MSI P6N SLI V2 does not boot up from cd/dvd and few other problems

HI
I just bought a computer P6N SLI V2 + E6750. It has following problem. It does not boot from cd.
I have Sata HD. CD/DVD is installed to IDE as a master.
I have done settings in bios so that First boot is cd/dvd and second is sata HD. Anyhow it still goes to the hd and stars windows.
I was only able to boot up from cd when I disabled hd from boot sequency. Meaning I left only cd/dvd there.
Hopefully you pro's can help me.
Then there is another problem. Windows is telling me that it found new pci device. I do not know what device. I have only Graphig card (geforce 8800 gts) installed into pci-E. Drivers and software are also installed, I assume proberly. How to find out what windows thinks it found.
Third problem is onboard soundcard. I cannot get any sound out from the machine. I have downloaded driver from realtek, but still no sound.
Unfortunatelly I do not have original software for motherboard. Only the latest from MSI website.
Hopefully someone can help me.
thanks.

About bootup, i dont know yet.
To find out what windows found, look in devicemanager.
To go there go to controlpanel, system then choose devicemanager.
There you can see what's installed.
Last, your soundcards needs to be enabled in bios, under integrated peripherals there should be a line with "onboard sound", enable this and sound should work, unless its broken.

Similar Messages

Followup-- MSI P6N SLI Platinum does not work with E8400

I am just following up like I said I would... and the *RMA'ed* E8400 still fails to post with a BIOS updated (v1.6) P6N SLI Platinum. It works fine with an E4500... but not the E8400. MSI really shouldn't say it's compatible when it's not. I am going to send the board back to Directron and replace it with the new Gigabyte GA-EP35-DS3L. Very unhappy with MSI right now and probably won't buy from them again. I'm going to stick with another gigabyte for now. Anything I can do before sending it back tonight? I am very disappointed, especially because this really is a perfect board for me.

You can drop MSI an email to see if you are able to get an engineering BIOS to try out.
>>How to contact MSI.<<

Dv 6809wm laptop. Computer still does not boot up when battery out and ac adapter plugged in?

dv 6809wm laptop. Computer still does not boot up when battery out and ac adapter plugged in?
It lights up initially for a split second when I push power button, but does not continue to boot up. When ac adaptor is put in it glows blue like it is supposed to. Any suggestions?

i'm going to try to see if a different ac adaptor will work hopefully that solves the issue.

The Notification Center Yosemite primary user does not work in my Macbook pro and the other users if it works.

The Notification Center Yosemite primary user does not work in my Macbook pro and the other users if it works. How can I fix it?

The Notification Center Yosemite primary user does not work in my Macbook pro and the other users if it works. How can I fix it?

MSI P6N SLI Plat - Harddrive not appearing in my computer

Hi guys,
Ive just bought an additional sata2 drive for my pc. I already have a raid - 0 setup.
It shows in bios and i managed to find it using the 'manage' option through XP. Its been formatted to NTFS, and despite being able to copy files over to it,
it doesnt appear in the My computer window?? this is really beginning to bug me, the only advice online has been to format the drive which ive already done twice!!
I am no expert, so iam out of ideas. Any help appreciated.
Thanks
Intel E6600
2 Gig DDR2 Corsair 6400C4
MSI P6N Sli Platinum
XFX 8800 GTS 320 XXX
2 x (34G) Western Raptors Raid -0
Hiper 480W psu

Hello,
Quote
It shows in bios
Quote
i managed to find it using the 'manage' option through XP.
You mean XP Disk Management?
Is/was there a drive letter assigned in disk management?

K9N SLI Platinum does not boot

Hi
suddenly my computer does not boot -after a short 10 days of use. I just have a blank screen.
The D-bracket shows 2 green on top and 2 red on bottom, which according to the manual means "decompressing BIOS image to RAM for fast booting". There it hangs.
I unplugged all drives and memory and I flash the CMOS as shown in manual p2-20. No result.
Any suggestion?

First, thanks for helping.
I tried different combination of RAM positioning using DIMM1 and DIMM3, but with no result (as I read the manual, it says DIMM1 needs to be used first, and then DIMM3). I also tried DIMM3 alone (the slot near the CPU).
I also disconnected the power cord to flash the CMOS. No change there.
I don't have any other card in the system, just the video card on the lower PCI Express slot (farther from the CPU).
I might add that I did not update the BIOS with the latest version. I left it as it was when I bought the board. This BIOS version was not able to recognize the CPU and it displayed an error message at POST. The OS was dealing with it properly and all seemed to work fine.
The problem started after a cold reboot if I remember.
PSU Specs (see also my updated signature)
18A on the 12V rail
Bought it there (full specs): http://www.tigerdirect.ca/applications/SearchTools/item-details.asp?EdpNo=2235424&Sku=O261-2005

MBP 15" 10.6 does not boot up from Installation disc, why??????

