MSI neo2 platinum problem, forced to reset BIOS everytime I turn on the PSU

I just got my neo2 platinum mobo. Everytime I switch it ON all the led's at the back (diagnostic) turn red/orange and never turn green.
I have to reset the bios everytime to get it to post successfully. (bios is the original bios, no flashes done)
Processor: 3000+ (939)
Anyone else have this problem? what causes it?
[update] the bios version is 1.3 which is the latest on the msi website
System Specs..
AMD Athlon 64 3000+ 90nm (socket 939)
MSI K8N Neo2 Platinum
1 GB Kingston HyperX DDR 400 CS2
SBlive
Nvidia GeForce4 Ti4200 128MB MEM
Logitech MX510
1x80GB WD HDD with 8MB cache
1x120GB WD HDD with 8MB cache
Lite-On 48x CD-RW
NEC 16X DVD RW Drive
RAIDMAX Black Aluminum Gaming Case with 6 case fans and 420W PSU

I think the power supply may be the problem
Once you reset the bios you don't need the amps to spin up the drives, as they are already spinning, saving you about 3 amps I bet. If the newer bios doesn't help, try unplugging half those case fans, the non boot drive, and take the cd's out of you optical drives so they dont spin up, then try cold booting your box a couple times. If it works you know you need a new power supply.
If it doesn't perhaps you've got a grounding problem? Are you positive that nothing metal is touching your motherboard where it shouldn't? If that isn't it, Id assume the cmos never really clears, and then take the battery out of the motherboard for a good hour while the power supply is unplugged, then give it another shot. I've seen a bunch of DFI boards do weird stuff like that before, the exact same thing actually. Nvidia has a few odd issues with the nforce chipsets and the cmos.
Oh, since you asked, 3000+ is 1.8 ghz. It will probably run at 2.4ghz easy (1.4 volts), thats a 90nm chip

Similar Messages

MSI NEO2 Platinum, problem with mouse Genius PS2 optical

Hello,
I have a MSI NEO2 Platinum motherboard with a mouse Genius optical PS2. When the S.O. init the mouse is not detected, I unplug and plug again the PS2 port and the mouse work perfectly ! ... The mouse is working perfectly, I test it in another PC, the problem is the motherboard !
The same situation is on Windows XP Professional and Linux Ubuntu 5.10.
Please help me, thanks for your attention !
Raúl.

Raúl,
The PS2 slot is NOT a hot plug! If you remove and reinstall it while there is power to the mobo you stand a very good chance of destroying the PS2 Slot.
Take Care,
Richard

New Msi Neo2 Platinum....many problems

Here`s my setup:
A64 3200 939 winny watercooled
Msi Neo2 Platinum bios ver 1.4 vcore 1.50 HTT x4
2x512 corsair xmspc3200xlpt timings 2.5-3-3-7 1T vdimm 2.85 235x10 fsb 1:1 in the first 2 slots next to the cpu and tried the last 2 also
BFG 6800 GT OC 256mb 1.65 volts
SB Audigy 2 zs in the third pci slot
80 gig Maxtor
80 gig WD SE
Truepower 550 about 2 yrs old 12v amps are rated at 24a
6 case fans
waterpump is on the 12 volt rail
VC is on its own rail or leg
hdd`s and floppy are on thier own rails or leg
Fans and water pump is on its own rails or leg
Cd rom and burner is on its own rail or leg
i ran memtest on my on my sticks seperate and together and passed at 250 fsb 1:1 for 5 hrs and they are a matched set
im getting random errors,device driver errors and crashes in HL2 and in 3dmark05 and in 03 i get as high as 2500mhz and my rig reboots itself tried changing ram timings to 3-3-3-8 and no change
curious my psu not enough for the job amp wise ? i checked my 12v5v and 3.3v rails with a dvom and im getting 11.96 on the 12v rail under load, 4.98 under load and 3.28 under load but the bios reads about .20 to .27 under what my meter says
this psu ran flawless with a NF7-S ver2 ,barton xp2500 mobile@2477mhz and a 9800 pro
im new to the board but not new to o/cing and this board has me baffled any ideas would be helpful

Sounds like you are suffering from the NF3 + 6800 combination problem.
Theese things that gives troubles are dx9 it seems.
Interesting thread:
NF3 & 6800(series) compatibility ???

