Msi neo2 k8n 54g platium and 4 memory sticks problem

Hello i used to be running with 2x 512 geil ddr 550mhz ultra ddr ram, and got a deal at my friends pc store, about 2x 512 geil ddr 500 ultra set ddr ram, but when ever i put the 2 new stics in my pc it dossent even give me a screen, i just powers op no screen and my monitor just blinks in the power led, then i take them out,and runs again, i tried a newer amd 3500 with a newer memory controller, but no luck, i even tried setting the memory setting all to auto or as high they can get in cas latency, still no luck, and the two sticks i had in was dual, and so are the new ones , hope you guy's can help
My Pc Spec's
Amd 3500+
Msi k8n ne2 54g platium [bios 1.B Newest 1]
2x512 geil Ddr 550Mhz Pc 4400 [the ones i want to add are 2x512 geil 500Mhz pc 4000]
Gecube Ati x800xt pe
Sb audigy 2 zs
Asus TV card
2xSeagate 120Gb Ata 100 i think
2xSeagate 160Gb Sata [Raid]
1xWestern digital 250Gb Sata
1xSeagate 300Gb Sata
Sony Dvd burner
Cdrom 52x
hope this helps too

bejon2000,
Good point bejon,
I re-read the article and this what it says: " ....If you remember, older Athlon 64 processors based on 130nm cores didn’t support 4 double-sided DDR400 SDRAM modules working at 400MHz frequency at all and reduced their frequency to 333MHz automatically. The today’s processors based on 90nm cores offer us a few better solutions. The D core revision also known as Winchester allows using four double-sided DDR400 memory DIMMs if the Command Rate timing is set to 2T."
From what you posted the Winnie D core CPU may need a little TLC and voltage boost. but it should run 4 X double sided 512 sticks at DDR 400 and 2T. Venice or later core may not need such TLC or voltage boost but still need manual selections in BIOS Cell menu.
Thanks for pointing this out,

Similar Messages

Msi neo2 k8n 54g platium problem?

After i got my Gecube x800xt pe and installed it, when catalsyt 5.1 was out, i got these irretating problem's, When i set my memory to eggressive timing's and 1T C L=2.0 Trcd=4 tras=8 Trp= 4 my pc freezes, it's all under the cell menu,i do ofcourse turn off dynamic overclocking, still i get the freezes,and the message after reboot, vpu recovery, anyone know what the problem could be?
Seasonic super silent 460W
Amd 64Bit 3500+ 0.9 [idle38--Load 42]
Msi Neo2 54G K8N platium [Bios 1.5]
Gecube x800xt pe
Geill pc 4400 ultra dual
Sb Audigy 2 Zs
Asus Tv tuner
2*120Gb
2*160Gb
1*250Gb
1*300Gb
I tried to take everything out of the pc, so it just has what it takes to start op, i even tried Catalyst 4.10/4.11/5.1/5.2/5.3, and also other older motherboard driver's and newer beta's, i tried the pc in other pc's and it didnt do it there, then again hey were cheap motherboard's and didnt have all those memory feats as this motherboard. plz help me

bejon2000,
Good point bejon,
I re-read the article and this what it says: " ....If you remember, older Athlon 64 processors based on 130nm cores didn’t support 4 double-sided DDR400 SDRAM modules working at 400MHz frequency at all and reduced their frequency to 333MHz automatically. The today’s processors based on 90nm cores offer us a few better solutions. The D core revision also known as Winchester allows using four double-sided DDR400 memory DIMMs if the Command Rate timing is set to 2T."
From what you posted the Winnie D core CPU may need a little TLC and voltage boost. but it should run 4 X double sided 512 sticks at DDR 400 and 2T. Venice or later core may not need such TLC or voltage boost but still need manual selections in BIOS Cell menu.
Thanks for pointing this out,

