MSI P45 Platinum and Scythe Ninja 2

Hi all,
I'm a rookie here and sorry if this question has already been asked but search didn't give solution. I'm planning to buy an MSI P45 Platinum and found Circu-Pipe 2 interesting. They said it leaves enough space for "giant CPU heatsinks". Scythe's Ninja 2 seems to be a giant one... Cause I will purchase them via net, I cannot try them manually in a shop. Does anyone (or friend...) have the same or similar Circu-Pipe-d mainboard with a Ninja 2? Will them work together?
Thanks in advance!
Cheers!

Managed to find the following link after doing a search, hope it answer ur queries
http://www.scythe-eu.com/forum/mainboard-compatibility/498-msi-p45-platinum-compatability.html

Similar Messages

  • MSI P45 Platinum and RAID 0!

    System specs below! First of all this system is basically a gaming rig. I am running Vista 64 on one single Western digital hard drive, and using an identical drive for storage. I was thinking about setting up a RAID 0 array with these two drives. Can this be easily done with this mobo? I am just wondering if there are any quirks associated with the MSI P45 Platinum mobo that would make this a pain to set up. Anyone else running a RAID 0 with this mobo and having good results? Would it even be worth it?
    I was told my several different people in the gaming community, that RAID 0 really speeds up map loading, which would be great. I would be backing up the array to another internal drive using True Image.
    Any advice would be great!! 

    Quote from: Jack t.N. on 20-May-09, 03:16:19
    Only, if you set the controller to AHCI Mode (which would not really be a problem either).  You probably won't need any additional drivers when the controller is working in IDE Mode.
    If you have to install drivers, use the latest ones from the JMicron FTP Download Server:
    ftp://driver.jmicron.com.tw/jmb36x/Win2k_xp_Vista/
    Ok, well I won't have my new storage drive until Thursday. I will run HD tune on the drive connected to both different controllers and see what is the fastest.
    I know we talked about this just a little. Still wondering about the RAID drives, or any drives attached to the ICH10R's SATA connections when it is set to RAID in the bios. The drives, including my SATA CD/RW drive does not show under "Standard CMOS features". Just #7 and #8 of the JMicron's show since they are still set to IDE in the bios.
    You commented with:
    "They are now Controlled by the ICH10R Firmware.  Look here":
    --> Integrated Peripherals --> On-Chip ATA Devices --> AHCI Devices Group
    --> Integrated Peripherals --> On-Chip ATA Devices -->
    Those locations are just where you set the RAID mode. There's no actual drives listed there. I do see a screen popup when booting my system with the two RAID drives saying "ok" and bootable. Plus I see them in the Matrix storage console. Is this normal then?  There really is no place when you search through the bios that you can see them listed??  I can hit the Ctrl and I keys and go into the actual RAID bios, but I don't see my RAID drives listed in the actual bios.
    Am I explaining this right??  Just wanting to make sure everything is working right.  It sure seems to work well with bench marks. Here's a shot of my array with HD tune.  I'm thinking that burst rate can't be right.

  • Msi p45 platinum and e5300 HELP

    Hello! Can you help me with this?
    bios v1.6
    Intel e5300 - 2,6ghz
    Msi p45 platinum
    2gb trancend ddr2 667
    What function to enable,what to disable. Also,have I hardware overclock fsb jumpers (now sets to 200Mhz)-JB1 and JB2. And how to decrease cpu ratio if I have to( now is 200x13=2600Mhz). Also what dram ratio etc...
    I'll be greatefull if somebodu help me,I just wanna overclock processor to 3gHz for every day,not 24/7, maybe 12/7...THANX and sorry for my bad English

    hello! I try that,remove both the oc jumper,and I CAN'T EVEN RUN THE BIOS    So after couple restarts, i shut down pc and se jumpers to 200-266 mode. Disable what you said,set fsb 260 x multiplier 11,5 and get 3ghz. Some programs seys core 1 and 2 speed 3371mhz? I set cpu voltage to 1.32, little increase the ather voltages... With max load max temperature with core temp is 63c after couple hours. Should I do something to increase more speed or is better to leave it like this? Or try set jumpers to mode 266-333 and decrease cpu multiplier wuth more fsb?

  • MSI P45 Platinum and Neo2-FR

    Hello everyone!
    I have small question will P45 Platinum and P45 Neo2-FR work fine with those memories OCZ DDR2 PC8500 4096MB KIT, Reaper HPC, 2x2048MB, Heatpipe, (CL5-5-5-18) ?