MOVED: [Athlon64] Msi K8N Neo2 Platinum problems with Patriot Ram

This topic has been moved to AMD64 nVidia Based board.
[Athlon64] Msi K8N Neo2 Platinum problems with Patriot Ram

First post, whoo hooo
So what version of BIOS are u running? I recently installed the two newest versions 2.0 and 2.1, and they both give me problems. With the latest (2.1) I'm getting the same error as you. Returning back to previous BIOS fixed my problems. Oh yeah, my RAM is Kingston Hyper-X, so i don't think thats your problem.
Let me know if you fix it, thats why im here, .

Msi neo2 platinum / venice 3.2 start up issues!!

hello people,
I´ve recently bought and neo2 platinum and a a64 venice, but I´m having problems with the boot up.
problem: when a turn on the psu swith, (without presing the power botton of the case), the sistem turns on for itself. It doesn´t boot, just turns on, so I have to press the case botton to do so.
technical data:
msi neo2 platinum, bios updated to 1.9
a64 939 venice,
2x256mb ocz performance rev.2 pc3200
psu antec true control 550, or topower 400w.
hdd seagate 80gb sata1,
msi fx5900vtd,

Quote from: hull01 on 15-August-05, 09:46:20
thanks for your help, but it´s still doing it, the cables are all well conected, right now don´t know what I´m gone do, may be try with rma
I'm sorry, I wasn't clear. Your mobo manual will have at least two different LED connections. Only one is correct for your case. To make matters worse, it's possible that your mobo LED pins and your case LED connectors aren't color coated. The mobo I have (Neo 4 Plat) was like that. My Power LED switch on my case was different that what the book showed. If you have it plugged into the green area on the mobo then try the black area for the Power LED. Now if that doesn't work then it's something else. Remember after you plug it into the black area, remember to reset your CMOS as before.
If that doesn't work, did your board come with a D-bracket? The little bracket with LED lights on it used to diagnostic utility.

MSI Neo2 Platinum (Winchester3200) - strange instability issue in Windows

My specs:
Winchester 3200 CPU
MSI Neo2 Platinum 1.4 bios
2 x 512 Kingston PC4000 3-3-3-8-1
Gainward 5900Xt GS
Seagate 160Gb SATA on SATA port 3
The problem seems quite odd to me, so I decided to post here. Generally, the PC is stable, passes more than an hour of Prime95, 3d marks run fine etc.. but in Windows (XP Sp1) I'm getting this annoying issue: when I let the system run idle for a while, with none or some windows open but no programs active, my computer literally freezes. I can move the mouse, but i can't open any windows or click any buttons. Still, the keyboard is responding so I hit ALT + CTRL + DEL and get the Windows Security window. There I click on the Task Manager and all i get is an empty desktop, with the wallpaper but no icons or any activity whatsoever.
Any suggestions? Thanks in advance.

Quote from: Lorex on 10-March-05, 21:43:00
Nope.. And I hardly believe it's a software issue. Will try a fresh install of XP today, nut the reason of such strange behaviour escapes me :] Cmon people, any ideas ?
If you problem isn't related to software, then the only other thing that comes to mind is that overclocking is the culprit. I'm not overclocking anything (except my 3d card, and that only slightly) and have no such problems with my K8N Neo2. You describe a strange problem, certainly, and in my own experience such behaviors--system runs great in some normal situtations but in others it doesn't--have always been related to overclocking of some kind. If you aren't overclocking anything then it's probably software induced. Good luck!

