MSI P6N SLI Platinum (Bios 1.7) No go with E8500

I have seen the Earlier post regarding the same issue. Hence updated my bios from 1.5 to 1.6 and finally 1.7. But still my motherboard is not booting up.
As per the article Bios 1.6 should work fine for E8500.
http://global.msi.com.tw/index.php?func=prodcpu2&prod_no=1140&maincat_no=1
Unfortunately the E8500 STILL refuse to boot, no matter what i try.
- No post screen,
- No error beeps
- No keyboard leds lightning up
- No indicators on the D bracket
I am using a 4 PIN CPU power connector.
Now this CPU work fine on my another motherboard Asus P5N-MX with same power supply.

Contact MSI Technical Support about this issue and see what they suggest:
http://ocss.msi.com.tw/

Similar Messages

MSI P6N SLI Platinum bios 1.7 issue

I was running an e4300 at 3.0 with vcore up 1 bump, nb up 1 bump and memory at 2.0w with bios 1.1 . I updated to 1.7 and now I can't get to be stable. I ran orthos for 3 hours , no errors. But my computer locks up randomly now, freezes up. It never did that before. Sometime it won't restart without clearing the cmos. I only updated the bios because I was thinking of getting an e5200.
Any help would be great. Running my computer at 1.8 makes me sad.
bob

Use the 1.6 version.
Ive been running it for a year and a half and have zero issues with it.

MSI P6N SLI Platinum + E8400 OC Help!, Overclocking Is Limited

Hey guys im new to the site and I need your help! :(
I am trying to get passed 3262.5 Mhz (just got it up to 3.32ghz) preferably 3.6Ghz but every time I try to raise the FSB from 1500Mhz and up it halts and I have to reset the bios. Any help is greatly appreciated. Specs Below.
MSI P6N Sli Platinum Bios v1.7 + E8400 (067A/DA07)
2 X 1GB Crucial Ballistix Tracer pc2 8500
BIOS Temps/Volts
CPU Vcore - 1.168V
3.3V - 3.344V
5V - 4.961V
12V - 12.05V
5V - 5.016V
Bios Settings
Execute Bit Support - Disabled
Set Limit CPUID - Disabled
C1E - Disabled
Spread Spectrum - Disabled (ALL)
DOT Control - Disabled
EIST - Disabled
System Clock Mode - Manual
FSB Clock - 1600Mhz
Memory clock 1066
Ratio - 9
PCI-E Frequency - 100
CPU Voltage - 0.1000V
Memory Voltage - 2.0V
NB Voltage - 1.25
SB Voltage - 1.50
FSB VTT Voltage - 0%
Memory DRAM Timings
5-5-5-15
TRRD, TRC, TWR, TWTR, TREF - ALL Set to Auto.
CMD - 2T
Idle Temp - 34
Load Temp - 42
I think thats it if you need any more info let me know. Thanks!

Hello and welcome,
First of all, 1066MHz isnt garantueed to work on that board, I have the same and although is says so on the box, it isnt supported, look here:
http://eu.msi.com/index.php?func=prodmbspec&maincat_no=1&cat2_no=170&cat3_no=&prod_no=1140#menu
533/667/800Mhz only.
To reach 3.6 try following:
Raise NB step by step, until ~1.35V max, SB @stock, FSB VTT to 4 - 8%
Set FSB to 1600 and mem to 800 on auto timings, you can adjust those later.
And leave Vcore on 0.100V as said in your post.
See if you can get it to run then.

MSI P6N SLI PLATINUM no printer

Hello all, I am hoping this is a simple fix. I just bought this board and I love it so far, I am however having trouble with my printer.
I have not been able to get it to print
System info...
MSI P6N SLI PLATINUM Bios updated to Version 1.30
CORE 2 DUO E6420 2.13G (1066Mhz)
CRUCIAL 2GB DDR2 667 (1GB x 2)
GIGABYTE GV-NX85T512HP GeForce 8500GT 512MB
EAGLE VIPER ATX MID TOWER W/500W POWER
Windows XP SP2
I have...
been in the bios and can't find the port settings
run the Windows troubleshooter
Printer port doesn't show up in the system info and when I install a new printer port it lists it as LPT3 but not working.
Any help you can give me would be great.
Thanks

