MSI MPOWER Z87 LAN problem

Hello, I have a problem on my MB MSI MPOWER Z87. The problem is I installed the Qualcom Atheros Driver for LAN but the connect doesn´t work PC is reportin no conection. LAN cable is connected to socket in MB and to secket in wall ti network bud on MB it doesnt lighton the LED diods for conection. What to do help me. Thank you in advance

Try this: https://forum-en.msi.com/index.php?topic=178063.0

Similar Messages

(MSI MPOWER Z87) System Won't Start

Hi, a month ago I built for myself a new PC with MSI MPOWER Z87 motherboard.
For a month it worked fine, but couple of days ago, when I tried to launch it nothing would work, OS doesn't start, fans not working including processor fan. All I see is power button button(on motherboard) lit, OC Switch Led lights (one red and one blue) and Clear CMOS (blue) blinking. Debug led doesn't work either. Can anyone help me to solve this problem, what problem do I have and what can I do to fix it?

HuntKey Green Power 550W Sounds cheap and unreliable. Haswell also requires slightly different PSU than older systems did, so if possible test something like Corsair, Seasonic, Antec (and similar with GOOD quality and reputation). You could also go to local PC shop/IT services and ask for testing your system with their quality PSU.
http://www.hardwaresecrets.com/article/Huntkey-Green-Star-550-W-LW-6550SG-Power-Supply-Review/668/10
Conclusion part:
Quote
If you are looking for a true 550 W power supply don't buy this product.
Quote
Take a look on the list of power supplies we already tested and that got an award seal for choosing a good product that won't explode or damage your equipment

MSI MPOWER z87 BSOD on boot in RAID mode

Hello, I've just recently added a harddrive and was attempting to set up a raid and encountered this issue. I have 2 ssds - one is the boot drive, second for games, and I have 3 1tb hdd drives which I was attempting to put in a raid5. I installed the third drive today, went in to the BIOS, switched SATA mode to RAID and got an immediate BSOD before even booting to Windows. Previously, I've had the two ssd in a RAID-0 and never had this issue. The ssd are no longer in a RAID, I was hoping to only have the 3 hdd in the raid5. I'm now having to reinstall windows because the error corrupted a system file somewhere and I'm unable to repair it. Any help would be greatly appreciated.
My system is:
Windows 7-64bit
MSI MPOWER z87
Intel i7-4770k
8gb corsair vengeance RAM
2 120gb OCZ Vertex 3 SSD
3 1tb WD10ezex HDD
MSI GTX760 GPU
Rosewill Capstone 750W PSU

You cannot just change SATA modes.
http://www.overclock.net/t/1227636/how-to-change-sata-modes-after-windows-installation
Note: one mistake or missing step and you won't be able to boot again.

Msi MPOWER Z87 max AC OC to 4.2 or 4.3 guide?

good day. I just bought a msi mpower max AC with a processor i 4670k, I would take it to a 4.2 or 4.3 screen guide or someone who is like my settings to guide me?. Thank you.

Come on Froggy Gremlin, don't tell me you don't love your Mpower? :D
Well its overkill for the average joe and pc enthusiasts, but its a fresh break from all the red and black themes. :D I know its not really a rational reasoning since the Gaming Series are great, but isn't she a beauty?
Sorry for the photos, was taken using a mobile phone.

[SOLVED] Z77 Mpower PCI LANE problem [MSI 7751]

hi peoples i'm a new here as new user of MSI motherboard, this is my first MSI motherboard, and i allready have a problem with it.
as the manual suggest, for a single gpu configuration i should use pci_e2 (page 1-19)
i've tried GTX 260 216sp no go , black screen no system post ,and pressed reset button like 10 time, didn't work, it worked once and never again, and gpu-z shows [PCI-E 16X2.0 @ X4.0]
i've tried AMD 3850x2 no go , black screen no system post
i've tried 9600GT no go , black screen no system post
i've tried 9500GT no go, black screen no system post
i've tried 9800GTX no go black screen no system post
then each of this vga shifted on pci_e5 and worked at the first system startup
is the mainboard faulty?!
PC SPECH :
i7 3770K @ stock speed
Mainboard : z77 mpower latest bios installed
Storage : SSD Crucial 64 Gb
PSU : enermax revo 85+ 1050w
Ram: corsair platinum 2400c9 2x4gb
Windows Xp 32bit
Windows 7 x64 [7601]
i may think this board is faulty isn't it?
the previous mainboard was an Asus Gene Z77 wich didn't give me any kind of problem, cpu ram and psu were the same and worked perfectly.
is there a way to fix this or i should send it back!?
thanks for the help.

