MSI NEO 2 and Gf 8800gt problem

Hi, I have these specific problem. When I upgrade my computer and bought MSI P45 NEO2, I have these problem....
Sometimes in games BUT ONLY IN MENU computer BEEP once and nothing happend for 3-10 sec, after everything fine, but sometimes, fall down to windows and the resolution is 640x480 with these ERROR message. Error Message: STOP 0x000000EA THREAD_STUCK_IN_DEVICE_DRIVER (Q293078)
These Error sometimes happend in windows too, but after few sec everything fine. I tried to reinstall drivers, directX, disable overclock, but nothing change.
DO YOU MAY HELP ME PLEASE??

Quote from: cas on 26-February-09, 06:00:03
You mention you upgrade to a new mobo but then did you did a fresh install of your OS in your hard disk? Alternatively stop overclocking for the time being and run everything in default and see whether the problem goes away
Yes, of course that I reinstall windwos. Hard disk was formated. I try to disable overclock but nothing change.
I got only E8400 3 GBb to 3,6Gb FSB 400.
Overclok of graphic card was 700-750, sharder 1715-1860, memory 920-1040

Similar Messages

MSI Neo i875P FIS2R Vdd & Vtt Problems?!

I have been reading that other Intel 875 chipset Boards like ASUS P4C800-E Deluxe & Abit IC7-Max3 are suffering from Vdd & Vtt problems!!!
Does anyone know if this is the case with the MSI Neo i875P FIS2R boards aswell?
Did anyone follow this up?
Would be interested if this is the case & if anyone has done any mods to their RAM slots.
Thx

No they Dont, and it was only the First revisions of those other Manufacturers Boards That are Really Second Revision i875's, and it has Nothing to due with the INTEL (i875) Chipset, It had to do with a Batch of Bad Winbond Memory Voltage Regulating Chips, that Both ABIT and ASUS Used...MSI does NOT use either that Particular Winbond Chip, or the Same DDR-Power Architecture that MSI employs on their i875P...........Sean REILLY875

MSI x48c PLatinum and Intel E8600 Problem

Hello, I'm from Greece
My computer Setup is:
Mobo: MSI X48C Platinum (bios version 7.0)
CPU: INTEL CORE 2 DUO E8600
PSU: HEROLCHI 525 Watt
RAM: OCZ OCZ3SOE10664GK DDR3 4GB (2x2GB)
VGA: Albatron 8800 GTS
HDD: WD 300GB SATA
The problem is:
I bought them yesterday because i want to upgrade my system.
I connect them all properly in my case and after i turn the PC on it freeze in the MSI logo screen and cant even enter BIOS Setup.
The first time i turned the power on a message like: "Your previous overclockinn atempt was not succssefull. Press a button except del to load defaults and continue." i do what it said and freeze after that message.
This just the first time, the other times it just freeze on the logo screen. Some times it beeps one time and reset by his own and sometimes beeps four times and then reset. The most of the times it just freezes in the logo screen.
I took everything off and reinstall them. Nothing Happen.
I tried with one dimm of RAM each time in deferent positions. Nothing Happen.
I did o clear CMOS from the back button. Nothing Happen.
I perform a clear CMOS with the old method (unplug power, remove battery, wait for a couple o minutes). Nothing Happens.
I believe the problem is with the bios version i have and the CPU compatibility. I look at www.msi.com.tw and it said that this board its compatible with the INTEL E8600 but only at the 7.2 version.
How will i update my bios if my computer doesnt even enter bios setup?
Please help me. any suggestion. I'm losing my mind here!
Thanks you in advance.

Quote from: triangle on 28-August-08, 17:00:43
the only thing i can suggest is to drop in a 7.0 compatible CPU (if you can) and flash the BIOS to 7.2 that way then switch back in your new CPU. A painful process, I know ... Alternatively, if your retailer is friendly they might set it up on a test bench for you and flash it.
Andrew
Like Andrew mentioned, this is the only way out though it is a long painful process.
The other is to get a board that is compatible to the E8600 right out of the box.

MSI 785GM-E51 and memory modules problems

Could anyone help me with one problem. I have motherboard MSI 785GM-E51 and 4 memory modules GOODRAM GR 1333D364L9/2G. But when I'm inserting ALL modules my system not starting (even POST procedure). So working variants - when I'm inserting:
- one module in first (boot) slot
or
- they inserted in first and third memory slots
Any ideas?