    Quote from: Jack the Newbie on 04-October-08, 18:05:31
    A few facts about the P45 Chipset and those memory modules:
    1) According to Intel Specifications, the Intel P45 Chipset natively supports DDR2-667 and DDR2-800 modules, that is it.
    2) Those OCZ Modules are essentially DDR2-800 modules (use DDR2-800 chips).  DDR2-1066 is an overclocking rating that will force you to overvolt these sticks above DDR2 standard voltage.
    3) EPP profiles are pre-programmed OC profiles that are not fully supported on Intel Chipsets but are for NVidia Chipsets only.
    The bottom line is:
    -> To run those modules @standard DDR2-800 speed should be no problem (neither on the P45 Platinum nor on the P45 Neo2-FR.
    -> Trying to get the system stable @DDR2-1066 speed may or may not work stable, as this means overclocking both the memory controller AND the modules. So, get ready to some tweaking of memory related BIOS settings (inlcuding memory voltage, MCH Voltage, DDR reference voltages and timings) to find stable settings for non-standard clock speeds.
    So I shouldn't have any problems to start computer after I connect everything? And what IF I will be unlucky and those memories won't work ?

  • MSI P45 Platinum and e8400 at 4GHz but Vcore at 1.512V

    Ok, so I hit the big "4" but with a price of using 1.5+ :( on vcore.  Using Orthos to stress, my temps on both cores are 60C or below.  That seems acceptable.  Btw, I left Orthos running for 30 minutes then turned off and went to bed.  Any advice is welcome on lowering my vcore for longevity?

    Quote from: iTalisman on 14-November-08, 14:21:38
    I just raised the vcore to 1.3v. But the board has a vdroop. If I set it up at 1.3, it takes up to 1.32+. Currently at 400X9=3.6. Memory divider 1:1=800 (4-4-4-12). Testing if its stable. Intel Burntest for 20 minutes seems ok. Temps are 52 and 55. Gaming is ok for a few hours. BIOS is currently 1.53 beta. I am still confused about the n.bridge setting in cell menu. There are 4 options....not sure about those. And I've pulled up those FSB jumpers. So its set to 333-400. By the way....what about performance BIOS....give me some pearls about it...since u r using. The pro's and con's....
    What kind of vdroop are you seeing?  Your setting seems okay for that configuration.  N. bridges settings are the MCH voltages and MCH GTL REF.  If you want to go higher say 400FSB+, than set MCH Voltage to around 1.4V and bump your vcore up to 1.4V.  However, that will generate heat and if you don't have adequate cooling (e.g. water) then there will be problems. 
    Also, I have no idea about the differences in performance and non-performance bios and I have not personally tried them all, just A7512IMS.P0D, A7512IMS.153, and A7512IMS.P0M.  I really don't understand how they label the bioses either since its not too clear.  For example, how do you know A7512IMS.P0M is V25.0B22?  It's only after you flash the bios and look on the startup screen.  This confuses people in my opinion.

  • MSI P45 Platinum and 6 HDDs

    Hello friends,
    i have this strange problem, i have 6 hard disks connected to ICH10R on my mobo. Everything is detected in BIOS on ICH10R. I have created these volumes:
    RAID0+RAID1 on first and second disks and other 4 disks are in RAID5,BUT:
    when my OS load, storage manager find degraded raid5 volume and missing the last (6th) disk.Someone have any ideas?Thanks in advanvce!
    My OS: Windows XP x64 SP2
    last version of the matrix driver 8.8.0.1009

    I have done some more continuous tests with intelburn test and memtest and i think already, that definitely problem is NOT CPU and RAM.
    I have done some tests on hdds and the results on all 4 disks are the same:
    [SELF DIAGNOSTIC (ESTOOL v2.11a)]
    Model Name : SAMSUNG HD103UJ
    Rom Revision : 1AA01113
    Serial Number : S13PJ1CQ610012
    Drive Size : 953868MB (LBA : 1953523055)
    Test Loop Number : 1/1
    >> READ DMA : Testing... Pass !
    >> CHECK S.M.A.R.T. : Testing... Pass !
    >> SPIN DOWN / UP : Testing... Pass !
    >> SIMPLE SURFACE SCAN : Testing... Pass !
    >> WRITE VERIFY : Testing... Pass !
    >> RANDOM SURFACE SCAN : Testing... Pass !
    >> READ SURFACE SCAN : Testing... Pass !
    >> RAM VERIFY TEST : Testing...
    Service Code => AJ29 : RAM Error.
    Error : Command timeout
    >> MULTIPLE READ TEST : Testing... Pass !
    Service Code => AJ29 : RAM Error.
    Scan Elapsed Time : 03:24:30
    Error Occured Test Loop Number 1
    Test was completed.
    There are 3 disks with fw 1AA01113 and 1 with 1AA01119. I don't know what that RAM error means (maybe disk cache), but i don't think this is the problem (the 4 disks are buyed from different time period), maybe just estool has some bug.