Quote from: xmad on 21-October-12, 10:19:28
Remove the board and make sure there are no extra stand off or screws shorting the case.
[cut]
just tried , no go at all ...
Quote from: Froggy Gremlin on 21-October-12, 12:41:50
If you have tried all the applicable suggestions previously mentioned in this thread, try the newest Beta UEFI/BIOS found here;
>> Beta <<
wich one please? i see so many ...
edit: found. i'm trying now.
Quote from: Froggy Gremlin on 21-October-12, 12:13:35
Presume in GPU-Z it was reading 2.0 @ 8X? I think the suggestions are correct. This is a classic behavior of bent or damaged CPU socket pin(s). Could be a faulty PCI-E slot, errant standoff underneath the mainboard, or even a more rare faulty CPU. Uneven mounting or torque pressure of the CPU cooler could also cause this behavior.
what does it mean? should i still have to wait like one month or much more to get a new board since it arrived faulty?

MSI KT4Ultra FIS2R Lan problem

I got an MSI KT4Ultra FIS2R, with an optional GB Ethernet (Broadcom 5xxx).
When I enter the integrated peripherals menu in the BIOS, the LAN device is not shown, and when Windows starts, the LAN device is not shown in the Device manager window.
It is worked fine ~3 weeks before, and it simply stops, and hides...
Why? I bought a GB Lan card, and it is works fine, but it takes a lot of money, and the onboard lan must works, doesn't it?
I flashed the BIOS, with older/newer one, but it doesn't solve my problem.

Have you tried clearing the CMOS?
Something that should be done after every BIOS flash.

MSI K8T NEO Lan Problem

I install XP fresh ones all the time to dry different ways of doing it, but doesn't pick up the LAN for it, Lan is enabled in BIOS and everything, it's just wierd, When i put my Motherboard Driver CD, It doesn't bring up the Realtek Network Drivers.... but get this, I've put a network Card,COZmy onboard lan doesn't want to work, and when i put the cd in, it will pick it up, and show the the drivers to install. BUT I WANT TO USE THE ONBOARD LAN.
I have a VIA K8T800 NOrth Bridge & VT8237 South Birdge Chipsets.
what can be done? the Network is, Realtek 8110c/8110s Dual Layout
Integrated Fast Ethernet MAC and PHY in one chip. I know you'll probably tell me to use the card, but i don't want to :'(
I've tried installing many different drivers. still doesn't work, Need Serious Help.
Regards

What does the device manager say.
What do you mean by not working. Is it installed, is there a conflict, can u ping urself (127.0.0.1).
While ur at it: check the version of the drivers.
Allthough they all should be OK.
You can find the proper drivers here btw:
http://www.msi.com.tw/program/support/download/dld/spt_dld_detail.php?UID=496&kind=1

Big problem with Mpower z87 + I5 4670K

Hi
My English is not perfect so i'll be quick :
Hardware :
MSI Mpower Z87
Core i5 4670K
2x4GO DDR3 2400 1.65V
EVGA 750W GOLD
Water cooling
Ati 7950
SSD Samsung 120GO
So i'm trying to overclock my 4670K but when my frequency is at 4.2MHZ i am obliged to fix my voltage at 1.320V.
If my voltage is under 1.320V and my frenquency is 4.2MHZ i have a boot loop or a BSOD with code : STOP 0x00000124.
Why me i need to fix my voltage over 1.320 V ???? it is to HIGH for juste 4.2 MHZ......
Please help me.
Thx

Quote from: sirap75 on 13-July-13, 20:17:42
Doesn't work. I have flash the bios and try to O/C but same problème : boot loop on windows.
Yeah, 42X on the core worked but with a high voltage (1.300 V). On the internet i have see many tests where users run on 45X with a low voltage (1.140 V) Why i need a high voltage ???? and why when i change the voltage to 1.300 + i have a black screen ?? i am desesperate, first time on MSi fore me.....
Leave the CPU V. on Auto. Use the voltage offsets if needed above what gets set by default. Simply the luck-of-the-draw with Intel CPU's. Mine will do 47X on only 1.18v's, but it cooks itself to death. So the alternative? I set mine to 43X as at 45X, the performance was identical at 43X with less heat and voltage being required. If the board works perfect at auto/stock/default, then it isn't the board.

