MSI NEO2 and Asus v9999GT problems

Hi,
well my problem is when the Asus v9999GT is installed i boot windows up but it just keeps restarting or blue screening(i see the desktop then it restarts*if i dont get a blue screen that is) It usely takes 4-5 restarts before windows finally starts. Ive reinstalled the comp 4 times trying to fix the problem but had no luck finally i reinstalled the comp with my 9000 Pro II and no more restarting no more blue screening windows starts normally. But thats not a fix i bought the new card and im not going to let $530 go down the drain. It seems to me its the NEO 2 that does not like the Asus, i try the asus in my old comp and everything works fine.
Is there a fix coming up, i know others who have the same problem
btw its not the ram i did a memtest and no errors
AMD 3500+
MSI Neo 2
1Gb Geil RAM CAS2.53-3-7
Asus v9999
Windows SP2

I don't think it's PSU related caused by the gfx card if
it is the asus 9999GT/TD . As this is a 6800 board with GT core clock
and 128M DDR1 memory.
And in 2D windows it should use estimatly 20W .
:Xbitlabs
The NVIDIA GeForce 6800 eats less energy than the GeForce GT as it has lower frequencies and the GPU voltage . As a result, without overclocking, the card consumes 16.96W(10w on +12v) in the Idle mode(2D) and 38.88W in the Burn mode(3D).
Real GT:
23w in idle mode and 53w in burn mode(3D) .
So it consumes something between those two i guess.
If you suffer from restarts in only in windows (2D) your gfx card don't use
any more power than your R9000 in 3D does (which worked running games i guess).
But if you didn't run/test the 9000 in any burn mode or 3dmark , it might
be PSU tipping over afterall.
Could be some drivers/sw causing it.
Try to edit your boot.ini file and turn off DEP
Edit noexecute switch it to be like this:
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /noexecute=alwaysoff /fastdetect

Similar Messages

  • Msi neo2 k8n 54g platium problem?

    After i got my Gecube x800xt pe and installed it, when catalsyt 5.1 was out, i got these irretating problem's, When i set my memory to eggressive timing's and 1T  C L=2.0  Trcd=4  tras=8 Trp= 4 my pc freezes, it's all under the cell menu,i do ofcourse turn off dynamic overclocking, still i get the freezes,and the message after reboot, vpu recovery, anyone know what the problem could be?
    Seasonic super silent 460W
    Amd 64Bit 3500+ 0.9 [idle38--Load 42]
    Msi Neo2 54G K8N platium [Bios 1.5]
    Gecube x800xt pe
    Geill pc 4400 ultra dual
    Sb Audigy 2 Zs
    Asus Tv tuner
    2*120Gb
    2*160Gb
    1*250Gb
    1*300Gb
    I tried to take everything out of the pc, so it just has what it takes to start op, i even tried Catalyst 4.10/4.11/5.1/5.2/5.3, and also other older motherboard driver's and newer beta's, i tried the pc in other pc's and it didnt do it there, then again hey were cheap motherboard's and didnt have all those memory feats as this motherboard. plz help me

    bejon2000,
    Good point bejon,
    I re-read the article and this what it says: " ....If you remember, older Athlon 64 processors based on 130nm cores didn’t support 4 double-sided DDR400 SDRAM modules working at 400MHz frequency at all and reduced their frequency to 333MHz automatically. The today’s processors based on 90nm cores offer us a few better solutions. The D core revision also known as Winchester allows using four double-sided DDR400 memory DIMMs if the Command Rate timing is set to 2T."
    From what you posted the Winnie D core CPU may need a little TLC and voltage boost. but it should run 4 X double sided 512 sticks at DDR 400 and 2T. Venice or later core may not need such TLC or voltage boost but still need manual  selections in BIOS Cell menu.
    Thanks for pointing this out,

