Msi p4n diamond and memory module setup for dual channel reading

hi,
ive just built my mum a pc using a msi p4n diamond mainboard which has 2 gig of ddr2 667 mhz memory, just wondering how to go about setting it up to dual channel as its currently showing up in boot post screen as being single channel.. Now correct me if i'm doing wrong but it has 2 green slots and 2 orange slots, should there be 1 stick of ram in green and one stick of ram in the oarnage slot to show dual channel or both sticks as they are situe at present in green slots please..
system spec is below..
mainboard - msi p4n diamond
cpu - intel pentium 4 @stock speed 3.0 ghz HT
geforce 8800 gs @ 512 meg of ram
500 gig s-ata hard drive
600 w coolmaster psu
2x1 gig kingston ddr2@667 mhz
first release bios
thank you and hope you can advise me..

It's in the manual, if you don't have one you can download from here:
http://www.msi.com/service/download/manual-4385.html
If both sticks are in green as you say then yes it's single channel. For dual channel you want to leave 1 stick in DIMM1, green slot nearest CPU & move the 2nd stick to the orange DIMM3 slot.
From left to right DIMM1/2-green, DIMM3/4-orange, dual is 1 stick DIMM1 & 1 stick DIMM3 or 1 stick DIMM2 & 1 stick DIMM4 or 4 sticks all four slots filled. Single channel is 2 sticks in green slots or 2 sticks in orange slots or not recommended is 3 sticks in 3 of the 4 slots.

Similar Messages

Re: MSI 785GM-E51 and memory modules problems -l- Split

I am using AMD PHENOM II 1055 125w CPU on MSI 785GM-E51. Memory Corsair XMS3 DDR3-1600 x4
I can put memory in slot 1 and 3 it will boot fine.
If I install DDR3 in slot 1 and 2 the system will not boot. If I full populate all the memory slots it will not boot
In both scenario's after the system does not boot and go back to just using slots 1 and 3 the system boot with CMOS checksum error and need to go in to BIOS setup. All the changes need to be made again, saved and exit and it reboots fine.
I have already attempted to setup the memory speed to 1333 and 1066 with no luck. Any ideas?
785GM-E51/BIOS 2A0, Phenom II T1055 @ 2.8 GHz, 125W Stock AMD Heat sink&Fan
Corsair 2x2GB CMX4GX3M2A1600C9, 9,9,9,24, 1T, 1.47V, 1600 MHz --------- 2 kits
ESXi 4.1
Antec 650 Truepower
ATI x600 PCI-e
Adaptec AAR-2610A with 5 WD Caviar RE WD2500SD-01KCB0 250GB RAID-5 Configuration
NEC ND-2501A DVD-Burner

Topic split, don't hi-jack other peoples topics. >> Please read and comply with the Forum Rules <<
Provide more information on your system, read this: >> Posting Guide <<
See my signature for example of information to provide.

MSI 785GM-E51 and memory modules problems

Could anyone help me with one problem. I have motherboard MSI 785GM-E51 and 4 memory modules GOODRAM GR 1333D364L9/2G. But when I'm inserting ALL modules my system not starting (even POST procedure). So working variants - when I'm inserting:
- one module in first (boot) slot
or
- they inserted in first and third memory slots
Any ideas?

It is not motherboard problem, but processor itself - I have AMD Phenom II X4 965 Black Edition 3,4 Ghz Core Revision C2 and this revision (according to the article: http://www.fcenter.ru/online.shtml?articles/hardware/processors/27650#02) has problems with support memory modules DDR3-1333 Mhz more than 2 modules. Conclusion - either adjust BIOS settings concerning memory timings and memory controller voltage or replace this kind of processor with the same type but with core revision C3

MSI P4N Diamond, Socket 775 compatibillity

Could anyone please tell if there are any known compatibility issues between a MSI P4N Diamond, Socket 775 motherboard and a PowerColor X800 GTO, 128MB, 256bit video card? I have heard that this video card might have some issues used together with mb based on NVIDIA chipset. Is this true? There some bios updates that can fix such issues? Thnks.

I have sent an e-amil to MSI support and I got this answer:
dear user :
in this case , we will suggest you to use anlther vga card like X800GT /X850 ,
because the are a few customer reported for these
are some status happen if they hope to enable dual-display feature with X800GTO
+ mainboard based on nvidia chipset , and this
status might happen because there are some resource conflict between the X800GTO
and them/b bios .
Any advices?