After searching the bios again I found that the port was disabled Printing fine now

Who has this setup - MSI P6N SLI Platinum & E8400

This message is intended for anyone who has the MSI P6N SLI Platinum & E8400 in a working state.
I've had the pleasure of perusing these forums for a while in hopes of finding an answer as to why my E8400 isn't working with my P6N SLI Platinum. I've updated my BIOS, I've RMA'd my chip, I've even contacted MSI support (with no reply I might add). I have been so careful when handling these components and thoroughly reading the instructions, to no avail. I've got the board and all components working with a different processor. I've tried the voltage modifications that many have said work, I've tried different memory, I even tried a different video card. So I'm stuck in the same boat as many it seems, however there are one or two posts on this forum and others where people have said they actually got it to work!
So now I really hope I can get this question answered - What is a working config? One of the things I haven't tried yet is a new power supply. My current PS is 650w, but has the 4 pin CPU power connector. From the posts I've read, it shouldn't matter if I have the 4 or the 8. But in reality, does this CPU work on the P6N Plat with an 8 pin connector? I'd be willing to go buy a new PS if thats the case! What else could possibly be the issue? Any and all feedback is appreciated. i really didn't want to start up another thread for this proc/board issue, but perhaps someone else has joined this board by now that may provide the little piece of info that I've been missing.
Cheers,
Aaron

according to the website, the 1.6 BIOS had cpu updates in march so I's assume it would have support for the E8400.
What exactly happens when you turn on the system with the E8400?
-=Mark=-

MSI P6N SLI Platinum MS7350 Ver 1.0

I have a MSI P6N SLI Platinum MS7350 Ver 1.0 motherboard. The screen will go blank, they keyboard will lockup, and the only thing that fixes it is a hard re-boot. It does it more often if I am playing a game, but it will also do it when I am not using it. Can you help? My system specs are:
win7 64 Ultimate SP1
8 GB ramm
Galaxy Nvidia Geforce 9500GT display adapter
Samsung Sync master 932BW/BW1932/932BWE plus (digital)
LG GSA - H62L scsi cdrom device
Intel Cor 2 Duo E7300 CPU

Quote
Same Exact issues here.... I was thinking of attempting to re-flash the bios
but could just see it freezing in the middle...... real Quality
You attempted to re-flash ? What method did you use ? Always use the forum flasher; it still holds a 100% success rate. >> Use the MSI HQ Forum USB flasher <<

MSI P6N-SLI Platinum Multi-gpu enabling

Owners of the P6N SLI Platinum mobos. I'm having trouble Figuring out how to enable my two EVGA 256-P2-N636-AR GeForce 7950GT in SLI mode. The manual I have doesn't coincide with what my system is telling me. Anybody out there please shed some light on my predicament. thank you. >:(
my system is as follows
1: Intel Core 2 Duo E6700 Conroe 2.66GHz 4M shared L2 Cache
2: MSI P6N SLI Platinum LGA 775 NVIDIA nForce 650i SLI
3: Kingston HyperX 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800
4: 2 EVGA 256-P2-N636-AR GeForce 7950GT 256MB
5: system drive - WD Caviar 160GB 8MB SATA 3
6: backup drive - Seagate Barracuda 320GB 16MB SATA3
7: Windows Xp home sp2
8: PSU Antec Neo HE 500

read Moan Guide 1st and provide full system specification including PSU details(look over PSU sticker for them)
made sure JPW1 is connected,
install both VGAs:
made sure SLI Bridge is connected between them,
made sure addiction power cable is connected to each VGA,
connect monitor cable to the 1st VGA(located in the 1st PCI-E x16 slot)
go in BIOS and check for SLI related options, if exist ensure that they are configured property,
install latest chipset drivers for your board from Nvidia: http://www.nvidia.com/content/drivers/drivers.asp
install latest VGA drivers from Nvidia(94.24): http://www.nvidia.com/object/winxp_2k_94.24.html
type in "run":
rundll32.exe nvcpl.dll,LaunchMultiGpuApplet /* click OK or hit {ENTER} key when its done */
and Enable SLI from there, and config "OK":
to verify that SLI is functional correctly get a Everest:
http://www.lavalys.com/beta/everestultimate_build_1059_welo4kjhnxa.zip
navigate to GPU page and check it:
for SLI troubleshooting and guides look here:
http://www.hardforum.com/showthread.php?t=938853