  • MSI NEO2 FISRH 865 BIG PROBLEMS

    I have the following problem.  My computer gets jammed after a time (arbitrary moment).  With get jammed  I mean that the screen  freezes and you can nothing more than a reset.  Mostly it happens in Internet Explore.
    My computer:
    Pentium 4 2.6 GHz 800 FSB
    2 x 512 MB DDR400 Ram Twinmos CL3,3,3 in dual
    MB : MSI NEO2-LS FISR2H ( chipset 865 PE) BIOS versie 1.1
    grafic: Aopen geforce 4 MX 440-se
    HD: IBM 80 GB
    wireless mouse and keyboard logitech
    Software
    Windows XP pro service pack 1 (all update's)
    Drivers van Nvidia installed  
    Virusscanner Norton Antivirus ( up to date)
    DirectX 9
    I have tried.  
    * turning off Hyper threating
    *More fans : 3*80 mm fans and 2 x 120 mm fans (placed according to rules
    intake/outtake)
    *replacing RAM and tested with MEMtest86 (no error's)
    *replacing keyboard and mouse with wired keyboard and mouse
    *replacing graficcard with a other brand (same model) and a other brand (differend model)
    *changing hard disk
    *reinstalling windows
    *replacing IDE wires
    *keeping a eye on the temperature (is normal )
    *keeping a eye on the voltage ( normal)
    *replacing power supple with a heavere one
    But nothing helps.  Does some one knows what the problem can be or do i send it back and ask for a RMA.  And buy a motherboard that does work.. : ?(   :O

    foxie,
    My first 865PE Neo2 FIS2r board had BIG problems with on-board LAN, didnt work at all most of the time. No systemcrashes but you could not connect to Internet or LAN.
    But since a PCI networkcard work OK, it wasn´t difficult to RMA it to my lockal computershop. They got the same result. I got a new board that work perfect.

  • MSI KT3 and G4TI 4200 problems

    Hello,
    I'm having some problems with new MSI hardware and hoping to could get some advice. I've read though the forums but I'm left more lost and confused than enlightend  ?(
    Problems..
    1. Cannot get MSI G4 4200 to run in AGP 4x. Once enabled in bios 3D Mark 2001 and all games crash in 4x mode. Ok in 2x.
    2. Cannot get Live update to work with any Nividia drivers. (Need MSI Video card) It says..
    3. Cannot get 3D! Turbo Experience to run. Get an MSIVGA.ocx ininalization error. Then get a popup box saying..
    ***MSI VGA Monitor Warning Message***
     Memory I/O voltage is unusual
     Now memory I/O voltage is : 2.69 Volt
     Memory voltage is unusual
     Now memory voltage is : 3.26 Volt
    What?
    Though PC Alert nor SiSoft Sandra reports any errors.
    Motherboard: KT3 Ultra with latest bios installed
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=11&MODEL=MS-6380E
    Video Card: G4Ti4200-VTP MS-8886
    http://www.msi.com.tw/program/products/vga/vga/pro_vga_detail.php?UID=350&MODEL=MS-8886
    Power supply Unit:  350W Enermax • EG365P-VE FC
    http://www.enermax.com.tw/product.htm
    WindowsXP Pro SP1
    Nvidia beta drivers 4072
    AthlonXP 1700+
    512 Megs PC 2700 Samsung DDR Ram
    Creative Soundblaster Live Platinum 5.1
    Seagate 60 Gig ATA 133 Drive
    Thanks

    You could install MSI's PC Alert 4 and monitor the voltages and temp.
    http://download.msi.com.tw/support/swr_exe/pcalert4.0.0.2.exe

  • MSI g4mx460 and asus cuv4x-e(via apollo133a) problem

      I have a Asus Cuv4x-e motherboard (via apollo133a chipset 694x) and recently i bought a MSI Geforce4 mx460 with video-in and tv-out. I got the registry fix to use agp4x, but the system hangs in games and capture feature and tv-out doesnt work.
     I've heard a issue about geforce chipsets not working with via apollo133a.
    Can anybody help me? i tryed a lot of things. If anyone knows how to solve this or is having the same problem please contact me: [email protected] or post a message here.
    Thanks for any help,
    TNGA

    Quote
    Originally posted by TNGA
      I have a Asus Cuv4x-e motherboard (via apollo133a chipset 694x) and recently i bought a MSI Geforce4 mx460 with video-in and tv-out. I got the registry fix to use agp4x, but the system hangs in games and capture feature and tv-out doesnt work.
     I've heard a issue about geforce chipsets not working with via apollo133a.
    Can anybody help me? i tryed a lot of things. If anyone knows how to solve this or is having the same problem please contact me: [email protected] or post a message here.
    Thanks for any help,
    TNGA
    Hi. I don't have the solution that you need. But I'd like to receive the registry fix that you wrote, if you alredy have that. I having problems with my mx460-vtp because it don't works in AGP 4x mode (actually in 2x mode). Thanks.

