MSI P67A-GD53 (B3) Boot loop after BIOS update

Hi,
I've just updated my BIOS to 7681v42 from an earlier version (can't remember which one exactly) and after the update I am stuck in a boot loop. The computer turns on for about 5 seconds or so and then switches back off, the CPU fan, motherboard fan & video card fan spin for a few seconds then power is cut.
I've tried booting up with nothing else connected (no vga, memory, hdd, empty USB slots) to no avail. I have tried resetting the CMOS as well but I don't get any further than the reset loop.
Can anyone suggest something? Is there any way to force the MB to use the backup BIOS?
Thanks in advance.

You can try doing this again with a single stick of ram or some different ram, but more than likely you will need to rma the board for re-flashing.

Similar Messages

Z68a-gd65 boot loop after bios update using USB

Hi there,
My z68a-gd65 (G3) went into a boot loop after I did a bios update from a USB key that I installed using the latest BIOS version on the MSI site 7681vP8.zip
After the system restarted, it keeps booting up for 5 seconds and then shutting down, I removed all external devices and the Geforce GTX 550 Ti card and used the onboard card, but still no change...
Is there a way to set the board to factory defaults again???
Marcel

Hi there,
Maybe for others to solve the same problem, I found out what was the cause of this problem, I had a USB/Firewire card installed in the PC, after removing it the BIOS update could proceed from the USB stick as planned.
After the update though, my USB/firewire card can still not be installed back into the slot, because doing so will make the boot loop appear again, very odd!
Does anyone know why this new BIOS will not work with the card that has been inside my PC for 2 years???
Marcel

P67a-c43 boot loop after bios update

Last night, I attempted to update the bios on my P67A-C43 (B3) board using the version 5.1 bios. After the BIOS installed, it restarted and came up with the "all settings were reset to default values. press f1 to run setup. press f2 to continue" I hit f2 and my system keeps resetting in an infinite boot loop. I was able to reset the BIOS using the reset button on the back of the board to get back to the bios prompt, but pressing either f1 or f2 puts it back into the boot loop. Any help would be appreciated.

Quote from: ScunnyUK on 01-February-11, 16:08:59
Hi,
The blue screens started after a clean Bios flash to the 18b10 bios then eventually it stopped working complety (just doing the start up cycle over and over)
I had tried reseting cmos and it doesnt make a difference, the motherboard will not post , boot , start up at all so default settings cant be set (although reseting cmos would set to default anyway)
Each time the board goes through the start up cycle (i.e. upon pressing start button the board will start up with fans spinning for a second then shut down, start up again with fans spinning for a second then shut down, continuasly repeating until main power is removed) I have used a multimeter to measure the voltage read points on the board and they show that there is no vcore being suplied to the cpu but all other points show the voltage is being supplied to those componants, so imo that is where the problem lies and I would sugest that the other ppl who are having this issue to also try measuring the voltage read points and see if the same thing is happening on thier boards .
If others are getting the same results (no vcore) then the msi techs should be informed of this issue..(imo)
1.8b10 still is a beta bios. I got random bluescreens with that one also at some point a blinking bios led. So I flashed back from secondary bios (using the first option (change disable in enable)in "security" in the EFI shell to allow flashing from secondary bios), blinking bios led now stopped, Then I flashed with 1.7, no issues sofar cpu now running stable at 4.5Ghz (already 2 days).

