MSI NF750 G-55 AM3 DDR3 EZ OC switch problems please help

I bought an MSI NF750 G55 AM3 DDR3 about a few months ago (i tried unlocking a AMD phenom II 550 BE which failed) other than that with my new AMD Phenom II X4 955 BE was working and when i got curious i tried to turn the OC switches it ran fairly well with 20% speed increase between the ram and CPU but became unstable about 3 days after (temps were all fine and normal) in the sense that my computer started randomly powering down so i turn the OC switches back to the default location and i have had computer shutdowns as stil. it only does it when im putting my computer under load though . (no data loss) i even restored my bios defaults and CPUz says my clocks are back to normal but theres still some instability in my system i dont know where but if you could help me find out where the problem is i would be very greatful im also running the AMD Cool n Quiet option i dont think that would do anything though please help
Spec:
Mobo: MSI NF750 G-55
Ram: Corsair Dominator pc10666
GFX Card: EVGA gtx 260 core 216
CPU: AMD Phenom II 955 BE
PSU: Antec Truepower Quattro 850
CPU Cooler: Corsair h50
HDD: (ya i know i dont have SSD yet <_> working on other parts first) WD Raptor 74GB (bought when came out) WD caviar 140gb

Quote from: Henry on 23-June-11, 06:31:26
If you haven't done so already >> Clear CMOS <<
Already did >_< haha still havin problem

Similar Messages

  • MSI problems please help

    i have an msi neo plat and an 1mb clawhammer 3200 they both working fine
    i upgraded to a 3400 clawhammer and it wont boot i just get beeps..
    i thought hmm cpu died
    so i tried it in my other msi board [k8t800 chipset] and it works fine
    so i decided to try the 3000 a64 in the msi neo that doesnt boot either?
    it only works ok with the 3200 installed?
    ive tried about 3 different bios aswell
    please help

    Quote
    Originally posted by LoCk3H
    i have an msi neo plat and an 1mb clawhammer 3200 they both working fine
    i upgraded to a 3400 clawhammer and it wont boot i just get beeps..
    i thought hmm cpu died
    so i tried it in my other msi board [k8t800 chipset] and it works fine
    so i decided to try the 3000 a64 in the msi neo that doesnt boot either?
    it only works ok with the 3200 installed?
    ive tried about 3 different bios aswell
    please help
    re-insert your memory to try again.

  • MSI GT70 0ND Problem please HELP

    Hi!
    Yesterday i was playing Diablo 3 and my notebook just turned off and wont turn on doesnt react anyhow!
    I think its my videocard i tried a few solutions but it doesnt helped me! a part called
      u4 mps1222
     ms-1w051 ver 1.1
     is fried its the video card! GTX 675M where can i find it! please HELP or maybe there is other problems!

    If the video card is fried, there won't be much we can do here....BUT....
    Your best bet is an RMA. >>How to contact MSI.<<
    If it's not in warranty though, you're going to pay for it.....
    You could probably try removing the GTX675M and turning the laptop on without it, it might work without it, hard to say as I haven't tried to do that before.

  • MSI 645 ultra xp / 2000 problem please help.

    I've got 3 MSI 645 ultra mobos. I've tried every thing i can think off to get xp installed and working. I don't get as far as formating the hard disk in the setup. I relpaced the power supply with a qtec 550 watt power supply (the gold one). i've flashed the bios to 1.9, i've used different hardisks and cables. I've checked the memory PC2100 and 2700. It's a pentium 4 1.5, I've tried a 2g in it as well. I'm using an ATI radeon 7500 but have tried a s3 agp card. All the other components work fine in another machine but not on my 3 MSI boards.
    Please help some one out there must have had the same problem. I'll buy the first person who fixes it cakes!!!
    Ta
    Gus

    Hi,
    I ran memtest 3.0 and there were no errors. it ran for 9 hours.
    I am only using one hard disk at a time. it's set as a master on IDE1 and the CDrom is on IDE2 as a master. should I use cable select?? I also tried the hard disk and CD on ide2 and that did not work either.
    Ta

  • MSI K8N Neo 4f problems please help.