MSI P6N SLI Platinum + 3TB HDD

Hello, I want to buy a 3TB SATA DRIVE for my old MSI P6N SLI Platinum and i want to know if i will have any problem!
SPECS:
MSI P6N SLI Platinum (nForce 430i) Bios v1.7
Intel Core 2 Quad Q6600@3Ghz
4x1GB Kingston ValueRAM 1Gb DDR2 800
F.A. XION XON-630F12P 630 Watts
Sapphire Radeon HD 5850 Vapor-X 1GB DDR5
Windows 7 Professional x64
HARD DRIVE:
3TB TOSHIBA DT01ACA300
thanks!

As I already said:
Quote from: flobelix on 29-January-13, 23:58:02
No, that won't work as that requires a UEFI bios and GPT format which is both not possible with your old board just supporting classic bios. You won't be able to access the entire drive space which makes a (costly) 3TB HDD quite useless.
Better just get nothing above a 2TB HDD.
Connection won't change that.

MSI P6N SLI Platinum + E6850 + 533Mhz (PC-4200) RAM?

Hi,
I got hold of an E6850 (1333 MHz FSB) CPU for upgrade and I would like to know if it can run with 2Gb hynix RAM (533MHz PC-4200) on my MSI P6N SLI platinum (Rev 1.0). If it will run, how much performance loss would there be compared to using 667MHz or 800MHz RAM?
Thanks.

I am not sure if the Nforce Chipset/Memory Controller is able to support a memory bus speed that is lower than FSB Clock Speed. Intel Chipset usually can't do that (1:1 usually being the minimum ratio supported). However, on your board, the memory speed is not directly tied to the FSB Clock Speed and can be adjusted independently, so the situation may be different. The bottom line is: I can't tell you for sure if it will work or not and therefore suggest to simply test it and see what happens.
Quote
If it will run, how much performance loss would there be compared to buying PC-6400 800MHz RAM?
With the memory bus running slower than the Front Side Bus, there will be definately be a performance difference that is not insignificant.

MSI P6N SLI Platinum Voltage regulator cooler size question

I have a question about MSI P6N SLI Platinum's Voltage regulator cooler. Is it the same size of K9N SLI Platinum? The reason I ask is I plan to use water cooling on it. But the only regulator waterblock I can find is desgined for K9N SLI Platinum from aqua computer http://www.aqua-pcs.co.uk/index.asp?function=DISPLAYPRODUCT&productid=218. So can I use this one on P6N SLI?

I guess not... P6N is much thinner, if your K9N VR cooler is as thin, then it can fit in. But I guess not.

MSI P6N SLI Platinum Sound problem

M using MSI P6N SLI Platinum (MS-7350), i am having problem with sound, i have attached 5.1 sound system all speakers are working fine accept front right, may i know what the problem is ? I've Tried everything thet was possible, Head phone, Speaker Wire, etc. etc.

What if you switched the speakers around? Does the signal from front right still missing?

MSI P6N SLI Platinum OEM Modification Question

The MSI P6N SLI Platinum OEM edition motherboard comes with all the circuit layout needed to support 2 SLI x16 Style connectors for SLI'd video cards. However the OEM only comes with one installed and an empty slot for the other. What resistors and the like would I need to add to the board in order to add the pcie x16 connector to the empty area on the board? I've already found a source for the actual slot, and I know I am going to need to add a resistor of some type to the empty resistor slot directly above where the PCIe slot will go. Beyond that I don't know what else I need to do, or what type of resistor is needed.
Oh yeah, and where can I go to buy the optional accessories for this board that came with the retail version? I would have prefered the retail version but the board I have came as part of a kit.