  • Msi K8N and possible directx problem

    Hi guys,
    System
    MSI K8N Neo Platinum
    AMD 64 3200
    Enermax 600w (2*12V rails, one at 18, the other at 17)
    WinXP, Dx9c
    Other system components 1xSeagate 80gb SATA, 1xLiteon dvd/cd-r
    512Mb Kingston Ram (1 stick)
    Used MSI Live to update board bios to latest as well as nVidia chipset drivers.
    Asus Geforce4 Ti4200 128mb
    Doom3 runs without a hitch,
    UT2004, Everquest both are displaying serious graphical problems including missing textures, shearing, alot of  flickering
    Dxdiag performs all tests without any errors, have yet to try 3dmark.
    Tried changing AGP to 4x and disabling fast write, together and seperatly, graphical concerns only seemed to worsen.
    I have already upgraded to the PSU mentioned above as the Antec that i was using wasnt up to the task, this allowed the 3d games to actually run.
    So, any ideas on what I should be trying next? It seems that Open GL games are performing normally, whereas directX games are causing trouble.
    Josh.

    Thanks vlovich,
    I have tried the nvidia drivers v61.76  and 61.77 and also tried the beta v62.11 and v62.20.
    I have not oc'ed the video card at all, tho winXP is reporting it as running at 8xagp in the device manager applet. When i modified the agp speed in the bios to 4x the problems "seemed" to get worse so I put the setting back to auto.
    I haven't attempted the asus drivers, so I will give those a go.
    Josh.

  • MSI 8500GT and Viewsonic 24" Problems

    I have a MSI NX8500GT-TD256EH (GeForce 8500GT) connected to a ViewSonic VX2435WM. The monitor has a HDMI input and I am using the included DVI to HDMI cable. The native resolution is 1920x1200. I'm running Vista 32-bit with 163.69.
    Before I load the Nvidia drivers, the picture looks normal. However, once I load the drivers, the picture becomes distorted (blurry text, messed up colors, etc). When I look at the resolution notice on the monitor's OSD, it says it is running at 1200p. Before the Nvidia drivers are installed, it says it is running at 1920x1200.
    I've looked all over the Nvidia control panel and I believe the software thinks the video card is connected to a HDTV, rather than a monitor. It shows that it is being connected via HDMI, even though the output on the video card is DVI.
    I have connected the monitor to some other other computers and it works fine on both a Radeon 9600 and a MSI 8600GT. They are all connected the same way: DVI output from video card into HDMI input on monitor. When it is connected to these computers, the monitor's OSD correctly recognizes 1920x1200 and the Nvidia control panel shows it is connected via DVI.
    I have tried a few different versions of the latest ForceWare drivers and also tried BETA drivers. Right now I am running 163.69.
    Any suggestions on what I can do to get a clear image? Right now the only thing that works is uninstalling the Nvidia drivers and using the standard VGA drivers from Microsoft, which obviously isn't an option.

