Msi p67a gd65 bios 1.6 dont save

i the bios 1.4 work but if i update the bios whit new release 1.6 when save and exit dont save reset to default
i face cmos but dont save only whit 1.4

Quote from: Svet on 12-January-11, 06:19:39
By USB method you mean you used the ==> >>Use the MSI HQ Forum USB flasher<<
or something else?
Hi Svet, yes - I used the MSI HQ Forum USB flasher.. along with all of the instructions given in the guides, including clearing the CMOS afterwards.
When I go back to 1.4, everything works again. I get the save issue in both 1.6 and 1.7b4 - the mouse freezes and the computer just sits there until hard reset.
I want 1.7b4 for the pll overvolt fix.. at the moment I can't get past 4.2 ghz with i7-2600k and a high perf noctua cooler, fairly sure it is not the cpu/temp/volts holding me back.
I also have a very strange issue in the bios is reporting my CPU as running at 20 GHz (which it clearly isn't) - although windows cpuz reports the correct speed. A very similar issue for my DRAM speeds, they are also reported as being something extremely high in the bios but are correct in cpuz.
There is also an issue with turning off spread spectrum in 1.6/1.7 - when I do this, the bios hangs (same way as it hangs when trying to save in 1.6/1.7, mouse freezes and have to hard reset).
In short quite a number of issues here.

Similar Messages

  • MSI p67a-gd65 dead after last bios update 4.0

    hi, i read and execute exactly the bios update ver. 4.0  for MSI p67a-gd65, oll goes ok, update bios and ME successful , but after restart ... main board dead!!! i prove reset cmos  ... nothing ....  mainboard starts and work only 1 second, after that restart in an infinite loop with work 1 second and restart, i must disconnnect the power cable to stop that infinite reset!!
    mainboard damage? 

    Quote from: Differentone on 02-June-12, 20:30:48
    I think you failed at disconnect the power while in loop.
    Because of was the same as me, infinite loop like 4~5 times and after continued to install.
    Here for an explanation look at page 4 > http://event.msi.com/mb/22nm/Bios_ME7_to%20_ME8_update_SOP_EN.pdf
    If you didnt seen this part, failed and.... I dont know what can you do at this point.
    in fact the problem was after this last update mentioned on page 4 of SOP guide that you linked and that i was read ... all ... but what is strange is that i have no display error during all update .. alla goes fine ...after last reboot  ... dead.
    someone can tell us what's happened? i'm not newbie about this procedures of bios update ...without any problem.

  • Problem with downgrading bios. MSI P67A-GD65 (B3).

    Hi!
    I'm having problems with downgrading my bios from version 4.3 to 1.19. I want to downgrade, because 4.3 doesn't want to boot when I use xmp settings for my RAM ( that might be related to my CPU since I have i5 2500k which is 32nm and 4.3 version of BIOS is recommended for 22nm processors ). When I try to flash with the MSI Forum HQ USB Flashing Tool I'm getting an error: "Rom file ROMID is not compatible with existing BIOS ROMID". I've ran out of ideas how to downgrade my bios so I'm asking you for help. My specs:
    MOBO: MSI P67A-GD65 (B3)
    CPU: INTEL CORE i5 2500K
    RAM: G.SKILL RIPJAWS X 4GB (2x2GB) DDR3 1600MHZ CL6 (F3-12800CL6D-4GBXH)

    Here you go. GD65 and GD55 usde the same BIOS files;
    https://forum-en.msi.com/index.php?topic=179837.msg1295420#msg1295420