    My rig
    Processor
    AMD Althon64 3000+ Venice
    Mainboard
    MSI Neo4f
    Graphics Card
    Leadtek GF6600GT Extreme 128mb
    Memory
    2x512 Twinmos ddr400
    Display
    Viewsonic VX912
    Storage
    Hitachi 250GB SATA
    Optical Storage
    MSI DVDRom/ LG 4163B DVDRW
    Casing
    Cheapo
    PSU
    Verudium Vortex 430w
    Audio
    On Board
    OS
    Win XP SP1
    The above rig bought 3 weeks ago,
    and its been giving me unstability problems. After installing winxp SP1, when I start installing drivers, these problems would come.
    1. PC would freeze up now and then.
    2. USB keyboard and mouse sometimes wouldn't work after bootup although PC is still running
    3. Blue screen! now and then.
    4. Sometimes different software installation would give error but re-running the installation would be fine.
    The above mentioned problems could is still persisting after 2 weeks. I've reformat and reinstalled winxp 4-5 times and the above would still occurs sometimes, even in the middle of installing drivers. It comes randomly and not during a specific software/driver installation.
    I've run memtest and RTHBRIBL overnight with no errors and I'm suspecting motherboard. Strange thing is that the MSI live update program help me flash bios on my motherboard and would still prompt me I need to flash my bios everytime.
    I've basically almost isolate everything except motherboard. I hope someone can help me determine if it is my motherboard problems. I've going crazy already.

    Quote from: Tango on 14-August-05, 21:16:35
    Do you have Cool n Quiet enabled?
    If so disable it , and report back.
    Verudium Vortex 430w
    Please post the voltage rail ratings.
    Have you tried Prime95?
    http://www.mersenne.org/freesoft.htm
    It is a stress test that runs under windows and also can be used to test your memory.
    EDIT: http://www.alevtav.com/products.php?brand=1&ATSid=4a2fe5368de8eb29c5723c93b90aec9f
    If that is your PSU it is fine.
    What nforce drivers are you using?
    yes thats the vortex i have
    cool and quiet disable thru bios
    nforce drivers. seems to have more problems with the newer downloaded from MSI website. but can't really confirm
    I've download prime 95 but I did not run it because by running RTHBTIBL will cause my cpu temp to go to 47 deg c. But I'll try it tonight.
    note that I'm not running raid. just a 250gb SATA hitachi HD.

  • Nasty MOTU MSI / Modulation problem - please help!!

    OK, I've searched high and low for a solution to this, but no joy, so here goes...
    For weeks now, I've had an issue with MOTU's Symphonic Instrument.
    Parts recorded with it play back distorted if the active track in Logic's arrange window is not the one the plug-in is on.
    The 'distortion' is in actual fact the MSI playing back as if the modwheel is full on. It sounds like a very fast square-wave gate. Whipping the wheel back and forth back to zero while the MSI track is active will temporarily cure the problem, but as soon as you change tracks, it's back. It doesn't make any difference whether the plug-in is configured in single-channel or multitimbral mode.
    I've also had the same thing happen with Absynth, which suggests it might be more something to do with the way Logic handles CC#1 data from the Korg Kontrol 49. There are a number of reports about the buggy implementation of CC#1 on this controller, but they mainly concern it being used in Native Mode, which I don't use, as I need a working modwheel. Swapping the Korg out for a Roland PC300 keyboard controller had no effect in any case.
    It may have been caused by CC#1 events lurking around in the MIDI parts... some of them were originally recorded with Garritan Personal Orchestra, which uses the modwheel as a volume control. However, I couldn't find any such events, and although I might have got nearer to figuring out what's causing the problem, I can't get it to stop doing it.
    Inserting "CC#1 = 0" messages into the part's event list doesn't help.
    Recording modwheel resets on the same track doesn't help.
    Turning on the "Chase Controllers" preference doesn't help.
    Using a different controller keyboard doesn't help.
    Setting fire to the computer doesn't help.
    I am unable to perform the 1.1.1 update for MSI, so that doesn't help. The plug-in crashes Logic's validation with a "Fatal Error." This results in it being greyed out in the AU Manager list, and I am therefore unable to enable it manually. I'm currently swapping emails with MOTU tech support about this.
    If anyone can help resolve this while I still have some hair left to tear out, there's at least 3 pints of strong beer in it for them....
    G5 2GHz, 8GB RAM   Mac OS X (10.3.5)   Logic Pro 7.1.0, MSI 1.0.0, MOTU 828mkII, Korg Kontrol 49, bad headache...