    There's a slight chance that the nVidia driver can't read what modes the screen can display - although it seems unlikely.
    I had problems with an NEC HDTV (1366 x 768 native resolution), which would work perfectly with a 1360 x 768 analogue VGA input, but if I tried the DVI-D input, the card (7300GS) sent out 1280 x 768, and the picture panned when the cursor went off screen. This was nVidia's response...
    Thank you for contacting NVIDIA Customer Care. NVIDIA GPUs allow resolutions depending on a monitor EDID. An EDID is an electrical signal sent by a monitor/tv which tells it which modes it supports. While set top players designed specifically for HD modes may not need this, PC's do since they support many more types of video display modes and to prevent damage to a display, will only send out a signal that a monitor tells the graphics card it supports. An HDTV generally only accepts HD signals through the DVI or HDMI input and therefore it's EDID through this input only accepts HD resolutions such as 720p (1280x720). However through your VGA input, it will allow different resolutions and therefore the EDID that the HDTV sends to the graphics card through the VGA input is different from that of the HDMI/DVI output. This is why the graphics card gives you different options depending on which input you have it hooked up to. If you wish to use your HDTV for only movies, we recommend using the DVI input however if you will be using it as a PC monitor where you may need to read text or view small objects, then it is recommended that you use the VGA input which will allow you to run without any scaling. Unfortunately, there is no workaround for this situation as everything is working as designed.
    Sometimes the technology is too clever by half!
    However, this doesn't explain your problem if you can get it to work with a different card, but the same driver.
    The only other thing I can think of is that the monitor isn't mapping the incoming pixels to the display pixels properly, although that should only apply to analogue inputs, since with DVI/HDMI, each pixel value is sent as a binary number, and it's position is inherently defined. With analogue signals, there's no separate clock signal to tell the monitor exactly when to sample each pixel, hence the Clock and Phase adjustments.
    Maybe it is the HDCP nobbling the resolution - if the monitor doesn't tell the 8500GT that it supports HDCP, the 8500GT might decide to throttle back the resolution. Grrr!
    Probably not much help I'm afraid, maybe someone else has some ideas.
    Cheers

  • MSI K8T and 3400+ HUGE problem

        I'm in computers since 1993 and I've never had a single problem I was unable to deal with. But my last 4 days have become a nightmare  . I guess it's finaly time to ask someone for help.
    So I descided to make an upgrade and got myself a MSI K8T Neo-FIS2R motherboard and a AMD 64 3400+ Clawhammer CPU. The expected from me 10-minute long upgrade operation became as I already said 4-day long and I still don't see light in the tunnel.
    So what the problem is - I put together the hardware but when I pressed the power up button I got "Bios not installed" message at start up along with "CMOS settings wrong" and "If you have built SATA Raid array prevoiusly go to p20378 SATA controller set as raid".
    Press F1 to enter setup
    Press F2 to load defualt values and continue
    If I go into bios and set the time etc. and reboot the system it hangs. The PC seems to reset but the monitor shuts down so I don't know if the PC is hanging or I'm losing the signal to my monitor?
    If I press F2 Windows XP loads up fine but I can not change my agp setting etc. as the system fails to boot after saving bios config and I have to clear the CMOS using the jumper in order for me to restart the machine. When I shut down the machine in XP I still have to clear the Cmos in order to boot.
    Even if I'm willing to clear the CMOS every time I want to turn my PC on there's still another problem. After eventualy Windows XP loads the CPU is running on rediculous 800 MHz instead of 2200 MHz. The problem is the multiplier which is set on x4 and won't move from this possition. The problem is not Cool'n'Quite because I don't have the software for it installed under Windows XP. And using the BIOS default settings by pressing the F2 button in the begining I guess is turning the Cool'n'Quite off in the BIOS.
    I updated the BIOS and all the drivers to the last from the MSI webite using the last version of Liveupdate 3.
    I even tried changing the Cmos battery even though the MoBo is brand new. Still same thing.
    Pleaseeeee give me some ideas of how to sort the problems out. I'm really geting MENTALY unstable    