I need to know thelist of bapi's and function modules used for transaction

I need to know thelist of bapi's and function modules used for transaction in order to use these FM or BAPI in reading some fields of equipment master and functional loocation.Can any one suggest me some methods...or do i need to write a report for the same.

Steps to find the BAPI/function modules used in a transaction
1) Find the package of the transaction thro' SE93.
For example the package for the transaction VA03 is VA
2) Go to Se80, key-in the package (say VA)
3) You can see the function modules under the folder finction group and
you can see the BAPI's under the folder Business Engineering-> Business Objects-> double click on the released methods of the Business Objects

To know thelist of bapi's and function modules used for transaction IH10

I need to know thelist of bapi's and function modules used for transaction in order to use these FM or BAPI in reading some fields of equipment master and functional loocation.Can any one suggest me some methods...or do i need to write a report for the same.

hi,
provide report name (here: RIEQUI20)
goto se38 - utilities - cross reference - function modules
or use report RPR_ABAP_SOURCE_SCAN
with search string call function
A.
Message was edited by:
Andreas Mann

VAT and Withholding tax setup for Philippine

Hi ,
Anyone is familiar with the VAT and Withholding tax setup for Philippine.
What is the VAT and WHT config in order to fuilfil the following example.
Appreciate if someone is able to provide me some help on this. Thank you.
Invoice Amount of P 1,120.00 gross of VAT
Services Sales to Private
ENTRY TO RECORD REVENUE          Debit     Credit
Accounts Receivable                                1,120.00
     Vat Consultancy Set-Up                               120.00
     Revenue                                                 1,000.00
ENTRY UPON COLLECTION
Cash in Bank                                                  1,100.00
Taxes Payable - BIR ITR                                 20.00
Vat Consultancy Set-up                               120.00
     VAT Consultancy Payable                               120.00
     Accounts Receivable                            1,120.00

Additional Information
Value Added Tax Reporting:
Advance Return for Tax on Sales/Purchases (VAT Reporting)
Use
In the Philippines, companies are required to submit Bureau of Internal Revenue (BIR) forms 2550M for the monthly (value-added tax) report and 2550Q for the quarterly VAT report. However, these forms also include information not provided by the SAP System, such as advance payments. Using the Advance Return for Tax on Sales and Purchases report, you can print the relevant VAT data and enter it in forms 2550M and 2550Q.
Integration
The report is based on the SAP List Viewer (ALV), which enables you to define your own display variants, according to the BIR requirements listed below.
Activities
To access the report, from the SAP Easy Access screen, choose Accounting --> Financial Accounting --> General Ledger --> Reporting --> Tax Reports --> General --> Advance Return for Tax on Sales/Purchases --> Advance Return for Tax on Sales/Purchases.
You need to make the following settings, in addition to your specific selection criteria:
Under                         Set the following indicator(s)
Output control                         Read address data
Output lists                         Output tax: Line items
                                            Input tax: Line items
You need to define your SAP List Viewer display variant to include the following data on the VAT report, as required by the BIR:
u2022     Reporting company's name and TIN
u2022     Vendor or customer name
u2022     Vendor or customer TIN
u2022     Vendor or customer address
u2022     Document date
u2022     Document number
u2022     Reference number
u2022     Invoice amount
u2022     VAT amount
Withholding tax reports
Generic Withholding Tax Reporting
Use
You use the Generic Withholding Tax Reporting tool to generate withholding tax data for withholding tax reports submitted to the Philippine Bureau of Internal Revenue (BIR) and vendor certificates, as follows:
u2022     BIR form 1601 u2013 Monthly Remittance Return of Income Taxes Withheld
u2022     BIR form 2307 u2013 Certificate of Creditable Tax Withheld at Source
u2022     BIR form 1604 u2013 Annual Information Return of Income Tax Withheld on Compensation, Expanded and Final Withholding Taxes
Features
SAP delivers standard report variants and Smart Forms for each of the reports and the certificate, which are listed below.
SAP also provides a display variant for the output lists, 1SAP, which you can specify under Output control and lists in the Display variant column.
BIR 1601
SAP provides withholding tax data for page 3 of the form. The form comprises three sections u2013 expanded withholding tax, final tax based on the regular rate, and final tax based on treaty rates. Within each of these sections, the data is summarized according to the nature of the income payment (ATC code). For more information, see Withholding Tax Code.
The predefined report variant for BIR 1601 is SAP&PH_1601, and the Smart Form is IDWTCERT_PH_1601.
BIR 2307
The predefined report variant for BIR 2307 is SAP&PH_2307, and the Smart Form is IDWTCERT_PH_2307.
BIR 1604
You use BIR form 1604 to report expanded and final withholding tax for all nonemployee transactions.
SAP provides the three required sections of form 1604: alphalists 3, 4 and 5 (schedules):
Section of BIR 1604 -DESCRIPTION - Predefined report variant - Smart Form
Alphalist 3     Payables subject to expanded withholding tax     SAP&PH_1604-3     IDWTCERT_PH_1604_SCHEDULE3
Alphalist 4     Payees subject to final withholding tax     SAP&PH_1604-4     IDWTCERT_PH_1604_SCHEDULE4
Alphalist 5     Other payees whose income payments are exempt from withholding tax issued but subject to income tax     SAP&PH_1604_5     IDWTCERT_PH_1604_SCHEDULE5
Prerequisites
For each withholding tax report, note the required Customizing settings for the corresponding output group.
Activities
To access the report, from the SAP Easy Access screen, choose Accounting --> Financial Accounting -->Accounts Receivable --> Withholding Tax --> Generic Withholding Tax Reporting.
The Generic Withholding Tax Report has several options for reporting.
The report can be run without the Output Group field populated, or it can be run with one of the PH1 to PH5 options as it relates to the reporting forms/requirements
Hope this piece of information is helpful to you.

