MSI R4850 PROBLEM - PLEASE HELP FAST (UPDATED) :S

I install my new PC and what do you know, there are exclamation marks on the POST and BIOS screens replacing some parts of the background... But when windows starts everything looks fine. I can watch movies and there is no problem. But then I saw this in the VGA driver tab:
So I install a few games, and it is similar to that picture. The whole screen is covered with little squares on some spots and there seems to be faulty graphics.
While playing a map in Warcraft, not only the graphics was like this, but every now and then the screen would freeze, go black and return to the same bad graphics. Also after 5 minutes it gave me a BSOD.
I have the latest ati grafics drivers, and I tried replacing the 4850 with my old video card, an MSI Nvidia N7800GT and these problems are not present with that card, so it has to be the a problem with the 4850.
So what is wrong with the VGA? Is it some hardware fault? What should I do?
My system (only a day old):
MSI P45 Platinum (Zilent) BIOS v1.0
Intel Core 2 Duo E8300
A-DATA Vitesta 1066+ 2x1GB
MSI R4850
1XWD RAPTOR 74GB
1XWD CAVIAR 200GB
1XWD CAVIAR 500GB
1XSAMSUNG SATA DVDRW 22x
PSU: Cooler Master Real Power M520
HANNS-G HI221DP (22" Widescreen connected with DVI-D Single Link Cable)

OK, so I tested the VGA in another system. And as it started it showed the exclamation marks in post again. Then I installed the drivers and i restarted, and the exclamation marks were gone. Then tested games, Warcraft and Crysis and everything works splendid. This was on my friend's PC which is:
MB ASUS P5Q Updated to Latest BIOS
PQI DDR2 800MHz 2GB
CPU Intel Core 2 Quad Q6700
HDD 320GB Hitachi 16MB cache @ SATA2
Windows XP PRO x86
So the VGA is ok here, but doesn't work fine on my system. Any ideas?
EDIT: Updated BIOS version to 1.4 and the problem persists... some help pleaseee!

Similar Messages

  • Nasty MOTU MSI / Modulation problem - please help!!

    OK, I've searched high and low for a solution to this, but no joy, so here goes...
    For weeks now, I've had an issue with MOTU's Symphonic Instrument.
    Parts recorded with it play back distorted if the active track in Logic's arrange window is not the one the plug-in is on.
    The 'distortion' is in actual fact the MSI playing back as if the modwheel is full on. It sounds like a very fast square-wave gate. Whipping the wheel back and forth back to zero while the MSI track is active will temporarily cure the problem, but as soon as you change tracks, it's back. It doesn't make any difference whether the plug-in is configured in single-channel or multitimbral mode.
    I've also had the same thing happen with Absynth, which suggests it might be more something to do with the way Logic handles CC#1 data from the Korg Kontrol 49. There are a number of reports about the buggy implementation of CC#1 on this controller, but they mainly concern it being used in Native Mode, which I don't use, as I need a working modwheel. Swapping the Korg out for a Roland PC300 keyboard controller had no effect in any case.
    It may have been caused by CC#1 events lurking around in the MIDI parts... some of them were originally recorded with Garritan Personal Orchestra, which uses the modwheel as a volume control. However, I couldn't find any such events, and although I might have got nearer to figuring out what's causing the problem, I can't get it to stop doing it.
    Inserting "CC#1 = 0" messages into the part's event list doesn't help.
    Recording modwheel resets on the same track doesn't help.
    Turning on the "Chase Controllers" preference doesn't help.
    Using a different controller keyboard doesn't help.
    Setting fire to the computer doesn't help.
    I am unable to perform the 1.1.1 update for MSI, so that doesn't help. The plug-in crashes Logic's validation with a "Fatal Error." This results in it being greyed out in the AU Manager list, and I am therefore unable to enable it manually. I'm currently swapping emails with MOTU tech support about this.
    If anyone can help resolve this while I still have some hair left to tear out, there's at least 3 pints of strong beer in it for them....
    G5 2GHz, 8GB RAM   Mac OS X (10.3.5)   Logic Pro 7.1.0, MSI 1.0.0, MOTU 828mkII, Korg Kontrol 49, bad headache...

    I would say do figure out how to make the upgrade first and foremost. A lot was done in that upgrade, and one may have been to fix this bug.
    As for cc data, have you checked the track automation for the track with MSI? I know it's an obvious question, but if there's ghost data it will show up there.