915P Neo2 Platinum problems

I'm hoping someone will be able to help me as I've been tweaking bios settings for 3 days and not managed to get anywhere with this.
I've have the following:
1x 915p Neo2 Platinum Mboard
1x Sapphire x600 235MB Graphics
1x Corsair PC2-4200 512 MB DDR2
1x 40GB Western Digital IDE drive
1x 30GB Western Digital IDE drive
When I first switched it all on, the board powered up but I got no display and no beeps. After pulling out all wires and adding the minimum of devices I got it to start up properly and got into bios. Eventually, after tweaking some settings and then systematically adding each device in turn I got everything connected whilst maintaining stability so it would still boot up.
Next problem I has was that it wouldn't boot from a floppy. It kept giving me "Disk I/O error". I tried several different floppy disks - same problem. I changed the floppy cable and still got the same error. I then bought a new floppy drive and tried that but still got the same problem. Decided to carry on and install XP incase floppy started to work later.
When installing, I pressed F6 to load RAID drivers. I selected the IDE RAID driver, it chugged away and carried on loading setup. My 2 IDE drives were successfully identified and I selected the installation drive and formatted it (tried quick and full format), after it had done this, it then tried to load the RAID driver again from the disk. At this point, the driver disk is still in the floppy drive, but it then says that it can not load the file from the disk and to try another. Again I tried several disks all of which gave the same problem.
I've searched this forum to help me with my earlier issues and found answers but couldn't find any info on this one. Can anyone help? I'm starting to think that my mboard has a poorly floppy controller. Also, I've got completly confused about the RAID setup, I currently have both my drives, 1 as master and 1 as slave, in IDE2 and have not touched the RAID BOIS setup - does this mean I will still be able to use these as 2 different drives? Eventaull I will add SATA RAID.

Quote
Originally posted by Del UK
Hi Masjj,
Could list some details of the PSU you using please, as this would help. Please see sig below as a guide.
Confirm please:
You can boot and format, then when install happens, failure????
Del
My spec is as follows:
No OS yet
- tried Win XP (blue screen after RAID driver load)
- trie Win XP with SP1a ("can not load viaraid.sys" error after disk format)
MSI 915P Neo2 Platinum (MS-7028 Ver 10A)
BIOS - Shows "915P/G NEO2 A7028IMS V1.0 05/27/04" on first screen, in BIOS setup screen shows v02.56
Intel P4 3.0GHz PRESCOTT, 1MB L2-Cache, 800MHz FSB
Sapphire X600 256MB + 19" TFT
Soundblaster 5.1 Live card with LiveDrive
Western Digital 30GB IDE (Master)
Western Digital 40GB IDE (Slave)
Pioneer DVR-105 DVD/RW Burner
DVD-ROM
WD 800JB+CD-RW
1* Corsair Value 512MB PC4200 DDR2 Ram
PSU - eTech 460 +3.3v-28A +5v-30A +12V-30A
I cannot boot from Floppy, can boot from CD. When I try to install WinXP with SP1a, I hit F6 to load RAID drivers, choose driver from list. Setup then detects HDDs, I format install drive, then it tries to load RAID driver again from disk and gives a fail message of "unable to load VIAMRAID.SYS" and will not continue. If I try to install without RAID drivers, it says that there is no storage device connected.

MSI Neo2 Platinum should beep if the cpu is dead?

I have a Neo2 Platinum and a 3500+. When I try to start the computer the fan starts to spin but the monitor is black. The computer doesnt make any beeping sound. I know its either the CPU or the motherboard that is broken. Should the motherboard make any sound if the CPU is dead?
My D-bracket says "Early Chipset Initialization" and "Bios Sign On" (shows info about logo, cpu brand name etc..)
Depends on how I start up the computer (psu power switch or button)
The problem started a few weeks ago. The computer made lots of reboots and now I cant even access bios. Ive replaced all other components (ram,psu, HDD) but nothing happens. So is there any way to find out if its the motherboard or the cpu?

Quote from: bennyfax on 25-October-06, 07:59:57
Ok thanks for trying to help me but its not the HDD's. Its the motherboard or the cpu. I just dont know which one.
your CPU is not dead for sure.
try barabone setup,(leave only basic parts which is necessary to boot) and Clear CMOS Guide(remove power cord from PSU before proceed).
test with one stick of memory only.

