MSI ms-7529 v1.6 Front Audio!

Can anyone please post how to connect the ms7529 v1.6 front audio to the motherboard? HELP NEEDED ASAP!

More correct, you 're trying to connect 'ms7529 v1.6 motherboard TO the front audio'.
1. check in your manual, does your MB have AC'97 or HD audio.
2. does your chassis have AC'97 or HD audio connector ( or maybe just separate pins?)
http://ask.creative.com/wwimages/audio_int/xfi/xfi_extremeaudio_frontpanel2a.jpg

Similar Messages

MSI 975X motherboard-how connect front audio and mic connection to mobo?

My case has separate connections (not a single molded) plug for Mic and Headset.
Can someone tell me the connections by colored wire perhaps to best connect the various leads to the JAUD1 connection?
Thanks,
Peter

Hi Peter
You might be lucky and discover that someone has the exact same case as you, so they would then be able to tell you the wire colours (If you tell us the make and model of your case). Far as I know, there is no set rule to the colour coding, but you should see a label on the actual wire connector (yes, they are not exactly big, but they do have a label usually!) The manual tells you what each individual pin of JAUD1 is for. The negative wire of each set is usually slightly thicker than the positive. This is all similar to JFP1 and JFP2, for the power switch etc, so I assume you have already developed paper-thin fingers in order to handle these connections
Here is Intel's descriptions of the pins:-
For Intel High Definition Front Panel Audio
Pin Signal Name Description
1 PORT 1L Analog Port 1 - left channel (Microphone)
2 GND Ground
3 PORT 1R Analog Port 1 - right channel (Microphone)
4 PRESENCE# Active low signal that signals BIOS that an Intel® HD Audio dongle is
connected to the analog header. PRESENCE# = 0 when an Intel
HD Audio dongle is connected
5 PORT 2R Analog Port 2 - right channel (Headphone)
6 SENSE1_RETURN Jack detection return for front panel (JACK1)
7 SENSE_SEND Jack detection sense line from the Intel HD Audio CODEC jack
detection resistor network
8 KEY Connector key
9 PORT 2L Analog Port 2 - left channel (Headphone)
10 SENSE2_RETURN Jack detection return for front panel (JACK2)

MSI Z77MA-G45 and front audio header

nice board, nice oc, but the front audio header does not seem to work(rear jacks are fine)
is there a bios setting i am missing?

Quote from: flobelix on 26-September-13, 01:58:46
Do the front USB headers work?
Also try the board out of case and put it on a non-conductive surface. Retry with basic components and see if font audio works if you connect it.

MSI 6712 - Front Audio/Mirophone

Hello Alll
Well got my new case and mods yesterday and it's looking great.
All running fine except with the follwoing problem
I have connected the front audio and speakers/earphones are fine. However I cannot get the front MIC sockets to work.
I have a 6712 (KT4V) Mobo and I have the following connections on the cae, MIC DATA & MIC VCC.
I have currently connected as follows on the JAUD1
MIC DATA --------------- Pin 1 AUD MIC
MIC VCC ----------------- Pin 4 AUD VCC
Any suggestions to resolve would be great.
Thanks
B

Quote
Originally posted by Bagmaster
How many pins does the board have on the JAUD1 and how many pin holes does the front connecter have?
Is the mic connecter separate from the front headset connecter?
If you bought a new case, it should have something on paper that shows the front conecter pinouts for the front audio connecters.
Hello again.
On the JAUD there are 9 pins (but only 8 of which are active).
There are 7 connectors for the front (4 speakers, 1 ground and then the 2 MIC)).
And whilst this case is new, my only complaint is that there is no wiring instructions.
I hope that helps.
Thanks
Branny

Front audio not detected

Hi, I have a msi p35 neo 2 for quite some time now but didn't had the opportunity to use the front panel from my chieftec chase.Today I've tried the front panel but for my surprise alc888 didn't detected nor my headphone or the mic.If I disable front audio jack detection the mic and the headphones work but it doesn't switch off the back audio when I insert the headphones.
How could I solve this issue?
BTW I'm on windows 7rc x64 bit.

Not sure if the drivers are any compatible to Win 7 RC yet.

Fuzzy 945gm2 front audio

Hi,
I have an msi industrial motherboard. It is the min itx mobile core 2 duo motherboard which I use as a super quiet htpc/workstation. I've built my own case etc. and now I want to connect a 3.5mm front audio socket to the motherboard. I can't make any sense of the stuff in the manual about the JAUD1 front connector. I don't think it is the usual one on the other msi motherboards, and I don't see words like right out and left/right return. left out is there in the table on its own, none of the others though.
Can any one help me please?
Thanks,
Shailen.

The Fuzzy 945GM2/945GME2 share the same manual. If anyone can help figure it out here is the pinout for it:
Fuzzy 945GM2/945GME2 manual: http://www.orbitmicro.com/download/resources/MS-9642-Manual.pdf

How to configure onboard Front Audio Pin ?