Debug code 70 , mpower z87

Hi,
yesterday a friend of mine bought the mpower z87 mobo and
everything was fine until today.
The debug leds show the code 70 and the video output doesn't come out.
I'm really desperate and sad for him, I dont know what to do.
The configuration is:
msi mpower z87
i5 4670k
corsair cx750
samsung evo 840
msi gtx 770 lightning

thanks for the reply.. but I knew that the 70 code means Late South Bridge Inizialization
but I didn't know what does it mean .
Anyway we tried with only 1 RAM plugged and the debug code sometimes is A2 (Ide detected) sometimes A0 or A3.
With 2 RAMs the code is 99 (Super IO Inizialization).
We also tried to unplug the video card and the hdd and do the CMOS, with no results .
little update:
the computer now turns on but after 3 mins turns itself off...

MPower Z87 Power connectors

Recently put together a new PC build using a MSI MPower z87, but my power supply (BFG 1250watt - modular) only had one lead for the 8pin power connection for the board. I tried to use a different connector that the power supply had plenty of, a 6pin + 2 pin that was the same size and shape with the +2 connected, but when I attempted to power on, the thinner wire to the +2 portion melted. Did this hurt the board? and Is it safe to run the board with only one of the two 8 pin power connectors connected? (JPWR1 and JPWR2) I do have the larger JPWR3 connected (the one above the SATA connectors).
I'm guessing I'll need to get a new power supply, the BFG one I have is a bit old, from a 2009 build, which may be why it only has one ATX 8pin connector. Can anyone recommend a power supply that defiantly has 2 (or more) 8 pin ATX power connectors?
Thanks

that may have fried the board as a 8 pin CPU power connector has different pins (a live and a ground on the side) but a 8 pin PCI-E power connector has 2 grounds there so you may have blown something on the board or damaged the PSU itself if your unlucky!
try with just one 8pin CPU power connector and and hope to hell you haven't blown something and you lucked out there and haven't damage something (It only needs one unless your using LN2 cooling and doing massive overclocks and huge over voltage's to push the CPU way above its design limits)!
also if you have damaged something and its broke your in a bad position here as you will have voided the warranty as its classed as user error because you made the mistake of convecting that!

Z87 Mpower Max Wifi Problem

Hey!
So I recently built this new PC:
CPU: I7 4770k || GPU: MSI GeForce GTX 770 Gaming 4GB || Mobo: MSI Z87 MPOWER MAX || RAM: Crucial DDR3 BallistiX Sport 2x 8GB || SSD: Samsung 840 PRO Series 256GB || Chassi: Cooler Master HAF XM Midi Tower || CPU-cooler: Noctua NH-D14 || PSU: Cooler Master Silent Pro M2 720W || OS: Windows 7 Ultimate || HDD: WD Desktop Green 2 TB | SAMSUNG SpinPoint 160 GB | HITACHI 250 GB
I'm happy with everything except the Wifi connection... I've been googling and searching on forums without any help so now I'm hoping someone know how to fix this problem...
I got a low connection to the router and it's terribly slow (the router is a WNR2000v2 but I've never had problems with it earlier and I get the same result with other routers). Basically, I get about 20Mbit/s with cable and the wifi from my laptop (HP ProBook 6560b with "Broadcom 4313 802.11b/g/n ") and the laptop can stand right next to my desktop PC and get 5/5 in connection vs MSI Mpower Max Wifi (Intel(R) Centrino(R) Wireless-N 2230) which only get 3/5 in the same distance. I've tried all kinds of placements for the antennas without and improvement. BUT, my problem is that instead of getting 20Mbit/s I only get up to 5Mbit/s. Now... I run the latest drivers from MSI's Mpower Max webpage and I run the latest BIOS (Version E7815IMS V1.3), but I cannot find a solution.
Thanks in advance...
Sincerely,
Dexter
(Excuse my poor English)

I think you should go through some Windows settings. Also try to configure router (this might be the problem).

MPower Z87 - long board start up

Hello,
I purchased MPower Z87 board and after yesterdays assembly I stumbled upon strange board behaviour.
Spec:
CPU - i7 4770
RAM - 2x4GB G.Skill
HDD's - 1x WD EARS 2TB SATA2 - 1x WD EARX 2TB SATA3
SSD'a - 1x OCZ Vertex 90GB SATA2 - 1x Samsun 250GB SATA3 - 1x Toshiba 128GB mSATA
PSU - Seasonic 620W
Problem:
AFAIKT - Debug codes:
9C - SCSI detect
A2 - ATA detect
Long board start up. When I power up PC then I can see debug codes:
9C - 20sec -> 2min
A2 - 2sec -> 5min
So in worst case scenerio board boot up up to 5minutes !!!
NO HDD/SSD - 9C - 20sec -> A2 - 3sec = 23sec to BIOS !!!
This is on 130 BIOS, same on older one that's why I upgraded from 100.
Any idea what can cause this?
Any adivce more then welcome.
PS> Some complains:
I must say that I'm not a fan of MSI at all. I did purchase this board only because sound was better then the one in ASUS ones. My bad and now I regret it because this on my speakers won't be noticed anyways.
6xSATA slot - congratulation on adding to the Mobo L shaped connecters and not streight ones, now I can't connect upper ones when lower ones are used !!!