  • MSI Bundle problem (please help)

    I need your help. We have zenworks 10.3.3. I made a msi install bundle and bundle installs normaly, but remains pending. I checked the msi log and it says that it installed correctly. Last line is MainEngineThread is returning 0. Why Zenworks dont realise that the bundle installed correctly, what am i missing???
    Benny

    The fact status updates for other bundles, seems to eliminate the Status
    Roll-up as the root cause.
    Perhaps Reboot the Device?
    Maybe ZCM thinks the install is not yet complete?
    If you try to manually launch the bundle again, does it reinstall?
    If so that would tend to indicate ZCM thinks its not installed.
    On 7/26/2011 11:16 AM, Benius wrote:
    >
    > Thank you for your answer. When I made a bundle that just deletes one
    > file, it worked fine, this only happens with a msi (pending until I
    > remove the assignement). Also when I watch the ZENworks Progress window
    > it says installation completed. I know it is very difficult to help in
    > this kind of situations, but any tips on what to check?
    >
    >
    Craig Wilson - MCNE, MCSE, CCNA
    Novell Knowledge Partner
    Novell does not officially monitor these forums.
    Suggestions/Opinions/Statements made by me are solely my own.
    These thoughts may not be shared by either Novell or any rational human.

  • TS4436 Iphone 4 camera worked fine for 2 years then turned all flash photos red after installed Fast Torchlight App - deletion of app did not fix camera problem - please help?

    Iphone 4 camera worked fine for 2 years then all photos with flash came out as red after installed Fast Torchlight App - deletion of app did not fix camera problem - please help?

    Try This...
    Close All Open Apps...  Sign Out of your Account... Perform a Reset... Try again...
    Reset  ( No Data will be Lost )
    Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
    http://support.apple.com/kb/ht1430
    If no joy...
    Connect to iTunes on the computer you usually Sync with and “ Restore “...
    http://support.apple.com/kb/HT1414

  • MSI 645 ultra xp / 2000 problem please help.

    I've got 3 MSI 645 ultra mobos. I've tried every thing i can think off to get xp installed and working. I don't get as far as formating the hard disk in the setup. I relpaced the power supply with a qtec 550 watt power supply (the gold one). i've flashed the bios to 1.9, i've used different hardisks and cables. I've checked the memory PC2100 and 2700. It's a pentium 4 1.5, I've tried a 2g in it as well. I'm using an ATI radeon 7500 but have tried a s3 agp card. All the other components work fine in another machine but not on my 3 MSI boards.
    Please help some one out there must have had the same problem. I'll buy the first person who fixes it cakes!!!
    Ta
    Gus

    Hi,
    I ran memtest 3.0 and there were no errors. it ran for 9 hours.
    I am only using one hard disk at a time. it's set as a master on IDE1 and the CDrom is on IDE2 as a master. should I use cable select?? I also tried the hard disk and CD on ide2 and that did not work either.
    Ta

  • [TV@Master] Problem please help

    I have Msi.mother board PT8-Neo -LSR ,  Model No.Ms-6799 , main board bios -Phonenix ,maind board version i updat it to 2.2 , cpu size 2.4 G celleron D/256/533 , memory size 256DDram (400),display card Nvidia Riva TNT2 model 64
    the problem that i face it when i put my TV@nywhere -master card ,the pc stop at the main page that show the biso version and name of bios company and the letters do not bost well it look like a virus work , and when i take tha card off the pc go normally , i tried put it to other PCI the same problem
    please help

    i meany by fix the problem of getting the pc go on to windows with card on PCI salot but i still have the broblem of the driver
    please read my reply again
    my operating system is win me and i have also another pc have XP
    when i log in to windows the system show that found my TV@nywhere card but it didnt took the installatin driver for it i tried to install the driver directly
    but it give me this 2 mesages  when i try to install the driver
    MSI TV card is not found ,stop the installation
    the other message is
    MSI pvs driver installatin failed
    i download the driver from msi page also give me the same messages
    for known on Device Manager it show me that the driver there but do not have the driver and the ? mark beside them
    what to do now 

  • P6N Lots of problems please help

    P6N Lots of problems please help
    The setup is the following:
    P4 D935 3.2gHz
    P6N Diamond MS-7320 Bios 1.3V
    Corsair XMS2-6400C4DHX
    NX8600GT-TD512EZ/D2
    Seagate Barracuda 7200 250Gb SataII 16Mb
    Akasa 460W Dual Rail
    Please help I have lots and lots of problems with lockups that can happen any time post , bios , loading vista and sometimes during OS. Some times will work ok play games etc. Already tried different combinations fitting the mem modules even tried and some pc4200 modules same problems. Spent lots of hours clocking the mems with different settings but non is stable. I am not interested in overcloking just to make it stable to start with. When is actually running is fine is more than enough for me. Already looked to lots of posts on the msi forum but… Since the cpu is old can I go back on an older bios version???? The Corsair modules have to run at 2.1V or is it possible to use them with slower setting. So confused so lost ….. please HELLPPPPP
    Any help greatly appreciated.