It is not motherboard problem, but processor itself - I have AMD Phenom II X4 965 Black Edition 3,4 Ghz Core Revision C2 and this revision (according to the article: http://www.fcenter.ru/online.shtml?articles/hardware/processors/27650#02) has problems with support memory modules DDR3-1333 Mhz more than 2 modules. Conclusion - either adjust BIOS settings concerning memory timings and memory controller voltage or replace this kind of processor with the same type but with core revision C3

MSI Neo Platinum and G.skill Ram

Was just wondering if anybody had this combination (MSI K8N Neo Platinum and G.skill Ram). I have the MSI Neo Platinum. I ordered the processor yesterday (3400 1Mb socket 754) and now I need some ram. I ran across this ram and saw that it had good timings. If anyone has this or has tried it please lemme know how it worked for you and what size sticks you got. Thanks
Karl

looked at the links you provided
specs seem ok nice range of speeds and can run at a nice low latency at pc3200 i.e 400mhz.
should also enable a nice o`clock at pc 4400 specs ie 3.4.4.8 ie higher fsb etc.
than pc 3200 ram
you should be able to run it at fairly low latencies and fairly high fsb sort of half way between the 2.
might well be worth a try you might have found something good there. but then again you wont know till you try it..
contact the reseller and see if you can rma it if it wont run
then you got some comeback if it aint compatable..
keep us informed

MSI P965 Neo-F and a other problem!

Hi alls!
I have a problem with my MSI P965 Neo-F.In fact when i push the power button i have to wait 5-6 secondes for my pc turn on...
I have the same problem that Er.nest:https://forum-en.msi.com/index.php?topic=107722.0 (problem number 5)
My PSU is a Seasonic S12 II 500 W
My config is :
Core 2 Duo 6600 @ 2.40Ghz
2 Gb RAM DDR 667 Mhz Corsair(5-5-5-15 @1.85V)
ATI HD 2900 XT 512 Mb
HD Seagate 320 Gb
Thanks...

ok v1.10 .. so we have same version now.. (maybe it will help us to find somthing helpful)
So (i dont know if you know somthing about..let me to refresh about S3).. S3 is one of two most used sleep modes. S3 (STR) - Save to RAM. It save whole your session to RAM, clear the CPU registrers and turn of all devices in computer one by one... only matherboard is powered by minumal voltage of 5V. This is used to refreshing o RAM and keep content "inside". In this state is consuption of computer avg. 4-6W (...PSU). Ok, my problem is ...
When i want to wake my computer up (a do it by pushin power button) ... somthing (and i dont know which part of my machine).. cause frozen of whole machine. Sometimes i get Windows Vista login window (loggin button fully response to mouse move over), if i want to login windows fall into BSOD or all freeze... somtimes i get only black screen.
So .. it seems to be little bit different problem but we both have problems with some kind of turning on...please, try to describe more about your problem. Espesialy informations about other behavior...
for example ... if you using hybernation (possibly S3), if you turning your computer normal by windows option "turn off", if your problems dissapear when you discharge mobo from static charge (disconect power cord, and push power button), if you have other problem with restarts...
i have same problem like you before i come to v1.9 and higher ... so, maybe its only in some setting i made insensible

[SOLVED]MSI P31 Neo -mobo and strange network problems

I can't get network to work properly with this MSI-mobo's integrated lan chip.
When I boot from Arch install cd r8169-module is loaded and I can get ip via dhcp. Strange thing is that I can access http but not ftp. When I change transfermode to passive from links ftp works. But during Arch install setup I can't access the repos.
When I boot to Arch after install network doesn't work at all. Only thing I get is resolv-errors when I try to use wget or pacman. R8169 module is loaded at boot and Ifconfig shows that I have ip assigned to eth0.
I also tried with 3com's 3c509 network card that I had laying around and I have exactly same network problems with it as I have with r8169.
I am really going out of my mind with this. I have a laptop with via's network chip and I've never had any network problems with it and Arch. I haven't changed anything in my routers setup and I just tried and the networking on my laptop works just fine.
I also tried Ubuntu Hardy on this desktop machine and networking works ok. Ubuntu also loads the r8169 module as Arch does.
Last edited by Aakko (2008-05-18 21:18:29)

