)
400w psu
ata133 80gb hd (maxtor)
512 ddr333
geforce fx5800 ultra
windows me (but same in win xp pro)
2 fans blowing air into case and 2 sucking air out
does anybody know a way to improve the temps please

Yippee! A ME user, like me! You know I guess MS support for W98 and ME has been prolonged til 2006? It has partly to do with Linux.
The temperature for the CPU is a little high, but not alarmingly so. Barton gets a little bit hotter on these boards, and I think it is the placing belovw the PSU that is the cause. The system temperature for you is no problem.
To get the warmth away from the CPU I suggest a fan placed in the case door/side, that sucks it out.
Perhaps you have not got such a case door? Then I suggest a quiet 80 mm fan on the back of the case as high as possible, again sucking air out in order to make a nice air flow. Another suggestion is to tie away cabling to the sides of the case as much as possible, power cables, IDE cables etc.

Similar Messages

MSI KT6 Delta LSR SATA to PATA High CPU Usage Problem

Well recently I've switch to my one of my other motherboards on my network to a MSI KT6 Delta LSR, it was working fine after a reformat, but I notice a few problems and that is 100% cpu usage for SATA to PATA, and vice versa, which seems really crazy. Then my network card performance is ISDN speed sluggish, and I tested my line to be working 100% with another mobo. But when I put another NIC on the same mobo it suffers the same speed problems.
Any suggestions? The rig is specs:
Barton 2500+
Antec QuietPower 350W
200GB Seagate SATA HDD
40GB Seagate PATA HDD
ATI Radeon 7500 AIW
Audigy 2 Value
Realtek 8139 NIC
MSI KT6 Delta LSR Mobo
2x512 MB PC 2700 RAM
Pioneer 107D DVD Writer
LG 16X DVD-ROM
56K Modem (A-open)

Shouldn't say what I don't know about SATA, but since I found below, I need ask if VIA 4in1 drivers are installed, preferably while in SafeMode I say:
http://www.google.se/search?q=cache:X6ewgPiIHYcJ:www.qdi.nl/cgi-bin/bbs/YaBB.pl%3Fboard%3DP4I865%3Baction%3Ddisplay%3Bnum%3D1074174096+sata+to+pata+cpu+usage&hl=sv
I recently installed 160g Seagate barracuda 7200.7 drive on SATA port. (I enabled the Bios using Auto) I have a P4I865pea-6al mother board, with two PATA drives . When copying files between the PATA drives on ide ports, to or from, the SATA drive, I notice the CPU usage goes up to 100%, but when copying files from one ide drive (the PATA drives) to another the CPU usage is very low.
Is there a bios setting that will allow me to copy files from the SATA drive to the Pata drives using a small amount of CPU power, found when just copying between the Primary and Secondary IDE drives? I am using Adobe premiere pro, which uses a lot of CPU power, and the high CPU usage of the SATA drive crashes this program? Any help would be appreciated
Re: CPU usage with SATA drive?
« Reply #1 on: Oct 30th, 2004, 7:17pm » Quote Modify
have you installed the newest chipset- and ide drivers ?

Sata on the MSI-KT6 DELTA LSR

Hello
Can someone tell me if i can run 1 sata disc with windows XP and no ide hdd wil this work on my MSI-KT6 DELTA LSR motherboard.
Or do i need to do it in raid
Greetz sjoerd

It's possible. There's one person who's had problems and there's others that say they can. The FAQ on the ASUS KT600 board says you can on XP (not sure about me or 98), so accroding to them the 8237 bridge should be able to. I'll paste the Asus steps which should be about the same. You need to up date your bios to the one ending in .52 (for MSI). Via has some newer drivers posted Sept 22nd ...maybe go with them at link below and follow the asus steps for 1 HD. Post back if it works. I'd use XP with SP1 incorporated. I'm not saying the answer to your question is a definite "yes".
ASUS FAQ site:
I have only one HDD, but it's SATA HDD. Can I use it to install Windows XP on A7V600 without building RAID?
Yes, you can install Windows XP with one SATA HDD on A7V600.
Please first copy the driver from A7V600 support CD \Drivers\VIARAID\DriverDisk\SATA\*.* into root directory of floppy disk.
(i.e. root directory of floppy disk should contain \pide and \sata folders, txtsetup.oem and vt6420 files.)
Then, boot system by Windows XP installation CD, when the below message show up, press "F6".
"Press F6 if you need to install a third party SCSI or RAID driver"
Then, press "S" to specify additional device when next screen show up. Put the driver floppy disk you made and press enter to continue.
(If the floppy disk is made successfully, the installation program will ask for selecting driver. Please then select "VIA Serial ATA RAID Controller(Windows XP)".)
After SATA driver loaded and Windows XP can recognize SATA HDD, you can continue to install Windows XP as usual.
(If the driver is selected successfully, but the installation program cannot find your hard drive. Please check whether the hard drive is connected correctly both SATA cable and power cable.)
Via has some new Sep 22nd drivers (you might try those) and in the notes it says it does JBOD along with RAID.
http://www.viaarena.com/?PageID=310

