MSI P45 Neo (question about new bios v1.9)

Hi!
2009-04-03 MSI releasen new BIOS v1.9 to MSI P45 Neo
Fixed: - Disabled 5V USB function under S4/S5.
Tell me plz - what that mean ? It's very recommended update or not?
Many thanks!

If you have no problems with the BIOS Version you are currently using, there is no need to update the BIOS (and it is not recommended to do that either).
Quote
Tell me plz - what that mean ?
S4 - State = Hibernation
S5 - State = Shutdown-State
The BIOS Update should turn off the 5V power supply to the USB Ports when the system is shutdown (S5) or in Hibernation State (S4).

Similar Messages

MSI P45 Diamond : Question about voltages and straps.

Hi,
Before I start a post with my overclocking problems I want to learn more about the board and have a few questions:
1. OC Jumpers: What do they exactly do, do the increase any voltages, do the change the nb strap or do they only increase the fsb. If they do not change the strap, when/where does the board change it 266/333/400?
2. What is the maximum safe voltages for the mch,ich,fsb?
3. New BIOS: Does anyone know when can we expect one or where can I download a beta that is newer than 1.4.
Ok, my problem is that I can overclock past 390. I can get 400 but it is not stable in windows. I first want tolearn how the board works before I discuss my oc problem.
PC Specs:
MSI P45 Diamond (v1.4 Bios)
Intel Q9300 (ran 2000fsb on a xfx 780i)
4x1gb Transcend aXeram DDR3-1800+
Zalman 850W power supply
XFX GTX 260 XXX
Xfi Titanium
Thanks

Quote
1. OC Jumpers: What do they exactly do, do the increase any voltages, do the change the nb strap or do they only increase the fsb. If they do not change the strap, when/where does the board change it 266/333/400?
The jumpers change the strap & the FSB Frequency:
When you have an FSB-266 MHz processor and put the jumpers into the 333 MHz position, the FSB Clock Speed will be forced to 333 MHz and the BIOS treats the CPU as though it is an FSB-333-MHz Processor, that means even after a CMOS Clear, the FSB Clock Speed will be 333 MHz and FSB/Memory Ratio will be adjusted automatically based on that strap and the SPD Tables of your memory modules.
Quote
2. What is the maximum safe voltages for the mch,ich,fsb?
The Intel Datasheet for the P45 Chipset should give you a basic overview on voltage ranges. However, you may need to exceed these ranges, in some cases, depending on your overclock to keep the system stable. You will find nobody, that will seriously be willing to tell you the "maximum safe voltage" as every voltage increase is potentially dangerous to your the components. Welcome to overclocking.
Quote
3. New BIOS: Does anyone know when can we expect one or where can I download a beta that is newer than 1.4.
The latest BETA I know about so far is v1.5b1.
Quote
Ok, my problem is that I can overclock past 390. I can get 400 but it is not stable in windows. I first want tolearn how the board works before I discuss my oc problem.
Please give a full overview of your Cell Menu settings if you need suggestions.

Question about new BIOS on Satellite L20-182

Hi :)
I've got one question: may I install new BIOS 2.20 on my Satellite L20-182 model no. PSL2XE?
If I can't, why users PSL2X can do this? Are there so many differences on both models?
Greetings and sorry for my English - I'n not the best :)

Hi,
just for explanation: the bios you mentioned is the right bios for the machine. Toshiba is not writing the full model number since there is a range of model numbers of the same model, so dont worry, they are not different. Maybe the last digit but this is not important for you.
Why I am knowing this? Because many manufacturers are doing this and I was many times confused when updating bioses from another manufacturer...
Greets

Qosmio X500-11U- Question about new BIOS update

Hi to everyone
I need to clarify a matter, the BIOS update that was released December 2010 was the 2.90 now a new release march 2011 is named 1.40! Is this an upgrade a downgrade or a joke? Should I proceed with the newest 1.40 or stick with the old 2.90?
I forgot to mention that I own a X500-11U and thanks in advance

Hi nick73,
On Toshiba European driver download page there are two different versions available:
BIOS-Update 1.40-WIN for X500 PQX34E models
BIOS-Update 2.90-WIN for X500 PQX33E models
Your model the X500-11U belongs to PQX33E series and that means only BIOS Update 2.90 is compatible and 1.40 would be the wrong version.
So its not a joke and before you search for BIOS update next time, also use the correct part number ;)