MSI Neo2 K8N Platinum - Freezing Issue during games

First off greetings to everyone on these forums...
I purchased the MSI Neo2 K8N Platinum motherboard from NewEgg back at the end of March to compliment the AMD 64 "Winchester" processor that I also purchased at that time to replace a slightly older AMD XP "Barton" system that was using the Abit NF7-S motherboard. For the past month I have been fighting an unusual and highly irritating issue that I have noticed during game play and have tried everything that I know of and more in an attempt to remedy this issue, but to no avail. This is the general background of the situation and now I will descibe in greater detail as to what this issue I am referring to is and the symptoms of this issue and some of the various methods used to remedy this issue.
The issue is that while play a game the system experiences a short 5-10 second freeze during the game randomly, but usually several times an hour. During this freezing the sound would loop and as suddenly as the freeze occurs it would cease and the game would continue on as if nothing happened. However, sometimes this would result in the system freezing outright after this short 5-10 second freeze... but it does not feel like a total system freeze, but rather a video freeze as the sound continues and I still have keyboard control... but this does require me to force a manual reboot of the machine itself. I have scowered the internet and various forums in an attempt to find what the issue was and use various methods to remedy this issue, but so far nothing has worked in my favor... but it does seem like this issue has been plaguing other users with the MSI Neo2 Platinum motherboard. Below are some of the methods that I have used in an attempt to solve this issue:
*Default Clock for CPU/Memory/GPU; Over/Under Clock for CPU/Memory/GPU
*Increased voltages to CPU VID, AGP, and Memory
*Disabled/Enabled AGP Fast Writes
*Increased AGP Aperture from 64MB to 512MB
*Enabled/Disabled ATI/nVidia Speedup option in BIOS
*Forced AGP clock lock to 66-67mhz
*Relaxed/Aggressive memory timings
*APIC enabled/disabled
*Gate A20 turbo/normal
*Disabled all unneeded onboard components (Realtek NIC, Sound, SATA)
*Disabled nVidia MAC and attempted to use 3Com Gigabit PCI card instead
*Swapped HDD Cables
*Tried PCI Sound Card (SB Audigy2 ZS Gamer) in PCI Slots 3/4
*Tried video drivers from 71.89 Official to 76.45 beta modified drivers
*Tried 5.10 official nForce drivers to remixed 7.02 nForce drivers (5.10 drivers uses 4.36 GART, higher drivers uses the 4.40 GART)
*Applied all the latest updates from Windows Update Website
*Reinstalled Operating System (Windows XP SP2) 5 different times clean with various settings (APIC on/off, etc...) and different drivers.
*Installed Audio Card (SB Audigy2 ZS Gamer) with older and the latest drivers available from Creative's website
*Replaced PSU (Previously was a Thermaltake 420watt PSU, 18A +12v) with a OCZ Modstream 520watt PSU (28A +12v)
*Video card is KNOWN working from previous build (AMD XP 3000, Abit NF7-S)
*Hard Drive is KNOWN working from previous build
*CD/DVD-ROM drive is kNOWN working from previous build
*Heat is not an issue... all components temperature is well below rated level, the only unknown is the chipset temperature (it has a active heatsink and seems to not be hot to the touch, applied AS5 to it anyway)
*Used latency tweak to the video card
*Used Rivatuner to force constant performance level
*Tweaked BIOS to force even clock rates and forced 1.4v to the GPU Core
*Used original GPU BIOS
*Used MSI Neo2 K8N Bios 1.4 - 1.8 and modified BIOS 1.8
*No background applications are running (not even antivirus)
*Used application to force maximum refresh rates for my monitor
*Memory passed MemTest86+ for over 24 hours
*System passed Prime95 and SuperPi for over 24 hours
*System seems stable in all non gaming related applications
*Checked through various troubleshooting procedures
*Disabled SBDRVDET.EXE using MSCONFIG
*There are no IRQ conflicts outside of PCI system management sharing IRQ11 with the NIC and USB... in APIC there are no IRQ conflicts what so ever. Regardless neither method worked
*Installed AMD 64 drivers from AMD
*Disabled DEP in boot.ini
*...and many other various tweaks and modifications.
System Specifications
CPU - AMD 64 3200+ "Winchester", using Thermaltake Silentboost K8 and AS5
Motherboard - MSI Neo2 K8N Platinum (nForce3 250GB Ultra) - Using Bios version 1.8
Memory - 2X 512MB Corsair XMS TwinX1024-3200C2PT (2 Modules, Memory Slots 1 and 2 used)
Audio - Sound Blaster Audigy2 ZS (PCI Slot 3 used)
NIC - Onboard nVidia MAC, Disabled Realtek NIC
Video - XFX Geforce 6800NU 128MB AGP (BIOS Rev 1) - NV Silencer 5 and AS5
Case - Thermaltake Damier Series 5000
PSU - OCZ Modstream 520watt (28A +12v rail)
HDD - Western Digital 1200JB 7200rpm IDE
DVD-ROM - Lite-On 16X DVD-ROM
Floppy - Mitsumi 1.44MB 3.25"
OS - Windows XP SP2/DirectX 9c
I have been fighting this issue for well over a month now and I am frankly nearly out of ideas, this does not necessarly prevent me from playing games, but this does interfere with the games I do play (especially online games). I do demand absolute stability from the games that I play and this issue only began AFTER I upgraded to the new motherboard, processor, and memory. The only thing I have not tried is something that I do not have access in attempting on this motherboard, and that is increasing the voltage to the chipset.
Here is my theory on what is going on is that I believe is there is a fault with the chipset on this motherboard and this is manifesting itself while I am playing various games on this system. Of course I would like to try increasing the voltage to the chipset as that would increase stability, but there is no option in BIOS to increase the chipset voltage like the previous motherboard I had (Abit NF7-S). It is possible that either a) the chipset is at fault and is causing me this issue or b) the chipset is not recieving enough voltage.
My question to the rest of you is this, what do you think the problem is and what ideas do you have that I may try that I have not tried yet. Additionally if there is nothing else that I may try should I attempt to RMA this motherboard and will that help, and is there any other versions of this motherboard that I should be aware of. I would appreciate any response from a MSI representative and any comments from those that may have positive suggestions for my issue. Thank you in advance for your time and any help that you may be able to render.
The GameMaster...
*EDIT* Added additional methods attempted... (there was a lot... so I did not remember everything that I have tried)