Good day,
my question is simple, so please let the answer be simple:
I have done partition on my MBP today, in order to give me more redundancy in case of a Hard drive failure. I witnessed one yesterday on a brand spanking Imac--> not pretty--> the white screen of death!! I thought I´d better cover myself and I split my HD in two--> no probs.
Anyways, I decided to try to boot from my original installation disc--> 10.5.7, Leopard.
I booted while pressing "C", or holding "Option"……and always ended up with the same thing:
It just takes me to a language selection screen, I selected my language, and then it takes me to the software installation--> but I don´t want that--> I just want to reboot from my disc--> as a general test. (Just in case of that dreaded white screen, one day!!)
So, I went to to "Stop installation" in the menu above, and I chose "Reboot" and then I chose my installation disc--> and again and again, it just takes me back to the language screen etc etc etc!!
It´s like a Merry go Round………….
What am I missing??
My Snow Leopard installation disc does exactly the same, by the way…………..
Cheers,
MXP 150 Patriot

"perhaps I didn´t explain myself properly:
I would like to boot up from my installation disc, in other words, being able to log in and see my Desktop etc.
All I get from my disc is an installation menu (after the language selection) and if I try to boot up from there (to my desktop / background etc) by selecting "stop installation--> start up disc".........it goes back to the language selection and the software installation........just where I was 3 minutes ago!
What am I doing wrong?
My friend booted up the other day from his FireWire external hard drive and he got everything, SO quick! His personal desktop, everything!
Hopefully you can tell me what I´m missing........."
You're missing the point. When you boot from your installation disk it's to install the OS and/or repair the disk and check the hardware, etc.. Your friend has a bootable external drive. he used the OS Installation disk to create that.

Mac does not boot past white loading screen and disk cannot be repaired?

So when I turn on my Macbook Pro and it does not boot past a white screen with the Apple logo, loading wheel and progress bar. When the progress bar completes, the Macbook shuts down and when I open it again the cycle is repeated. I have opened it in Safe mode and it still showed the same thing. So I opened it in Recovery Mode and had Disk Utility verify and repair Macintosh HD. As it turns out, Disk Utility said Macintosh HD is beyond repair and I need to back up my files and reformat the whole Mac. Unfortunately, I have never used Time Machine since I started using the Mac and I obviously cannot use it now since startup does not even get past the white screen.
How do I reformat the Mac when it does not even go beyond the white screen during startup? My Mac did not come with any recovery or installation disks. Are my unbacked up files gone for good?
Thanks.

PochAstudille wrote:
How do I reformat the Mac when it does not even go beyond the white screen during startup? My Mac did not come with any recovery or installation disks. Are my unbacked up files gone for good?
Since you are able to get into Recovery Mode (Command+R), you can erase/format your Mac via Disk Utility.
Your files/data might be OK. One way to get your data off since you have no back up would be to have another Mac and connect the two via a Thunderbolt cable or even an ethernet cable (I think), then restart your 'bad' Mac into Target Mode by restarting and pressing the T key. Then go onto the 'good' Mac and see if you can copy the data files you want over to it.

P6N SLI Platinum does not POST or beep

See my signature for specs.
Problem: The MoBo suddenly stopped booting. When I press the powerbutton the fans start spinning, the green LED on the MoBo lights up, hd's spin up, and that's about it. The monitor goes into standby. There's no POST, not even beeps.
Tried:
Clear cmos (multiple times)
Replace PSU (tagan > corsair)
Replace VGA (radeon > nvidia)
Bare boot (MoBo, 1 stick of RAM, CPU and VGA)
Other RAM (kingston hyperx ddr2 800)
Other CPU (q6600 > some core2duo, 2 cores)
Reseat CPU, RAM, VGA, cables..
Can it be that my MoBo is just.. dead..?

Hello and welcome,
by the looks of it, it could well be.
Look on the board for leaking/bulging caps/condensators, if you find a few the board is probably dead.
They have a habit of breaking/bulging when they age and then they go kaput, unfortunately.

17-inch Mac Book Pro does not boot. No startup chime and no video.

Hey guys,
My Mac Book Pro refuses to boot. Whether it's running off the power supply or on the battery, it does the same thing: I hit the power button, I hear the disc drive make it's usual sound, but no apple boot chime, and no video. It just sits there, blank screen and all. Last night in my frustration, I held the power button down for about 5 seconds and the light in front started blinking as if it was expecting a firmware update. I immieditely shut it off. I hope that didn't make the problem worse, but regadless it still has the same problem. I have a feeling my logic board took a dive. What's weird is, I was using it, it was plugged in, I left it for a bit, it went into sleep mode, and that was the last time it was on. It's as if I can't get it out of sleep mode. I've turned it on and off a dozen times, taken the battery out, etc.. And nothing. Any suggestions?

