MSI P6N SLI PLATINIUM problem with ram 800MHz

Hello.
I have problem with ram frequency.
I have MSI P6N SLI PLATINIUM and OCZ 2x2GB 800MHz CL5 but in bios I see that my ram runs in 667 MHz. Because I have 800MHz ram, so it shouldn't be default 800MHz and not 667MHz? What I have to do to show bios that I have 800MHz ram?

Quote from: DaLoona
Oke, but they told me when i bought my new system that XP auto adjusts the speed of the memory.
XP 64 bit can works normally with 4 or more GB they said, just like vista.
Just typing what "the professional's" at the store said.

Similar Messages

MSI P6N SLI sound problem under windows 7

Hi all!
I have an MSI P6N SLI mainboard and I have installed win7 ultimate x64 to get a look on that OS. Everything works fine expect one thing: I have no sound. I tried to install manually the realtek sound driver but no changes. When I check the Volume Control Options then neither the Speakers nor the Realtek Digital Output checked (but the speaker is plugged in).
However I have sound under Linux.
Could someone help me? (and sorry if I have missed the topic which resolves this problem if there is any)

Hi everyone,
hope it's ok to refresh this thread - I did not want to open up a new one, because this one matches my problem perfectly - but my speakers are plugged-in the right way
I'm running Win7 64 on the MSI P6N SLI (not v2 no Platinum) and am unable to install the sounddriver (well not correct - I did install the driver). The upgrade advisor said all green (under Win XP 32) and the MSI-Driver-Page propagates Win7 32/64 is supported for the SoundCard of my Board.
The driver installs just fine, but the device won't come out of "I have a problem"-state - always telling me "The drivers for this device are not installed. (Code 28)" (I event tried installing the driver manually with pointing the win-hardware-setup-routine to the driver-directory) - still no use - I removed and rebootet serveral times...
Hope anybody has a solution for this problem (I'm taking the posts above as a "this has to work"-basis so i'm not ready to give up and go out there and buy a new soundcard )
Thanks in advance for any hint.

MSI P6N SLI 4gb problem closed??

Hi, All.
MSI P6N SLI 4gb LOW Performance problem closed??
Thanks

There´s a large thread about the 4GB problem, don´t know why you didn´t found it.
And YES the problems are gone.
From bios version 2.13 for sli and version 1.22new for sli platinum everything works well.
There are 4x1GB Crucials in my system and they are running without any problems now.

P6N SLI V2 problem with "dual core center"

I have the P6N SLI V2 with E4400 and 7600gt running XP pro sp 2.
after installing and running MSI's "dual core center" (including .Net framework) I only have the "VGA" option enabled, the "MB" option is disabled as well as the D.O.T option. I tried uninstalling and reinstalling as well as downloading the latest version, but I have the same problem. I get no MB options at all (like no cpu temp, fan speed, core speed etc.). I didn't make any changes to the BIOS yet (other than changing the boot sequence), and ideas?

Quote from: nautica on 15-July-07, 13:19:02
and ideas?
A great one.
Don't use MSI's utilities. Anyone here will tell you that.

MSI P6N SLI boot problems

I recently bought a P6N SLI and new memory since my current board is getting old
When I got everything assembled and turned it on, all fans and lights started, but there were no beeps and no video
I made sure all power connectors were not loose and tried it with minimum components out of my case, still same problem
tried old memory in case new memory was faulty, no luck
I'm sure all old components are working (using them right now)
sent board in for RMA in case I got a bad board, new one did same thing
since the board didnt come with a D-Bracket, I threw one together (4 LEDs on the red pins, ground on USB) all 4 lit up "System PowerON The D-LED will hang here if the processor is damaged or not installed properly"

I am attaching a link to MSI's CPU support page..you can also get there by going to the top of the forum page, to the right of the MSI banner are all the links you need..handy. I would think, that any P4 series or any Core 2 Series CPU would be supported from the initial bios release. The "D" series are a bit out of the mainstream, but are supported once bios is updated. If you have a decent computer repair store, they should be able to pop in a P4 or C2D CPU to get it into bios and flash it. Hey, here's a thought...the Core 2 Duo chips are relatively inexpensive now..you can get a Core 2 Duo E4500 for about $125 US that will run circles around your D805...? Good luck.
Paul
CPU support link--> http://global.msi.com.tw/index.php?func=prodcpusupport&prod_no=1141&maincat_no=1

MSI Z97 Gaming 3 problems with ram

Sorry for my bad english. I have only one bank of ram 4GB Kingston Fury 1866MHz and some problems with it. When it's installed on DIMM1, in UEFI BIOS, in Windows 8.1 Pro x64, aida64, cpuz, ram saw as DIMM3! If it's installed DIMM2 saw as DIMM4, or installed DIMM3 saw as DIMM1! What's that? What kind of problem on my motherboard?
Fresh BIOS version 2.6 installed.