Dear Sir,
I just have problem with front audio pin connector. My motherboard is MSI 915G Combo. In the manual it's describe as follows..
1. PORT 1L
2. GND
3. PORT 1R
4. PRESENCE#
5. PORT 2R
6. SENSE1_RETIRN
7. SENSE_SEND
8. KEY
9. PORT 2L
10.SENSE2_RETIRN
My Casing has only 8 pins. I already connect pin 1,2,3,5 and 9. It can produce front sound for head phone now but not clearly enought. But my casing has left another 3 pins to connect.
1 is GND and another 2 is for MIC.
So How can i connect it for front mic ???
Can any1 help me .....
with regards,
Joe_Lay

https://forum-en.msi.com/index.php?topic=72497.0

[SOLVED] Front audio panel still not working on K9N Neo V3

I already posted on this here: https://forum-en.msi.com/index.php?topic=113813.0.
I still didn't get front audio panel to work on MSI K9N Neo V3.
Even with my new case; Sharkoon Revenge, it is not working. It wasn't working on my previous noname case too. However, front audio panel on my previous case was working on several other MBs except on this MSI K9N.
Now, I'm using the latest Realtek HD audio driver. I think it's from February '08. Just as with the driver dowloaded by Vista via Windows Update, anything plugged in front audio panel isn't recognized. In this new version of Realtek driver I can't find this Disable front audio panel option so I can't tell if it is checked or not.
Once more, there is not much to do wrong while connecting. Case front audio panel cabel is the same as on all other cases I've ever seen/had. It's a cable with the same number and position of pins as in all other cases. It fits fine on MSI K9N Neo V3. Rear audio panel is working fine.
Any solution to this!?

Quote from: Jack the Newbie on 07-April-08, 03:25:15
From what I can see from the Sharkoon product page, the front panel connectors of your case are not compliant with the Intel HD Audio Pin Standard.
Do you have a manual for your case that includes Pin/wire definitions for the front audio connectors?
No. There was no manual in package. I never thought I will need one either.
Here is Sharkoon Rebel Pin Assigment; http://img176.imageshack.us/img176/9729/pinslk2.jpg
Quote from: Jack the Newbie on 07-April-08, 03:25:15
Have you tried disabling automatic front panel jack detection in the Realtek HD Audio configuration utility? If you don't know were to find that option, access the tab labeled "Audio I/O" and click on the tool icon.
Yes, I tried disabling it. Two tabs (front audio out and front mic) appeared but none of it works.
Quote from: HenryW on 07-April-08, 03:35:46
From something I read: You can also physically check the audio cable of the front panel audio solution. If there is a cable connected to Pin 4, you have an HD Audio module; if there is no cable to Pin 4, you have an AC97 module.
I don't really understand this. Could you please check this on Pin Assignment scan I uploaded above!?

Front audio panel not working on K9N Neo V3

A new problem with MSI K9N Neo V3 MB...
I just found out that Front audio panel is not working (no mic, no line out). I checked the cable 3 times. Seems to be OK. Front panel was working on a previous ASUS motherboard.
- All drivers according to vista are working fine.
- Back panel sound (eveything) is working fine.
- Sound panel says that front panel mic & line-out are not plugged in.
Is there a switch to turn this on? Or maybe some special driver?
Or it is just useless, and working on MB package advertisment only?

Quote from: Richard on 13-January-08, 06:50:13
P.S. Just a thought, I could go get a Ouija Board or Dart Board if you prefer. Might yield some answers.
You sure are funny. No doubt about that.
I do appreciate a good laugh, but in this case laughter won't solve my problem.
This little analogy with a car and a tire is just ridiculous. You know, tire is flat or it is not. Or is it maybe flat only on BMW cars?
I see no purpose in describing cables here, but if this is what would make you happy... It happens that I have few spare mintues, so here we go.
chapter 1. - The Case
I do not know what brand is my case. It's a cheap case with expensive Corsair 550W PSU. Very well cooled. I also don't know what is its name, so let us just call it George.
Here is George roaring on my desk;
Chapter 2. - Jimmy & Gina
This is an unknown brand, no name Front panel cable so let's just call it One eyed Jimmy;
This is local one tooth missing whore called Gina;
Chapter 3. - Encounter 1
Jimmy fills Gina just right. It's very tight but just right;
Chapter 4. - Berta, Gertruda and Mike
Dirty Twins Berta and Gertruda are ready to recieve some massive waves;
Big Mike is ready to give:
Chapter 5. - Encounter 2
It fits right again:
Chapter 6. - Oh NO!!!
It's not working on MSI AGAIN:

Front audio port not working please help..

