MSI P35 Neo2 (MS-7345) strange BIOS problem

Hi all,
My first post here - just wondering if someone could help me.
I recently 'accidentally' flashing my bios version from 1.8 to 1.C on my MS-7345 (P35 Neo 2) board, after deciding to install live update. While I know it's often considered a bad idea to flash the bios when everything's working, but I did it anyway. Since doing it I got many many BSODs. I'm running XP Pro 32 bit btw. I got these BSODs mostly when the computer was working hard, but not always. I'd barely be able to do anything sometimes. Occasionally Windows would even crash on start-up.
I made sure that i was running the latest drivers for all my components, peripherals, etc, including motherboard and graphics card. I even reformatted my HDD and reinstalled Windows from scratch just in case it was a virus. However, the problem has continued, and I even got a few BSODs during my reinstallation of Windows XP Pro.
Another thing I tried was reverting back to the old bios version (1.8), but this made no difference, so I eventually returned to the latest 1.C.
I've written down all the error message codes somewhere, though I've currently misplaced the sheet I wrote them on. If you need to know the exact codes I can locate it and add it to this thread. I probably got about 30 BSODs per day. Often they were IRQL_NOT_LESS_OR_EQUAL type ones, but definitely not just that. Each code I got I researched thoroughly to see if I could work out the problem. Some pointed to RAM Failure, some to HDD problems, some to bad Graphics card, some to corrupt drivers. Pretty much anything you can think of, the errors 'blamed'. However, I had a hunch regarding the bios / motherboard.
I eventually discovered (by chance) after re-flashing the bios (which I'm doing in DOS using the suggested AFUD after a reboot) that if I...
1. Switch on the computer
2. Enter BIOS Setup by pressing Del
3. Turn of the boot sector protection (in order to flash bios) and set USB stick to be the first boot device
4. Boot to DOS from my USB stick and flash the bios in DOS
5. Reboot
This is the critical bit...
6. When when I get the 'Bad checksum, Press F1 to enter BIOS setup or F2 to use default values' PRESS F2 (it won't work if you go into bios setup as this will then require another reboot before loading windows).
7. Let Windows XP load as normal.
If I follow all the above steps (I discovered this by mistake), the computer is 100% stable. I even tried some burnout tests and played some cpu & gpu intensive games with settings on full to give it a real workout, which previously would have ended up in a BSOD within seconds.
However....
If I then reboot the computer (or shut down and switch it back on the next day) and let windows load, it will be unstable again, just as before!
In other words, I'm currently having to flash the bios every time I switch on my PC or reboot it in order to get a stable system.
So this problem isn't fixed - but I've found a workaround at least for now.
Incidentally I've tried installing a new CR2032 bios battery, since I thought it might be losing settings on reboot, but this didn't make any difference.
I personally don't think it's actually the BIOS Reflashing that's making it work - just something weird in the bios settings. It's as if 'erasing the checksum' (cleaning out these dodgy bios settings), which forces the PC to load the defaults the next time it boots, is helping. I have to just mention that going into bios set-up and choosing 'Load Fail-Safe Defaults' does NOT help, since the computer reboots when you 'Save Settings and Exit'. It's as if the bios settings corrupt every time on boot, which causes the crashes.
Does anyone have any suggestions?

To return to the previous bios, just download the one you want and use the forums tool.
http://www.msi.com/product/mb/P35-Neo2-FR---FIR.html#/?div=BIOS
>>Use the MSI HQ Forum USB flasher<<
Before you do that, try to boot and enter bios. Hit f6 for optimized defaults save and exit see if the problem persists.

Similar Messages

MSI P35 Neo2-FR

Hi
MSI P35 Neo2-FR v1.1 Bios 1.1
cpu e4300
intial findings on 200 FSB jumper 9x356 takes 1.4v on NB to get into windows
9x356 on 266 FSB jumper takes stock(1.250)
Some questions, what is a safe voltage to run on the p35 chipset and on this board? Also the board defaults to 2t command rate, and I can see nowhere to select or change, where/can you change to 1t.
In Bios, there is a setting "Auto disable Dimm/PCI Frequency" what does this do?
thanks in advance

Changing the straps causes the chipset to use tighter or looser timings. Why the excessive voltage is required on 200FSB strap.
The auto disable is the PCI frequency lock, it's best enabled whenever overclocking.