Dead On Arrival (DOA) Product: System Failure Out of the Box
An Apple-branded hardware product is considered DOA if it shows symptoms of a hardware failure, preventing basic operability, when you first use it after opening the box. If you believe that your product is DOA, please call AppleCare Technical Support at 1-800-APL-CARE (1-800-275-2273) within 30 calendar days of the invoice date. AppleCare Technical Support will determine whether the product is DOA and offer you the following options:
Replacement: Apple, at its expense, will ship another of the same product. AppleCare Technical Support will put you in touch with an Apple Store Customer Service Representative who will arrange for replacement and the DOA product’s return.
Service: You may have the product repaired. However, once you choose that option, you may not request replacement of the product.
If AppleCare Technical Support determines that a returned product is not DOA, Apple will apply Apple’s standard product warranty to the product. Further, if AppleCare determines that you have misrepresented a returned product’s condition and that the product is not DOA, Apple may impose a $400 handling fee.
This DOA policy applies only to Apple-branded hardware products currently offered at the Apple Store. As new products are offered, Apple reserves the right to determine whether or not this policy applies. This DOA policy does not apply to third-party products that do not bear the Apple brand name. You must call the manufacturer directly with any third-party product issues.

T60 does not boot up from sleep mode

Hi,
My client has a T60 with an advanced docking station. When he leaves the office he undocks and puts it into his bag and goes home. The laptop is set to sleep when the lid is closed. When he returns the following day, it has switched off and when he redocks and switches it on, it says it is resuming then goes blank. It is on, hard drive light flickering etc but he cannot work on it. We have to hard reset and then halts at the safe mode options, I choose "start Windows normally" and it boots up fine. It's running Win7 Professional. Please advise if there is any software that can undock gracefully or any other suggestions would be appreciated...thanks,

he needs to switch off the laptop and then undock, otherwise the machine would think he is still in docked mode.
Or he needs to eject the machine out of the docking station (by pressing the no. 1 eject button on the dock), put to sleep and then undock.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

I bought a MacBook Pro from Indonesia on 24 th of February 2012, but it does not boot up from last Monday , then I sent it to Sri Lankan authoriser ( future world) with the bill, but they say no warranty

I bought a MacBook Pro from Indonesia on 24th of February 2012, but it doesn't boot up from last week, Then I took it to Sri Lankan authoriser( future world) with the invoice which I got when I purchased it, but they say that my warranty is not available. WHY I S THAT?

Give Apple a call:
http://support.apple.com/kb/HE57
Ciao.

Phone does not ring though ringer is on and music/other sounds can be heard. Why?

my phone does not ring even though the ringer is on. music plays and other sounds can be heard but it does not ring. Why?

Hi there gizmotoall,
You may want to verify your settings using the information in the article below. Also, double check that the side switch isn't set to silent mode.
iOS: Understanding sounds, ringtones, and alerts
http://support.apple.com/kb/HT5800
-Griff W.

MacBook Pro does not boot when 'cold', Windows 7 on the other hand boots without any problem

Hey everyone,
I have a strange problem with my MacBook Pro mid 2009 13" running OSX Mavericks. For more than a year I have trouble booting my laptop. A 'cold' start (a fresh boot) usually ends with the prohibition sign on a grey back ground (starting in verbose mode results in the error message that the main drive could not be found). So far so strange.
I have Windnows 7 installed as a bootcamp partition. If I start the laptop with Windows booting is no problem and Windows runs smoothly (what a terrible world we live in). If I let the laptop run for let say 10 minutes and restart the laptop Mac OS starts without any problems. (It doesn't work if I immediately restart after windows booted; also reinstalling Mac OS as a clean install from an external medium did not change the problem; disk utility always finds something to repair but neither discpermission repair nor disk repair got rid of the problem).
As an additional comment a WD 500GB Scorbio Blue replaced the original hard drive about a years ago. I had no problems with the hard drive initally and I can't really believe that there is a problem with the hardware, I mean, why does Windows start and Mac OS doesn't?
Thanks for your time and help!
Marco

This isn't a direct answer to your issue but have you considered installing Wine so you can run the occasional windows app directly in OSX? It's a much more elegant solution IMHO. This avoids restarting all the time with Bootcamp and avoids crashing all the time (and the security risks) with Windows running.

Satellite P840/016 does not boot from CD or DVD

Using F2 enabled the BIOS to boot from optical drive, saved and re-started. Finds the bootable CD created from the same laptop using the repair disc from Windows 7 recovery but does not boot.
Tried Ubuntu DVD which works as boot disk on all other laptops - still does not boot.
Changed the setting in BIOS to non-secure - same problem.

Thanks - tried this pressing F12. Message appears on the screen to press any key to boot from DVD. Key pressed, the DVD is read and then delay with blank screen. The laptop goes back to start screen and than goes to boot from the HDD. Also tried making USB as bootable. Pressed F12 and selected USB as boot device. Reads the USB and after a period of time boots from HDD.
Checked DVD driver - it is the latest.
Operating system is Windows 8 pro.
RAM is 8GB, processor is I7 and HDD is 1 TB. Laptop is only 3 weeks old

MSI P6N SLI V2 does not boot up from cd/dvd and few other problems

Similar Messages

Maybe you are looking for