Quote from: techie5487 on 24-January-08, 07:34:41
UPDATE:
I tried booting with 2 RAM Chips and it works great! This seemed to be the problem.
The ram IS double sided which would explain it.
If you are wanting some more system specs, just ask and I will try and get the most I can.
Del UK:
If I could run 4gb it would be great but I cannot seem to find the SPD in bios. My BIOS is American Megatrends Inc. v02.61 so it would be great if you could help me with that!
If all else fails I might either just settle with 2GB or buy some new RAM chips. Can anyone please tell me some Ram chips which would be able to give this mobo 4GB?
Thanks
techie5487
Done
2 Gb in
Into bios
SPD off
Set to 5-5-5-15
Save settings
Power off
Install extra 2 x 1Gb modules into slots 2 & 4
Power system up
4Gb detected................. slow post not fast
3.25Gb checked
1 second delay
4096Mb
3.25Gb extend
768Mb in +4Gb
System sees 3.25Gb

K8N Neo Platinum and Maxtor HD problem

I have a K8N Neo Platinum MB with the v1.3 Bios installed.
I have 2 physical HDs:
IDE Primary Master: 120G Western Digital WD1200JB (7200RPM)
IDE Primary Slave: 120G Maxtor 6Y120L0 (7200RPM)
The MB sees both drives in the BIOS, however, in Windows XP, I only see the master drive. The slave drive is not recognized within windows. I tried finding the slave drive with the MS Computer Management application and PartitionMagic as well - neither can see the slave drive.
There is something strange about the BIOS screen.
You can see that the primary master is highlighted (in red). The primary slave drive is visibly but it's not showing properly. You can see that the name of the slave drive is all the way to the left and the "]" character is all the way on right panel, next to "Press [Enter]". The name of the slave drive is wrong. The BIOS is showing something garbled. It looks something like "8t/r 6!128". It's tottaly confused :(
I can even select the primary slave drive:
That's not right!
Pressing enter on the slave drive shows the slave drive (Maxtor 120G) properies:
However, Windows XP will not recognize the slave drive.
I ain't sure what wrong but it appears to be a BIOS problem - why would the BIOS display be so messed up like that ??
I'm not sure what to do. :(

Yea, I'm really mad because not only will this board not recognize my slave driver properly, it may have also killed my X800 Pro video card
I moved my working X800 Pro video card from my old MB to my new one and when I turned it on, the X800 Pro was dead.
I then reinstalled my old MB, hoping it was merely a faulty MB that was the problem, however, my X800 Pro is quite dead now
I'm not sure if it was me who damaged the X800 Pro or it was the MSI K8N motherboard - either way it's dead
My experence so far with my new MSI MB has been horrible !!

K8n neo 3 and radeon 9600pro problem !

ok have anyone have the same problem with radeon 9600pro like me. the card is agp slot and when starting the computer the screen doesent react at all its stay blank. but when putting the radeon 8500 it starts if anyone could say where is the click.... thanks
the mainboard is k8n neo 3 gold

Quote
Make sure in the BIOS it is set to run from AGP, if there is that option.
the bios itself detects if you use a pci express or agp card in the AGR slot, you cant configure it.
Quote
There have been some issues with the 9600 series and 8X agp / agp fast writes.
Try forcing 4X agp and turning off agp fast writes in bios to see if it at least boots for you.
there are no settings like fastwrites or AGP mode. the AGR slot only works with cards which are compatible.
have a look http://www.msi.com.tw/html/products/mainboard/agr/7135agr.pdf
i had luck my card works and is not on this list

P965 Neo-F and GeForce 7900GS problem

Hey there,
I have been suffering a lot from my own-built computer, whose configuraions are:
MSI P965 Neo-F bios 1.60
C2D E6300 1.86G intel
MSI Geforce 7900GS 256M Video Card
2x1G Kingston DDR2 667
Antec 400W PSU
WD 250G SATA II Hardrive
1. In windows XP pro, ALL 3D games share the same problem. display flickers, kindda distortion of the 3D model, 2-D Text in the game shakes, unstable, but game could be going on without freaking out.
2. In Windows Vista Ultimate, Screen goes black and then a message out " Display driver stopped responding and has been recovered", happens very often. and 3D gaming in Vista is totally a nightmare, screen freezed and computer stopped responding almost every time once I runs 3D games.
Somebody told me it is overheated of my system, so I added two fans. The temperatures of CPU and GPU are normally around 30C and 50C which should be fine, I guess. However, problems still kicking my ass.
Is my PSU 400W Antec powerful enough? the minimum requirement of Video Card is 400W.
Would you guys please help me?? I was driven crazy by this unstable issues.

thanks for all your guys' replies.
So far, I have tested 3 Video cards and same problem, so it is not the video card.
I changed 2 PSUs, same problem.
I have tried to cool down the system by all means, and I believe it is not overheated.
I tested two RAM sticks individually, and found that if I used only one of them, no problem.
Therefore, I would say, one memory stick is defective and is repsonsible for the unstablity.