    I would say do figure out how to make the upgrade first and foremost. A lot was done in that upgrade, and one may have been to fix this bug.
    As for cc data, have you checked the track automation for the track with MSI? I know it's an obvious question, but if there's ghost data it will show up there.

  • MSI GE70 2OE-029CZ Start-up problems, please help

    Hello guys. My name is Mike and I need some help from you. Half year back I bought notebook MSI GE70 2OE-029CZ from Czech Republic and it wont boot up now. I used this notebook normally without problems until now. Four days back I finished my work and turned notebook off. Next day, after I came back home, I turned notebook on and suddenly it turned off after 4 seconds. It showed only MSI logo, I did not get in to bootloader. Then I turned it on again and same thing happened again. Except it was running only 1-2 seconds. After this notebook did not start up again. I have checked power supply with voltmeter and got suitable voltage. I did let the battery to discharge little over night and in the morning I tried to put it on charger. The battery diode lighted up. But still could not start it up. I already filled out MSI Service webform yesterday, but still did not get any response. Im just posting it here if someone of you has some idea i could try. Also does anyone got any idea why are mine audio jacks not golden? They are just black. I supposed they had to be golden plated. Sorry for my bad grammar, I am not born English speaker . Thank you for you help and time.

    Hello,
    I am sorry you experience this problem and probably I would be frustrated if such a thing would happen to me.
    Sorry if I dis-read something, but have you tried turning the laptop ON without the battery just with charger? And other way around (with FULL battery but no charger)?
    About HDD: you can take it out, but would be BEST if you make backup somewhere once you take it out and send it TOGETHER with the laptop, as the problem might be somewhere with the wires.

  • MSI 648 max problems, please help

    Just put a new machine together and I am having some problems, hopefully someone can help.
    My machine seems to run pretty stable in OS, but dies when any game is played. It will crash anywhere from 2 minutes - 45 minutes in the game. Ive tried several games: C&C generals, unreal2, etc with the same results.
    Bios are updated and nothing is overclocked. Win XP is fully updated.
    Specs:
    MSI 648 max, 533fsb
    p4 2.4 northwood
    Seagate 80gig hd 7200rpm
    MSI g4 ti4200
    2 - 512mb pc2700 ddr333 dims (double sided)
    Antec 350w ps
    sb live
    48x liteon cdrw
    16x liteon dvd
    We are using a Kingwin KT-436S-WM case
    http://www.kingwin.com/product.asp?cid=15&pid=75
    It has a total of 5 fans with intake/exhaust
    HSF currently being used is the retail box HSF
    With the case sides on,  here are temps at idle after 10 minutes in OS:
    Proc: 136
    System: 91
    Vid card: 118
    With the case sides off, here are temps after running 10+ minutes in OS:
    Proc: 125
    System: 86
    Vid card: 114
    Here is the error that pops up (after crashing) when playing Command and Conquer: Generals:
    Technical Difficulties
    Sorry a serious error occured
    Thanks in advance