Hey guys,
My HP Pavilion DV2275ea front audio jack does not work, I have tried many different headsets as the mic jack works just fine. I have tried reinstalling audio drivers (Conexant High-Definition Audio Chip) and still nothing. I have look at the support advice posted to no avail. Is there anything else i could try?
A friend said it could be turned off in the bios but i am not able to get in as i don't know the password for the phoenix bios, could this be true?
Any help will be greatly appreciated

Well from looking at a jpeg of your board the front usb headers are laid out just like my board. Each set of headers support 2 usb ports each. That gives you the 4 in the rear and 4 for the front.
Now as to the pinouts, 1+3+5+7+9 is 1 set and 2+4+6+8+10 is the 2nd set, with pins 1 and 2 being the 5V power pins. Pins 7 and 8 are your grounds. 3 and 4 are the usbo- and usb1-. Pins 5 and 6 are usbo+ and usb1+. Pin 9 is the "key" pin and may actually be missing by intention. Key 10 is sometimes called the usboc pin and normally isn't used. On some boards you don't want anything connected to pin 10, even if you have to snip the wire going to it and terminate the end of the wire with insulating tape.
Your motherboard manual should show you the pin layout.

XFI Fatality And Front Audio Ports On C

Hi guys I have a bit of a question about something that has been nagging me for a while.
I have front audio ports on built into my case that I would like to have working. I know that the sound card came with an I/O Dri've with similar ports on it but it is just bugging me knowing that my case has them also and that they are not working. The case has a headphone and mic jack in front, Problem is that I have no idea if I can even hook them up using the sound card.
Has anyone done this? If so can you help me connect my front ports.
Thanks
Any replies would be appreciated
MarkMessage Edited by mark2887 on 04-22-20072:58 AM

Hi Mark,?This was covered in another thread. http://forums.creative.com/creativel...ssage.id=53474?Creative doesn't recommend this, but other people have had success. To be done at your own risk.

A55M-P33 Front Audio

I know there are lots of questions and answers on the front audio ports. I just want to clarify some stuff. I have the A55M-P33 motherboard which has the JAUD1 connector. My case came with the HD and AC97 audio connectors.
I currently have the HD option connected to the JAUD1 pins on the motherboard. If I decide to use that front audio port, is that the correct option to have connected to the motherboard?
And on another note, if I decide not to use the front audio ports, then is it okay to just disconnect that from the motherboard?

HD Audio is correct to have connected! (AC97 is a old type of connector and some cases have that just for if someone uses a old board that uses that)
If your just going to use the Rear outputs then its ok to not have the front audio plugged in as it will not be in use anyway!

Connecting SB Live! 5.1 to front audio po

Hi!
I have OEM version of SB Li've! 5. that I've bought with Creative Inspire 500 speakers. I also have a case with front audio ports but the problem is that I don't know how to connect soundcard with these ports. I haven't found any info about such possibility in manual but i have only short version of manual 'How to install'. Is there any possibility to connect my SB with the front ports? If there is - how can I do it's
Regards,
vacu
ps.
sorry for my English, I hope you understand me

If you can find a 0-pin socket on Li've! card board, then you can connet your card output internally to the case audio/mic ports by following instructions given @ http://audigy2zshowto.blogspot.com/
NOTE: pin orde may be different on Li've! (instructions are for Audigy 2 Zs, but works well least w/ Audigy 2 card too (I have done this)).
jutapa

What will happen to front audio on computer ca

Hi, When installing a Sound Blaster Audigy Value card the instructions are to disable the motherboard's onboard audio. I currently have front audio from the computer case connected to the motherboard for private listening with headphones. Does it mean that I can no longer use the front audio connectors after installing the sound card?

Sorry but i think your out of luck creative are just about the only soundcard manufacturers who dont have front panel connectors.
Well i suppose they have to sell they're boxes of cheap tricks on the more costly soundcards somehow, if they let you have front panel connectors then no one would buy the higher ranged cards with breakout boxes, not that many do anyway :angry:

Help Connecting JAUD1 to Front Audio on Case

Can anybody tell me how to hook up the following:
Case Front Audio Wires
A - Mic In
B - Mic VCC
C - GND
D - Ear L
E - Ear R
F - Line L
G - Line R
K8NGM2-FID 7207 Motherboard JAUD1
1 - Port 1L
2 - GND
3 - Port 1R
4 - PRESENCE #
5 - Port 2R
6 - SENSE 1_RETURN
7 - SENSE_SEND
8 -
9 - Port 2L
10 - SENSE2_RETURN
I don't want to screw anything up and any help would be greatly appreciated! Thanks and have a great day!!!

Hi Frankenputer,
I'd also like to thank you for such a fast response! I do have a copy of the manual in my grubby little hands and I did read it. That's how I was able to identify the motherboard pinouts in my first post. I guess that one slipped by you . The link you provided is great, it'll come in handy if I ever misplace the manual down the road.
My problem stems from the way the case manufacturer labelled the wires for the front audio connector e.g. using a naming convention that differs from that of the Intel Front Panel I/O Connectivity specification. Specifically the Mic-VCC, Line-L and Line-R wires.
Stated simply, I was hoping one of the experts here might be able to tell me/confirm if Mic-VCC should be connected to pin 3 - AUD_MIC_BIAS or to pin 4 - AUD_VCC, and if Line-R should be connected to pin 6 and Line-L to pin 10 on the motherboard.
Again, thanks for your reply and have a great day!!!
Fred

MSI ms-7529 v1.6 Front Audio!

Similar Messages

Maybe you are looking for