Hello Tornath,
you have already mentioned yourself, that you have an OEM-Board, not an MSI-Retail Board. MSI does not provide end-user support for OEM products, as this is the responsability of the OEM Vendor who is selling OEM Boards under a different name. Also, this forum will not support OEM Products and that is why I will have to close this thread.
However, before you waste huge amounts of your lifetime with trying to add a second PCI-Express Slot to your OEM-Board, let me explain to you, why your plan is rather pointless:
1) The only OEM-Board of this class I know of, has the model number MS-7350VP. If there ever was a marketing name, it would be called P6N Platinum (not P6N SLI Platinum), and there is one simple reason for that:
2) This particular OEM Board has an NVIDIA nForce 650i Ultra Chipset (as opposed to the NVIDIA nForce 650i SLI), and if you look at the specifications for NVIDIA Chipset on the official NVIDIA Chipset Specification Site, you will see that this Chipset does not support the NVIDIA SLI™ Technology: http://www.nvidia.com/page/nforce_600i_tech_specs.html .... That is basically why there is no additional PCI-Express Slot in the first place. So even if you should succeed in adding a secondary PCI-Express Slot to the board physically, the chipset will render it more a less useless in terms of running two video cards in SLI mode.
**TOPIC LOCKED**

P6N SLI Platinum Bios update in Vista x64

Just wondering how I update the bios for my P6N SLI Platinum in Vista x64? When I d/l the bios all the stuff is for 2000/me/xp. Why is there no vista support under anything?

Use the USB flashing tool developed here at the forums.
clickme>>MSI Forum HQ USB flashing tool!!!<<clickme

P6n SLI PLATINUM bios v1.2

So I upgraded to 4gb ram finally, and have got it to work without errors in dimm slots 2 and 4, and have been having performance issues such as slow loading, stuttering in games, and just in general slowdown with loading up applications, but absolutely no crashes or freezes of any kind, no BSODs or anything else that would be hardware related I assume.
Defragged, fresh install of windows 7, video card drivers updated and everything else checks out fine. The only thing I can think of is that over in HardForum doing a google search brought me to this post:http://www.hardforum.com/showthread.php?t=1164174 with issues related to 4gb on the mainboard having slowdowns with older bios versions.
Seeing as how this is relevant to me getting new memory, my patriot memory gave out with BSODs so I was forced to upgrade but had way better performance with just 2gb stick of ram (even in win7).
Should I do a bios update?
Specs:
EVGA 8800gts 540mb 195.62 driver
4gb A-Data ram 5-5-5-12 2t clock, 1.9v
Windows 7 64-bit
Bios v1.2 A7350NMS P6N SLI Platinum Socket LGA-775
Core2duo E6600 @2.4ghz
I haven't really done much upgrading since I purchased this a few years back, and quite surprised to see the hit and stuttering in performance in games all of a sudden after upgrading to new ram, and the ram tested out fine for 3 days straight doing multiple passes with memtest 4.0. I tried doing it in DIMM slots 1 and 3 but have been getting errors, maybe I've got a bad board?
Quite confused as to what step I need to take next, thanks for any help!

Quote
Should I do a bios update?
Yes. >>Use the MSI HQ Forum USB flasher<<

P6N SLI Platinum BIOS issue...

So I purchased an e8400 processor after the 1.6 BIOS update came out for my P6N SLI Platinum, got it yesterday. I put the processor in and it didn't work . I turned to Google to have the internet fix the issue, and it seems if I adjust some options in my BIOS, it may make the e8400 work. Two of the things it said to change were EIST and C1E. I went into my BIOS, and tried hitting F4 in the CPU menu to get C1E to show up, but it won't. The EIST option is no where to be found either...
Anyone else running into the same issue, or got a e8400 to work after changing stuff in the BIOS?
Thanks a lot!
EDIT: Forgot to post my system specs
Mobo: P6N SLI Platinum
CPU: Intel Pentium D 930
RAM 2GB (1GB x2) Patriot DDR 667 (PC 5300)
GPU: eVGA nVidia GeForce 8800GT
PSU: Thermaltake 500W

I used that bios, but on my regular p6n sli and got it to work. here is my topic on it
https://forum-en.msi.com/index.php?topic=115998.0
Dont clear the bios after you take out the old cpu or it wont work
I have been tinkering with it all day just to see what the actual problem is and it doesnt seem that it is the EIST OR C1E. from what I have done it seems that it is a problem with the voltages that keeps it from booting. If you change those with the other cpu in and then save and exit. Dont let it reboot, shut it off before it starts to boot up again and put the e8400 in

MSI P6N SLI Platinum (Bios 1.7) No go with E8500

Similar Messages

Maybe you are looking for