MSI P67A-G45 (B3) boot/loop

Hi, just got all components for my pc and i installed everything. My problem is wheni press the power switch, everything starts fine and the fans spin up and the LED's on the board are fine but after 4-5sec it shuts itself off and tries the exact same process again. To troubleshoot i removed RAM, Video card, HD... just have CPU, cpu fan but still getting same issue..
Here is the list of the components i have..
Intel Core i5 2500K Quad Core Unlocked Processor LGA1155 3.3GHZ Sandy Bridge 6MB
MSI P67A-G45 (B3) P67 ATX LGA1155 DDR3 2PCI-E16 3PCI-E 2PCI SLI CrossFireX SATA3 USB3 Motherboard
G.SKILL Ripjaws X F3-12800CL9D-8GBXL 8GB 2X4GB DDR3-1600 CL9-9-9-24 Memory
Corsair Professional HX650W 650W ATX 12V 52A 24PIN ATX Modular Power Supply Active PFC 120MM Fan
Sapphire Radeon Xtreme HD 5830 800MHZ 1GB 4GHZ GDDR5 PCI-E DVI HDMI Mini DisplayPort Video Card
here is a video i found... its similar to my problem

Straight power loop? Can't even get to BIOS? if so could try resetting the CMOS, also try a different DIMM and/or GPU (even keyboard, had a couple post where the power loop ceased after unplugging the keyboard) and possibly best try a different higher powered PSU...if you can get into BIOS raising the vCore can help eliminate the loop problem, but still indicates something is wrong if it takes to much vCore for successful boot, with a 2500k should be able to boot and run stock at 1.19-1.21 for 3.3GHz

MSI P67A-GD65 infinite boot/loop problem

installed everything into my case and go to boot into the UEFI and nothing !
i press the power switch, everything starts fine and the fans spin up and the LED's on the board are fine, waits 5 secs then it shuts itself off and tries the exact same process again. it keeps doing this until i cut the power !
i've checked the 24pin etc, KB & mouse r fine, 2 different sets off RAM in every slot, cleared CMOS (i think).
seems like a very common problem with this board after a bit of googling !!
also tried
Quote
this is the 1st time ive used it !
tried the OC genie button on and off.
been sitting in the box unused for about 1.5 months. doubt that means anything tho.
put the stock cooler on securely, and still the same problem !
now tho, it wont start for about 3 secs after i press the power button
and
Quote
disconnected all the SATA's bar 1, and still the problem :/!
all the standoffs etc r fitted correctly and iv re-connected the 8 pin cpu and 24 pin. 1 stick off RAM in the 1st slot also :/!
checked no molex connectors r touching the case metal either
any suggestions?

motherboard: MSI P67A-GD65 (B3) bought on march 31st and used today for 1st time
CPU: intel core i7 2600K
CPU Cooler: tried an alpenfohn matterhorn with Scythe 1850RPM gentle typhoon Push/pull also tried the stock cooler
RAM Corsair CMD4GX3M2A1600C9 (2X2GB kit of 1600Mhz CL9 corsair dominator DDR3) and tried Patriot PSD34G1600KH (2X2GB kit of Patriot signature DDR3)
PSU Corsair TX650 650w psu
GPU XFX radeon 4870 1GB
Case NZXT M59 + mainly scythe fans and a noctua and coolermaster
DVDRW liteon DVDRW
Storage 128GB kinsgton SSDnow V100, 1TB Samsung F3 7200RPM, 1TB Hitachi 7K100 7200RPM all sata 3gb/s
Generic 5.25" fan controller
2 x 12" blue CCFL's
OS windows 7 x64 professional (installed on the SSD, but havent booted it yet as the board doesnt even get to BIOS :()
peripherals Microsoft reclusa keyboard and gigabyte GM-6990 (i think) mouse
monitor Benq g2222hdl connected via DVI
the only things i have changed today are, put the new notcua fan in my case, changed the Motherboard and CPU from and Asus M4A78LT-M & Athlon II X4 640 to MSI P67A-GD65 (b3) & intel core i7 2600k. Also, put the alpenfohn matterhorn on today.
everything is confirmed working apart from the CPU & Motherboard. everything worked yesterday, but i didnt have the necessary equipment to test the motherboard or cpu before using them together (today)
hope this will help