  • Problem with MSI P45 Platinum DDR2 mainboard and Corsair Dominator PC8500C5D Ram

    Hi, I have encountered with a problem.
    First I had
    MSI p45 platinum ddr2 bios ver. 1,4
    Intel E8400
    Corsair Dominator PC8500C5D 2x1Gb
    2 Asus ATI EAH 3870 Crossfire
    and it was running with windows XP without any problems.
    Problems began when I decided to upgrade to 6Gb of ram and to install Vista 64. Ram modules witch I bought are the same Corsair Dominator PC8500C5D, but 2x2GB.
    When i put them together adjust voltage 2.1v and timing 5-5-5-15 they fail mem test with huge amount of errors.
    when I test only 2x2gb modules memtest sometimes doesn't open at all, sometimes just stops working on 8 minutes of test. couple of times they completed memtest without any errors.
    Can someone advice what should I do and what could the problem?
    Thank you for your answers.

    Quote from: obsessed on 15-October-08, 18:20:44
    Corsair Dominator PC8500C5D 2x1Gb
    Problems began when I decided to upgrade to 6Gb of ram and to install Vista 64. Ram modules witch I bought are the same Corsair Dominator PC8500C5D, but 2x2GB.
    1) the modules are not the same (the DDR2 chips are different)
    2) as general rule, mixing 2x1GB with 2x2GB is a bad idea.
    cheers

  • Add a new 4tb hdd to msi p45 platinum ?

    I'm planning to add a new 4TB western digital, caviar green  HDD's for my msi p45 platinum motherboard ist work will or use 3 tb .
    thank you

    Just some notes regarding large drives on the older chipset boards.
    The P45 Plat has
    • SATAII controller integrated in ICH10R/JMicron® 363 chipset
    - Up to 3Gb/s transfer speed.
    - Supports six SATAII ports by ICH10R
    - Supports two SATAII ports by JMicron 363, support SATA RAID 0/1/JBOD.
    In principle the ICH10R allows amongst Raid capability also the ability(potentially) to handle up to 2TB in AHCI.
    What other users with similar boards have however commented on is that they were able to use up to 3TB drives on the JMicron controller, obviously with the latest firmware for that controller and also AHCI. We all know that the JMicron ports are a bit slower than the Intel ports, but that is evident with Asmedia as well.
    So when you do test, check both your Intel and JMicron ports and see what they report as the drive capacity in the BIOS.

  • Overclocking Q6600 with MSI P45 Platinum

    Hi again!
    I need some advice regarding my OC settings.
    Unfortunately, im an unlucky owner of the infamous Q6600 L8XX batch which has a high VID (1.3250v)
    Anyway, I was able to reach 3GHz stable with these settings:
    MSI P45 Platinum official v1.5 bios
    Motherboard OC Jumper set to: default
    ================================
    C1E: Disabled
    Green Power: All Disabled
    ================================
    Multi-Step OC Booster: Mode 1
    DOT Control: Disabled
    Intel Eist: Disabled
    Adjust CPU FSB Frequenxy (MHz): 333
    Adjust CPU Frequency: 3000
    CPU Multiplier: 9
    ================================
    Advance DRAM Configuration: Manual
    Enhanced Settings: Enabled
    NB Drive Config: auto
    CAS Latency (CL): 5
    tRCD: 5
    tRP: 5
    tRAS: 15
    Advanced memory Setting: Disabled
    FSB/DRAM ratio: 1:1.2
    Adjusted Dram Frequency: 800
    ================================
    ClockGenTuner:  No Changes Done
    Adjusted PCI Frequency: 37.5
    Auto disable DRAM/PCI Frequency: Disabled
    ================================
    CPU Voltage: 1.3175v
    CPU GTL REF0: auto
    CPU GTL REF1: auto
    Dram voltage: 2.100v
    DDR_VREF_A: auto
    DDR_VREF_B: auto
    MCH Voltage: 1.4v
    MCH GTL REF: auto
    VTT FSB Voltage: 1.35v
    ICH Voltage: 1.52v
    ================================
    Spread Spectrum: Disabled
    My goal is set at 3GHz and to get a lower cpu voltage (lower than my current 1.3175v), but anything below 1.3175v restarts when i stress test using OCCT. I've run memtest and it's ok. Can anybody advise which voltage I can configure to lower my cpu voltage? Also, is 333 x 9 to achieve 3GHz better? Or should I go with 375 x 8? Thanks! Btw, I plan to maintain these settings for the remainder of my CPU's life..  :D