    Well my roomate cancelled the memory test after 12 hours, so I dont know those results.
    I do know that after removing 1 of the DIMMS, the machine seemed to be stable playing games.
    I sure wish MSI would have stated it only accepted 1 double sided DIMM.. especially when the reccomend Kingston ram, which is double sided......
    Me and my roomate BOTH bought this motherboard, while my roomate only bought 2 DIMMS of 512, I bought 3!!!!!!!!!!!!!!!!!!!
    So now it looks like we need to return these motherboards and get new ones... I HAVENT EVEN GOT MINE OUT THE BOX!!!!!!!!
    Any reccomendations on an MSI motherboard (or any) that support  double sided DIMMS? I am looking for 3 slots...
    thanks...
    Any other advise on how to get this motherboard to work with all this ram would help too, so we dont have to RMA through newegg....
    Anyone from MSI read this board?????
     X(    :O  ?(

  • MSI R4850 PROBLEM - PLEASE HELP FAST (UPDATED) :S

    I install my new PC and what do you know, there are exclamation marks on the POST and BIOS screens replacing some parts of the background... But when windows starts everything looks fine. I can watch movies and there is no problem. But then I saw this in the VGA driver tab:
    So I install a few games, and it is similar to that picture. The whole screen is covered with little squares on some spots and there seems to be faulty graphics.
    While playing a map in Warcraft, not only the graphics was like this, but every now and then the screen would freeze, go black and return to the same bad graphics. Also after 5 minutes it gave me a BSOD.
    I have the latest ati grafics drivers, and I tried replacing the 4850 with my old video card, an MSI Nvidia N7800GT and these problems are not present with that card, so it has to be the a problem with the 4850.
    So what is wrong with the VGA? Is it some hardware fault? What should I do?
    My system (only a day old):
    MSI P45 Platinum (Zilent) BIOS v1.0
    Intel Core 2 Duo E8300
    A-DATA Vitesta 1066+ 2x1GB
    MSI R4850
    1XWD RAPTOR 74GB
    1XWD CAVIAR 200GB
    1XWD CAVIAR 500GB
    1XSAMSUNG SATA DVDRW 22x
    PSU: Cooler Master Real Power M520
    HANNS-G HI221DP (22" Widescreen connected with DVI-D Single Link Cable)

    OK, so I tested the VGA in another system. And as it started it showed the exclamation marks in post again. Then I installed the drivers and i restarted, and the exclamation marks were gone. Then tested games, Warcraft and Crysis and everything works splendid. This was on my friend's PC which is:
    MB ASUS P5Q Updated to Latest BIOS
    PQI DDR2 800MHz 2GB
    CPU Intel Core 2 Quad Q6700
    HDD 320GB Hitachi 16MB cache @ SATA2
    Windows XP PRO x86
    So the VGA is ok here, but doesn't work fine on my system. Any ideas?
    EDIT: Updated BIOS version to 1.4 and the problem persists... some help pleaseee!

  • MSI Bundle problem (please help)

    I need your help. We have zenworks 10.3.3. I made a msi install bundle and bundle installs normaly, but remains pending. I checked the msi log and it says that it installed correctly. Last line is MainEngineThread is returning 0. Why Zenworks dont realise that the bundle installed correctly, what am i missing???
    Benny

    The fact status updates for other bundles, seems to eliminate the Status
    Roll-up as the root cause.
    Perhaps Reboot the Device?
    Maybe ZCM thinks the install is not yet complete?
    If you try to manually launch the bundle again, does it reinstall?
    If so that would tend to indicate ZCM thinks its not installed.
    On 7/26/2011 11:16 AM, Benius wrote:
    >
    > Thank you for your answer. When I made a bundle that just deletes one
    > file, it worked fine, this only happens with a msi (pending until I
    > remove the assignement). Also when I watch the ZENworks Progress window
    > it says installation completed. I know it is very difficult to help in
    > this kind of situations, but any tips on what to check?
    >
    >
    Craig Wilson - MCNE, MCSE, CCNA
    Novell Knowledge Partner
    Novell does not officially monitor these forums.
    Suggestions/Opinions/Statements made by me are solely my own.
    These thoughts may not be shared by either Novell or any rational human.