Quote from: dacull on 25-May-05, 16:06:33
Does it only happen in online games, or can it happen in all games? One thing to make sure of is to turn off CRC checksum offload in your NVidia MAC properties (everyone do this, it is incorrectly calculating checksums which leads to servers ignoring your packets). However as you have tried a different network card you can discount this theory.
For me it looks like the biggest culrpit is your 6800NU, i have read alot of bad things about the NU and you have a low bios revision there, just because it worked well against your old chipset doesnt mean it will work well against your current chipset. Sounds like a BIOS fix is needed as some timing is out somewhere.
Ensure Spread Spectrum is off (and as you have already pointed out Fast writes, ATI NV Speedup) and your card is running at default clock.
As a test beg/borrow/steal another graphics card (preferably nvidia) and see how it goes so you can narrow in on your video card.
It is not just one game, but it is more prodominate in certain games than others... the game in question here is Planetside... though I stuck a demo of Unreal Tournament 2004 on a loop bot match and it seemed to have locked up after 4 hours (not sure how many times it experienced that 5-10 freeze as I went to bed). As for the video card it was KNOWN working from a previous build in those same games (Previous build was a AMDXP3000 and a Abit NF7-S nForce2 motherboard). The only components different in this build is the AMD64, the MSI Neo2 K8N, 2 new sticks of Corsair XMS to replace the Corsair ValueSelects, and the SB Audigy2 as I would never use a software codec audio solution. Spread Spectrum is LOCKED in BIOS and disabled... ATI/nVidia speed up was disabled from the start... and I tried the Video Card at default clock, over clocked, as well as under clocked and the same issue resulted... as I said before it is NOT the video card.
There are two other things I could try is use my old Geforce4ti 4200 and see what happens... or even try out WindowsXP 64-bit edition as someone earlier suggested. I wish I could find a new BIOS for my XFX 6800NU, but there there is only the revision 1 BIOS that I was able to find. The mystery continues...
The GameMaster...

MSI Neo2-FR Power (JFP1 and JFP2) connectors

Hi,
The MSI Neo2-FR manual on page 2-16 list the pin assignments for the front panel switches and LEDs.
Questions: Are the white wires considered the negative wires and the color ones considered the positive ones?
Does anyone know if the illustrations used on page 2-16 of the MSI Neo2-FR motherboard manual have any errors in them, such as, incorrect label of positive and negatives pins?