Well ... I don't know what debug code mean because well.. no entry in manual on this one... so. But that's not important.
Tests, now I see only A2 debug codes (9C is either super fast or not present at all) and time is related to that code:
Legacy+UEFI
SATA3 - boot very fast (SSD Samsung 840 - clean - factory state)
SATA3 - WD EARX (HDD - clean - factory state) - slow (around 5-10sec)
SATA3 + SATA3 - (SSD + HDD - factory state) - very slow
UEFI:
SATA3 connected - boot very fast (SSD Samsung 840 - clean - factory state)
SATA3 connected - WD EARX (HDD - clean - factory state) - very fast
SATA2 connected - WD EARS (HDD - partition data) - very slow
Ok.
That's deal breaker for me, as I won't juggle drives when new ones will be purchase later just to get acceptable boot speed.
In old days (Pentium 1 to 3 times) MSI product were portrayed by me as cheapest one and cr@9ies ones, now only first one changed as it's still cr@9 but cost now much more.
Going to the shop for ASUS one <- that's probably faster solution.
UPDATE:
Sometime when I press power off after some time (5-10sec) PC turns ON automatically, maybe I did turn on some "auto wake" feature - although I have all this disabled.
A2 - on drives still with long wait.

MPower Z87 stuck at A2 when Fanatec wheel connected

Hello,
I've been experiencing a strange issue with your MPower Z87 motherboard, BIOS already updated to the latest version available. Long story short, I have a Fanatec steering wheel
eu.fanatec.com/RacingWheels/ClubSportWheelBaseEU
and everytime I turn on my PC with my steering wheel already on, the motherboard shows the usual codes on my monitor, then get stuck at A2 status without even reaching the MPower yellow and black image. As soon as I unplug my wheel's USB cable, PC runs fine and reaches Windows without a problem.
My configuration is:
Intel Core i7-4770K
16 GB DDR3 RipjawsX 1600 Mhz
Samsung 840 256GB
MSI GTX 780 Lighting
Enermax Revolution 650W
Do you think that this procedure might help? What's strange is that this happens with an Asus Z87 motherboard too, while everything works fine on my notebook, which mounts a Sandy Bridge CPU instead of a Haswell one.
Let me know if you have any suggestions or if you need further informations.

When you update the bios use the method here: https://forum-en.msi.com/index.php?topic=172772.msg1257570#msg1257570
The latest MP bios can be found here:
http://www.msi.com/product/mb/Z87_MPOWER.html#download
I'll be posting the latest beta's this week after I am done being at the hospital so much.

MSI Nightblade z87 question

Would the MSI GTX 670 OC Edition fit inside the MSI Nightblade z87?
Also, the Z87 nightblade comes with a 600w PSU, right?
and, does the Nightblade z87 012-BUS come with the special CPU cooler?
Thanks.

Hi
According to the spec available >>HERE<<:
1. Card is of dimensions: 242x111x38 mm and this desktop: Quote
VGA Support Dual slot, max 290mm lengt graphics
So should fit no problem.
2. Quote
Delicate and Powerful ID
290 mm ATX Graphics Capability
600W 80+ Gold Power Supply
High Efficient Exclusive OC CPU cooler
Supports DDR3-3000(OC) Memory
Super Raid Armed
Easy Assemble
OC Genie Ready
Great Thermal Design with System Fan
Sufficient and Flexible Internal Storage Capability
Audio Boost: Reward Your Ears with True Quality
Killer Ethernet - Kill Your Lag
Military Class 4 - Top Quality & Stability
PCI Express Gen 3 - World's 1st PCI Express Gen 3 Motherboard Brand
So it should come with 600W PSU, yes.
3 and most important: above may not be applicable, as it's mostly dependant on the seller/retailer itself. Ask them if it comes with special CPU cooler, and if it's indeed 600W PSU fitted inside, as it shows as this on the website, but also about this:
Quote
1. The specifications may differ from areas and we keep the right to change without notice. Please check the specific specification with your local dealers.
Alternatively you can ask local MSI office/support: >>How to contact MSI.<<