Quote from: rocketpowerik on 06-May-15, 17:20:02
One detail i loose in my spec, PSU: Seasonic SS-750HT(750W).
To your signature.
Quote from: rocketpowerik
And last one if i changed OC ram settings to 2133MHz or 2200, 1.65v., and CL10 Performance preset.
No much difference with stock preset.
You can only compare same software results, each software give slight different results.
Quote from: rocketpowerik
Butt i watched review when my memory with same settings demonstrated 20000MB/s read/write results.
Single channel?
Post a link.

Bios problem on MSI p6n sli-fi

Hi, on december i've the bios beta 2.13 on the msi p6n sli-fi and an e4300.
I changed to an e2140, and started the problems:
If i plug a ps2 mouse, then starts the beeps, here a record of then, i look for beep code, and dont find this combination on beeps:
If i dont use the ps2 mouse, the board start fine and goes ok.
Another problem was that the back USB, dont work, they detect perfect on the Admin Device, but if i plug something nothing happens :(, sometimes take the usb keyboard when boot, so i flashed the bios thinking could be any proccesor bios incompatibily, but after that, windows or while booting, dont detect the usb keyboard, or wharever i plug.
Yesterday, i've a surprise i attach an old USB gamepad, after a while, i taked good the gamepad (propably usb 1.1 gamepad, its a cheapper one). So after this which is the problem? Because of another gamepads, keyboard, usb flash drives and another things i plugged on the back, nothing work except for that old gamepad.
THE front usb works perfectly fine, without problems.
So what could be the problem? I think to go back to bios 2.13 beta bios, but i dont have back up :(
Please some help, i'm lost with this problem

Quote
PSU, tried two, HEC Orion 585watts and Powercooler 550w modular (UL of Topower have)
What are the amperage limits on the power rails of each PSU? (12V, 5V and 3.3V)
Quote
e2140
msi p6n sli-fi now with bios v2.5
2x1gb OCZ ddr2 800 plat rev2
1x 160gb Western Digital
DVDrw Pionner 111d
No video card?
Clear CMOS with main A/C power cable removed from PSU and load "Optimized Defaults" in BIOS after that. See if that changes anything.
If it doesn't, unplug the USB Front Panel Connector from the board's USB Pin Header. After disconnecting, check your back panel ports again.

MSI P6N SLI and HDD 2TB

Hello,
I intend to buy a new HDD Seagate 2TB ST2000DM001 and I would like to know if my computer will recognize it without a BIOS update.
My current configuration is:
MSI P6N SLI MS-7350
2GB RAM - Corsair XMS2 CM2X1024-5400C4
Seagate 320GB ST3320620AS
BIOS AMI V.2.0 01/31/2007
Nvidia NForce 650i SLI
NVidia NForce 430/410 SATA Controller (04/24/2006 V.5.10.2600.666)
Thanks in advance

It should do

MSI P6N SLI Platinum + E6850 + 533Mhz (PC-4200) RAM?

Hi,
I got hold of an E6850 (1333 MHz FSB) CPU for upgrade and I would like to know if it can run with 2Gb hynix RAM (533MHz PC-4200) on my MSI P6N SLI platinum (Rev 1.0). If it will run, how much performance loss would there be compared to using 667MHz or 800MHz RAM?
Thanks.

I am not sure if the Nforce Chipset/Memory Controller is able to support a memory bus speed that is lower than FSB Clock Speed. Intel Chipset usually can't do that (1:1 usually being the minimum ratio supported). However, on your board, the memory speed is not directly tied to the FSB Clock Speed and can be adjusted independently, so the situation may be different. The bottom line is: I can't tell you for sure if it will work or not and therefore suggest to simply test it and see what happens.
Quote
If it will run, how much performance loss would there be compared to buying PC-6400 800MHz RAM?
With the memory bus running slower than the Front Side Bus, there will be definately be a performance difference that is not insignificant.