Bios Update Problem P35 Neo2 - MS 7345 V 1.1

Hello
I've update my board bios because a "hard disk not present" problem and since it I was having several problems:
I'm running Windows XP SP2 and it takes a very long time to start (in bar and loading windows screen).
The major problem I have is when power on the computer it is alwayls showing the red font message that says it was a problem overclocking, so everytime I need to go into setup and to save changes whitout changing anything.
I suspect the bios I've installed is not the right one since the start screen says "MSI Neo Patinum" instead Neo2, but I've used Live Update ... so it should be the rigth one.
Can anybody help me please with this?

Quote from: Jack t.N. on 30-April-09, 06:32:24
Hi,
first of all, can you please provide full system specs for comparison? Read the >>Posting Guide<< to get an idea of what we need to know.
Hello Again, first of all I want to thank you for answering so fast. Also I have to apologize for my "not so good" english.
# CPU brand, model and speed (eg AMD Athlon64 X2 5600+ 'Brisbane' core)
DualCore Intel Pentium E2160, 1800 MHz (9 x 200)
# Motherboard model (eg K9A2 Platinum, NOT just MS-7376!!)
P35 Neo2 - MS 7345 V 1.1
http://www.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=&cat3_no=&prod_no=1261
# Memory brand, type/speed, size, number of sticks (eg 2x1GB Crucial DDR2-800)
2x1GB Supertalent DDR2-800 DDR2 SDRAM (5-5-5-15 @ 400 MHz) (4-4-4-10 @ 266 MHz) (3-3-3-8 @ 200 MHz)
# Video card brand, chipset type, memory size (eg Gainward Geforce 8800GT 512MB PCI-E)
XFX NVIDIA GeForce 8600 GT (256 MB)
# Hard drive(s) brand, size, type, speed (eg 2x Seagate 200gb SATA150)
WDC WD3200AAKS-00VYA0 (298 GB, SATAII)
# Any other peripheral cards and devices (eg MSI TV@nywhere Plus TV card, MSI PC54G2 Wireless LAN PCI card)
Multi Flash Reader USB Device
Realtek RTL8185 802.11a/b/g Wireless LAN Network Adapter   PCI
# Operating system and version (eg Microsoft Windows Vista Home Premium SP1 32bit)
MICROSOFT Windows XP Pro SP2 32bit
# Power Supply Unit brand and output in watts and DC output (amps)
Vistuba 550W Power Supply
+3.3 V   35A
+5 V     30A
+12 V   20A
Quote from: Jack t.N. on 30-April-09, 06:32:24
Three important questions:
1. Which BIOS Version were you using before the update.
2. Which Version did you update to?
3. Did you clear CMOS with main A/C power cable removed from PSU after the Update?
1. I'm not sure what bios version come with the board (my misstake) but it was older than I've now.
2. I'm actually using AMI 1.10 Build Date: 11/10/2008
3. Yes I did
Quote from: Jack t.N. on 30-April-09, 06:32:24
Did that problem disappear after the update?
The hard disk problem didn't show any more
Quote from: Jack t.N. on 30-April-09, 06:32:24
What kind of hard drive are you using and what port is it connected to?
WDC WD3200AAKS-00VYA0 (298 GB, SATAII)
it is connected to SATA 5 port acording to Board manual diagram
I've checked hard disk SMART and health and it is ok
Quote from: Jack t.N. on 30-April-09, 06:32:24
- If you have an IDE/PATA Hard Drive:
.....What kind of cable are you using? (40 or 80 wire)
.....Is there any other drive connected to the IDE cable (how are the jumper settings for each drive (MASTER/SLAVE/CABLE Select)?
I Haven't IDE/PATA Hard Drive
I will tell you the story:
I bought the computer and I was using the Blue (Marvel) sata port for the hard disk.
Then a normal day I began to have a very low Windows start so I changed the sata plug to a purple one and the problem disappeared.
Then I began to have the same problem again so I changed the plug again but problem was there anyway so decide to update bios to 1.8 version.
The problem come back randomly and sometimes it disappeared just changing the sata port to wich the plug is connected to.
After that I began to have the "No hard disk present" error and I cleared the CMOS and tried several things until it come to work again.
Few time ago I noticed that was a newer bios version, so then I used Live Update to update bios and drivers again.
Now I'm having the "slow" problem again. I'have been trying several configurations and testing programs but I just didn't find anything wrong.
Edit:
I'm having the first post problem (overcloking message after power on)
I also had a very rare issue few time ago when shutdown the pc: few minutes later it power on by It self !! until I have disabled every wake up event from setup.
I hope you can understand, and thanks again for your help.
Gabriel.