    thanks for the tip. i'm currently logging all my OC settings in an excel file. i just finished played an hour of COD4 without any restarts or instability. currently my settings are just the same except CPU voltage is at 1.344v and i reduced my Dram voltage to 2.0v. running memtest for over an hour, 2 passes already with no errors. i'll stress test it over the weekend.
    i have a question though. a lot of people are suggesting a 1:1 FSB/DRAM ratio. but using 333x9 settings @ 1:1, you get 667.. i'm using 2x 2GB GeiL PC6400 800, that's why i used the 1:1.2 FSB/DRAM ratio to get 800. is it ok to keep using the 1:1.2 FSB/DRAM ratio even though people say 1:1 is the ideal ratio? many thanks for the reply

  • About TPM module MSI P45 platinum

    Hello.
    I need some information about this function, supported in MSI P45 Platinum - TPM module. Where can i buy such thing, and eventually prices for it.
    Thanx in advance!

    TPM is nothing MSI Specific.  Please read this article first:
    http://en.wikipedia.org/wiki/Trusted_Platform_Module

  • E8400 on an MSI P45 Platinum

    I just got done reading the guide on tweaking VTT/GTL which helped me get a better grasp about the awesome settings the P45 have.
    Anyway I have a bit of a dillema, I can't seem to get 4.0Ghz without cranking my settings up to this:
    Vcore = 1.525v (This will fry it eventually)
    CPU GTL REF0 = AUTO (For now)
    CPU GTL REF1 = AUTO (For now)
    DRAM Voltage = 2.100v (Manu specs)
    DDR_VREF_A = AUTO (For now)
    DDR_VREF_B = AUTO (For now)
    MCH Voltage (Is this the Southbridge?) = 1.556v (I have no idea what to set this to, I just cranked it up as high as it would go)
    MCH GTL REF = AUTO
    VTT FSB Voltage = 1.60v (What the hell is VTT?)
    ICH Voltage (Is this the Northbridge??) = 2.12v
    The problem with this is I'm going to cook my system...the funny thing is I can remove the jumpers and run my CPU at 3.6Ghz and all stock voltages without a single problem - however going even 1Mhz above this requires me to crank the hell out of this system.
    Anyone here have any settings they use for this board w/ an E8400? I'm kind of out of ideas at this point.
    Specs:
    MSI P45 Platinum
    Intel E8400 Core2Duo @ 3.0Ghz
    OCZ OC RAM DDR2-1066 @ 5-5-5-15-2T and 2.1v
    Antec TruePower 750w w/ (4) Independent 12v rails

    Quote
    ...the funny thing is I can remove the jumpers and run my CPU at 3.6Ghz and all stock voltages without a single problem
    Thats a good starting point. Set BIOS to default and then ensure your memory is at DDR2-800 at ~1,9V.
    From there start increasing your FSB. I think you will have a better chance at what you are trying to achieve with a lower memory frequency. See how far you can go that way without changing any other voltages, but always check your V Core under load as you increase the frequency.
    I have had my proc at up to 3,7GHZ (board jumpers removed) all other BIOS settings being stock/auto, but I manually kept my DDR at 800.
    My  core Voltage will rise to 1,296 under full load at that freq, which is still below the Intel spec max of 1,3625 "Table 2-3. Voltage and Current Specifications in the Intel spec sheet". So I know there is room for more. My CPU core temps will be between 55 and 60C depending on the auto speed-up of the cooler, which I must say is very effective.
    Running some real world tests though, i.e. 3D gaming, I found that the increase above the 3,4GHz I am running now, is hardly worth the additional heat and obvious associated higher voltages.  My chipset especially heats up to about 55C and I need to take the passive cooling off at some stage to check the MSI factory paste.