    Hello again and thank you for the quick respond. I'll start with the system specs first:
    MB   MSI K8T Neo-FIS2R(601-6702-010)
    CPU AMD Athlon 64 3400+ Code name Clawhammer Brand ID 4 (Core Speed 801.8MHz, Multiplier x 4.0 HTT 200.4) - CPZ v 1.31 results
    CPU Cooler Gigabyte 3D Rocket PCU22-se
    GC   nVidia 6800 GT 256 MB (Leadtek)
    RAM 1x 512 MB Corsair Value PC 3200 / 1x 512 MB MTec PC2700
    HDD 30 GB 2 MB Cache 7200 rpm Maxtor DiamondMax Plus 8 ATA/133 on IDE 1 with jumper set as Master
    HDD 160 GB 8 MB Cache 7200 rpm Seagate Barracuda  Ultra ATA on the same cable attached to IDE 1 but with jumper set on Slave
    CD-RW Drive LG 52x24x52 GCE-8520B
    DVD Drive LG GDR8162B
    PSU Jeantech 450 W http://www.jeantech.com/450.htm
    ... and a floppy
    Now to answer on your questions 1 by 1.
    First of all the fisrt thing to do after the software war was to change the Cmos battery with a new one and try - no good - still the same problem.
    Second - The PSU I belive is sufficient. And Yes I have the 4 pin/12 V power connector for the CPU power connected.
    The D-Bracket - after I start the computer it gets to the screen with the F1 setup or F2 load default and continue. As I said before if I press F1 and make all the BIOS settings as time, date,  sequence etc. and press Save changes to BIOS and Exit the PC seems to reset but the monitor shuts down. At this time D-Bracket indicates "Early Chipset Initialization" (Upper left light in green and the rest in red) and stays like this forever. After I clear the Cmos it starts again and it gets to the same screen with the message "CMOS settings wrong" and the 2 choices F1 setup or F2 load default and continue.
    Fourth -  I don't have any SATA drives at all.
    About memtest - I got the banks of RAM from my WORKING PC and just installed them the new MoBo. And because one of them is 333 DDR I descided to remove it and try with only the Corsair one which is 400 DDR. I tried and vice versa too - still the same problem.
    As I said before if I choose F2 and load the default BIOS settings Windows XP loads and the PC is stable - no random resets or any unstability problems whatsoever. Problem is the CPU is working on only 800 MHz - because of the x4.0 multiplier.
    That's all I can say. Please give me some advise - I haven't had normal sleep for 5 days already - I just can't accept the fact that I can't manage to sort out my problem. Thanks again!

  • Msi Diamond and four memorycomps - problems?

    I have installed four 512Mb ddr566@500 comp's and now when I have used the machine a while, winxp will pop up a blue screen. The machine will restart then (so quickly, that I can't read the errormessage).
    Before I had two 512Mb ddr566@500 comp's, without problems.
    Is this board unable to handle four memorycomps, or what might be the problem? I have already ran memorytest succesful. In the manual reads, that when using four comp's, the maxium speed is ddr333? The cpu is Opteron148, with venus core.
    Edit. BTW can someone say, is my PSU strong enough to run whole machine. It is Tagan 2force 480W and machine: Msi diamond, 148Op, 2Gb ram, 2x 6800 ultra, 2x hdd, audigy4 pro, 3x 120mm casefan. When I plug two more hdd's, nvidia system will show error, that power is not enough to graphic cards. The manual says, that the mainboard want 450W or more psu.

    MSI always have the color code for vdimm.
    It's what the vendor of the modules state for nominal voltage that counts .
    If they say 2.8 i would run 2.8 or higher (not below) . 0.05 higher to compensate for voltage drops during load.
    Double 6800 Ultras (stock clocked) pci-e draws something around 70w from the +12v line each in full 3D mode/load. (in idle 2D mode about 30w each)
    Thats almost 6A per card , times two it's 12A just for your graphics in the highest load situation .
    I'm not sure though if SLI balances toe load exactly equal , but lets assume so to be sure .
    Then atleast 8-10A from +12 goes to your cpu depending on model and if overvolted/overclocked .
    And consider apx. 1A +12v usage for each HDD and optical (although the use a bit more at spinup , but then the gfx's are in 2D mode) .
    1A +12v for mobo .
    Fans run off +12v .
    Memory runs off +3.3v or +5.0v depending on motherboard design .
    Add things up and have a rule of using a load target for the PSU @ 80% (fully loaded PSU's loose efficiancy and stability .
    There is some guideline of SLI building and dimensioning of PSU you might wanna check out over at nvidia .
    http://www.nvidia.com/object/slizone_howtobuild_2.html

  • Msi neo2 and crucial ballistix

    I found out that my 2x512 ddr400 crucial ballistix is bad. So i tested 1 of the sticks in dimm1 with memtest.  It did 5 passes then i quit so i think one stick is fine.  Either the other stick is bad or dimm2 is bad.  How do i figure out if dimm2 is bad?  I know that you can only have module in dimm1 or 3 if its single channel. 
    The settings on the ram was 2 2 2 6 1T 2.8v.  Both were in dimm 1 and 2.

    Hello,
    What neo2 board do you have?
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=607
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=649
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=650
    No you dont have to untick anything.
    The nvidia Audio drivers should work with the realtek codec.
    Or you can use the realtek audio drivers.
    I prefer the nvidia audio drivers.