  • BIOS 4.3 half flashed on MSI P67A-GD65 reboot loop ME not installed

    Hi, yesterday I tried to flash my bios from 1.19 (1.jo) to 4.3 and I followed the SOP guidelines. Made a flash fat32 got bios on it, started it, stopped all my applications under windows and it went with no error. PC Restarted and now it's in infinite reboot loop. The moment the MSI BIOS logo appears, the PC auto reboots.
    If I remove the usb drive or replace the bios file with another version it tells me it's not the file it needs. When I insert the one with the .43 file it goes back to reboot cycle. I tried resetting the CMOS with the button on the mainboard and I have this screen telling me BIOS is 4.3 and it has recognized all my 12gb ram, 2 hard drives and processor. Then it has press F1 to enter setup and press F2 to continue, both options result in reboot.
    I tried the 1.JO on flash, but it tells me again that it's the wrong file. Tried renaming it to amiboot as I found somewhere, but to no avail. Tried renaming the .43 to EIVB.bin as it was suggested in one forum, again no luck.
    System specs:
    OS: Windows 7 64bit
    Mainboard: MSI P67A-GD65 (not B3)
    CPU: Intel Sandy bridge i5-2500k @3.3ghz
    RAM: 2x2gb Kinston 2x4gb Gskill DDR3@1333hz 10600 CL7
    GPU: Nvidia Gigabyte G1 Gaming GTX 970 (reason I wanted to flash bios)
    PSU: Seasonic 80+ platinum 650W
    HDD: WD Caviar Green 2GB
    SSD: Corsair 60gb
    DVD: Liteon burner

    Quote from: Svet on 22-February-15, 19:25:45
    older non B3 versions ME can't be flashed,
    therefor you will brick it if you attempt to do it via MSI's all in one updater..
    you can try anyway to try with barabone setup with 1 memory stick only and disconnect everything that's not required to boot
    and to try the USB key in any of the other USB ports
    and/or with different USB key too
    to see if ME update will able to continue
    I wasn't sure about the ME update, read that someone managed. The Live Update 6 did my 1.19 (1.JO) update. I tried all usb slots and 3 different sticks, formated them and so on. Nothing worked. I tried disconnecting all hard drives and DVD drive too.
    Is there a way to stop this cycle or to restore to the 1.19 version?

  • Msi p67a gd65 with p67a gd80 beta bios

    hi to everyone here,
    i have purchased a pc and have a msi p67a gd65 mobo
    i noticed that on the actual mobo it clearly states its a p67a gd65 i have verified this , its defnately a gd65
    how ever, cpu z detects it as a p67a gd80, also command centre detects a p67a gd80, bios version is : P67A GD80 10.3b2
    so my mobo has a gd80 beta bios...
    i do not know how it came about as im not owner from new
     question 1 : all i need help with is flashing back to gd65 bios (bios  1.19 ]  , do i need to do a blind flash to force update ? and how do i do it ? because its gd65 not gd80
    question 2 : and also how do i check if both bios chips were flashed to this beta bios ?
    question 3 : do i flash both bios chips when i do the bios flash ?
    question 4 : how do i switch between the 2 bios chips ?
    sorry for all the questions, the main question is question 1
    thnx guys

    Quote from: PirateDog on 17-November-13, 03:50:12
    In my experience, for a 2700k, UEFI/BIOS v1.H proved to be the very best one.
     I would go ahead and use what P D says there, he did a lot of testing on his many builds the past few years and knows more about it that most other people.
     What I had in my last reply was just the basic required info you needed to answer question about 2700K support after going through 1/2 dozen lists needed to find my info.

  • Msi P67A-GD65 keep restarting after bios update

    Hello
    I  have a Msi P67A-GD65 B2 motherboard, I tried today to upgrade bios to version 4.2,after update pc start up showing marvel controller then MSI logo and then computer restart over and over,if I try to enter BIOS will show 'entering setup', and restart again.Dual BIOS led does not light up and is not blinking.What can I do in this situation? How to switch the motherboard BIOS to boot from the other one?

    Quote
    Can you verify that, I don't think they make a B2.
      Not sure why the hijack in this thread with different hardware involved, but a B2 is a defective mainboard from the beginning, and should have been replaced at the time of the replacement offers over a year or so ago.
    Quote
    I understood that there was a backup BIOS so I felt confident to be able to fall back in some way. Can you help me using that backup?
    The Ivy udpate flashes the secondary chip as well on the GD65, so it would do no good to have access to it unless you could get into the UEFI/BIOS somehow to 'enable' the Dual BIOS Auto Update setting to restore the corrupted primary.