BSOD using MSI NEO2 platinum

Hey.. i reg for this forum just for this screw up prob.. heres my spec.
SilverStone:
AMD64 3500+ 939 with xp90 | MSI Neo2 Platinum mobo | 2 x 512 Cosair TwinX ddr400 ram with heat spreaders | Sapphire x800 pro with artic silencer 4 vga cooler | SB audigy 2 with gold input jacks connected with Creative Megaworks 5.1 550 | TDK 1616DN 16x DVDrw | Pioneer Slot in Drive A106 | Samsung LCD 172x | Antec 550W Psu | SilverStone TJ03 Full Tower Casing
Been having unexpected BSOD and reboots my system after the screen comes out . i am trying the settings for the memory as stated in the corsair website . hope it turns out well .. i had used memtest on the default settings of 2 2 2 5 or something and goes well but not in winxp pro .. will restart due to BSOD. any ideas ?

what slot do yu mem fitted on?
there is only 1 combination that seems to work with that board ( i have same board) fried but,,
slot 1 and 2 green ( 1xt from bottom and the SECOND ONE pURPLE)
thats looking at the board fitted in the case . slot 1 is the bottom one).
tHE BOOK SAYS THAT 1 AND 3 WORKS TOO BUT IT DIDNT( its for DDR 333). TRY THAT.

MSI neo2 Platinum Instability

I just got my whole new computer setup within the last few days. The problem I have come to now is that my system pretty much randomly reboots itself every so often( like 1-5 hours). I've had this happen both while the system is under load being burning a dvd and also when i'm just surfin the net. One of the first things I did was to flash the bios to version 1.4 before i installed the os. I also read a guide that I saw someone post on here about the settings for the neo2 motherboard and adjusted what was needed accordingly and checked that my bios is set about the same for stability. At first I thought it was just my video card screwing it up as when I put the system together it was with a very old card but then I got the new one and the same thing keeps happening. Then I thought it may be that my windows installation was corrupt or just a bad one so i formatted my drive and redid the installation, but to no avail, I still got the same random reboots. The temperature readouts in the bios are 37 for the cpu and 30 for the case so i don't think its overheating or anything. I am wondering if anyone has experienced similar problems or knows of this problem and can lend a suggestion to what the problem is.
My setup is as follows:
MSI K8N neo2 Platinum
AMD 3500 90nm
1 gig OCZ pc3200 platinum rev. 2
ATI All-In-Wonder 9800
OCZ 420 watt power supply
western digital 74 gig raptor
thanx for the help
Freak

Quote from: Wonkanoby on 25-February-05, 16:05:09
turn of auto matic reboots so you can see the bsod
and post stop code and any driver etc it blames
Memtest86
I'm not sure how to turn off automatic reboots. I only see the blue screen for literally a split second just before it reboots.
I'm using WinXP btw and have all updates installed incause that matters. Anyway everytime it restarted in the first install it used to blame the video driver but with this new second install of windows i have a different video card and different drivers so it doesn't say "device driver wrong for video card(or something similar) anymore. Now it says pretty much the same thing but doesn't limit it to the video card, it just says device drivers are wrong or something like that.

K8n neo2 platinum problems

ok guys I've been looking all over the internet and cannot find any answers to my problem.
I have an MSI K8N neo2 platinum running easybios
AMD Opteron 146
2gb Ballistixs pc4000
30gb maxtor
120gb maxtor
2x dvd rw drives
nvidia 6800 agp
sound blaster live 24bit
I run windows x64 and after flashing my bios form 1.6 (I think) to 1b I kept getting errors e.g. "ROM cannot invoke" (or something), and primarily "disk read error", now the disks show up in the bios, they show up in a windows install but it just won't boot from them. I have flashed to easybios and the rom error went away but the disk read one was still there. I am now reinstaling windows x64 but would like to know how to fix such a problem if it were to happen again. Both my drives are IDE and are on the IDE0 cable with master and slave correctly set.
Also the temperature readings for my processor are 42 degrees celcius when everything is at stock and I have a zalman 9500 heatsink fan on it running at full speed. This is obviously wrong - is there any way to fix this?
Thanks
Daven

I has the exact issue with my board, except it was with the SATA drives. I flashed with e few BIOS', and the newest one that worked correctly was 1.8
If it was me, I would reflash to BIOS 1.8
Post back with your results.
Also, even though you are installing Windows again, it will most likely corrupt your installation, as it did mine, twice, before I figured out the problem.