Boot Loop after BIOS reset

Some kids at the school I am stated at put passwords on the BIOS, so we used the pins next to the BIOS chip to reset the BIOS.
This has worked to clear the BIOS passwords, but it has had the unfortunate side-effect of putting any computer we do this to into an endless boot loop.
The computer gets as far as a screen where an option to "start windows normally" (among others) appears. Sometimes the windows xp logo can feintly and briefly be seen before the computer restarts its self.
I have re-created the issue with computers that didn't have passwords on the BIOS by resetting it anyway and the symptom persists.
What am I missing? I've tried using the BIOS options to optimize the setting and I've also take a compter that does boot (same make / model) and mantually copied over the settings in the BIOS.
Still can't get it to boot.
I can flat load linux to it, but windows won't take, either via a PXE boot or disk. The install seems to go so far as to unpacking the files, but isn't able to boot into windows sufficiently to do the rest of the install.
:s
Any help would be greatly appreceated as we now have 11 out of 24 computers doing this.

I would like to add, whilst I was using the pin clips on the pins near the bios chip, I let the system run until it would beep. During this time, the CPU fan ran really really hard. Have I damaged the CPU somehow?

HP Envy 6 - Boot Loop following Bios Update

Hi All,
Having spent the better half of tonight trying to resolve an issue whereby my HP Envy 6 1232SA was stuck in a loop after what I thought was a failed bios update.
I received a message saying an UPDATE for my bios was available. I installed the update using the SP available from the download site. The laptop started the reboot process, powered down and wouldn't come back up. I was getting the dreaded BLACK SCREEN that everyone is talking about.
I did all the ususal things that people here were advising. That being trying to load into zombie mode via the WINBUTTON + B, loading a recovery bios onto a bootable flash drive, using the HP UEFI TOOLS and such. None of this was working. It was clear that the laptop sounded as though it was constantly rebooting. You could hear the CD make a whirring noise for a second, stop, and retry.
When using the WINBUTTON + B I was getting a single flashing light on the caps lock screen. I had been informed that this meant that there was a CPU problem and that the machine would need to be sent back for repair.
I am a Desktop support technician with 20 years of experience. This would have been the first time I had heard of a bios update damaging the CPU.
I did a little more digging such as removing battery and cmos battery and trying to get laptop to power, this was also not working. What I tried next resolved the problem for me.....
I had installed a SSD into the machine. I removed the SSD and tried booting the machine with no HDD in the drive, the machine immediately powered on and completed the flash process. After the flash process the machine complained of no HDD (as I hadn't yet reinstalled it). After it was reinstalled, the PC booted fine into windows.
So to those who are having the Black Screen issue after a bios update, you could possibly try removing your HDD and booting the laptop with no HDD to see if that forces the flash to finish.
I have absolutely no idea why a bios update wouldn't work due to an SSD being in the drive, but meh..... This fixed the issue for me.
Hopefully this will help someone out.

@Alijc2014 ,
Hello and thank you for posting on the HP support forum. Here is a link to the HP blink and beep codes.
HP Notebook PCs - Troubleshooting LED Blink Codes or Beep Codes During Startup or Boot
Check this link and take a look at what your blink code is stating.
You may want to check this out as well.
BIOS Beep Codes
HP PC Hardware Diagnostics
Testing a Hard Disk from the BIOS
Let me know what you come up with.
Now if it comes down to a hardware issue you will have to deal with the country of purchase for repair options. If it was bought in the UK you will have to send it through to the UK repair system you will not be able to do this in the US.
Thank you again for posting and have a great day.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP

CMOS/Boot Problems after BIOS Update

I just used Live Update (two weeks ago) to update to all the latest utilities, drivers and BIOS on the following computer:
MSI 865PE Neo2-FIS2R
Pentium 4 2.4ghz / 800mhz / HT
512mb PC3200 (1 DIMM)
ATI Radeon 9600 128mb 8xAGP
Two WD 120GB/7200RPM ATA Harddrives - mirrored
FSP350-60PN Power Supply
Pinnacle PCTV PCI Card
Windows XP Pro - fully updated
The boot up screen now identifies BIOS as A6728 IMS V2.2 051904.
Since the update, the computer does not allow the operating systyem to shut it down - and the boot up process has been problematic (to say the least).
After the BIOS update, I set the BIOS settings to "performance defaults" - and everything seemed fine for awhile.
But then the boot up problems started - and I was once confronted with the message that "dram timing was too tight".
I reverted the bois settings to "default" - to no avail. The problems are continuing - and I am getting somewhat fearful that the system will not boot at all pretty soon.
After about 20 power on/off cycles where I got nothing but a blank screen, the system is now booted to a screen that is telling me that the CMOS settings are incorrect - and I have the options to run setup or load defaults and continue.
I know that I want to run setup, but what do I do to get this to stop happening?
Tahnks,
Bob99

As is usual, at least one mistake is made when building a PC. Rather than getting name-brand memory, in a moment of weakness, I ordered the generic stuff:
http://www.mwave.com/mwave/viewspec.hmx?scriteria=BA08583
I looked for documentation on RAM voltage, and found the MSI information on the MOBO product page:
Due to the High Performance Memory design, motherboards or system configurations may or may not operate smoothly at the JEDEC (Joint Electron Device Engineering Council) standard settings (BIOS Default on the motherboard) such as DDR voltage, memory speeds and memory timing. Please confirm and adjust your memory setting in the BIOS accordingly for better system stability.
Example: Kingston HyperX DDR500 PC4000 operates at 2.65V, 3-4-4-8, CL=3.
For more information about specification of high performance memory modules, please check with your Memory Manufactures for more details.
I also saw a couple of articles that said to be "very careful" with this setting as you can fry your memory. But I haven't found anything to help me learn about what the settings mean - or where I should start (2.65?).
Should I call Mwave and as them for the specs?
BTW - The computer is my son's - and he is moving back to college. I was giving it a tune up (driver's, etc.) - and noticed the ATI issue. Since I won't see it for 9-10 months and who knows what he will want to add to it, I thought it would be a good idea. I am a previous user of ASUS and my experience with them is that it takes about a year of BIOS updates to actually stabilize all the features.
Thanks for your help...
Bob

P35 platinum combo will not boot windows after bios update via Live Update

Hi,
I had everything running on windows 7 fine until 2 days ago. I installed Live Update from MSI website. I was about to install driver updates for my motherboard, but the bios update went instead. my pc tried to restart after the bios update installed, but it failed. would not post and would only see black screen.
then i removed one of my memory sticks. it would post, but then windows would not start up. it would get stuck at windows loading screen. i tried to reformat with my windows cd. but during install it would blue screen of death me. i tried multiple times and it would always blue screen of death with different errors. the last one i remember was a message saying i should off turn shadowing and caching.
this all started happening after i attempted bios update via Live Update.
Any help is greatly appreciated.
I have a core2quad 9450
this motherboard
MSI P35 Platinum Combo LGA 775 Intel P35 ATX Intel Motherboard
http://www.newegg.com/Product/Product.aspx?Item=N82E16813130141
this ram
G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1000 (PC2 8000) Dual Channel Kit Desktop Memory Model F2-8000CL5D-4GBPQ
http://www.newegg.com/Product/Product.aspx?Item=N82E16820231145
this harddrive
Mushkin Enhanced Chronos MKNSSDCR120GB 2.5" 120GB SATA III MLC Internal Solid State Drive (SSD)
http://www.newegg.com/Product/Product.aspx?Item=N82E16820226236
this video card
XFX PVT88PYSF4 GeForce 8800 GT 512MB
http://www.newegg.com/Product/Product.aspx?Item=N82E16814150280
Thanks!!!

at a guess you need to reset bios to ahci
a bios flash defaults to ide mode

Satellite A660 - USB boot problems after BIOS update

Hello,
I own a Toshiba Satellite A660 and recently have update the BIOS to the latest version (1.80). Since then the notebook will freeze on the boot screen (the one with the Toshiba logo) whenever a USB flash memory is attached.
It works without the flash memory connected and also if I connect it after I enter the boot menu or the BIOS setup. I can even boot from it like this.
As far as I am concerned this is a serious regression. Is there any way I can downgrade the BIOS version, or any other way to fix this issue ? I rely heavily on external USB drives.
Regards,
Claudiu.