MSI P6N SLI Platinum Sound problem

M using MSI P6N SLI Platinum (MS-7350), i am having problem with sound, i have attached 5.1 sound system all speakers are working fine accept front right, may i know what the problem is ? I've Tried everything thet was possible, Head phone, Speaker Wire, etc. etc.

What if you switched the speakers around? Does the signal from front right still missing?

MSI P6N SLI V2 power connection problems at JPW2

When Installing power supply to JPW2 the LED1 indicator extinguishes and the computer does not boot up! All other LED indicators are lit as they should. I've connected the 8 pin power supply to JPW1, and I've connected the PCIE power supply to the graphics card. Why is the computer not booting up?
I'm using the following configuration:
Motherboard: MSI P6N SLI V2
BIOS version: V1,0
Graphics card: XFX Nvidia 8800 GTS (tested and works perfectly)
CPU: Pentium 4 3,4 GHz
RAM: 4* GEIL PC2-5300 512 MB total 2 GB (tested and works perfectly)
Power Supply: LC Power LC8700 (700W) (tested and works perfectly)
Operating System: Win XP
Please could somebody help? Thanks!

Quote
CPU: Pentium 4 3,4 GHz
Please provide full CPU information.
Example:
P4 (Northwood), Extreme Edition 3.4 GHz
or
Pentium 4 550(J) (3.4GHz)
Both P4-types I mentioned as an example are not officially supported yet, that is the main reason I asked for more detailed CPU information:
CPU Support List:
http://global.msi.com.tw/index.php?func=prodcpusupport&prod_no=1169&maincat_no=1&cat2_no=170&cat3_no=#menu

MOVED: [Athlon64] Msi K8N Neo2 Platinum problems with Patriot Ram

This topic has been moved to AMD64 nVidia Based board.
[Athlon64] Msi K8N Neo2 Platinum problems with Patriot Ram

First post, whoo hooo
So what version of BIOS are u running? I recently installed the two newest versions 2.0 and 2.1, and they both give me problems. With the latest (2.1) I'm getting the same error as you. Returning back to previous BIOS fixed my problems. Oh yeah, my RAM is Kingston Hyper-X, so i don't think thats your problem.
Let me know if you fix it, thats why im here, .

Overcloking E8400/ Msi P7N sli platinium

Hello Everybody
I am french and i am trying to OC may E8400 to 3g6 for the moment. This is my spec :
PSU : Thermaltake 750W
Corsair PC26400 (800Mhz) : Timing : 5-5-5-18 at 1.9V
CPUZ tells me that i have a EPP timing : 4-4-4-12 at 2.1V Do i have to use this timing or the SPD timing ??
E8400 FSB = 1333Mhz
So my ratio is FSB/RAM = 5/6
So i am going to the BIOS in Cell Menu . I disabled the DOT , the EINST and the spectrum.
I disabled auto for manuel in cpu clock. I put the FSB to 400Mhz so 1600 in the bios. I change the timing to 5-5-5-18.
After i change the Cpu Voltage to 1.22V , the memory to 2.1V and i increase the VTT , NB Voltage a little . But i dont touch the SB voltage.
I save and when i restart my pc freeze and i have to reset the CMOS . It tells mis that my overcloking as failed but i don't know what is wrong ??? The FSB can go to 1600 without a problem no ?
My second question is how to make the ratio 1:1 . I was thinking that if put the fsb from 333 to 400 i will have a ratio of 1:1.
Thanks for the Help.

Hello
I have already read lot of review of overcloking. So i decided to overclok too .
For my case i think that i have discover the problem but i am not shure . I have read in a review of the MSI P7N Platnium that the motherbord can not go above 1333Mhz of FSB . I have a E8400 so it's by defautlt at 1300Mhz. What do you think ???
Another question is how can i know the ratio between my FSB and my memory ??? It can help me for the OC beacause i can try to reduce the frequency memory and try to see if i can exeed 1300Mhz of Front Side Bus. In cell menu i have the choise of auto , linked and manuel . When i choose linked i don't know the ratio so i can't know how my memory frequency is calulated when i change the FSB of my CPU. Try to help me here if someone can .
Don't forget i have a corsair PC26400 (800Mhz) so i can't go above 400Mhz . My timing according to CPU-Z in EPP : 4-4-4-12-2T at 2.1V
My last question is i have try to overclok directly in OS whith setFSB . But i don't know the PLL of the Msi P7N sli platinium. Can someone tell me what is it ?? I am trying to know if i can increase the FSB directly in windows Mode. Of course i will change my frequency memory in the BIOS to 275Mhz ( according to CPUZ it it's possible) to not be limited by my memory and especially because i don't Know the ration DRAM:FSB . I think it's more easily and more safe .
When i let the bios in auto i read in CPUZ a ration DRAM:FSB = 5:6 which is normal because the bus is at 333Mhz and my memory 400Mhz. But i choose linked i don't know if the ratio is the same when i change the FSB ??
Can you suggest me another program inside of SetFSB ???
If someone tell me that i can't increase 1300Mhz in this motherboard so i will stop here to oc and not loose my time.
Thanks ...