  • MSI K8T + AMD 64 Athlon Processor + Corsair 3200, can anybody please help?

    i recently have put together a system as follows...
    MSI K8T Neo Mainboard
    AMD 64 Athlon Processor
    Corsair TWINx1024-3200c2pt
    i experience random system crashes/reboots/lockups and sometimes on restart i get system message from windows xp saying that "this system has recovered from a serious error" and when i click to view the details of this error.. this is what follow..
    C:\WINDOWS\Minidump\Mini123103-03.dmp
    C:\DOCUME~1\robby\LOCALS~1\Temp\WER1.tmp.dir00\sysdata.xml
    **windowsusername
    i was wondering if anybody else has had any problems with this or perhaps if any of you know what could possibly be causing this.
    i have all the latest BIOS drviers, Motherboard drivers, and amd chipset drivers.
    can anybody help me with this?
    thank you.

    ok heres what i know i have corsair 3200 value select with the same system MSI K8T athlon 64 3200
    k just like 6 days ago i took out my motherboard and put in the rest of the motherboard risers the one by the ram had a plastic one in it and i put in all brass ones or whatever they are, and it started to bomb the  on me drivers not installing correctly and stuff like what you guys are saying so i just took them back out last night and im gonna reinstall windows again to see if it helps( i reinstalled windows XP pro 5 times yesterday by the way trying to make my Radeon 9800XT work properly with the drivers and have 8x and fast write enabled cause that was messing up also) and i finally got it to where i could install most the drivers but 2 of my hard drives are missing so thats why im reinstalling, windows wont allow me to install the driver in any way so it might be somthing with the risers on the board
    it was fine when it was missing the 3 on the end where the ide plugs are and i have my ram in slots 0 and 2 but that didnt seem to matter
    so thats just my experience to right now

  • MSI-KN8 neo4 Plat and windows booting issues...please help!!!

    let me start with my system specs:
    msi- 7125 plat KN8 (1B0 bios)
    amd 64 3500 venice
    1 GB (2 x 512 MB) corsiar valueselect (set at 2.5V)
    antec neopower 480W
    gigabyte nvidia 6600gt
    (2)  80 GB maxtor sata150
    250 GB maxtor sata150
    zalman 7700 series cpu fan
    sony dvd burner.
    Thanx in advance for any and all help i am, hopefully about to receive.  i read quite a few of previous threads and didnt find one with my issue.
    HERE GOES...
    this entire system was running with a different brand mobo (just upgraded to this msi-7125) and was running great!!
    however when i installed windows xp media center edition 2005, things where working great.  that is until i installed the nforce system drivers from the disk that MSI provided me. once i installed the ethernet driver,ide-sw driver, network controller the ask me for a reboot after install was done,  when the system restarted i got all the way the windows xp splash screen or loading screen.  at that point windows stops loading stays on the loading screen for about 10 minutes, then the computer shuts off.
    i have tried running memtest and had no errors, im positive that my psu is capable of handling my components.
    i'm really stuck on this one, any help would great thanx again!!!
    Sam

    You should be able to get into Windows through safe mode. From here uninstall the drivers and restart. You should hopefully be able to get into Windows normally now. Get hold of the latest drivers from the Nvidia web site and try them.
    Also check both Ethernet controllers are enabled in the BIOS.

  • MSI 6600 GPU and Neo 4 ultra problem ----- PLEASE HELP -----

    I just got done building a beautiful system with the K8N Neo 4 platinum matched with a MSI 6600 PCIE video card.  Everything went together perfectly.   After many reboots and getting everything set up the way I want, I accidently moved the monitor, and the DVI cable was loose.  I did this during a reboot.
    Now the system will not boot up at all past the post screen.  I can not get into BOIS at all.  I tried unplugging, clearing CMOS, and reseating the video card.  However, I am really out of options for what I can do.
    Does anyone ave any suggestions, or perhaps has seenthis before?
    Thanks,
    Doug Heerema

    Opps nevermind what I said. I misread your second paragraph. As you can't get past the post screen I have to ask if the HDD's are running like it would in a normal boot? If so then you may be set to some other scan frequency than the Monitor can handle. If so then you need to try it as Eddie suggested with a normal CRT so that you can reset to the panels native resoluition and frequency. Some Flat Panel displays don't like anything else. If that works then try to remember the last operation you did before this happened. As whatever that was likely changed the operating frequencies to somethiong the monitor did not liuke. You will need to review that before trying it again.