Serious K8N Neo2 Platinum Problem

Hello
This is my long and sad story with this MSI board...
As I mentioned above, I have a K8N Neo2 Platinum with a Athlon64 3500+ (130nm) and some Corsair TwinX 3200XL 2x512 MB. The recommended setting for this Ram is 2-2-2-5-T1, but with this setting, my system crashes in prime 95 after maybe 5 mins and under compiling a Gentoo-System. But on the other hand, Memtest 86 reports no error at all with this timing. Later I changed the Timing to 2-2-2-5-T2 and suddenly, everyting becames stable. I could compile two Gentoo systems (32 & 64 Bit) and ran prime 95 for more than 24 hours. I have nothing overclocked. I think the Board is the Problem here, because there are some other malfunctions. Sometimes it doesen't detect my IDE Devices at startup (DVD-Rom and CD-rw) or my ethernet card gets no connection, but everything is configured well. So I really dont know what to do. I feed my Memory with 2.75 Volt. I also flashed the mainboard to Bios-Version 1.3 but nothing changed...
I hope anyone of you can give me a hint or something...
Thanks a lot

corsair ultra-low latency requires 2.75V according to their documentation. Also I have heard that prime95 has an issue with systems with 1024mb or ram in a certain test. Not sure I can't confirm but I do remember reading that somewhere yesterday.

Numerous K8N Neo2 Platinum Problems -- Argh!

I am experiencing numerous problems that are mentioned on this site:
1) Unplugging the power cable, plugging back in and turn on the Power Supply switch and then the whole computer turns on and hangs with a black screen. I then have to turn the computer off/on on fron switch.
2) Occasional Hanging at detecting IDE devices
3) Sometimes losing USB Keyboard and mouse while in windows or rebooting. Taking several reboots to fix. (I removed my antec sonata front USB header per other posts and we will see the results)
For issue 1 and 2, I have not seen solutions. But......
I run SpeedFan 4.18 and notice something disturbing: VBAT reading 0.00. Does anyone know if the VBAT reading is reported using SpeedFan? Maybe it just does not read it but with some of the problems that appear to be a battery problem (Like #1) this concerns me.
Are others able to get the VBAT readings?
Perhaps I have a dead battery? Thus when removing the power I lose the settings on the Mobo to not turn automatically one when the power plug is removed?
I am using 1.3 BIOS, I just got the motherboard yesterday and have been fiddling with it for about 10 hours.
* Athlon 3500+ (Not 90nm)
* 2 512MB Kingston KVR400X64C3A modules in DIMM 1 and 2. (What would be the memory settings in bios to use? Currently it is all AUTO)
* Antec Sonata Case with 380w power supply
* Rear 120mm fan blowing out, front 120mm fan taking air in.
* WD 74GB Raptor SATA
* WD 120GB 8MB Cache EIDE
* TDK 840G DVD/CD Writer
* ATI Radeon 9800 Pro 128MB
Everything else I use onboard.
When I first installed the DBracket showed all 4 red lights (CPU bad) but after a CMOS refresh that went away. It happens sometimes when I unplug it from the power cord.
Any insight you can give on any of these issues is appreciated.