MSI P45 NEO-F Overclock different from BIOS 1.1 and 1.7

Hi,
I have the follow configuration:
Case: CoolerMaster Centurion 590
Mobo: MSI P45 NEO-F
PS: Corsair TX650W
MEM: 2GB OCZ Platinum 800Mhz 4-4-4-12
GPU: eVGA 9800 GTX
CPU: Q6600 G0 with stock cooler
OS: Windows Vista 32bit
DualCore Center
eVGA Precision 1.5.1
I was using BIOS 1.1 and OC the CPU to 3.0 GHz using FSB 333, vcore AUTO, DRAM 1.9v, DRAM Mult 1:1.25 (833Mhz), EIST Enable and all other settings default.
Everything is OK, but I was unable to rise the CPU to 3.6Ghz using FSB 450. (The maximum that I get is 3.2Ghz with FSB 400 and DRAM Mult 1:1 (800Mhz) )
Now, i have updated my bios to the latest version 1.7.
The first difference is then i leave the FSB with 333, my DualCore Center shows 331 (2.979Ghz ) and CPU-Z shows FSB 332. This won´t happens when the BIOS was 1.1 and DualCore Center shows FSB 333 and CPU-Z too. (Seems that BIOS 1.1 has a better precision with FSB frequencies than 1.7)
Now, i can configure the CPU to 3.6Ghz (Using FSB 450), the system boot up but restart when loading the startup programs in windows.
My question is why with new bios 1.7 my fsb shows different from BIOS and DualCore Center/CPU-Z.
What information is correct? The BIOS or the DualCore Center/CPU-Z?
Has anyone already configured Q6600 to 3.6Ghz FSB 450 with P45 NEO-F and BIOS 1.1 or 1.7?

Quote from: koike on 21-March-09, 23:14:40
Thanks Vern,
I´m thinking in get a Zalman 9700 cooler.
Now I have started to do what you say and increase the fsb by steps of 5 and run 3dmak06 and Everest stress test for 5 or 10 minutes to see if the system is stable.
Now i´m running fsb 340x9 with vCore 1.33 and DRAM 840Mhz with volt 1.9. Everything is ok.
I have upgraded the BIOS to 1.8, but the problem of difference from bios setup and cpu-z fsb reading are still there. (The Bios is 340 but CPU-Z and DualCore Center is 337) Do you have the same problem?
Little at a time is the way to go. When you get that cooler you can get your vcore up in the 1.4 range. Then you should get higher numbers. You will nearly always see a different cpu speed in windows than what you see in bios. That's not a problem.

MSI P45 Neo Power Led question

Hi !
I am building my first computer and I have a problem.
I have a computer case called Antec 300 and a motherboard MSI P45 Neo and I have a question for connecting the Power Led cabel, the cabel in my computer case have 3 holes in it and the cabels are in hole no. 1 and 3,and in the motherboard manual the connectors is named JFP1 and JFP2. I have installed the power/reset switches and the HDD Led to JFP1,but the Power Led don´t fit in to JFP1 as one cabel will stick outside from JFP1, so my question is, can I put the Power Led to JFP2 as it belongs to the front panel connectors and as it also says Power Led and speaker.
Can I use JFP2 to install the Power Led instead of JFP1 ?
Or how do I solve this?
Here is a link where the manual can be downloaded http://global.msi.com.tw/index.php?func=downloadfile&dno=6792&type=manual
I hope someone can help me with this.

Quote
Can I use JFP2 to install the Power Led instead of JFP1 ?
Yes, that is where it is supposed to be connected to. The pin definition for JFP2 in the manual explicitly says "Power LED".

Overclock E8400 + MSI P45 NEO Final results

This is the final result, and the default config for me from now on, thank you Jack the Newbe, you helped me a lot.
I fixed your links and tags
-Frankenputer