Bug USB on MSI K9N SLI Platinium & Athlon X2 3800+

Hello!
first,i'm french, so excuse my bad english(i try to do my best!)
so, the problem is that i don't have any USB working on my K9N SLI Platinium with my Athlon X2 3800+!(anywhere,all other devices works => lan, sound, storage..)
the "controlleur de bus USB" (sorry, it's french!) doesn't appear in the "Administrator of ring roads(peripherals) " (thanks reverso^^)!!!!
i've read somewhere that K8N have had a similar problem,(now there is a patch) is this the same problem???
i've mounted exactly the same configuration (except the Processor which is an AMD Athlon 3200+ (simple core))to a friend 2weeks ago,and all works!!!
my configuration :
AMD Athlon X2 3800+ (socket AM2)
MSI K9N SLI Platinium
Corsair TWIN2X2048-6400 - Twinx 2 Go (Kit 2x 1 Go) DDR2-SDRAM PC6400
Maxtor 250 Go 7200 RPM Serial ATA II 16 Mo *2
Leadtek 7900gt
thanks for your help to a little french guy(not a noob french^^)

i try this quick
thanks!
edit : it works thanks a lot!

Update on Pentium D 930 + MSI P6N SLi Mobo

A short time ago I was searching this forum for information concerning the compatibility of the Pentium D 930 processor with the MSI P6N Sli Mobo. It seems that this processor was not officially supported for this board. A few helpful people offered the opinion that they would likely work just fine together. I just wanted to get back to you guys and say thank you again, that turned out to be exactly the case. :D
After an embarrassing no-post situation caused by the leftover mounting spacers from my old board (which used 12) to my present board (which uses 9), everything went smoothly. Acronis with Universal restore allowed me to regenerate my operating system. After a lengthy update of drivers the computer was up and running smoothly and with a entirely welcome but somewhat puzzling difference. Whereas the old board (D945PVS) consistently provided an environment in which the CPU ran at 50°+ C (?!) and had transient temperatures as high as 58 - 59° C with an ambient 20° C, the new set up consistently ran below 40°. These results were consistent no matter what type of thermal pastes were used, be they my homebrewed colloidal silver in silicone stopco*k grease or Arctic Silver. (that's hilarious... the anti-obscenity software interpreted a fully normal English language word as obscenity)
Well, whatever the reason....sweet.
I have only attempted simpleminded overclocking as the options are somewhat limited by the processor. With the frequency for the GPU locked at 100 MHz, simply adjusting the FSB to 1000 raised the apparent speed of the CPU to 3.75 GHz, up from the stock frequency of 3 GHz. An attempt to set the front side bus at 1060 resulted in a non-bootable system so back to 1000 it went.
I have not adjusted any of the system voltages. So far I have not stress tested this other than to simply use the computer for several hours. No apparent problems yet. The system temperatures have remained between 38 and 40° C in an ambient 20°C environment.
The only thing that nags at me, and I'm fairly sure that this is of no importance is the fact that in device manager the CPUs show yellow exclamation marks and in properties I see a message saying that certain drivers failed to load for the CPU and that other software may be taking their place. Well, whatever this actually means, it has had no detectable impact on system performance or reliability.

Hiya flobelix
If by manually updating the drivers you mean by left clicking on them in device manager and selecting update --> search online, then yes, I did. I do not have the exact verbiage but the resultant error message was something to the effect that the drivers had installed but failed to start and something else may be taking their place.
Driver magician fails to detect that any cpu drivers are missing. Same with online testing services such as PC pitstop. | have done a cursory search using Google to find people with similar problems but I have not as of yet seen this EXACT problem.

MSI P6N SLI PLATINIUM problem with ram 800MHz

Similar Messages

Maybe you are looking for