[SOLVED] Configuring SPDIF for MSI Mpower MAX

Hi people of the Arch,
I would like to play music over SPDIF, while I get no errors, I also get no sound.
I have read the Wiki here Advanced_Linux_Sound_Architecture
Also, I've been Googling and searching here on the forum, I've followed some steps but none seem to 'sound' right.
What I have not done is creating an asoundrc file with my setup, I believe that I can test if it works first, before I create such a file. Like to hear if this is right.
And I should note that I also use regular stereo out and USB headphones.
Attempt to play wav
@ThijsPC .:19:23:. {thijs}>aplay -D iec958:CARD=PCH,DEV=0 booze.wav
Playing WAVE 'booze.wav' : Unsigned 8 bit, Rate 22050 Hz, Stereo
aplay: set_params:1233: Sample format non available
Available formats:
- S16_LE
- S32_LE
Second attempt with bit-rate and new file
@ThijsPC .:19:35:. {thijs}>aplay -D iec958:CARD=PCH,DEV=0 Yamaha-SY-35-Clarinet-C5.wav -f S16_LE
Playing WAVE 'Yamaha-SY-35-Clarinet-C5.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
No error and no sound..
Third attempt with addressing using hw:0,1 and not the alias
@ThijsPC .:19:41:. {thijs}>aplay -D hw:0,1 Yamaha-SY-35-Clarinet-C5.wav -f S16_LE
Playing WAVE 'Yamaha-SY-35-Clarinet-C5.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
No error and no sound..
My motherboard:
MSI MPower Max
Receiving device:
Marantz NR1403
aplay -L
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default
Default ALSA Output (currently PulseAudio Sound Server)
sysdefault:CARD=PCH
HDA Intel PCH, ALC1150 Analog
Default Audio Device
front:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
Front speakers
surround21:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
2.1 Surround output to Front and Subwoofer speakers
surround40:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Digital
IEC958 (S/PDIF) Digital Audio Output
hdmi:CARD=HDMI,DEV=0
HDA ATI HDMI, HDMI 0
HDMI Audio Output
hdmi:CARD=HDMI,DEV=1
HDA ATI HDMI, HDMI 1
HDMI Audio Output
hdmi:CARD=HDMI,DEV=2
HDA ATI HDMI, HDMI 2
HDMI Audio Output
hdmi:CARD=HDMI,DEV=3
HDA ATI HDMI, HDMI 3
HDMI Audio Output
hdmi:CARD=HDMI,DEV=4
HDA ATI HDMI, HDMI 4
HDMI Audio Output
hdmi:CARD=HDMI,DEV=5
HDA ATI HDMI, HDMI 5
HDMI Audio Output
sysdefault:CARD=P780
Plantronics GameCom 780, USB Audio
Default Audio Device
front:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
Front speakers
surround21:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
2.1 Surround output to Front and Subwoofer speakers
surround40:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
4.0 Surround output to Front and Rear speakers
surround41:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC1150 Analog [ALC1150 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC1150 Digital [ALC1150 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 7: HDMI 1 [HDMI 1]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 8: HDMI 2 [HDMI 2]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 9: HDMI 3 [HDMI 3]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 10: HDMI 4 [HDMI 4]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 11: HDMI 5 [HDMI 5]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: P780 [Plantronics GameCom 780], device 0: USB Audio [USB Audio]
Subdevices: 1/1
Subdevice #0: subdevice #0
[edit]
Receiver was broken, replaced, config above is good.
Last edited by Thijxx (2014-11-17 07:55:21)

Try this one, v1.2B8;
https://forum-en.msi.com/index.php?topic=169759.msg1240621#msg1240621
Mine originally came with v1.1 and had no problem booting or restarting problem of holding settings above stock/auto/default.
Quote
What happens is that it will make it past the start orbs and I see the mouse with a black background and then it BSODs. The computer restarts again and then boots properly.
Usually an indicator a voltage isn't high enough. OC settings don't sound stable. Might open a thread in the OC and Undervolt forum section for help with that. I've stayed away from the DRAM Training (left it as is) and reached 2800 without any trouble. Not all IMC's are going to handle that speed though from what I've been reading. All my benchmarks so far are showing RAM speed above 1600 adds little performance value.

MSI MPOWER Z87 LAN problem

Similar Messages

Maybe you are looking for