HARDWARE
MOBO: MSI P45 NEO - BIOS Version 1.1
CPU: C2D E8400 3.0Ghz - Cooler Box
MEM: 2x 2Gb DDR2 800Mhz Kingston Value Ram
GPU: MSI GeForce N9800GTX 512Mb(700/2200/1750)
HDD: Seagate 250Gb Sata II
PSU: Akasa 500W
CASE: Cooler Master Elite 333
Monitor: 19" Samsung 943BWX Wide (1440x900)
OS: Win Vista Ultimate x64 + SP1
CLOCKS AND VOLTAGES
CPU - BIOS
Multi-Step OC - [MODE 1]
D.O.T Control - [Disabled]
Intel EIST - [Disabled]
Adjust CPU FSB Frequency (Mhz) - [445]
Adjusted CPU Frequency (Mhz) - [4000]
Multiplier - [9]
Advance DRAM Configuration -
Timings - [5-5-5-15]
FSB DRAM Ratio - [1:1.00]
Adjusted DRAM Frequency (Mhz) [890]
ClockGen Tuner - [Untouched]
Adjust PCI Frequency (Mhz) - [Default]
Auto Disable DRAM/PCI Frequency - [Enabled]
CPU Voltage (v) - [1.3350]
DRAM Voltage (v) - [1.90]
MCH Voltage (v) - [1.100]
VTT FSB Voltage(v)- [1.25]
ICH Voltage (V) - [1.50]
Spread Spectrum - [Disabled]
GPU - Riva Tuner 2.10
Core Clock (Mhz) - [783]
Shader Clock (Mhz) - [1957]
Memory Clock (Mhz) - [1183]
FAN Speed (RPM) - [95%]
TEMPERATURES
Ambient Temp - 30~31ºC
CPU
Idle - 56~60ºC
Full Load - 85~90ºC
GPU
Idle - 45ºC
Full Load - 60ºC
I know that these CPU temps are not aceptable, but as soon as my thermal grease arrives I'll use it with my TT cooler(current I'm on cooler box) and it will drop a lot.
COOLING
I just use:
a 120mm fan in the lower front of the case sucking the (cool)air in,
a 120mm fan in the middle back of the case blowing the (hot)air out,
a 80mm fan fixed in the door case blowing the (hot) air out,
a 80mm fan over the back of the VGA blowing air to the Northbridge heatsink,
and (about next week) Thermaltake Big Thyphoon 120 VX with Artic Silver 5.
The MSI N9800GTX is the best VGA cooler that I ever saw, it really does the job even in the extreme overclocks.
FINAL WORDS
After I did this OC, I used the machine for about 4 hours with no problem at all. I did some tests, including some benchmarks like Super PI and 3Dmark 2006, but I did not made any stress test(prime95, orthos) because I'm still using the cooler box and this will for sure overheat it beyond it's capacity, therefore this OC was just a preparation(test) for the real one that I'll do when my thermal grease and my TT cooler were in place, I think that the voltages still can suffer some variation with the advantage of the new cooler, but it will be worked in the right moment, after all overclocking is a long process, when I wrote "final results" to the title of this topic, I mean that this is the clock that I wanted to reach, but of course that still lacks some fine adjustments.
The real objective of this test was to see:
1. if the motherboard handles it stable.
2. if there were no FSB walls to block my OC.
3. if there were any voltage problems.
4. if there were extreme overheating.(even with the cooler box)
and I'm more than happy to see that it passed in all the tests so far.
PROGRAMS USED FOR ADJUSTING AND MONITORING
CPU-Z v1.47
GPU-Z v0.27
Core Temp v0.99.3
Riva Tuner 2.10
Super PI v1.5
3DMark06 v110

MSI P45 Neo-f with intermittent boot problems

Current system:
*CPU: Intel core2duo 4300 1,80GHz
Mobo: MSI P45 Neo-F LGA775
*Memory: 1 Kingston 1GB PC2-5300 667MHz DDR2 and 1 Dane-Elec 1GB PC2-5300 667MHz DDR2
Videocard: Club3D Nvidia 8800GT 512MB GDDR3
*Hard drive: 120GB IBM deskstar 7200rpm Ultra-ATA/100 (yes I realize it is known as the deathstar, but it hasn't failed so far, I do back-up because I'm paranoid
PSU: Real Silent Nexus NX-5000 500 watt
*Soundcard: Soundblaster Audigy
OS: Windows XP home, service pack 2
*Lite-on IT dvd-rom drive
*floppy disk drive
I also have 3 case fans spinning away in a marginally large Chieftec Dragon tower.
The parts I marked with an asterisk (*) are parts that I removed from my old rig and re-used.
I'll try to give a clear rundown of my problem and the steps I've taken so far.
3 days ago I acquired the P45 Neo and installed it into my system, together with the 8800GT videocard. I was still using my old PSU, a Chieftec 360watt. This PSU served me well for 7 years, but it was starting to build up noise while trying to keep up games on my old rig.
I had some trouble getting the system to boot, I tried changing some of the 4 pins wires going to the hard drive and the dvd drive. I don't know if it was luck or if I managed to divide the load properly for the system to boot. But I succeeded into booting up, got into the bios and eventually installed WinXP.
As soon as it was time to install the videocard drivers, it stopped responding. I assumed it was a power issue, since I could only install the 20pin and 4pin cpu, but my Chieftec PSU didn't have a 24pin plug to the mobo - and it needed replacing anyway! So I bought a new 500watt PSU that had all the required plugs and more wattage.
I installed the new PSU, checked every connection and pressed the power button. 'Lo and behold, the computer starts up. I install the videocard drivers and it proceeds with no problems. I try to install the soundcard, but the cd says I don't have one installed. I fix that by going to the System list and install the drivers from there. I install a firewall. By then I have successfully rebooted the computer 3 or 4 times. I decide all is well and turn off the computer. But I realize I wanted to check up something on the internet.
I press the powerbutton. The PC power light go up for just a fraction of a second. I can see the blue LED of one of the case fans switching on just as briefly - then it goes out. The computer keeps trying to turn itself on. It looks like it's hickupping to try and boot!
I turn off the PSU power on the back-side because the computer keeps trying and wait for a bit. After 10 minutes, it still doesn't work. I leave the computer for a bit and return an hour later. The computer then starts up with no problems. I turn it off after a few hours, do a reset, start it up, no problems. But then the next day it happens again.
It's pretty tough figuring out what the problem is because it looks..almost random. I considered it could be a heat issue, but sometimes it *does* start up just after it's been turned down. Checking the bios shows no strange temperature shifts.
Hope anyone can help me, because I do not want to go back to my old Asrock mobo