  • Msi p45 platinum - freezes after power save turns off displays

    Just put this computer together, everything is stock, no overclocking. Seems to run fine, played a few hours of modern warfare 2 with no issues.
    I noticed It seems to freeze after the monitor gets turned off by the power save mode. I just tested this by setting it to turn off displays after 1 minute of inactivity, waited watched the monitor turn off, then I went to the move the mouse and the screen came back on but the cursor would not move. sometimes the screen will not even come back on.
    I have turned the computer on, left the room while it was booting to eat breakfast or take a shower, came back the screen was still on but the computer was frozen. Window 7 login screen was up, but there were some graphic glitches. this has happened a couple of times.
    If I manually put the computer to sleep it seems to come back properly.
    msi p45 platinum 1.6 bios, optimized defaults loaded
    e5200 intel dual core @2.5 ghz, 200FSB 12.5 multiplier
    4 x 1gb ddr2 (800mhz, nanya brand)
    nvidia gtx 260 (195.63 drivers x64)
    win7 ultimate x64
    enermax 720w powersupply

    I think it might be the video card or power supply. Was building two systems,
    second system has identical motherboard, processor and ram,
    galaxy gts 250 instead of the evga gtx 260.
    antec 430 earthwatts  instead of Enermax EIN720AWT 720W Power Supply
     Installed from same OS disc and same set of drivers. Second system seems to operate the powersave mode for the monitor correctly. Will have to do some testing switching videocards tonight.

  • MSI p45 Platinum LEDS

    Hello,
    I am a student Studying in Male', Maldives. Iwould like to know this MSI p45 platinum Motherboard.
    If anybody could help it would be really very helpful. So the problem is that the motherboard has a green led 3 red leds showing so i want to know how i can change it to green according to the manual.
    LED 12, LED 8, LED 14, LED15 are Red and the LED 10 is green so.. how can i change LEDS 13, 7, 11 to green..
    thanks..
    Ximan

    Quote from: Ximan on 01-March-11, 18:29:43
    Hello,
    I am a student Studying in Male', Maldives. Iwould like to know this MSI p45 platinum Motherboard.
    If anybody could help it would be really very helpful. So the problem is that the motherboard has a green led 3 red leds showing so i want to know how i can change it to green according to the manual.
    LED 12, LED 8, LED 14, LED15 are Red and the LED 10 is green so.. how can i change LEDS 13, 7, 11 to green..
    thanks..
    Ximan
    Most probably same problem as mine, ram no seated properly, I unplug and plug many times, sometimes have to lay the cpu (if it a tower) on its side, then boot up can function.
    My problem as follow
    https://forum-en.msi.com/index.php?topic=144468.0
    Description of LED array status
    https://forum-en.msi.com/index.php?topic=123890.0
    Nothing to do with LED status but problem related to USB
    https://forum-en.msi.com/index.php?topic=123722.0

  • Problems Powering up MSI P45 Platinum board

    I've currently started a new build using the following equipment:
    Coolermaster COSMOS 1000
    MSI P45 Platinum
    Intel Quad Q9550 Processor
    2 x 2gb OCZ Memory
    Sapphire ATI 4790 HD 1gb Graphics Card
    PC Cooling 750W Silencer PSU
    Wired everything up, connected all the connectors.  When I go to power up the system, I get a Red LED 3 but no fans or anything spins up.  Switched out for a known good power supply and received the same problem.  Not sure where to go from here?

    Hi,
    take the board out of the case to test it on a non-conducting surface in barebone configuration (CPU, one memory stick, video card, Keyboard and power connectors, nothing else).  Make sure every kind of connection (front panel etc. to the case is removed).
    Then clear CMOS with main A/C power cable removed from PSU and try to power-Up the board.  Try both of the following methods to power-up the system:
    1. use the little red onboard-power-on-button (make sure you don't confuse it with the reset button)
    2. shorten the two pins of the board's pin header that are usually hooked up to the case's power-on button with a screwdriver

  • Problems Powering up MSI P45 Platinum board --LED3 still flashing

    Hello all
    I've currently started a new build using the following equipment:
    Coolermaster COSMOS 1000
    MSI P45 Platinum
    Intel Quad Q2600 Processor
    1200 MHz patriot  2x1GB Memory
    xfx 9800 HD 1GB Graphics Card
    power supply Trust switching power supply ATX 400W&P4 :
    220 v AC
    +3.3v---20A
    +12v ---18A
    -12v --- 0.5A
    +5v ----24A
    -5v ---- /
    +5v sb ---2A
    Wired everything up, connected all the connectors.  When I go to power up the system, I get a Red LED 3 but no fans or anything spins up.  Switched out for a known good power supply and received the same problem.  Not sure where to go from here?
    and also  i press cmos reset button and nothing happing

    Quote from: flink on 30-April-09, 13:56:54
    i'm sure the hole for the cmos clear button in the i/o shield is the problem. the button is pressed by the i/o shield and your pc won't start.
    a well known problem. 
    I remember reading about this issue before I built my P45 Platinum system. I made sure during the build that the button was not being pressed by the i/o shield.

Maybe you are looking for