  • HELP! My 2011 MSI P67A-GD65 (B3) build suddenly refuses to boot

    Hello, I am new to this forum because I hadn't had any troubles yet.
    I built my system in July/August 2011. Here's what it has:
    MSI P67A-GD65 (B3)
    Intel Core i7-2600K Sandy Bridge CPU
    16GB Corsair Vengeance 240-pin DDR3 1600
    650w Corsair Enthusiast PSU
    MSI N460GTX Cyclone 1GD5/OC GeForce Graphics Card
    1x 2TB Hitachi 7K3000 7200RPM SATA 6 GB/s (With Windows 7 64-bit installed)
    2x 3TB Seagate 7200RPM SATA 6 GB/s (For storage)
    I have used this computer for graphics and video editing...it has served me faithfully. Yesterday evening while editing a Word document, I got "do you want to save your changes before exiting?" and of course I said yes. Then to my surprise my computer proceeded to shut down and reboot. At first I thought maybe I missed a Windows Update message telling me it would reboot in xxx minutes so I was not alarmed. But then as I watched it reboot, it gave me the POST message that there was no disc drive recognized. I thought that was weird since I never noticed it before. But then after the BIOS screen with the MSI graphics thing I was faced with a blank screen except for a flashing cursor two inches from the top of the screen. When I realized that this wasn't going to leave, I got a bit worried so I did a reset through my tower's button and same thing happened...I unplugged everything and let it sit for a few minutes... restarted 10 minutes later....same thing. Did it again and then went into my BIOS to look around. It showed no HDD's connected and I had 3 hooked up. I was concerned my HDD went bad so I connected it to another pc and accessed it with no trouble as another storage...I was happy my files are all there. So then I reconnected to my original build and got the same POST message, but this time the drives were visible in BIOS....but still no boot.
    I have another blank SATA HDD so I removed all my HDD's and connected it by itself along with my SATA DVD drive and I tried to do a clean Win7 install on it. But at the point in the install process where it asks WHERE you want to install Windows, no drives showed up. So that door was closed. I tried the same thing again after swapping SATA port locations, thinking 1 was defective, but I got the same treatment from all of them...nothing recognized during the install process, although the drives are showing up in BIOS....
    I think I know why the POST message is saying 'no drives detected,' though...I read it is saying that based on the SATA ports being used...I have 8 SATA's on my MOBO...4 6gb/s; 4 3gb/s. 7-8 are 6gb/s and ONLY when I have a HDD plugged into one of them does it show on the POST screen...which I still think is weird, and seems to have just started happening last night with the rest of the problems...but I could live with that since I could disable the message in BIOS I think.
    But I have tried to clear the CMOS...all three ways...jumper, button, battery. I reset BIOS thru BIOS.... Nothing changes. BTW, in BIOS I ran a RAM memory check and it passed. Besides, I am not hearing any weird beeps...related to that....
    I don't know why this would happen after working perfectly for 2 years... And why would it politely shut down in the beginning of the process anyways? I mean...I appreciated being asked to save my changes...but I don't know what else to do...PLEASE OFFER SUGGESTIONS...any help is appreciated.
    Thank you in advance...I hope someone can help me! I am still covered by warranty...but I want to do this right.
    Thanks!
    Marie
    EDIT: BTW, I have also tried unplugging everything from the pc except for the DVI and power plug in case that was interferring....

    Quote
    On a slightly different topic...would it work (I have never done this!) to take my OS HDD and boot it on another PC? I am thinking this would not work because of system files and etc., but I have always wondered this and now would be the best time for me to know
    It mostly works if the components used aren't too special. As you have no RAID setup it should work. However you will need to reactivate Windows once it made it. Of course you will also need all drivers for the new machine. Be aware that you might not be able to connect to the internet before you installed the proper driver for the ethernet adapter.