While powered down I cleared the cmos data, removed the Dane Elec DDR2 module and set the bios to optimized defaults. Computer restarted to WinXP with no problems (it has been off the whole night). I shut down WinXP, wait a few moments and then turn the computer back on. Alas, it won't start and starts hick-upping. I turn power off at the PSU again, so it stops.
Now I try switching out the Kingston module instead. By now the computer has been off for 10 min (while I write this entry on laptop). I press the power button on the PSU and then the power button on the front. There is a short pause, lasting a second. The computer turns on, longer now, but it only lasts 2 whole seconds before it turns off again and goes on again (I believe now you can call it powercycling). It repeats this process until I shut off the PSU.
I check to see if I have installed it properly and try again but it starts powercycling again.
15 min pass, I put the Kingston module back in, press the power button and voila, this time it does start. WinXP shows up, no problems. I leave it on for a bit and then shut down. And when I press the power button again - the feeling of dread returns, when it starts hickupping again.
I'm going to see if I can install one of the memory modules from my housemate. Then hopefully tommorrow, I'm going to try if I can test a different PSU, since I see someone else on the forum - who recently posted, has the exact same power supply and also has boot problems, coincidence... or not ^^;.

E8500 + MSI P45 Neo

Hello! I'm trying to OC my E8500 and I've ran to some issues with this combo.
I've ran it somewhere @ 3,6GHz for couple of years now with auto CPU voltage. Now I decided to buy a decent cooler because new CPU coming and decided that I should try going over it.
I tried to bumb the CPU voltage but no effect, I added little bit to everything, No effect. It seems that the max FSB for me is 386x9.5 which gives me the clock of 3667MHz and I'm unable to go over it. Still this CPU should OC well and I got confirmation that this MOBO should be able to do more from here : https://forum-en.msi.com/index.php?topic=119816.0
I tried those settings with my system and boom overclocking failed ofcourse. The thing is what I've been noticing is that the Dram frequency gets set to 1068MHz somehow and I've set it to 890MHz what is causing this?
Specs:
E8500 3,16GHz (~3,6GHz with auto voltage)
MSI P45 NEO (bios 1.C)
A-Data 4GB 800MHz DDR2
ASUS 560TI DCII TOP
I've been trying to solve this problem @ overclockers.com but nothing url to the thread : http://www.overclockers.com/forums/showthread.php?t=688445

Up your DRAM voltage to ~1,95V.
Set your Multi step OC booster to mode 2. It helped me on my P45 Platinum.
Have you removed the FSB jumpers on your board to set a 400FSB on boot ? If not, reset your BIOS to defaults first, and then try that. It worked well on my board, but you will need to check with your board.
These settings helped me achieve a stable 24/7 on my board with a Q9550 with a 450FSB.
DRAM ratio 1:1
CPU V 1.3325
DRAM V 1.956
MCH V 1.352
VTT FSB V 1.35
You may have to reduce your multi to around 7 for a start and see if you can get it stable with a 440-450FSB. Then start increasing your multi.