HELP - MSI KT6 Delta-LSR

hi,
i have this motherboard: msi kt3 ultra2, and now im buying a new one, for use with my barton 2500+.
i prefer MSI KT6 Delta-LSR, but i dont know if can i change the multiplie like in Abit NF7-S (MaxFID™ Technology).
can i do this on MSI KT6 Delta-LSR ?
remember: in actual motherboard i can change the cpu ratio only to 12.5
i need to select what ratio i want. like 15x, 16x...
thanks and sorry for the english.

a its a via board not an nforce
b why change it if you want multipliers like that ,only reason to change is to run 200 fsb and you only get yto do that with lower multipliers

MSI KT6 Delta-L sound problems

Hi, I have an annoying problem. My sound gets disorted and after one or two seconds I get a Blue Screen..
This only seems to happend with Operation Flashpoint Resistance and Lock On Air Combat (both uses a lot of memory). Computer is rock stabile unless this.
I have tried both Win2k/XP and flashing my BIOS to the most rescent one, as well as the drivers.. I have also tried without the PCI-cards, and disabled some features at the motherboard, but with no help.
But when I used Via AC97 drivers instead of C-Media, it crash no more (aswell as no sound drivers at all), but I have no surround sound (I suppose that driver don't support my sound chip fully)...
Ok, know to my specs,
AMD XP 2500+ Barton 512 kb cache
MSI KT6 Delta-L
2 x 512 MB Twinmos Twister CAS2 400 MHz
Powercolor ATI Radeon 9800 Pro 128 MB
Q-Tec 450W Gold
Avermedia DVB-T Digital-TV-card
Promise UltraTX2-100
And some harddrives

:biggthumbsup:First off see if your ram is compatible Here then what is your power supply AMP'S like?
as well we can try this Page to get a stable start
see how that goes,
post back

MSI KT6 Delta LSR and Radeon 9600 XT 256mb x8 AGP Problem

hi,
Ive just brought a Radeon 9600 XT 256mb and it wont run at x8 agp at all, games lockup as soon as i start them, within 5 mins all text on display corrupts and i get a message saying the gpu recover has set the gpu to default settings.
I cant change anything in BIOS to set it to x4 agp as its not selectable and says AUTO only for agp speed setting.
Only way to alter is goto smartgart in ATI drivers and select x 4 agp if u get in before text corrupts :(
Ive managed to get it stable at x4 agp now through smartgart.
BUT it says on box and in manual this motherboard supports agp x8 but why dont it run it ???
i havent a clue whats up with it.

hi,
Ive got it running stable in x4 agp and found a post on ATI website about some motherboards not working proberly at x8 agp with Radeon 9600 series graphics cards.
http://mirror.ati.com/support/infobase/4219.html
Got nice scores in 3dmark 2001 and 3dmark 2003
But what confuses me is Quake 3 demo that didnt change at all over my old card and radeon 9000 pro i tried once too.
I got
174fps with Radeon 9100
175fps with Radeon 9000 pro
173fps with Radeon 9600 XT 256mb
Thats on Athlon xp 1700
strange or what ?
oh well its a old demo anyway but main thing is big increase in 3dmark 2001 by over 2000 marks

KT6 Delta LSR FSB problem solved!

Here's some FYI for anybody with boot up troubles. A friend made a suggestion that got me thinking the dividers might not be set quite right on my mobo so I decided to raise the FSB to 210 and it solved my booting problem. I've tested this out several times and it definately works. Instead of trying to run 11 X 200, I'm at 10.5 X 210 and scoring great:
Anyone having troubles might want to try this out. Good luck.