Quote from: Eagle Rock on 21-February-08, 07:36:50
Hi,
The MSI Neo2-FR manual on page 2-16 list the pin assignments for the front panel switches and LEDs.
Questions: Are the white wires considered the negative wires and the color ones considered the positive ones?
Does anyone know if the illustrations used on page 2-16 of the MSI Neo2-FR motherboard manual have any errors in them, such as, incorrect label of positive and negatives pins?
They forgot to give the polarity for the power led in the manual for JFP1 and JFP2. If you look very closely at the colored plastic around the pins on either connector the + pins are marked with a + in the plastic.
And as Del UK said normally white or black is negative and colors are positive.

SHARED MEMORY AND DATABASE MEMORY giving problem.

Hello Friends,
I am facing problem with EXPORT MEMORY and IMPORT MEMORY.
I have developed one program which will EXPORT the internal table and some variables to the memory.This program will call another program via background job. IMPORT memory used in another program to get the first program data.
This IMPORT command is working perfect in foreground. But it is not working in background.
So, I have reviewed couple of forums and I tried both SHARED MEMORY AND DATABASE MEMORY. But no use. Still background is giving problem.
When I remove VIA JOB parameter in the SUBMIT statement it is working. But i need to execute this program in background via background job. Please help me . what should I do?
pls find the below code of mine.
option1
EXPORT TAB = ITAB
       TO DATABASE indx(Z1)
            FROM   w_indx
            CLIENT sy-mandt
            ID     'XYZ'.
option2
EXPORT ITAB   FROM ITAB
TO SHARED MEMORY indx(Z1)
FROM w_indx
CLIENT sy-mandt
ID 'XYZ'.
   SUBMIT   ZPROG2   TO SAP-SPOOL
                  SPOOL PARAMETERS print_parameters
                   WITHOUT SPOOL DYNPRO
      *_VIA JOB name NUMBER number*_
                   AND RETURN.
===
Hope every bidy understood the problem.
my sincere request is ... pls post only relavent answer. do not post dummy answer for points.
Thanks
Raghu

Hi.
You can not exchange data between your programs using ABAP memory, because this memory is shared between objects within the same internal session.
When you call your report using VIA JOB, a new session is created.
Instead of using EXPORT and IMPORT to memory, put both programs into the same Function Group, and use global data objects of the _TOP include to exchange data.
Another option, is to use SPA/GPA parameters (SET PARAMETER ID / GET PARAMETER ID), because SAP memory it is available between all open sessions. Of course, it depends on wich type of data you want to export.
Hope it was helpful,
Kind regards.
F.S.A.

Problems with 10.4.9 and USB memory stick??

Since I've updated to 10.4.9 I'm having nothing but grief when using my Memorex USB 1GB memory stick. I use it for backing up crucial files (e.g address book, etc.)
Now, when I attempt to copy files to the memory stick, the system goes into an infinite loop (spinning beachball forever) -- even all night long, even though the files I'm transferring aren't very big. Some of my files copy, but some don't.
This has happened three times now. The Finder is "not responding" and won't even let me do a relaunch -- I end up with a blank screen with a corrupted menu bar. The only thing that gets me going again is to Power OFF, twice!! After the first power off, pause, power on, I just get the Apple logo and spinning spokes. Soon the fan comes on full force in the CPU. Runs forever. So, power off again, pause, power on and this time the start up is OK, my desktop etc. all appear OK. (I remove the memory stick before powering on).
On the latest attempt, I had to power off and on three times before things were OK.
I erased the memory stick to start fresh, but still, the same problem -- and infinite Finder loop when attempting to copy files over. Lots of available space. Some files/folders copy. But when I simply try to open a folder on the stick, ....the infinite loop again.
What's going on??!!________

The repetitive powering off and on has resulted in a damaged drive directory and/or corrupted system files. Although you can try repairing the hard drive I suspect you will have to reinstall OS X.
Try this first:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now shutdown the computer for a couple of minutes and then restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger) and/or TechTool Pro (4.5.2 for Tiger) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
If this doesn't help (and I don't think it will) but the hard drive is repaired and OK, then you can reinstall OS X by doing an Archive and Install which does not erase the drive:
How to Perform an Archive and Install
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.
If the hard drive cannot be repaired then you will have to erase the drive and reinstall OS X.
Why reward points?(Quoted from Discussions Terms of Use.)
The reward system helps to increase community participation. When a community member gives you (or another member) a reward for providing helpful advice or a solution to their question, your accumulated points will increase your status level within the community.
Members may reward you with 5 points if they deem that your reply is helpful and 10 points if you post a solution to their issue. Likewise, when you mark a reply as Helpful or Solved in your own created topic, you will be awarding the respondent with the same point values.