MSI P45 Neo-f System

Hello there MSI info seekers. This is my first time posting here, but I've used this forum as a guide to build a system online. I've been told by several sources that this motherboard cannot put out the numbers that I desire without risking burning up the whole setup. Now, im no dummy when it comes to overclocking, but I wouldnt say that I know enough to push where I'd like. I recently purchased a system with;
Mobo: MSI P45 Neo-f (possibly replacing if it cannot perform a 4.25 GHZ overclock and support 8 gigs of memory)
Proc: Intel E8500 Core 2 Duo
Memory: 4GB <random> - to be replaced by 4/8GB of Corsair Dominator 1066mhz 5-5-5-15 2.1v (clocked down due to this boards displayed fussiness with stuff over 800mhz)
Video: <generic Nvidia 9500 1gb mem> - to be replaced by an EVGA Nvidia GTX 260 (revision 2, overclocked edition)
Storage: 300GB Velociraptor (for gaming) & 500GB <random brand> storage drives
I have a 750 watt power supply, 2 LG cd/dvd burners, and ... I think that should be it.
My question is, does anyone here have experience with this motherboard enough to give me any suggestions on overclocking this rig (or pointing me in the direction of a more reliable motherboard for the application/abuse I want to put it through - even if its to a DFI lanparty or some such)? I've seen some horror stories with it not being very reliable and want this rig to be stable and reliable for a few years, even if I have to remove the motherboard and slap in a new one myself. I'd be happy with a 4.0 GHz overclock, but eventually would want more.
Any insightful posts would be appreciated, thank you ahead of time

Ah yes wouldnt it be nice to be sure it will do 4.25GHz.
Let me check my crystal ball
But alas, you get no garantuee, with any manufacturer, that it will reach your desired speeds.
First of there's the cpu, you and I cant tell if its a crappy one, or a good one.
So thats limiting factor numero uno, if your cpu will "only" get to, for instance, 3.6GHz.
Remember its rated at 3.16GHz so in Intels eyes its still a good cpu, but you'll probably think of it as crap, since your friend, neighbours or whom ever, got an E8500 to 4+GHz.
Its not something I would complain abouth though, cause 4.25Ghz is nice, but the few fps more I get for running my cpu at its limit, isnt worth it for me.
And yes thats all you gain when raising cpu speed, a few fps.
Second, 8GB 1066MHz, without the use of an AMD or Bloomfield intel (core i7), you wont ever be able to run it at 1066MHz ( And those cpu's dont fit this board ).
On Core2 boards, no matter what people tell you, it aint gonna happen, 4x2GB 1066MHz.
With all 4 slots occupied, your limited to 800MHz, if you get lucky somewhere in the 900's.
This is something that involves all manufacturers, because of memorycontroller, not being able to cope with all the data from "double" dualchannel.
And why use 8GB??? Apparently you'll use it mainly for gaming, 4GB is enough, more then, these days.
If you decode/recode, rar a lot, I would consider a quad with 8GB of fast 800MHz memory.
If you use it only for watching movies, gaming, homeoffice and inet, a good dualcore, like the one you're on planning to get and 4GB 1066MHz will do.
On 4GB, 2x2GB, not 4x1GB, you can also do 1066MHz with your mem, cause then your not limited.
The board, well Ive seen many peeps doin 4GHz + speeds on it without any issues, here in Holland they reached a massive 5.6GHz OC during a competitionwith liquid nitrogen and the board still worked flawlessly, so that shouldnt be a problem.
Apart from the above, i would say nice setup.
I'll take it any day

Q6600 OC Voltage with MSI P45 Neo-F

Hi Guys,
This is my first post, so bear with me a little!
First, my system:
Intel Q6600 G0
MSI P45 Neo-F mobo with 1.9 BIOS (factory installed)
Thermaltake Soprano case
8GB Kingston HyperX T1 1066 DDR2 (@ 800)
Changed the 120mm case fans for Thermaltake ISGC 12's
Changed the Stock Cooler for a CoolerMaster Hyper TX3 with an additional BladeMaster 92 fan in a push/pull config.
Used MX3 thermal paste.
Everything is running fine at stock settings.
I would like to get a bit more juice out of the CPU if I can - The PC is mostly used for work and general internet/mail, but I do game on it and I would like to get as much out of it as I can.
I've done quite a bit reading, and looked at a lot of other posts/forums, but I just can't replicate what others are doing with similar setups.
My problem is this:
I can get the chip stable at 3200 in Prime95, but only if I ramp the core v up to 1.4850. Most people with the same setup and similar cooling seem to be able to achieve this at a much lower voltage - usually around 1.37v or so.
Can anyone point me to where to start looking for the problem here?
I haven't done a lot of overclocking before and I'd appreciate some advice.
Thanks,
SeraphTC