MSI P35 NEO2 FIR voltage problems!!

Let's start:
I have MSI P35 NEO2 FIR ,e5200,2 x Geil ultra plus 1066+,as us 2900CT,lcpower 6550g and...rest- not so important for my questions.
1.My problem is next: default voltage values for my RAM is ~2.2-2.4 every time I check in windows (speedfun,sisoft Sandra, everest..)shows me 2.0 or some time even 1.8v . When i change voltage in bios and went to win voltage on RAM is still unchanged (2.0v) .
Same thing happen with NB voltage. But CPU voltage I can change freely with no problem.
When I change fsb(try to overclock) suddenly memory voltage rises how i do not now , but only to 2.35 and no more.
Can anyone help me fix this problem because my memory is not stable at 2.0 or 1.8 sometimes and system crashes?
2.When i change cpu settings from 12.5*200 to (example)10*300 in windows even in system properties see that my current clock is 12.5*300=3750 and not 10*300=3000 like it should be .
Is it bios problem?
My bios version is 1.9.
Thanks!

same problem with the Neo2 FR (like mine). After quite of bit of researching and testing i reckon that software can not correctly read the vRAM on these MSI boards. I found that Speedfan, Everest, and HardwareMonitor all gave an incorrect reading for my RAM's voltage. Also, if i increased the cpu voltage in the BIOS then the voltage monitoring programs would show an increase in CPU voltage and RAM voltage (even though i had not changed the latter).

MSI P35 Neo2-FR, Im having WEIRD beeps in BIOS continiously unstopping.

Oh dear lord, i bought a new board and now im having some stupid beeps going off every 3sec in the BIOS, i updated to 1.8 bios and now its going every 1sec, BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP, every time there is a beep the system hangs a bit, i pretty much cant do anything in BIOS and its getting on my nerves. What is causing this? I tried removing all the drives, my cpu fan is connected to molex not to the motherboard though. In windows they go away, a bit when loading windows logo and it hangs the windows logo too for a few times, then all leds go green, before im getting from top to bottom Green, Green, Green, Red, Green

• Intel Core 2 Quad Q6600 2,40GHz "SLACR G0" + ASUS Silent Knight Copper
• nVidia XFX Geforce 8800GT 512MB GDDR3 + Zalman VF-1000
• MSI P35 Neo2-FR
• 4Gb 2x2Gb A-Data PC6400 800MHz DDR2
• 1Tb 2x500Gb Samsung Sata II
• Seasonic 700W M12 Modular
• Antec Sonata II
Nothing helps, tried butting a fan into the cpu fan slot, nothing, tryed removing PCI cards, nothing, NOTHING helps, it just keeps beeping and hanging on those beeps in the BIOS. When it gets to windows load screen all is fine, the frick.
EDIT: Allright, the answer to this problem is, go to windows and do a restart from windows, go to BIOS and there is no more beeping. I did a save and exit and rewent to BIOS and still no beeping, then did the shutdown and power on to BIOS and no beeps. So, weird problem but an easy answer to fix it. I think its something to do with the motherboard booting for the first time, it just needed to go to windows and make a restart. Weeeeeiiiiird.
Cya, hope this helpes someone in the future.