How to find the current CPU and Memory (RAM) allocation for OMS and Reposit

Hi There,
How do I check the CPU and memory (RAM) allocation for the OMS and the Repository database? I'm following the "Oracle Enterprise Manager Grid Control Installation and Configuration Guide 10g Release 5 (10.2.0.5.0)" documentation and it says to ensure the following:
Table 3-1 CPU and Memory Allocation for Oracle Management Service
Deployment Size Host CPU/Host Physical Memory (RAM)/Host Total Recommended Space
Small (100 monitored targets) 1 1 (3 GHz) 2 GB 2 GB
***Table 3-2 CPU and Memory Allocation for Oracle Management Repository***
Deployment Size Host CPU/Host Physical Memory (RAM)/Host Total Recommended Space
Small (100 monitored targets) 1 1 (3 GHz) 2 GB 10 GB
Thanks,
J

Hi J,
This is the minimum requirement. However It will work fine.
Also read below article on "Oracle Enterprise Manager Grid Control Architecture for Very Large Sites"
http://www.oracle.com/technology/pub/articles/havewala-gridcontrol.html
For GRID HA solution implementation please read :
http://www.oracle.com/technology/deploy/availability/pdf/MAA_WP_10gR2_EnterpriseManagerBestPractices.pdf
Regards
Rajesh

[nVidia Series] is it MSI P4N Diamond compatible with Gigabyte 3D1 (Dual Core 66GT)

yesterday i juz got a Gigabyte 3D1 graphic card..so i wanna know..is it MSI P4N Diamond compatible with this graphic card?
thanx

Quote
The problem is, this card was only intended to ever be used on that motherboard. It may work in single GPU mode on other boards, but results will vary on other SLI boards.
This line is from the referenced article. It seems to imply that card is intended to be used with the Gigabyte board.

MSI P4N Diamond coming soon

I found this MSI P4N Diamond , worth a wait...

Here's another one...
http://www.hardwarexl.com/index.php?option=com_content&task=view&id=477&Itemid=2

External hard drive setup for time machine reading as a virtual cd

Why is my MacBook Pro reading my external hard drive setup for time machine reading as a virtual cd?
Thanks

Hi Christian,
Is this something that has happened from the start? If so, I would reformat the disk and setup TM from scratch again.
Prepare the external HD by connecting to the Mac, open Disk Utility, select the manufacturer’s name of the external HD, select Partition and choose GUID Partition Table, format to Apple OS Extended (Journaled); quit Disk Utility.
Open System Preferences.
Click on Time Machine.
Click on “Select Disk.”
Click just to the left of "On" to turn TM on if it's not already on.
Click on the disk or partition you want to use.
Click on “Use for backup.”
Leave external HD connected, and TM will automatically do its thing.

I wan't setup for sccm 2012 read only console

i wan't setup for sccm 2012 read only console

There is role read only analyst please assign same to user or group.