IPhoto Pics - Sony ProDuo Memory Stick Problem

I have a Mac mini. Using a Sandisk Micromate Reader to plug a Sony 4 GB ProDuo Memory Stick into the USB port, I transferred ~200 jpegs from iPhoto to the memory stick's DCIM folder and could see them just fine via my computer after the transfer. But when I mailed the memory stick back to my son, he not only couldn't see any of those pictures I'd downloaded--but also could no longer see the pictures he'd taken and sent me. He says the memory stick appears empty, but I know it's not. What does he/I need to do so he can see them both on his Sony Cyber-Shot camera and a computer? Thanks.

This is not an iPhoto issue but a general operation issue or a Sony issue
In general camera's require a very specific format for their memory and if there is some small error in that the camera does not see the photos - If you want to send photos to him I suggest taht you simply export those photos to a desktop folder and drag that folder to a cleanly formatted memory stick = he should be able to load those onto his computer -- he will not be able to see them on his camera - to do that you need to work with Sony support to get the required format exactly correct
LN

PSP Memory Stick problem

Hi,
Every time I connect my PSP to my iMac the PSP folder on the memory stick gets erased and I have to reformat the memory stick. It even happens if I put the memory stick in a card reader?
My PSP has firmware 2.7
Any ideas?

Anyone have a similar problem or a solution?

Invalid Serial number and RAM memory upgrade problem

1. Please, I am trying to reinstall Snow Leopard, at the end is coming
"Invalid serial number entered Setup requires a valid serial number. The serial number has the format XSVR-106-x-xxx-xxx-xxx-xxx-xxx-xxx-x!
but my serial number is:
C07XXXXXXXXX!
What is wrong?
2. When I try to install 1 DDR Kingston 8GB PC3 10600 CL9 204-PIN SODIMM is coming a clicking sound, What is the problem?
Thanks.

All OS X Server 10.6 purchases include a product serial number key, and this serial number key is a required part of the OS X Server installation. This is a product activation key, and as shown in the display this key begins with XSVR-106 for OS X Server 10.6. This key was included with the paperwork from the original purchase on a couple of stickers on a card, if this system was acquired with OS X Server 10.6. If this OS X Server 10.6 media was acquired from elsewhere, then look for a sticker with the media and packaging. Otherwise, please contact the vendor and ask for the serial number for the media you've acquired. If you've purchased this Mac Mini with OS X Server 10.6 from Apple directly and no longer have the key, then you'll want to contact Apple Support for assistance.
As for your second (memory) question, presumably the memory is not compatible with your particular Mac Mini, or there's a problem with the memory itself. There are usually tech specs available listing the particular requirements for the memory for a particular Mac Mini system. If you purchased this memory from Kingston specifically for this particular system, contact the Kingston support folks and ask for assistance.
If you post the specific model of Mac Mini, somebody here can probably locate the memory requirements.

Neo2-PFS Platinum Edition and LiteON CD-RW Problems

Hi,
I have a Neo2-PFS motherboard and I can't get my LiteON CD-RW to work.
When the computer is not overclocked it takes about 5-6 minutes to burn a CD at
48x and the read buffer jumps from like 20%-100% constantly. When I overclock my computer I can't burn at all, I get bad disks. I'm using Nero 6 Ultra Edition. I have tried Fireburner but no luck. The burner worked fine on my Abit BE-7 mobo
even when my computer was overclocked. Could it be a problem with a burner? When it was working fine it took less than 3 min to burn a CD at 48x.
Thanks for any help,
Mario

Well one of the "Side-Effects" of Overclocking the FSB, is Possible HDD Errors, Loss of Data, All around Instability, And Dead PC , OK, Bad Joke, But True, so I dont see Having Underrun's, or Buffer Problems, when Burning a CD/DVD, While your System is Overclocked as anything Abnormal ...When Running Just about all the Componants "Out Of Spec", You Should expect some Negative outcomes, Especially when It Comes to Copying or Reproducing Data...Now for the Reason it is Not Burning Correctly while at Default FSB Speeds, is another Story Completely, Have you Trie another Utility Besides "Nero 6"?...Do you have the Latest "Lite-On" Firmware, from their Site?..........Sean REILLY875

K8N NEO4 Platinum-SLI - 4 Memory Sticks?