Msi p35 neo2-fr disable EIST in bios

hello !
My name is Adrian. My system spec.:
msi p35 neo2-fr (bios ver.1.A),
CPU core 2 duo E8400 C0
mem. dual chanel kit 2x2GB geil pristine ddr2 800
2x250 hdd western digital WD2500YS
Video Gigabyte GV-NX88T512HP 8800GT 512 DDR3
Sound Creative Sound Blaster Audigy SE
PSU Chieftec 450W 2x12v: 36 amp., 5v: 25 amp.
OS dual boot windows xp sp3 and windows vista sp2
My problem is when i disable EIST in bios Vista gives me a blue screen (0x0000007F) on boot and XP restarts without any error.
Any idea ? Thank you anticipated !

Quote from: pristine on 11-August-09, 12:31:07
I want to overclock and i want to change the multiplier to make some tests ! And i can`t do that without EIST DISABLED !
OK, stay calm. Getting frustrated is only going to make people not reply.
I'm not sure why disabling EIST is giving you a BSOD. I don't think anyone has any ideas since you have no real replies.
A kernel trap is hardware failure usually. Makes me think when you disable EIST, the machine becomes unstable. Are you setting the default multiplier for your processor? Hell, we don't even know what it is. How about you list your rig specs?
Just to add: Overclocking with EIST enabled is pretty much the same. You save power, so I don't know why you'd want to turn it off, in all honesty.

MSI P35 Neo2 Fir Patriot Memory Problems.

Hi,
Having problems with my Patriot Performance PC2-6400 Low Latency Memory DDR2 (800mhz) 4-4-4-12, 2,2v, 2 * (2gb(2*1GB)kit) =4gb total
on a MSI P35 Neo2 Fir moderboard with Intel Q6600 cpu)
When i check the memory with CPU-Zv1.44 the memory only goes with the frequencys of
DRAM Frequenzy 399.5mhz
FSb : Dram 2:3
Cas# latency 5.0 clocks
Ras# to Cas# delay 5 clocks
Ras# Precharge 5 clocks
Cycle Time 16 clocks
Why doesn't they go in 4-4-4-12 frequencys ???
Have tried to manually change dram timing in bios but no success
so i went back to auto dram timing.
What can i do to get the 4-4-4-12 timings.
Please help.
thanks in advance swefin

Quote
When i check the memory with CPU-Zv1.44 the memory only goes with the frequencys of
DRAM Frequenzy 399.5mhz
~400 MHz is the correct frequency for your modules. CPU-Z shows real clock speed. DDR means Double Data Rate (two transactions per clock cycle). Multiply 399.5 MHz by two in your head and you have your effective DDR(2) rating of 800 MHz. There is no problem here.
Quote
Why doesn't they go in 4-4-4-12 frequencys Huh
Have tried to manually change dram timing in bios but no success
so i went back to auto dram timing.
What can i do to get the 4-4-4-12 timings.
CL5 is the standard latency for DDR2-800 modules. It ensures that they are able to operate @JEDEC standard voltage settings @1.8V (+/-0.1V). The board is supposed to set memory timings to CL5, otherwise your system would not be able to boot at standard voltage. Check the "SPD" tab in CPU-Z and look for the standard timings that were programmed into the SPD chips of your modules (400 MHz), I am absolutely sure that you won't see 4-4-4-12 @400 MHz @1.8V being part of the SPD tables.
You have to manually adjust memory timings in BIOS to 4-4-4-12 AND also increase memory voltage to the value the manufacturer recommends for CL4/DDR2-800 MHz. The voltage is usually 2.0-2.2V depending on the brand and type of RAM in use.