  • P67A-GD65 bios?

    Hi,
    On the product page i see 1.6 as the latest? but even this goes to a broken link?
    Where is everyone getting other bios updates from? and are they stable?
    Thanks!

    i bought a pre overclocked bundle with the below spec....with default settings i can install windows with a raid config...no sweat.
    If i try OC genie(at 4.2ghz) i can get into windows fine...but 10 minutes into black ops and it blue screens.
    with the OC profile provided by overclockers(4.6ghz) i can even boot into windows...it seems to struggle to recognize my raid config. i just get "machine check error" or a blinking cursor...sometimes it goes to shell command prompt.
    each time i change the OC settings....i make sure raid is reselected and my boot options are reselected.....1/ HD 2/dvd.
    ive been chatting with overclockers for a week now...and they seem to keep recommending the same things....then suggest trying a different drive setup. Which im confused by...i dont see the point in trying with IDE or AHCI....if ultimatly im aiming for raid 0 config??
    I'm totally lost:(
    ...oh!!! thanks for the responses!!
    ...also! i cant update bios from 1.4 at mo...as itll invalidate my warranty.
    spec:-
    - CPU: Intel Core i7 2600K 3.40GHz @ 4.60GHz Sandybridge CPU
    - Motherboard: MSI P67A-GD65 Intel P67 (Socket 1155) DDR3 Motherboard
    - RAM: Corsair XMS3 4GB (2x2GB) DDR3 PC3-12800C9 1600MHz Dual Channel
    - Cooler: Corsair A50 CPU Cooler
    - Artic Silver 5 Thermal Compound
    im using an OCZ 600w psu and drive setup of ...640GB (320GBx2) SATA-II 3.0Gb/s 16MB Cache 7200RPM HDD

  • MSI P67A GD65 System Freezes while Gaming

    hey
    i m facing system hangs/freezes while gaming. it is all along working fine but suddenly problem arrises outta nowhere.  mostly happens in Metro Last Light Game.  i did change multiple things like 2 different rams stick, Bios are 4.1v (at default), i tried 2 different GPUs like 290 and 580 but stilll facing same issue. dont know why.
    if you can help on it this, it would be alot appreciated.
    m PC
    MSI p67a GD65
    I5 2500K
    8GB RAM
    800w PSU

    What is the actual power supply?
    Follow this >>Posting Guide<<
    Make sure you run latest BIOS.
    PS: Intel ME driver is crucial, without it system won't work properly, and that's why it didn't freeze anymore. Same applies to GPUs: if you have 400W power supply and want to run 2-way SLI, it will be fine until you install drivers, which make the computer and graphic cards recognise how much power they have and so on

  • MSI P67A-GD65 infinite boot/loop problem

    installed everything into my case and go to boot into the UEFI and nothing !
    i press the power switch, everything starts fine and the fans spin up and the LED's on the board are fine, waits 5 secs then it shuts itself off and tries the exact same process again. it keeps doing this until i cut the power !
    i've checked the 24pin etc, KB & mouse r fine, 2 different sets off RAM in every slot, cleared CMOS (i think).
    seems like a very common problem with this board after a bit of googling !!
    also tried
    Quote
    this is the 1st time ive used it !
    tried the OC genie button on and off.
    been sitting in the box unused for about 1.5 months. doubt that means anything tho.
    put the stock cooler on securely, and still the same problem !
    now tho, it wont start for about 3 secs after i press the power button
    and
    Quote
    disconnected all the SATA's bar 1, and still the problem :/!
    all the standoffs etc r fitted correctly and iv re-connected the 8 pin cpu and 24 pin. 1 stick off RAM in the 1st slot also :/!
    checked no molex connectors r touching the case metal either
    any suggestions?