K9N Neo-F and USB Mouse problem

Hello,
Some people including me have noticed problem with USB Mouse when using MSI K9N Neo-F BIOS above 1.3.
Results are simple - when loading Windows, the system initiates USB devices, but when it goes to Windows mouse doesn't work.
There is only one solution to fix the problem, reconnect USB cable from mouse.
It seems to be a BIOS problem, but there have been many BIOSes during 2-3 months and now currently the newest one is 1.63 Beta, which still didn't fix the problem at all.
I contacted MSI, but they can't do anything.
According to my tests, if I change in BIOS S1 to S3, it runs fine until I won't shutdown computer and turn it on again.
I wonder if there's any solution. I'm really mad about it and probably will RMA my mobo or change it to some else.

get devcon (http://download.microsoft.com/download/1/1/f/11f7dd10-272d-4cd2-896f-9ce67f3e0240/devcon.exe)
extract it (from \i386) and copy file to %systemroot%\system32
then copy and paste text in blue below into new .txt file, save it and rename extention to .cmd then execute it.
@ECHO OFF
:: Check Windows version
IF NOT "%OS%"=="Windows_NT" GOTO Syntax
IF "%OS%"=="Windows_NT" SETLOCAL
VER | FIND "Windows NT" >NUL && GOTO Syntax
:: Check command line arguments -- none required
IF NOT "%~1"=="" GOTO Syntax
:: Check if DEVCON.EXE is available and if not, prompt for download
SET DevconAvailable=
SET Download=
DEVCON.EXE /? >NUL 2>&1
IF ERRORLEVEL 1 (
   SET DevconAvailable=No
   ECHO This batch file requires Microsoft's DEVCON untility.
   SET /P Download=Do you want to download it now? [y/N]
:: Start download if requested
IF /I "%Download%"=="Y" (
   START "DevCon" "http://support.microsoft.com/default.aspx?scid=kb;EN-US;Q311272"
   ECHO.
   ECHO Install the downloaded file and make sure DEVCON.EXE is in the PATH.
   ECHO Then try again.
:: Abort if DEVCON.EXE is not available yet
IF "%DevconAvailable%"=="No" GOTO End
:: List and remove all USB devices
>> RenewUSB.dat ECHO.%Date%, %Time%
DEVCON FindAll =USB | FIND ":" >> RenewUSB.dat
FOR /F "tokens=1 delims=:    " %%A IN ('DEVCON FindAll ^=USB ^| FIND ":"') DO DEVCON Remove "@%%A"
DEVCON FindAll USB* | FIND ":" >> RenewUSB.dat
FOR /F "tokens=1 delims=:    " %%A IN ('DEVCON FindAll USB* ^| FIND ":"') DO DEVCON Remove "@%%A"
:: Rescan for new hardware
DEVCON ReScan
:: Done
ENDLOCAL
GOTO End
:Syntax
:End
all USB enteres will be removed, and USB devices will be redetected, if mess exist will be solved.
after USB devices are recognised navigate to device manager locate your USB mouse double click on it and untick "allow the computer to turn off this device to save power" config OK.
reboot.

K8n neo Platinum and Optical Drive problem?

I need some help figuring this out. I've been searching for awhile but can't find any more information so I figured I'd ask here.
I have a Lite on LDW 411s dvd writer that is on the same ide channel as a lite on dvd player (labled as JLMS SJ-HD1665 in the device manager.
The problem is on the 411S where it will read the DVD/CD disk but when I try to use Cyberlink PowerDVD or Nero Recode to play or read the DVD it will just hang. If I don't try to play these files and just open them in explorer then I can access them.
I'm trying to see if there are some conflict issues with the nforce drivers but am still looking.
My setup is this.
AMD 64 3000+
K8n Neo Platinum nforce 3 250 Bios 1.4
Western Digital 120 gb hd
PQI 3200 1 gig memory
PNY 6800 GT
Audigy 2
Antec Trupower 420
Any help would be great as I'm totally stuck. Thanks.
Also to note I can play DVDs and use recode fine off the DVD rom drive but just not off the DVD writer (411s).

Quote
Originally posted by BluddSimple
I have a Lite on LDW 411s dvd writer that is on the same ide channel as a lite on dvd player (labled as JLMS SJ-HD1665 in the device manager.
You might have better luck making the reader the slave on the channel your HD is on. I had both a burner/writer on the same channel and while it worked, the performance was very poor.
Man, I need to get around to posting my specs someday, but I have the same MB and BIOS as you. I'm also using the nForce unified drivers including IDE.