Quote from: Jack on 19-January-11, 21:23:16
Set the board's OC jumpers into the 266->333 MHz position and clear CMOS after that. See if the system boots and if it does, try overclocking it from the 333 MHz strap.
I did as you suggested - booting at 266->333 is actually completely stable. The system boots at 3Ghz and seems fine with no adjustments. Once I tried to OC though it looks like the same old story - the system isn't stable until we hit 1.4850.
I didn't think it was possible to obtain stable OC by simply increasing the VCore any longer...everything I've read says I should have to play around with other settings....but this system is proving me wrong!!
The problem is, it's not getting stable fast enough for my liking.
I'm happy it's stable with my OC settings - 360x9 FSB, 3.2Ghz, VCore at 1.4850v, RAM at 4-4-4-12 at 864 with 2.1v (The RAM is rated at 2.2v), but I don't like having to feed it so many V's really.
Any other ideas?

MSI P45 NEO 3 reports incorect memory settings

I have the following system:
MSI P45 NEO 3 FR (PCB 1.0), Intel E8400, 2x1GB DDR2 A-DATA EXTREME 800+(4-4-4-12), Palyt 8800GS, Samsung 640 GBx2, DVD-RW, FDD, Sirtec 460W.
BIOS (MEMORY-Z) and CPU-Z reports that my memories are 5-5-5-18. I've manually set the latency to 4-4-4-12 and the voltage to 2,004V but the problem remains. I've updated my bios to the latest release, but the same.
What can i do to set the correct values?

Memory-Z reads the SPD-Profiles of your memory modules. Nothing you set in BIOS will ever change the information that Memory-Z shows. The actual timings that are currently used can be checked via the CPU-Z "Memory" Tab or tools like Memset.
Quote
Another problem that i observed is when i set the SATA to AHCI mode my computer POST very slowly (around 5 minutes)
Is the Power on Self Test slow or the booting phase of the operating system (which operating system do you use)?
What is your current BIOS Version?

MSI P45 NEO- F

Hello
I am using a MSI P45 neo- f motherboard.
my hard drive failed (Western Digital 400gb sata) and i just purchase a seagate barracuda 1tb sata 32 mb cache 7200 rpm data 3gb's data rate
does anyone know if this motherboard can support this hard drive
I am not a techy person, but have taught myself to build computers thru a magazine article. I have been using this home build for 3 years and have not had any issues with it. When I do encounter issues i search the boards for answers..
thanks

yes it should be supported!
i have an older board then that running a 1.5TB drive so i wouldn't think that you would have any compatability problems!

MSI P45 Neo-F: Computer having problem starting up, and crushes frequently

Hello,
I have the following rig:
Pentium Dual Core E5200
MSI P45 Neo-F
2x2GB Kingston DDR2 RAM
Seasonic 500W SS-500ET
The problem is that when i start the comp, i won't start up (the computer gets power, and the fans\hd are spinning, but nothing show up and no beeps).
I have to do several resets and wait for a few minutes in order for it to start. I get a few bsods, resets, and finally, the windows is up.
When I work in windows, I get freezes and BSODs from time to time.
I tried to:
-disconnect all drives
-disconnect all USB peripherals
-disconnect TV tuner and Sound Card
-disconnect every other memory slot, one for each time
-ran Memtest86 - the memory came out fine
-ran Intel burn test - which failed
-ran furmark - passed ok.
-changed the PSU.
-the CPU's temratures are fine (around ~35 c)
I think the problem is in the MB, as this behavior is not common for CPU failure. The comp crushed randomly, not when it is loaded.
Can somebody comfirm it?
What can I do?
Thank you in advance!!

Quote
2x2GB Kingston DDR2 RAM
What is the exact Kingston Model Number of those modules?

Msi p45 neo f audio drivers

Where can i find the msi p45 neo f MS-7519 realtek audio drivers?
i get a popping sound whenever i pause videos from my 4850 video card connected to a receiver using a dvi to hdmi. i wonder if i update my realtek drivers will it get rid of the annoying popping?

Here's the Realtek drivers if you wish to give them a try: http://downloads.guru3d.com/Realtek-HD-Audio-2.60-audio-driver-download-2717.html

MSI P45 Neo (question about new bios v1.9)

Similar Messages

Maybe you are looking for