    motherboard: MSI P67A-GD65 (B3) bought on march 31st and used today for 1st time
    CPU: intel core i7 2600K
    CPU Cooler: tried an alpenfohn matterhorn with Scythe 1850RPM gentle typhoon Push/pull also tried the stock cooler
    RAM Corsair CMD4GX3M2A1600C9 (2X2GB kit of 1600Mhz CL9 corsair dominator DDR3) and tried Patriot PSD34G1600KH (2X2GB kit of Patriot signature DDR3)
    PSU Corsair TX650 650w psu
    GPU XFX radeon 4870 1GB
    Case NZXT M59 + mainly scythe fans and a noctua and coolermaster
    DVDRW liteon DVDRW
    Storage 128GB kinsgton SSDnow V100, 1TB Samsung F3 7200RPM, 1TB Hitachi 7K100 7200RPM all sata 3gb/s
    Generic 5.25" fan controller
    2 x 12" blue CCFL's
    OS windows 7 x64 professional (installed on the SSD, but havent booted it yet as the board doesnt even get to BIOS :()
    peripherals Microsoft reclusa keyboard and gigabyte GM-6990 (i think) mouse
    monitor Benq g2222hdl connected via DVI
    the only things i have changed today are, put the new notcua fan in my case, changed the Motherboard and CPU from and Asus M4A78LT-M & Athlon II X4 640 to MSI P67A-GD65 (b3) & intel core i7 2600k. Also, put the alpenfohn matterhorn on today.
    everything is confirmed working apart from the CPU & Motherboard. everything worked yesterday, but i didnt have the necessary equipment to test the motherboard or cpu before using them together (today)
    hope this will help

  • MSI P67A-GD65 and other 1155's whine

    Hello MSI and community.
    Recently I decided to build a PC especally for minimun noise.
    I waited a long time for the B3 boards so I wouldn't have to go through the trouble of returns. Sadly this didn't work out.
    First of all I ordered the cheapest and first mobo(gigabyte ph67-ud-b3) that was relesed. Soon as I plugged it in and Windows 7 got to boot screen (from the DVD) it started giving off a high pitched whine.
    After alot of research I RMA it and ordered a Asus P8H67-M LX. Loaded it up and thought woohoo no whine, then as soon as windows finishes installing the drivers (first time on windows) of goes the whine again.
    I RMA that 1 too and bought the MSI P67A-GD65 advertized as "whistle free" as well as people on another forum saying they didn't hear anything from theirs. This one does the same but I can't keep sending back boards for RMA and want to keep this one so I'm here hoping to try and resolve the issue with MSI.
    I have tested these boards with Casecom 500w, ozc gamextream 700w, antec true power 650w and coolermaster pro m 600w with them behind a door to eliminate any fan noise.
    MSI GPUS: 8800GS, 8800GTX and 560TI as well as onboard from the h67 board.
    I've tried many differant BIOS settings, nothing but disabling C-STATE (fully disabled) effected it. (I havn't manually played with volts)
    On the other 2 boards I noticed it seemed to dim when I unplugged all USB devices and in their BIOS it was c3/c6 I had to disable, MSI board doesn't whine as loud as the other 2 but it's more constant but with a morse code type theme to it which seems to be coming from CPU socket whenever the PC is idle, it's equally noisy from either side of the board. It's very annoying and accually gives me a headache as maxium distance.   
    Alot of people have said their 1155 board don't make a sound but 3/3 for me have so I'm not sure what to think.
    I'm currently running with c-state disabled but Turbobooster only seems to go to 25% and slower clock speed on my i5-2500k and I assume for power usage, all things I don't want.
    Can you give any information at all? Might it be possible to correct with a BIOS update? I'm open to any suggestions and will keep checking back here.
    Hope you will be able to work with me on this issue.
    Thank you in advance, I've prefered to go with MSI all my computering life.
    Paul

    Quote from: HU16E on 22-March-11, 04:18:14
    Used the same CPU cooler on all three? That would be my wild guess.
    I test it fanless of course  but no I have used mutiple heat sinks aswell.
    Quote
    What's wrong with throttling down at idle or low usage? Who sits at a stop light with the engine at full throttle?
    I'm not too sure what disabling C-state accually does but when running Orthos I saw speed was at 3.6ghz instead of the 3.3 while disabled.
    Quote
    Contact MSI Tech Support by opening a ticket & ask them. This is a user to user forum, being as such, MSI will most likely never read your thread.
    Thanks, I didn't realize that.