  • MSI NF750-G55 Hangs

    Ok, shooting in the dark here. I just purchased the MSI NF750-G55 from Newegg along with these components:
    CORSAIR Vengeance 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800), sticks in slots 1,2
    AMD Phenom II X6 1090T Black Edition Thuban 3.2GHz Socket AM3 125W Six-Core Desktop Processor (including fan)
    XFX HD-485X-ZNFC Radeon HD 4850 1GB 256-bit DDR3
    Antec NEO ECO 400C 400W Continuous Power ATX12V 2.3 / EPS12V 80 PLUS Certified Active PFC Power Supply
    The system hangs randomly. Sometimes with a BSOD (that disappears too fast to read), sometimes the screen just freezes requiring a hard reboot. Totally random, I can play Witcher II for hours just fine without and incident, or I can mess around with Solitaire and have it freeze 10 minutes in. I cannot find a pattern to it. Nothing in the Windows Event Logs other than the un-expected shutdown messages.
    I have not messed around with the BIOS settings or played around with any overclocking functions, everything is stock/default.
    I have run Memtest86, did not find nothing or hang the system. (let it run overnight)
    Windows 7 64 Professional, latest drivers from MSI and ATI (for the video card).
    Any suggestions as to where/how to start to troubleshoot this?

    Umm isn't "Vengeance" memory for use with icore/Sandybridge systems?
    I agree psu but then changed to ram issues when read the memory you're attempting to use with that system.
    I'm not seeing any Vengeance on the list for your board, XMS yea but not Vengeance unless I missed it.
    Not saying no way it can work but might require tweaking to do so.
    Have you run memtest at all?
    You really should be using the Corsair Dominator GT memory with your Phenom II see>http://www.corsair.com/vengeance-8gb-dual-channel-ddr3-memory-kit-cmz8gx3m2a1600c9.html click on the FAQs & Support link on the page.
    Might RMA exchange it with newegg or if not there talk to "Ram guy" over at Corsairs support site, he'd surly help you out if you asked I'd think.
    You might in the end get the Vengeance to work yea, if its the root cause of the issues you have now, tweaking it some to get it working right, might not be optimal to do so regardless.
    Any way I'd run memtest if you haven't, see what that tells ya first.

  • New computer MSI NF750-G55

    Hello All,
    Just received a new shipment and the computer is not passing POST, Details as follows...
    (oops) AMD Phenom II x6 1090T
    MSI NF750-G55 BIOS default no software installed yet...
    GSkill 4x4GB DDR3 1333
    CoolMax 500w +3.3 30A +12v1 18A +12v2 16A -12v 1A 12v 380W
    On Board Video
    Kingston 128gb SSD and Sony Sata DVD R/W
    Getting post to the Checking vRam and it freezes, no input after that recognized.  Computer is new, I have tried with just 1 dimm installed (yes in the correct spot) and also with only the CPU, PSU, and keyboard connected.  All fail at that point.  Post code 008F reads at that point.
    Any additional info will be given at request.

    Check the BIOS chip, as you need at least BIOS 7578v13 for that CPU.
    If the board doesn't have that version, you will need a supported CPU to flash it.
    It may also be the memory you use, try 1 el-cheapo stick and see if it posts.
    And last, if you PSU is this one:
    http://www.newegg.com/Product/Product.aspx?Item=N82E16817159062&Tpk=CoolMax%20500w
    That piece of junk will not power your system, it's old rubbish.

Maybe you are looking for