Msi p35 neo2 fr problem

Alright, I have been using this board for quite sometime and today it gives me problem.
When i tried to boot up this morning, the board just keeps on restarting. This happened once b4 but the problem solved after I pressed on the reset button on the board.
whereas for today, after resetting, the board did stop restarting itself, but it hangs when the LED is at (red, red, green, red)from top to bottom. I refered to the user guide and it shows that there is a problem during memory detection.
Can anyone pls help?
This is what I have
Mobo: MSI P35 Neo2-FR
CPU: Intel Core 2 Duo E6750 2.66 1333mhz/4mb
RAM: Kingston Hyperx 2x2GB DDR2-800
Video Card: Nvidia Geforce 8500GT
HDD: 1xHitachi Deskstar 1TB SATA 3.0gb/s, 1 Samsung 160GB(SATA), 1 Seagate IDE 80GB(IDE)
OS: Microsoft Windows Vista Ultimate SP2
PSU: AcBell 400W DC Output (There are a few of them.. didnt know which one.. the highest is 28Amps)

Okay. About the memory issue: I believe a BIOS Update to the latest version may fix the problem with your DDR2-800 modules. BIOS v1.2, v1.3 and v1.4 had known problems with DDR2-800 modules. In case you decide to do that, please >>Use the MSI HQ Forum USB flasher<< and avoid MSI Live Update or any other Windows based flasher.
About the video card: I is not necessarely defective. Your PSU is not only a low-end poor quality device but also rather weak in the first place. Try a stronger one with your original video card and see if that changes anything.

MSI P35 Neo2 - Sleep S3 Problem

Hello.
My System:
CPU: Core2Duo E6850 @ 3.0 Ghz (FSB:1333 | 333 x 4)
RAM: 4 x Kingstone HyperX DDR2 1Gb ram @ 800mhz
M/B: MSI P35 Neo2 Fir
GPU: Gigabyte Radeon HD5770 1024mb
HDD: Western Digital BlackCaviar 640gb 64mb cache
SSD: OCZ Agility 3 60gb
PSU: Fortron BLUESTORM 400w
O.S: Windows 7 (SP1/Without SP) Ultimate / Hackintosh 10.5.8 / 10.6.8 / 10.7.3 / OpenSuse 11.2 / 12.1
Recently i decided to enable the sleep mode on my computer (because the power cost, my computer is all the time on).
So, i go to my bios and i change the suspend mode to S3. I boot my os (windows7) and i tried to sleep.
The system is going to sleep fine but nevers wakeup, the led of motherboard is flashing fast red-green-reg-green and after random time stops flashing, sometimes all are red and sometimes are all green!
Before post here i tried to fix the sleep and i read evert post.
I have try: Flash Bios to (1.8, 1.7, 1.2, 1.C, 1.A, 1.9), update all of my drivers including (lan, gpu, chipset), disconnect every usb includes keyboard (i tried with old ps2 keyboard), disconnect all pci cards, disconnect all RAM's (except one), i tried another Graphics Card (Gigabyte 8600GT), another PSU (Premier 400w), Bios Settings (ACHI/IDE, Recall GPU, PCI express x4, clear cmos), change DVI connector port on gpu, change to analogue RGB D-SUB, reinstall windows to ide disk/sata disk with S3 Enabled!
I tried to sleep from my Hackintosh 10.7 with the same error and with linux (openSuse) with the same error.
I have notice coz when i remove rams and i downclock the cpu and rams the leds are stop flashing in 2-3 secs (normaly tooks 10-40 secs)
Also the mb never wake with keyboard key press event!
Please experts, i need your help...

@NovJoe
Thanks for reply!
I have test with one piece of ram. also i tested with another cpu (Intel Celeron 1.6 - i cant remember the model).
My motherboard version is 1.2 (MS-7345 V1.2)
(i dont know if it helps but hibernation working really good! working on windows and mac)
before a hour i test to reprogram bios with floppy disk! first i destroy my bios (i edited with ami tools to corrupt and the mobo start the recovery process, i put a floppy with the last bios renamed to AMIBOOT.ROM and the recovery worked! but sleep not)
i dont want to talk with msi for a too old mobo, so if anyone knows whats is happen please help.