Hahahaha,
Sorry a bit dutch....stuff happens....all other software running
My Opteron 1.4GHz beats that hands down:
SiSoftware Sandra
Breekpunt Int Buffered iSSE2 (Integer STREAM) Resultaten
Opdracht : 3216MB/s
Schalen : 3360MB/s
Toevoeging : 3348MB/s
Triad : 3334MB/s
Data Item grootte : 16-bytes
'Buffering' Gebruikt : Ja
'Offset Displacement' Gebruikt : Ja
Bandbreedte Efficiëncy : 414% (geschat)
Breekpunt Float Buffered iSSE2 (Float STREAM) Resultaten
Opdracht : 3194MB/s
Schalen : 3334MB/s
Toevoeging : 3343MB/s
Triad : 3330MB/s
Data Item grootte : 16-bytes
'Buffering' Gebruikt : Ja
'Offset Displacement' Gebruikt : Ja
Bandbreedte Efficiëncy : 413% (geschat)
Test Status
Geheugen Gebruik door Test : 255MB
NUMA Ondersteuning : Geen
SMP Test : Geen
Totaal Aantal Test Threads : 1
SMT Test : Geen
'Dynamic MP/MT Load Balance' : Geen
Processor Affiniteit : Geen
Chipset 1
Model : Micro-Star International Co Ltd (MSI) Apollo K8HTB CPU to PCI Bridge
'Front Side Bus' Snelheid : 1x 200MHz (200MHz data rate)
'In/Out Width' : 16-bit / 16-bit
Maximale Bus Bandbreedte : 800MB/s (geschat)
Logische/Chipset 1 Geheugen Banken
Chipset 2
Model : Advanced Micro Devices (AMD) Athlon 64 / Opteron HyperTransport Technology Configuration
'Front Side Bus' Snelheid : 1x 200MHz (200MHz data rate)
'In/Out Width' : 16-bit / 16-bit
Maximale Bus Bandbreedte : 800MB/s (geschat)
Logische/Chipset 2 Geheugen Banken
Bank 0 : 512MB DDR-SDRAM 'Registerered' 2.0-3-3-3CL 1CMD
Aantal Kanalen : 1
Snelheid : 2x 127MHz (254MHz data rate)
Breedte : 128-bit
Maximale Geheugen Bus Bandbreedte : 4064MB/s (geschat)
Mogelijkheden
MMX Technologie : Ja
SSE Technologie : Ja
SSE2 Technologie : Ja
SSE3 Technologie : Geen
EMMX - Extended MMX Technologie : Ja
HTT - Hyper-Threading Technologie : Geen
:hypecrite:

KT6 Delta LSR Ram problem

Hey guys,
Just making a post on behalf of m8, Basicley he's got a sempron 2500+ and kingston ram that is tested as ok in the Test Report book. however we are getting a d-bracket error of light 1 = red, light 2 = green, light 3 = red, light 4 = red. we also get 3 short beeps. We've tryed other ram in the machine but still get the same probs. The mobo and cpu are brand new. any ideas on what procedures to take next????

I don't mind, really. Excuse me for being so stubborn, also, but people come in all shapes.
You had another very good idea, Dr Stu, about the graphics card. It is hard to say where D-bracket finds its POST errors. The first 64kb I think has to do with loading/holding BIOS "drivers"/wakening the BIOS controlled hard ware, and that would be why the POST sequence checks it, but I can't guarantee this.
As stated it would be nice to know the PSU specs. This board relies heavily on the 12V, and even if you successfully post, your system would be crippled without ca 18A on the 12 volt line.
On some occassions POST has been successful by removing all unnecessary parts from the mobo, and running it outside the case. Just to POST you wouldn't need mouse or keyboard or USB devices or PCI cards etc, and hardly even the monitor.

KT6 Delta Fis2r temp problem

The bios says that my xp 2400+ is burning (75C), but that is just not right. I have a Zalman 6000 CU on it, probably a bug in the bios, or isn't it ??????

I don't get to 54C, but i have it at 59C now, with an extra system cooler.
I'm going to buy a alu case, with an peltier cooler, that will get it cool, i hope.
Thanx

Problem with KT6 Delta-LSR

Hello
I bought MSI KT6 Delta-lsr today and haven't had it work yet.
Usually when I turn on the power only fans start to run and i get memory or processor error from d-bracket leds. Memory chips and processor should be ok since sometimes If I clear cmos and start pc, it seems to start fine and all leds are green but system will hang in winxp loading screen. Changing options in bios doesn't seem to do any good, usually boot after editing bios will cause again memory or processor error.
Any idea what is causing this problem?
Specs.
Amd TB 1ghz -> too old for this mobo?
256mb seitec ddr 333 (also tested Twinmos memory chips)
Msi kt6 delta-lsr
Msi gf4 ti 4200
harddrives, cd, cd-rw, the usual stuff...