I too am having problems with my A660 since upgrading to 1.80 bios - the HDD/SD utility, the pc health monitor and half the other toshiba utilities no longer work because they can't recognize the bios and actually tell me this... I get an error message telling me ''can't get bios type''...
On top of this I get the boot problem as well - I have to unplug half of my USB devices to get the laptop to boot properly...
And now - one month into owning my new A660 - after a hard drive failure, a problem with the Broadcom internal wireless adaptor I now have the internal TV tuner no longer working and have no idea how to fix it...
My gut feeling is that the sooner I can downgrade to the original factory bios the BETTER - and wait for another bios update to come along that is not faulty/buggy...
HOPE someone can help me with this...
John.

Troubles in dual boot system after BIOS update

Hello:
PC: Thinkpad T500
1. I had for one year Linux Fedora 10 and Vista Ultimate working in dual boot with Grub, no problems at all.
Three days ago Lenovo support recommended I update my BIOS from 2.07 to 3.12, as I had some intermitent Sleep problems in Vista. Then my problems started.
2. First, after updating the BIOS from Vista (dowloaded the exe, double clicked it, gone through the whole sequence with no errors), upon the first restart, the screen was black and I couldn't get in BIOS with F1 and the same happened during other power-off/power on sequences.
3. Now, I've discovered that the best I can do is wait for 10 min after restart in order to get a prompt from ThinkVantage, then Grub boots only the Linux system which works OK.
4. I can't get the dual boot message from Grub, and I can't get any Windows DVD to be taken at boot (I've got full backups from both Control Panel and from ThinkAdvantage backup facility) in order to ru Windows repair.
5. I can go during the ThinkAdvantage to BIOS, the new version seems there (not sure if completely operational), but whey can't I see it with F1?
Is the presence of ThinkAdvantage something special in dual-boot systems or wrt to the BIOS install? Should I do something special about it? I just don't know.
Any ideas?

Strange. I don't have a clue, but I have seen posts here that recoverd from strangeness after a BIOS update by unplugging from the AC mains, removing the battery, and then pressing the power button several times. The last time, hold the button for 10 seconds or so.
That is really a total WAG, but maybe worth a try.
Out of curiousity, what do you see when grub finally loads. I take it that it isn't your original boot menu. Do you have grub installed in the MBR, the boot sector of the Linux partition, or both? Is the Linux partition (or Linux boot partition if you have boot + root) the 1st one on the drive, or _after_ the vista partition.
[edit] You didn't ask, but IMNSHO multibooting a modern laptop isn't really the easiest way to run multiple OSs. I run Linux, Solaris, and OS X in VMs under Win 7 on my T400. They run well, and that approach avoids issues like you are having. The Lenovo ThinkVantage boot-time stuff and R&R are rather fragile. Changes in partitioning and MBR configuration can break them. BIOS and other updates, and Windows repairs can break the multi-boot setup.
There are several ways to set up VMs, but VMWare Player is what I use. The latest version is free and quite usable.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Boot issues after bios update (U430 touch)