Need Help with ESATA on MSI P35 Neo2-FR

I have the MSI P35 Neo2-FR motherboard http://www.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=&cat3_no=&prod_no=1261 and trying to get the eternal ESATA to work. It works with one individual HD. I'm using an external ESATA drive with 3 HD inside the external case with one cable running into the external ESATA in the back of the motherboard. It's only recognizing 1 drive and the other 2 isn't showing up. If I switch it to USB connection it will read all 3 drives. I'm running windows 7 x64 but it recognize on my other 2 computers with a different motherboard. I have install it with the ACHI setup in Bios and I've also install the Matrix Storage Controller after installation. I never install the Intel ICH9R SATA RAID driver where you have to press the F6 to install it. Is that what I'm missing and is taht needed for the ESATA to work? I'm getting this message "A storage device was connected. If this device is a port multiplier, only port 0 of the port multiplier will be active." Been googling all day and still can't figure out what I'm missing.
Any help would greatly be appreciated.

Quote
For some reason this board is Bios only have IDE, RAID and ACHI and I don't see a SATA.
IDE, RAID and AHCI are operating modes of the SATA Controller. Everything okay here.
Quote
Seems to me it's either this board and it's driver don't let you use the port multiplier but it suppose to support port multiplier.
It is neither the board, nor is it the driver. It is a limitation of the Intel ICH9R Chipset. You will have the same problem on all P35/ICH9R based mainboards. Read here:
http://xtreview.com/addcomment-id-788-view-intel-technology-matrix-RAID-and-port--multiplier.html
Quote
Unfortunately, used in the south bridges ICH9R the version of such technology provides access only to one hard disk at the specific moment of time. . The technology became more complex to realize , which implies to several access disks simultaneously, possesses higher cost and more higher central processor loads , therefore it can be rejected.
Here is the same problem on a Gigabyte GA-P35-DQ6:
http://forums.overclockers.co.uk/showthread.php?p=11892094
Nothing you can do about it.

Msi p35 neo2 fr motherboard - system freezes

Hello , I just bought a Msi p35 neo2 fr motherboard and I have this problem . My system randomly freezes ,no errors ,no blue
screens and I have to restart it . I tried each module of ram separately and I got the same problem .
The video card worked fine on my old system and I don`t think this could be . Also the standby led (led 3 ) is always on and red
Maybe I messed up the " wire up " . I could use some tips about how to properly wire up and which settings should be done in BIos for my configuration ?
Msi p35 neo2 fr
PSU Sirtec HPC-430-P12S V2.2
2x1 gb Geil pc6400 800 mhz
video geforce 6200 128 mb
hdd sata 120 gb

from the User Manual:
Quote
Spread Spectrum
When the motherboard’s clock generator pulses, the extreme values (spikes) of the
pulses creates EMI (Electromagnetic Interference). The Spread Spectrum function
reduces the EMI generated by modulating the pulses so that the spikes of the pulses
are reduced to flatter curves. If you do not have any EMI problem, leave the setting at
[Disabled] for optimal system stability and performance. But if you are plagued by EMI,
select the desired range for EMI reduction. Remember to disable Spread Spectrum
function if you are overclocking, because even a slight jitter can introduce a temporary
boost in clock speed which may just cause your overclocked processor to lock
up."

MSI P35 Neo2-Fr -- can't get onboard audio device to appear in XP

I've just installed XP sp3 onto my new mobo (MSI P35 Neo2-Fr).
Attached is Q6600 core2 quad processor, 2GB memory (DDR2), ATI HD4850 gfx card. I haven't changed the bios much at all or overclocked anything yet.
All seems fine *except* that I can't windows XP to see that there's an onboard audio device.
(It is enabled in the bios btw.) I've tried installing the high def audio driver on the CD from mobo box, and also downloaded the latest from the MSI site. I uninstall the driver and reboot before trying to reinstall it again btw.
The audio driver installer used to say there was a problem installing the driver, but it doesn't any more. After installing it and rebooting, XP control panel -> Audio devices says there are no audio devices.
Also, I notice that there should be an extra audio item in the XP control panel (according to mobo manual), but this hasn't appeared.
In XP's system hardware list there are no sound devices under Sound, but there are two unknown PCI devices (with yellow question marks next to them).
Any suggestions?