Thank you for moving this topic to right forum.
I was wondering if those memory chips just doesn't work with my processor.
Could someone explain me this fsb and ddr speed stuff? Not sure if my tb runs
with fsb 100 or fsb 133. Or does those setting even matter for ddr rams?
Manual says that if I have cpu speed 100 and 333 ddr it's not supported but 133 and 333 should work. Still pc sometimes seem to start up but freezes soon. So to me it seems memory and proccessor works.

Problems installing windows on 36.7GB raptor on KT6 Delta-LSR

I've been trying to get this damn thing to work for a few days and then someone told me about the forum here at MSI. So far I've been reading different threads now for a total of approx. 3-4 hours and I don't think I've come across someone with my exact problem unless I've overlooked it. I've had two 40GB drives for a couple of years now and I decided that I'll upgrade to a WD 36.7 GB raptor. I thought all would be good until I popped it in and tried to install windows on it. I boot off the Win XP CD and press F6 to instal the SATA drivers. It accepts the drivers on the floppy, recognizes the drive and reformats and continues until, right after the format it says, "The disk or CD may be damaged......blah blah blah." I don't know if this is referring to my HDD, but it seemed like it was referring to my floppy b/c when I press enter to continue, it asks me to insert the floppy again, and then it reads the floppy and gives the same error. I've been trying to get this to work for the past few days now, and I think I tried almost everything. I disconnected all other optical drives and HDD's except for the Raptor and my dvd writer and still same prob. I tried d/l new sata drivers from MSI and still same problem. I changed where I plugged the sata into (since there were two ports) and still same thing. I wanted to update my bios (v5.5) but the readme file said not to flash from a floppy. I don't have another drive to flash from, so I don't know what to do about that. Please anybody help!!! My system spec are below...
MSI KT6 DELTA-LSR
AMD 3000
1.5 GB RAM
ATI Radeon 9200
WD 36.7 RAPTOR
Samsung 40GB 7200rpm
LG CD writer
LG DVD writer
Enermax 300W
SB Audigy
D-Link wireless network adapter
....I think that's about it.
When I tried installing last the CDRW and Samsung drive were disconnected....

Hello,
I would like to comment on the 1.5Gb of ram.
Please use 1 stick and try again.
Also I hope you are not mixing modules of different make/spec/size.
1GB + 512MB
512MB + 512MB + 512MB <this one is good if thry are all the same make/model/revision
256MB + 256MB + 1GB
You can test the memory with this program.
http://www.memtest.org/download/1.51/memtest86+-1.51.floppy.zip
- Extract all the files to a folder, then run the install.bat.
- It will make a memtest bootdisk.
- Then you must boot from this disk, please test each module individually.
- If they are all fine then try your combo and see what happens.
- Test each module for 1hour, if you get any errors instantly then you can stop and change module.
Do not flash until you are sure that the memory is ok.
HOW TO FLASH BIOS
==============
Download this run it to make a boot disk.
http://www.nerdlabs.org/bootdisks/diskimages/wboot98se.exe
Then get a 2nd disk, copy everything in the BIOS zip to it.
Boot from the RAMDRIVE DISK, start computer without cdrom support.
once its all loaded, put in the 2nd disk.
type
copy a:\*.* c:
press enter
type
c:
press enter
type
adsfi709 a6590vms.570
press enter
it should flash the BIOS.
Then you must turn the PC off and clear the CMOS, (JBAT jumper).
Reconfigure all of your settings.
==============

DDR400 freezing on KT6 Delta-LSR ?

I usually run 2 x sticks of 512MB Kingston DDR400, and have never had a problem.
I've removed them to test a 1GB stick of Kingston DDR400, but it won't work at 'full speed'.
I'm guessing the RAM is fine, as it was working perfectly in the system I pulled it from.
XP freezes (after about 5-10 mins) when I run the RAM at 400MHz, but seems to be ok at 333MHz.
> Tested RAM in all slots, still freezes
> Booted into Windows Memory Diagnostic - no errors
> Booted into Memtest86 - no errors (didn't let it run long though)
> Ran HCI Memtest from XP, and it froze as soon as the test started. But will run fine at 333MHz.
I ordered another 1GB stick a few days ago (to have 2GB total). Have I wasted my money? Will I have to run my DDR400 RAM at 333Mz?
Any suggestions?
View bigger image: http://i35.tinypic.com/2l8x5kw.gif
MSI KT6 Delta-LSR
Seasonic S12 430W PSU
AMD Athlon XP 2800+
1GB Kingston DDR400 (KVR400X64C3A/1G)
MSI GF6200 graphics card
M-Audio Delta 66 audio card
2xSATA HDD, 2xPATA HDD, 1xCD drive, 1xDVD drive

I tried disabling spread spectrum, froze again.
Bugger it. I'll just stick with 333. I'll be getting another one (DDR400) in the mail in a few days, so I'll test that (by itself) and see if it can run at 400. Not that it will be much use even if it can.
I was going to buy 2 sticks of 333 anyway, but the 400s are cheaper. So I guess even if I'm stuck at 333, I've still saved a few dollars.
Nearly time to retire the Delta-LSR I think....