  • MSI-5169 and 40gb HD Problem

    Hi
    We have a computer running on a msi-5169 motherboard v2.9.  We bought a Western Digital 40gb hard drive for it but it will not recognise the drive.  The bios was sitting on version 2.5 so we upgraded the bios to version 3.6 hoping this would sort out the problem.  But it still does not work.
    Is this motherboard not compatible with drives this big?  Is there anything we can do?
    Thanks
    Haggis

    limit it to 32gb with another jumper
    http://www.msi.com.tw/program/service/forum/index.php?threadid=1438&boardid=16&styleid=1
    note also stand alone jumperless master setting

  • Vga silencer (ati) fit on msi neo2 939

    I am concerned about the clearance between the northbridge fan and my vga silencer (ati ver.1)  used currently on my ati 9800pro.  I have ordered the msi neo2 and think that it will barely fit but wondered if anyone else have noticed this.
    Thank you
    Kim

    I had a little problem installing mine. It took me a couple of minutes to figure out what was going on. The H/L switch on the VGA Silenser was hitting one of the capasitors on the mobo and I couldn't push the card all the way in. I had to unbolt and reposition the switch. And like the others said there's not much room between the NB fan and the card, but it does fit. I think it would be chalanging trying to get to the AGP slot clip with that tight fit. Good luck!

  • OEM Visiontek AGP GeForce2 GTS, 32MB DDR on MSI Neo2 Platinum as temp fix?

    I'm taking my ATI 9700 Pro to ATI to have it RMA'd for some rolling interference lines. I've done troubleshooting and its the card.
    Will I have any problems using this Geforce2 GTS AGP card as a temporary replacement while I wait for the ATI card to be fixed? I'm swapping it and I get $5 for my Matrox G400 max AGP card. For obvious reasons, I'm not keeping and using the G series Matrox G400 since it won't work in my PC with the MSI Neo2 and BIOS 1.4 etc etc
    So any problems using this as a temporary replacement?
    OEM Visiontek AGP GeForce2 GTS, 32MB DDR
    thanx for any feedback,

    Forgot to do that! Its working fine though. I'll try to clean out the old ATI drivers. This is only temporary and I'll be wiping this system clean and starting over anyways.
    So far its ok. Another troubleshooting verification that the 9700 Pro I had was faulty. With this gforce2 gts the rolling horizontal lines are absent.

  • MSI 870a-G54 Hard drive problem.

    About a week ago i reinstalled Windows because it started to slow down (virusses and what not) And as soon as i reinstalled everything (programs games etc etc) One of my harddrives used for games did not show up at the bios and at My computer.
    So this entire week i've been trying to get it to work again and i've narrowed down the problem today to the BIOS and/or motherboard not giving the power to the HDD in order for it to start and be recognized in BIOS and Windows.
    What ive done to come to this conclusion:
    - Reinstalled Windows twice,
    - Replaced CMOS Battery,
    - Flashed the BIOS to every BIOS setting the MSI website had to offer. None worked for the HDD to get powered up again.
    - Moved CMOS jumper,
    - Changed SATA and powercables on harddrive,
    - Tried the HDD on another test PC i had and reformatted it there as well,
    - Only hooked up the not working HDD to the PC, (HDD did not spin up, and came to the conclusion at this point that motherboard or BIOS is the culprit)
    - Unplugged the powercable to the not working HDD and plugged it back in when the PC was running and i could feel it spinning up, after this i restarted the PC so that the HDD would still get power and it was recognized by the BIOS and Windows and i could use it. As soon as i shut down the PC entirely and restarted it the HDD would not spin up. And i had to unplug power to the HDD and plug it in again and restart PC for it to work properly.
    - Checked for bad sectors nothing found,
    Everything else is working perfectly. Except that one HDD not getting the power when booting up the PC.
    The HDD in question is the "Samsung HD502HJ 500gig" used for Steam games.
    PC Specs:
    CPU: AMD Phenom II x4 955 Black edition. Put on a new CPU cooler last summer (Cooler master Hyper 212 Plus)
    Mobo: MSI 870a-G54
    PSU: Antec EarthWatts EA650 (650 Watts)
    Graphics card: Powercolor PCS+ HD5870 Put on a custom cooler last summer (Arctic Cooling Accelero Xtreme 5870)
    RAM: Kingston ValueRam 1333Mhz DDR3 (8gigs 4x 2gig) Bought 4 gigs extra last summer
    HDD1: Seagate ST3160812 AS 160gig used for Windows 7 Ultimate 64 bit (Works perfectly)
    HDD2: Samsung HD204UI 2TB used for Storage / Other games than i have on Steam. (works perfectly) Bought last summer with the cooling/system upgrade
    HDD3: Samsung HD502HJ 500gig used for Steam games. (Does not work anymore after reinstal) Bought 2 years ago along with the rest of the PC
    I am completely at a loss here as to what the problem is. I do not have the funds to buy a new piece of hardware at this time (i think the entire week of struggle would back that up for me lol...). And ive basically tried everything what i know and what i've found through Google and friends. Might have been better going straight to MSI forum and post my problem here but narrowing it down to this not only helps me but the person that is going to post below in this thread as well lol.
    Thanks in advance and i hope to hear from anyone soon.