Quote from: Del UK on 05-September-08, 05:13:05
Had same issue with ATI card installed.
Go to Microsoft update and choose custom
You should see a list with hardware updates..........
After that, all will be fine
Hi there
Thanks for your reply. I went to MS updates, didn't see any in custom about hardware (apart from updated ethernet driver). Installed all updates anyway. And the problem remains...

MSI P35 Neo2-FR booting error

Hello all.
The problem I'm having is concerning a MSI P35 Neo2-FR. For about the past year, this mainboard has been used in a Windows Home Server Setup. Not to long ago, we had a power outage (Yes, should have been plugged up to a UPS, Mea Culpa). When the power came back, (and I got home), it couldn't get it to boot. It was doing the old MSI False boot routine that has become infamous. While checking the cables inside, I hit the CMOS reset button while the power was on. Now, I'm not sure how completely screwed I am, but at this point I'm stalled as far as booting at the "initializing keyboard" status light indicator. (Two red followed by a green, then another red, from top to bottom on the LED status light strip). It just hangs there forever. I can't get to a bios screen.
Is there anyway to salvage this?
Oh, and I have an Identical system (different videocard, but same MB, Ram and CPU that went through it, to no ill effects.)
Before it's asked, I have fiddled with the memory (swapped slots, used one stick etc), I have tried booting it with no RAM, no Keyboard, a PS2 Keyboard and a USB Keyboard. All to no avail.

hoho resetting the BIOS while the system is still on is a big sin..I have done the same mistake as u are and to settle this..there's a thing called RMA,u might want to try that

MSI P35 Neo2-FR Won't Boot From CD

Just received my new board which aside from the problem, is fantastic! It's an MSI P35 Neo2-FR
I've got DVD drive to first in the boot sequence and it prompts me to press any key to boot from CD however when I press any key it just hangs on press any key. Got some advice from a friend and he told me to load optimized defaults however it doesn't make a difference.
Help?

Quote from: Sharp on 24-February-08, 00:09:47
Hello,
Could be a few things.
Make a list of everything that you are using with the board so that we know what you have.
EG, look at the bottom of my post.
Do you have a floppy drive?
http://www.memtest.org/download/2.01/memtest86+-2.01.floppy.zip
- Extract all the files to a folder.
- Run the install file and it will create a memtest boot disk for you.
- Then boot from the floppy disk and let the program run for a while (4 hours+)
- If it detects any errors instantly stop and report back here. (or try 1 stick at a time)
CD or USB versions available here.
http://www.memtest.org/#downiso
But it is important that we know what else you are using with the board.
Could be a weak power supply or you are using different branded memory modules.
And did you plug all the power connectors into the board?
- 24pin ATX
- 8pin +12v EPS connector
- Molex near the first PCIE x16 slot.
Just incase this thought has crossed your mind,
Do not attempt to the flash the BIOS until you know the system is 100% stable/working
Molex near PCI-E X16 slot? I didn't plug that in no. What's it for may I ask?

MSI P35 Neo2-FR/FIR wont overclock

This might be a simple question but here it is. My new MSI p35 bios v 1.34 wont allow me to overclock my q66oo. I think the problem is windows xp pro 64. I cant install the MSI dual core center or the live monitor. When I am in the bios I canot change these setting inside the cell menu,
cpu fsb frequency
adjust cpu ratio
cpu voltage
memory voltage
vtt fsb voltage
nb voltage
sb i/o power
sb core power
Any ideas?
MSI P35 Neo2-Fr
intel q6600
evea 8800 gt
g. skill 1 gig pc2 6400 2 sticks
corsair hx620w

Keep us updated on your progress.

MSI P35 Neo2 (MS-7345) strange BIOS problem

Similar Messages

Maybe you are looking for