  • MSI P67A-GD65 keeps turing on and off...

    I have had the follwing build since about march this year.
    8GB Mushkin Silverline #996770 (2x4GB) DDR3 1333MHz 9-9-9-24
    MSI P67A-GD65 Intel P67 (REV B3) Socket 1155 DDR3 PCI-Express Motherboard
    Intel Core i7-2600 3.40GHz (Sandybridge) Socket LGA1155 Processor - Retail
    XFX ATI Radeon HD5750
    It was all working reasonably fine but I had notice it getting abit noisier so thought it was time for a bit of a clean to remove dust from fans, heatsinks etc. which it drastcially needed.
    Anyhow, put it back together and now it turns on and off on start up at a period of about 5 seconds. (It has done this about 11 time before I unplugged it) Checked connections but everything SEEMS fine there. Unsure what it could be and could do to get it back up ASAP.
    All was working fine prior and upto cleaning (which was today).
    Also I currently have no computers to test bits on but I have done a Bare bones test with no look.
    I am secrectly hoping one of  can tell me its the heastink as I do have another of those (in fact a better one which I should really put on) but I somehow doubt it would be the issue.
    Anyhow I hope this is enough information but I will promptly reply as soon as I can if you need to know anything else.
    Thanks,

    If it does not POST should it go I still get some output to the screen? I remember many years ago I could get to the BIOS but not boot with no RAM in. Should this happen with this board?  All I would like to do is eliminate as many components as possible.
    I am not sure sucessfully POST ing is necessarily important in this instance as the issue is (to me)a little odd. Even if it does not POST should it stay on for more than a second and secondly if it does turn off should it stay off and turn on and off ad infinitum? Just to not I am not using the case power switch just in case this had for whatever reason got jammed (this has happened on a computer I had to fix once (I am not a professional but often get roped in to "can you just have a quick look at..."))
    Once again a huge thanks for the continued support on this, I have had far more useful advice/questions asked so far from you than I have from MSI themselves and actually had responses unlike my retailer (I will have ot try call them tommorow).

  • MSI P67A-GD65 Slow Boot

    At times I'll get stuck at B4 or 98 error code for a good 5-15mins plus. I will either have to wait it out or press reset until it boot properly. Even when it gets passed this issue I still have to wait a while looking at the windows start up animation. I'm using a 2500k right now, my i920 system only displays the animation once before proceeding into windows.
    The major issue is the B4/98 issue. I have tried a lot of things to no availability. If all else fails I will send this board back to Amazon and pick up an Asus or w/e.
    Thanks,
    MSI P67A-GD65
    2500K
    ASUS 550 ti
    8gb corsair vengance
    crucial m4 64gb 0009
    corsair hx520
    usb card header card reader
    sony dvd/rw sata
    windows 7 pro 64

    Quote
    At times I'll get stuck at B4 or 98 error code for a good 5-15mins plus.
    Quote
    Is the B4 error just a generic
    http://www.xannex.co.kr/doc/ami_aptio_4.x_status_codes_pub.pdf
    98 = Console input devices connect
    B4 = USB hot plug
    What other USB devices besides the "usb card header card reader" and the mentioned mouse/keyboard combination do you have connected to your system?
    Can you please try without the card reader?
    Quote
    It's a B3 with the latest bios.
    The latest Final UEFI/BIOS Release (E7681IMS.1E0) or the latest BETA Release (E7681IMS.1F5)?