Thank you for your reply.
I did check the BIOS and the VBAT is showing voltage. So I assume the battery is good. I have seen the problem with the power switch being turned on from the PSU and the system just starts up (though it should not). Then, only after turning off with the case front power switch does it resume normal operation. This is only after unplugging it from the wall.
Since the batter has voltage, it is odd that things get messed up when unplugging from the wall. Any possible resolutions at this time for that?
I am afraid of BIOS upgrades but I am willing to give it a shot if it has the possibility of straigtening out this system. I need to work quickly though cause I only have 7 days to return this board. I am considering a different brand, but I want to give MSI a shot. I have always been a ASUS user and never had problems in the 6 years I have used the boards.
I will try the USB fix, I will let you know the results.
I have not had the IDE issue as of later because I do not unplug my system from the wall. But I am afraid if I lose power and I am not here that the machine will turn on and then sit there all day with 4 red LEDs on the DBracket. Then is when I also will get a IDE detection problem which requires a reset once, maybe twice.
Quote
Originally posted by Supershanks
Sorry DazedConfused, posts crossed.
your power looks ok then.
Beta bios are here K8N Neo and Neo2 Bios Collection. *Updated 151 for Neo2*
Don't think it would really help at moment though. Leave till later if you want, lot of pps stick with official ones & run fine.
Quote
I believe the timings were 3-3-8-3 1T
there ok
If you want to alter them go into bios - Cell Menu - Dram Settings ,
see Dram Settings for help
Quote
2) Occasional Hanging at detecting IDE devices
It may be worthwhile whilst your trying to troubleshoot , unplugging your 2nd HD
Unplug drive - see if that helps
If not go into dram settings & change the 1T/2T to 2T - This will slow the SDram command rate and may help
Take a deep breath - chill It helps
luck

MSI X48C Platinum problem

i have a MSI X48C Platinum
Ram: OCZ PC3-12800 Gold RAM - 4GB, 2x2GB, 1600MHz, DDR3, Low Voltage, Dual Channel
Processor: Intel Pentium D 915 2.80GHz / 4MB Cache / 800MHz FSB / Dual-Core /
PSU: thermaltake 420w
Problem: i turn the computer on it sounds like its going to start up then turns off for 5 seconds then comes back on and dose the same thing over and over. if i hit the button on the back of the motherboard it will boot and say CMOS Settings Wrong, CMOS Date/Time Not Set, Press F1 to Run Setup Press F2 to load default values and continue if i click f1 it will go in to bios and if i click f2 it will load windows.
any help??

Quote
sorry i dont know what you mean when you say amperage limits (A) on the +12V voltage rails
Look on the PSU sticker. And write down the numbers.
Quote
ok i got it to boot but it dose the same thing
Did you do this?
Quote
Manually set the memory clock speed to DDR3-1066 for testing and see what happens.

MSI k9a Platinum + PowerColor 1950 pro extreme + bios v1.6

Hello! At motherboard stood version firmware v1.4 Run test 3DMark2005 and received 10,444 importance to my configuration (which is a good figure). Then Live Update pointed out that there are newer BIOS v1.6, I flash. Then began receiving in 7048 3DMark2005 :( Tried to reinvent the windows XP, set new driver, not helped, Clear CMOS. ReFlash to version v1.3 (why not found on the website version v1.4), and miracle! 3DMark2005 shows 10456 . It can be concluded to reduce speed blame new BIOS. So do not recommend placing Edition v1.4 above.
Sorry for my English. I used a translator from GOOGLE
AMD 5200+ windsor
MSI k9a platinum
PowerColor X1950 PRO Extreme 256MB
DDR-2 1Gb 800 Elixir *2
Western Digital Serial ATA II (WD3200AAJS) - 8Mb, 7200rpm
Chieftec LBX-02BBSL 450W

Here we go AGAIN, I will explain this AGAIN .......
Do not flash the bios if there aren't any problems!
Flashing the bios is only usefull if you experience compatibility problems between certain hardware devices in your pc. So, leave the bios alone!
A BIOS IS NOT A DRIVER!
And, like it is with drivers, newer is not always better! Some driver/bios are meant only for newer hardwaremodels.
LEAVE IT ALONE, UNLESS YOU ABSOLUTELY NEED TO MESS WITH IT.
So, Foxyrus, lesser points in 3DMark was completely your own fault, not MSI's. Telling people not to use the 1.6 bios is nonsense. In your case it did not work, but for some folks it probably will work.

MSI neo2 platinum problem, forced to reset BIOS everytime I turn on the PSU

Similar Messages

Maybe you are looking for