Hi all,
I've been having some problems after updating my BIOS on my Ideapad U430 touch. After updating 7CCN34WW to 7CCN35WW, Windows 7 would not boot. It shows the usual 4 colors swirling to the center and then it stalls. Interestingly enough, at the top of the screen, white dotted lines appear (about 1 cm thick). These dotted lines alternate, turning off and on irregularely. I've waiting at least a half an hour, nothing happens.
Now I figured out how to solve this, which is by changing the boot settings in the bios to Legacy instead of UEFI. After changing it back to UEFI everything works again. But every other day or so it still hangs during UEFI and I have to change the bios settings back and forth to get into Windows. Can anyone enlighten me on this issue? It would seem the bios update is faulty? What's going on? Can I downgrade the bios?
In addition, the following topics are related but not quite the same as they don't describe the exact problem I have.
http://forums.lenovo.com/t5/IdeaPad-Y-U-V-Z-and-P-series/Bios-Update-flash-error-U430-Touch/m-p/1591...
http://forums.lenovo.com/t5/IdeaPad-Y-U-V-Z-and-P-series/P580-BIOS-update-Cant-start-up-computer/m-p...
Thanks in advance,
Cheers,
Graham

hi gannixon,
Welcome to Lenovo Community Forums!
Yes it is possible that a UEFI / Secureboot check fails something in the OS UEFI boot after the update.
The system does not support a backflash feature, Reflashing the BIOS might need to be done in Lenovo Service Depot,
If you don't have much data on the unit, I can suggest performing a one key Recovery while on a UEFI mode.
Downside will be Deletion of current files and documents and back up will be required.
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

DROID in boot loop after OTA update

Just accepted the update today. After phone updated and attempted to reboot...its in a continuous boot loop. How can I stop it?

Try taking the battery out. If it still loops when you try to power it on, then the only other thing to try besides a factory reset is to take it to a verizon store and see if they can do anything.

P67A-G45 Fan Control Problem After BIOS Update

My old BIOS version was 1.8. I could control my fans in BIOS(50-75-100% RPM). Also SpeedFan tool was working perfectly, I could change fan speeds freely.
I just installed MSI Live Update and tool updated my BIOS version to 1.E(CPU-Z says v1.14) without any problem. But when I entered BIOS/Hardware Monitor I saw that fan control is disabled. Both sys fan 1 and sys fan 2 are stuck in %65. SpeedFan doesn't working too.
CPU Smart Fan is okay, works fine but system fans are uncontrollable now.
My Hardware;
i5 2500k
MSI P67A-G45
G-Skill 1333MHz 2x2GB DDR3
Samsung 502HJ
HAF 912+ with 2x120mm fans 2x200mm fans
Sapphire Pure 625W

Flash back to the BIOS that worked for you and report your findings to MSI technical. >>How to contact MSI.<<
Use the forum flasher in the future. Its safer. >>Use the MSI HQ Forum USB flasher<<

T420s Boot problem after BIOS update

I updated T420s from 1.37 to 1.38 while laptop was in the dock, not connected directly to power. Now it starts to boot then goes to a black screen and hangs. If I use f11 to boot from a CD, then it boots normally to Windows 7 Pro and works fine. I also notice the power indicator no longer lights, it only flashes a couple times then stays dark.
I still had 1.36 in my drivers so I tried going back to 1.36 BIOS, hooked to power this time, not dock. That worked and it shows 1.36 version as the BIOS but boot behavior is the same. Any ideas?
Moderator Note; subject edited; system type added

Hi,
Welcome to Lenovo Community Forums!
I'm really sorry to hear that your Lenovo T420s does not boot properly after a BIOS update.
I would suggest you to disable Intel AMT in BIOS and set the security chip, TPM, as active in BIOS and check if the system boot properly.
Occasionally, a system BIOS flash procedure will not execute properly and a system may be hung in a black screen state. If the system not booting properly, it can often be recovered by clearing CMOS.
Remove AC and System battery.
Press and hold the power button several times (3-5 time) for a count of 5 seconds
Reconnect AC and press the power button - if system starts normally, shut down and insert the battery
Remove the CMOS battery, and allow system to set for 30 minutes.
Location of CMOS battery and instructions for removal can be found in the hardware maintenance manual.
Try updating your docking station firmware as well.
Do post back if issue persists after performing the above troubleshooting steps.
Best regards,
Mithun.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

MSI P67A-GD53 (B3) Boot loop after BIOS update

Similar Messages

Maybe you are looking for