I read somewhere that there was a problem when populating all 4 memory slots with this board. Is that true? I'm not overclocked and I want to add 2 more matching 512mb sticks of curcial memory to the 2 already in there. I just thought I's ask before I spend. Thanks.

Quote from: syar2003 on 24-May-05, 06:39:03
Hi!
It's not correct to use the word single sided /double sided when it comes to this matter of the A64 cpu's
memory controller .
SD/DD is short for single density and double density .
It's upto how memory controller and chipset see the memory .
This is a sisoft sandra report on the memory of 2*512MB modules.
It has to do with banks . single bank or double bank .
The modules migh be double banked even if all is physically mounted on one side of the mudules .
Usually this only means they have used larger dimm chips in meg size and need fewer to make out 512MB total.
The correct thing to do is to find out the bank organisation of your modules .
If the banks are organized to be two 256MB density on a 512MB module it's double bank (nomatter how it looks physically).
If they are shown as four with your current crucial modules you are in the same boat as others .
You will find out this by using sisoft sandra and probably some other utilities too .
Let me repharse then. If I have 2 banks containing only 1GB, then can I add 2 more identicle banks and still be able to use them in duel mode at at 2T?

MSI Neo2 nforce3 -- can't get USB 2.0.

Hi guys
be gentle with me, Im a newbie.
Have just had my chip, memory and board replaced under warranty and have MSI Neo2 nforce3 with 3200+ and 1gb ddr. I have done all my windows updates, service packs, drivers from MSI et al and after hooking up my Maxtor One Touch am informed that it is working at reduced speeds as no high speed usb port is installed. I thought all this was done under the windows updates. I have tried removing the USB drivers and allowing windows to find its own drivers but no luck.
Are there any issues with this board that I should know about with USB 2.0.
I have also updated the board BIOS and can no longer see the setting to select as below, its no longer there, simply and enable disable switch.
OnChip USB
This setting allows you to enable/disable the onboard USB controller. Selecting
[V1.1+V2.0] enables the system to support both USB 1.1 and 2.0 spec. Setting
options: [Disabled], [V1.1], [V1.1+V2.0].
Any thoughts, much appreciated.

Was quite easy to do. Go along to www.bootdisk.com and make a Windows ME bootdisk (with CDROM support).
Then go to MSI and download BIOS (zip file) 1.9 for the motherboard. There are 4 files in the zip file including full instructions and what to type. Take note, there are special instructions there for xp users using the NTFS file system. You will end up with 2 floppy disks.
NB Instructions tell you to copy both files to the ramdrive. I simply copied mine to C:\ and it all worked out well.
Hope this helps.

Memory stick for msi km3m-v mobo

Hello all,
I'm asking on behalf of a good friend of mine who called me the other day to have a look at his pc as it was having a bad performance.
So I went to his place, saw that it was really going very slow, and opened the case to have a look at the components…
At first glance, I could observe a lot of dust and one memory stick of DDR 256MB at 333mhz.
I cleaned all the dust (looks pretty clean now), uninstalled all the unnecessary programs he had and decided to get him more memory, as 256MB (despite that he only uses his pc for e-mail checking, word and occasional websurfing) is not enough to improve the performance.
So I looked at the specs of his motherboard and found out that it only supports 333mhz. I found two shops here that still support this memory, only DDR 512MB sticks though at 333mhz.
Now the question is: Could it be possible to fit in one stick of DDR 1GB at 400mhz? Would the mobo adjust itself the clockrate to 333mhz so that the pc can run? Actually 1GB DDR memory stick at 400 mhz is cheaper than 2x512 at 333mhz What do you think guys…should I go for 2x512MB @ 333mhz or 1GB @ 400mhz
Also, I do not know which Bios version he’s using, I think that I won’t touch it as the system is running well and the latest Bios update is from 2004, almost as old as his pc.
But looking at the msi link from above I found that the Lan / Chipset and Sound driver indeed have updates, respectively from 2008 / 2007 & 2006.
Would you recommend to install these latest versions ? I think at least that the Lan driver makes sense…or?
Thank you again for reading this,
Best regards,
Koiishi