New Bios Update for MSI P4N Diamond to support 9XX D series

Hi, i recently bought a P4N Diamond with a 830D cpu. I want to upgrade to a 940D but unfortunately the MOBO does not support it as yet ( i had a look in your mobo support status) so was just wondering when and if an update will come out to support it.
Thanks

Hmm so that means Possible Yes or definite no that it wont be supported.
Another problem im having with my setup is this it keeps shutting down randomly on its own.
with overclocking and without overclocking. i have gone up to 3.1 ghz 3.2 ghz 3.3 ghz and it shuts down on its own or sometimes it justs freezes
my setup is this
p4n diamond
intel 830d 3.0ghz
500w antec neo SLI PSU
OCZ dual channel ddr 2 2gb ram 4-4-4-12 timings
250 gb WD sata 2 KS series
XFX XXX edition 7900GT GFX
can anyone help??

MSI P6N Diamond and very slow BIOS menus

I'm having problems with my new setup. My setup is as follows:
MSI P6N Diamond with 1.1 bios update
2 x OCZ Platinum Revision 2 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model OCZ2P800R22GK
XION Supernova XON 600W Power Supply
Intel Core 2 Quad Q6600 (not overclocked yet, having problems whenever I change settings)
EVGA GeForce 8800GTS 640MB Video Card
I'm running Vista 32bit fine as far as I can tell, everything is pretty snappy and other programs are running fine, but the machine is very slow to post and running the bios menus is a painful process as it takes about 2-4 seconds to switch selections. I tried running the board with 1 stick of ram in slot 1, with slots 1 & 3 and all 4 and it made no difference. I had a USB card reader plugged in and then removing it seemed to make a difference for a while, the BIOS menus ran as I expected, very snappy. Also anytime I switch the CPU clock from automatic to manual the computer won't post and i have to reset the bios
Anyone have a clue what could be causing this slowness and my inability to overclock the cpu?

I will be getting the Q6600 in 1 week, :D. The new G0 stepping as well :D. I'm excited.
Are you using XP or Vista? I have had no distortion or pops with my sound. Although, from what I hear the drivers for XP or much more polished than those for Vista. This is a Creative issue, and not an MSI issue. Lots of people are having problems with Vista with the standalone Creative cards as well.
I overclocked my E6700 to about 3.5Ghz, and hit a temp wall based on my ambient temps. I probably could have gone higher if it was cooler in the room that houses the computer. Although, the temps have dropped dramatically after the AS5 has cured, probably could get it pushed up a bit higher. Hopefully I don't have problems with it when the Q6600 comes in.
If you got the older B3 stepping version, it will run a bit hotter and will be much harder to OC to higher speeds because of this. I've found the P6N Diamond to be very OC friendly and like all the options it gives. The only thing I don't like is the adjustment of the Vcore lists the # above stock, instead of the absolute #. Sometimes the Vcore it auto assigns isn't 100% correct I've heard so it'd be nice to know what that auto value is. The Vcore reading you can read in the monitor section fluctuates a hair in each direction of 1.3 for me when at stock, so I assume it was 1.3 stock.

P4N Diamond and Pentium D problem

Hi,
Have just bought the P4N Diamond motherboard, and a Pentim D 830 processor.
When switching on the status led shows four red lights. According to the manual this means that the processor is defective.
Have taken the processor in and out many times, but no luck.
Any other ideas ? Any assembly errors I could have made ?

IJRC, For your set up do the following:
The best way to get your system up to make sure that you have BIOS version 1.3 and up. Any BIOS version before this will not see the Pentium D. If you dont have this BIOS or are not sure it might be best if you call MSI and have them send you out a BIOS chip with the updated BIOS version on it.
-Make sure that you only install windows with one stick of RAM
-Do not connect any USB devices untill windows is up and running.
-Your MOBO takes alot of power, so make sure that you have a quality PSU as well as it having plenty of amps on the 12v rail. (As per the P4N manual p.10, 450watts and atleast 20amps on the 12v rail is recommended for system staibility.)
-Drivers for me were not that much of a problem except for my monitor, but my GPU sees it for what it is and thats what matters. Ofcourse if you dont have the internet up and running getting drivers might be a problem.
- As long as your follow these steps you should be fine with installing windows 64x. To be safe just download the Marval Lan Eathernet Drivers and burn them to a cd before you start your build. That way you can access the internet to download 64x drivers. For the most part you shouldnt have a problem getting drivers...if you have an hp printer you will have a problem though.
GL and write back if you have problems...i think that i have been through them all with this MOBO and the Pentium D. However with the help from this fourm i think that i have everything under control.

Msi p4n diamond and memory module setup for dual channel reading

Similar Messages

Maybe you are looking for