K8n neo platinum and hard drive problem...

greetings...
well, I have K8n neo platinum mobo with SATA1 controller, and I bought WD 250 GB sata2. I did set up jumper to limit transfer to SATA1 mode on my new drive (although I tried it without jumper, it is the same). Hard disk is working but, I have varying trasfer rate when I copy files from WD250 on other drives, and when copying on that drive. Transfer is going fine, and then it goes very very slow, then again fast, then again slow...And, sometimes, when I am copying large amount of data on that drive, my computer freezes. When I test sustained speed, it is different almost every time (goes from 14 to 65)...
I searched thru internet - with no sucess. I have very good power for my PC. I changed sata cables, and power cables. I updated all drivers. I tried installing XP IDE drivers for that new SATA2 hard disk. I tried almost everything, and with no sucess. WD250 is working fine for, let's say, a couple of hours, and then it again goes slow with varying transfer rate when copying. I also have a very good cooling system, so it's not because of overheating. I contacted WD, they told me to run their diagnostic tool, and the disk was healthy. They said that drive is ok then, and that it is probably my mobo that is causing problems.
anyone have a clue what is going on?
thanx in advance

damn...
can't believe no one ever had similar problem...

Re: MSI 785GM-E51 and memory modules problems -l- Split

I am using AMD PHENOM II 1055 125w CPU on MSI 785GM-E51. Memory Corsair XMS3 DDR3-1600 x4
I can put memory in slot 1 and 3 it will boot fine.
If I install DDR3 in slot 1 and 2 the system will not boot. If I full populate all the memory slots it will not boot
In both scenario's after the system does not boot and go back to just using slots 1 and 3 the system boot with CMOS checksum error and need to go in to BIOS setup. All the changes need to be made again, saved and exit and it reboots fine.
I have already attempted to setup the memory speed to 1333 and 1066 with no luck. Any ideas?
785GM-E51/BIOS 2A0, Phenom II T1055 @ 2.8 GHz, 125W Stock AMD Heat sink&Fan
Corsair 2x2GB CMX4GX3M2A1600C9, 9,9,9,24, 1T, 1.47V, 1600 MHz --------- 2 kits
ESXi 4.1
Antec 650 Truepower
ATI x600 PCI-e
Adaptec AAR-2610A with 5 WD Caviar RE WD2500SD-01KCB0 250GB RAID-5 Configuration
NEC ND-2501A DVD-Burner

Topic split, don't hi-jack other peoples topics. >> Please read and comply with the Forum Rules <<
Provide more information on your system, read this: >> Posting Guide <<
See my signature for example of information to provide.

K8N Neo Platinum and BGF 6800GT problem

Hey
recnetly set up my board, and having some issues with freeze midgame and really poor 3d mark scores, i.e. im getting 22000 in 2001!!
How do i stop this problem, and power shoudnt be a problem given the power supply i have, so would anyone have an idea?
What should i set the bios up to look like and anything in XP i should be doing?
thanks

Not sure about the mid-game freeze, but your 3DMark01 is spot-on with that score, if not a bit high. My 3500+ gets ~22.5k at stock, but at 2.5GHz I get 24645. It's very CPU limited so your video card isn't going to make much of a difference past a certain point.
What games are you experiencing lock-ups in?
I'll try to cover all bases here, so some things might help, others not:
1: Make sure your power inputs are connected properly (I know, it seems so obvious it's insulting, sorry).
2: Disable NV/ATI speedup in the BIOS. To reveal hidden BIOS options and reach this setting hit Shift+F2 and ALT+F3 all at the same time. Someone let me know if that's the wrong combo but I think it's correct.
3: Grab the 71.20 FW drivers, they're about the best you can get right now, don't get the crap 66.93 officials, their performance doesn't compare in most situations.
4: Disable Fast Writes in the BIOS; sometimes this has helped fix stutter problems, but if you're getting FREEZES... well it might not help.
5: Drop all clocks to stock settings and see what happens. If that works, try different OC settings if you want.
6: Update your games, of course.
7: Defragment your hard drive.
I highly recommend downloading 3DMark03, 05 and AQ3 and reporting your scores there and whether or not you get freezes/stutter in those benchmarks. 3DMark03 and 05 are more video card intensive and should exploit the problem you're having. AQ3 might do it too.
Just suggestions, nothing's guaranteed to work. Post back though if you have any new information or if you get it fixed.

MSI NEO 2 and Gf 8800gt problem

Similar Messages

Maybe you are looking for