Hi Bas,
Thank you for your answer Don't worry, I won't touch the Bios , I wouldn't like to ruin a mobo which is not mine
I'll get then 2x512 MB DDR 333mhz, I also think that if the max FSB is 333mhz the memory should not exceed it. At least I think that my buddy will notice a significant peformance improvement with 1GB compared to 256MB DDR
Kind regards,
Koiishi

I am unable to insert the Memory Stick into the card reader slot on my HP 7510

I have three Photosmart 7510's (C311a) and one Photosmart Premier (C310a). All of these printers have the identical Card Reader slot on the lower, left front corner. ALL four printers will not accept a standard Sony Memory Stick from my Sony digital camera. In all cases, the slot has two layers for "DUO SD MMC" chips and each will accept the "Sony Memory Stick Duo" without the silver and white MSAC-M2 Adaptor. No matter what I try, the Memory Sticks will not even start to go into the slot. I have looked into the slots with a fiber=optic flashlight attachment and there appears to be no issues -- except, possibly, the separator between the upper and lower part of the two-slot opening, is a little above center in the opening. Sitting in front of the 7510, I can look into the slot and see a white or very light gray surface that is sided to side across the opening, just inside the opening. When I get down and look into the slot at about a 'flat' angle, the white surface does appear to be just high enough that it partially obstructs the lower slot -- all the way across the slot.
I have tried four Memory Sticks and two Memory Stick Duo's, with and without adaptor. NOTE that the Memory Stick DUO, when NOT in the adaptor, will fit right into the upper part of the slot. However, with the Memory Stick Duo in its adaptor, and all the other Memory Sticks I have, none of them will start inot the upper or lower 'bay' in the slot opening.
Any insight would be greatly appreciated.
MDC in TN

I think I will declare this discussion closed. In an earlier post I said I would need to keep working at this problem until I seized up the right setting. Well for my 1080ii XDCAM EX 35 timeline, I have alredy tried a number of settings. The source WWV is 1280x720. The problem is stuttering video losing every other frame, audio popping or audio continuously losing a greater amount of sync. I tried APPLE TV 1280x720 in Compressonr (I'm still making more, not all have been tested.) The Apple TV h.264 works. It has to be rendered. I know some will say that's not optimal. I have put a lot of time into this with no other good results so I'm accepting this for now. I might be cooking up another right now in Compressor that will work better. Thanks to the posters.
Chris

Satellite Pro P100-327: memory card reader does not read Memory Stick Duo

I just got a P100-327
http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/jsp/productPage.do?service=UK&PRODUCT_ID=121991&toshib aShop=true)
which, according to that page, is supposed to have "1 x 5-in-1 Bridge Media slot (supports SD Card, Memory Stick, Memory Stick Pro, MultiMedia Card, xD-Picture Card)" but the pdf user manual that came with it says that it does not support Memory Stick Duo, Memory Stick Pro Duo or mini-SD.
However, I have a Memory Stick Pro, and a Memory Stick Pro Duo in a Memory Stick Pro adapter and the reader can't seem to read either of them (they should both count as Memory Stick Pro which should be readable right?)
Should I be able to read my Memory Stick Pro cards? Why can't I since it says I should be able to? Do I need to install something first?

Hi
In my knowledge and according to the manual the Bridge Media slot supports Media of type
- SD Memory Card
- MultiMediaCard xD-Picture Card
- Memory Stick
- Memory Stick Pro
Please note that the Memory Stick and Memory Stick Pro are not the same as Memory stick Duo and Memory Stick Pro Duo.
Dont mix it.

Msi neo2 k8n 54g platium and 4 memory sticks problem

Similar Messages

Maybe you are looking for