    Quote from: Bas on 09-March-12, 19:16:21
    Try drive in different PC, as it looks like it died.
    HDD's always spinup as soon as power is applied, ergo I think the drive died.
    Ive tried it already in 2 different PC's and i have to apologize here for not mentioning that earlier in the topic.
    The drive spins up perfectly in both of those PC's and ive checked for bad sectors on both of those PC's as well and it showed that the drive was 100% healthy on both PC's
    The drive was working perfectly fine before the reinstallation of windows. Thats why i dont think the drive has died. Because it would be weird that the drive just suddenly gave up right when im reinstalling windows..
    It also doesnt add up when i plug the powercable back into the drive while the PC is running and it spins up then and works perfectly until PC is shut down. Thats why i had it narrowed down to the BIOS and/or Motherboard being the culprit.
    My best guess is that its software related because the PC does boot up so its not a hardware problem.
    P.S.
    A friend of mine said that it could be a powersaving issue. But ive looked into the BIOS and i could not find anything about it.

  • MSI ex600 sound headphones&speakers problem

    Hello all I have MSI ex600 and i have problem with my sound
    When speakers playing some music and i want hear it in my headphones its problem because speakers playing away
    So i hear music on headphones and speakes too
    I try find some solution (and its many problems with this stuff) but for me didnt work
    Some information of me Sound card :
    Sound(a)   : 82801H ICH8 Family HD Audio Controller module: snd-hda-intel
    [root@SilentHill ~]# lsmod | grep snd
    snd_seq_oss            33408  0
    snd_seq_midi_event      7936  1 snd_seq_oss
    snd_seq                55936  4 snd_seq_oss,snd_seq_midi_event
    snd_seq_device          7956  2 snd_seq_oss,snd_seq
    snd_pcm_oss            42400  0
    snd_mixer_oss          17024  1 snd_pcm_oss
    snd_hda_intel         374568  3
    snd_pcm                82312  2 snd_pcm_oss,snd_hda_intel
    snd_timer              22536  2 snd_seq,snd_pcm
    snd_page_alloc          9232  2 snd_hda_intel,snd_pcm
    snd_hwdep               9096  1 snd_hda_intel
    snd                    57320  15 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_hda_intel,snd_pcm,snd_timer,snd_hwdep
    soundcore               8096  1 snd
    [root@SilentHill ~]# cat /etc/modprobe.conf
    # /etc/modprobe.conf (for v2.6 kernels)
    # alias wlan0 ndiswrapper
    # --- BEGIN: Generated by ALSACONF, do not edit. ---
    # --- ALSACONF version 1.0.15 ---
    alias snd-card-0 snd-hda-intel
    options snd-hda-intel index=0 model=5stack
    alias sound-slot-0 snd-hda-intel
    # --- END: Generated by ALSACONF, do not edit. ---
    That was my last stuff what i tried (options snd-... in modprobe.conf)
    Thanks and sorry for my bad english

    Add this to your modprobe.conf :
    options snd-hda-intel model=3stack-6ch
    It will add a headphones switch to your alsa control which if you disable will mute the onboard speakers.
    Works on my MSI vr600

Maybe you are looking for