MSI KT6 Delta PROBLEM

First, my hardware :
Everything running @ default speed & settings.
AMD XP 2700+ (running @ about 47C idle and about 55C in work)
MSI KT6 Delta (v2) with latest bios
512mb DDR (333) CL2.5 Elixir
Seagate S-ATA ST380013 (80gb), with WinXP Pro (SP1) installed
Samsung SP1203N (120gb), as primary master on IDE1
Samsung 52/32/52x CD-RW, as secondary master on IDE2
Connect3D Radeon 9600 128mb
PSU Antec TruePower 380w:
+5V 35A
-5V 0.5A
+12V 18A
-12V 1.0A
+3.3V 28.0A
+5VSB 2.0A
I keep getting some strange BSOD. No matter what I do with the machine. Windows locks up completely and after about 1min, that BSOD comes and machine boots.
( http://www.saniainen.com/bs.jpg )
In normal usage, it comes about 1-3 times/day.
Mostly it comes when I copy some files from disk to other.
But it comes everytime when I try to decompress big (over 400mb) ZIP-files.
Everything did work with my old board, MSI KT4A. The problems begun when i changed the motherboard and added the Seagate S-ATA hdd.
I have ordered new memory, Kingston HyperX 512mb (333). Could it be memory-related or something with S-ATA ????
I have tried everything, latest BIOS, latest VIA4in1, memchecks etc...

I had the same problem on a differnt mobo and all I did to fix it was switch the IDE cables around on the devices.
?Give it a try?
It may be a jumper you forgot to change on the IDE devices.

[VIA] Problems with MSI KT6 Delta

MSI KT6 Delta
AMD XP 2000+
256 MB DDR 400
GeForce FX5200 128 MB DDR
I installed WinXP+SP1 and VIA4in1 v4.55 with NVIDIA 66.93 drivers. The screen fades out and in less than a second the picture shows up again.
Note: What should appear in device manager in section "System devices" after installing VIA4in1 v4.55?
I tried: changing video card, RAM memory, installing WinXP+SP2 (worse results!)
Thanks in advance

The system reports no errors nor conflicts in Device Manager window. This problem appeared when I did an upgrade from WinXP SP1 to SP2. I use Fedora Core on the same computer with NVIDIA drivers installed and there were no problems. I tried to change the monitor but it was the same. I think I managed to solve the problem by installing WinXP SP1 and an older NVIDIA driver (version 4.5.2.3) and VIA 4in1 pack 4.55. Everything runs smooth for now.

MSI KT6-Delta-SR + Athlon 2400+ (266) Problem

Hey Guys,
I have a problem with the MSI KT6-Delta-SR and Athlon 2400+ (266).
I've tried about 6 different boards and 6 different athlon 2400+ (266fsb) and what happens is randomly when you turn the computer on the processor is displayed as an athlon 2000+ or athlon 1700+ (using different ram and other components too).
I check in bios and the fsb is still set to 133 (which should be correct for a 266fsb athlonXP).
Running latest bios for the board (v. 5.5) and have tried previous bios revisions.
Anyone come across this? is this an incompatability with the KT6-Delta-SR and 266fsb athlons?
could it be a v.core issue? (what should the v.core b for athlon 2400+ (266)?
Any help would be greatly appreciated.

Borjo jnc, aopen, gtr 350watt psu. it's not a psu problem.
yes 2 problems.
1. incorrect cpu recognition
and 2. random restart before xp loads.
after random restart cpu is recognised as either athlon 2000+ or athlon 1700+
this occurs sometimes before detecting hard drive, but mainly when second bar of windows xp pro loads (running xp pro +sp1 Plus latest updates and drivers. and regardless of what bios revision i'm using.
Tyco cpu id software says athlon2400+ and correct specs when booting properly. if i look at the top of the cpu is says athlon2400+

Msi kt6 delta lsr temp problem?

Similar Messages

Maybe you are looking for