  • Will updating my P67A-GD65 BIOS delete my OC profiles?

    basically, as the title says.
    if I flash the BIOS on my MSI P67A-GD65, will it delete all of the OC profiles? or will all of the previous settings be kept?
    also, what is the best, stable BIOS to date?
    I'm tired of the irritating RAM issues with the older BIOS I'm using so I've decided enough is enough and I'm going to update it, provided my OC profiles and settings won't be deleted.
    thanks.

    Quote from: lucas4 on 09-November-11, 06:11:49
    basically, as the title says.
    if I flash the BIOS on my MSI P67A-GD65, will it delete all of the OC profiles? or will all of the previous settings be kept?
    also, what is the best, stable BIOS to date?
    I'm tired of the irritating RAM issues with the older BIOS I'm using so I've decided enough is enough and I'm going to update it, provided my OC profiles and settings won't be deleted.
    thanks.
    Previous settings are maintained, but only guaranteed to work with your previous BIOS so use on a new version at your own risk as may cause unexpected results.
    I do find this useful though as you can refer back to previous settings when duplicating for the new BIOS settings.
    Don't forget to clear the CMOS whenever updating the BIOS too before applying new settings.
    Best stable BIOS is the subject of much discussion. 1C was the last one that allowed O/C over 4.9GHz, 1FB5 was the last one that supported my config with an OCZ Revo as boot device (at less than 4.9GHz). 1E was the first one that supported my RAM @2133MHz out of the box....

  • P67a-GD65/BIOS 1.7 Windows is good loading only after reboot

    Hi, I have a trouble with a P67a-GD65(BIOS 1.7)
    When I start PC (With Keyboard Razer tarantula plugged) motherboard have this signal: http://rghost.ru/4210405
    Without keyboard: http://rghost.ru/4210504
    Maybe this is normally signals, but:
    When I turn off my pc at night, windows dont loading with the first time
    After POST I have black screen with blinking underscore - after reboot, windows loading is good. The same way is good loading, when I reboot PC from Windows, or turn off my pc for 10 minutes and turn on.
    In first time Windows loading is normally, but after log in screen i had windows message about new SATA device and searching drivers for it, then BSOD: Quote
    SYSTEM_THREAD_EXCEPTION_NOT_HANDLED 0x1000007e
    Dumps - http://rghost.ru/4210562
    In BIOS SATA mode is IDE
    HDD without BAD sectors
    Configuration:
    Quote
    Operating System   Microsoft Windows 7 Ultimate 6.1.7600 (Win7 RTM)  
    Computer Type   ACPI x64-based PC  
      Motherboard:  
       CPU Type   QuadCore Intel Core i7 2600, 3500 MHz (35 x 100)  
       Motherboard Chipset   Intel Cougar Point P67, Intel Sandy Bridge  
       System Memory   4080 MB (DDR3-1333 DDR3 SDRAM)  
       DIMM1: Kingston 9905403-171.A00LF   2 GB DDR3-1333 DDR3 SDRAM (8-8-8-22 @ 609 MHz) (7-7-7-20 @ 533 MHz) (6-6-6-17 @ 457 MHz)  
       DIMM3: Kingston 9905403-171.A00LF   2 GB DDR3-1333 DDR3 SDRAM (8-8-8-22 @ 609 MHz) (7-7-7-20 @ 533 MHz) (6-6-6-17 @ 457 MHz)  
       Video Adapter   NVIDIA GeForce GTX 460 (1024 MB)  
       Disk Drive   ST3160815AS ATA Device (160 GB, 7200 RPM, SATA-II)  
       Disk Drive   ST3400632NS ATA Device (400 GB, 7200 RPM, SATA)
    Code: [Select]
    Sorry for my english, and please help 

    All time i use only white sata ports for HDD and 1 black for CDROM
    Some screens:
    Im try for disable EUP 2013 in BIOS Results will be tommorow
    Quote
    see if that cures it
    Now I dont get this message in windows (it was at the first time, as far as I can remember windows had loading without reboots)

Maybe you are looking for