    please, don't buy any more unneded parts.  first find the problem then buy if no solutions available.
    One thing I find with BIOS issues is to do a full clear.
    1. disconnect the power cord from the power supply(turn switch to off if there is one.
    2. hit the power switch to clear the power out of the system.
    3. set the cmos jumper to clear and leave there if one is available.
    4. Pull the battery.
    5. carefully short out the battery connector on the motherboard to drain any power left.
    6. press the clear cmos button and hold for 30sec minimum, if you didn't have a jumper to set. 
    7. replace battery, move jumper back, plug in power cord, turn on power sipply switch.
    Now it should hopefully power up.  go into BIOS and load optimized results. hit save and exit and when it gets back to the post screen, go back into bios and set your normal MB settings(ie. set boot devices, boot order, disable sound if using sound card, etc...)
    go into your H/W Monitor section and list the CPU Vcore settings to make sure it is getting the power it needs.  I just looked it up and it's suppose to run from 1.225v - 1.325v.
    also, try your most generic ram you have with auto settings.  the faster the ram usually the more volts they need and default volts are 1.8v for ram and sometimes faster chips have issues with lower volts.
    Let me know how this works for you.
    -=Mark=-
    ps. make sure everything is unplugged from the computer you don't need.  just cpu, 1 stick of ram, and video. and of course keyboad and mouse.  Please make a signature with all your systems specs including make and model numbers.  I hate guessing at solutions and I'd hate to see you buy any more unneccessary parts because of lack of information.

  • System D.O.T automatically why? problem please help me

    hello everybody,
                           please help me my system says at post message that wrong cmos information then gives me option to boot or go to bios when i check my bios , my ONBOARD LAN GETS ENABLED AUTOMATICALLY  ,the Frequency tab i check says something like PRIVATE DOT ENABLED AND CPU+AGP SOMETHING i mean my comptuer gets fast and the CPU fan becomes on full speed and i hear loud noise until Corecenter runs it becomes quiet again. the question is is this a bios fault or something , DID ANYBODY WHO BOUGHT 865PE PLATINIUM BOARD EXPERIENCE THIS PROBLEM PLEASE HELP ME MY CONFIGURATIONS ARE BELOW
    PENTIUM 2.40 GHZ PRESCOTT (54 C MAXIMUM)
    MSI 865PE PLATINIUM BOARD (IT GOT NO RAID ABILITY)
    DDR 400 MHZ KINGSTON SINGLE CHIP RAM (ALTHOUGH IT RUNS AT 333MHZ)
    MSI GEFORCE FX 5200 T128 (64 BIT DAMN IT!!!)
    MSI CD ROM
    SONY FLOPPY
    COMPUTER CASING WITH SMALL MINI ADDITIONAL FAN ON THE SIDE (IT RUNS MAYBE AND ALSO GIVES ELECTRIC SHOCK OR SOMTHING SOMETIMES)
    STABIMATIC 500V AUTOMATIC STABILIZER(ALTHOUGH I HAVE UPS CAN SOME BODY TELL ME IS UPS ALSO STABILIZER OF APC(AMERICAN POWER ----)
    AMI BIOS 3.4
    SO CAN ANY BODY TELL ME IF THIS IS A PROBLEM OF BIOS SHOULD I UPGRADE TO LATEST
    WHAT METHOD THROUGH AUTOUPDATE OR MANUAL , I ONLY ONCE DID MANUALLY ON MY DELL 4100 PIECE OF CAKE !

    Hi,
    Go to here for MSI LIVEUPDATE
    http://www.msi.com.tw/program/support/software/swr/spt_swr_detail.php?UID=556&kind=1
    Install and run program.........
    BIOS problems:
    http://www.msi.com.tw/html/support/bios/note/boot.htm
    If you would like to download bios and install........
    http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=556&kind=1
    You can also choose 3.7 if wish too first.....
    I am sure this will help you.
    Del

  • I'm in trouble, my iPod Touch is giving 4th shock when recharge and the battery does not last any more. who knows or has a similar problem, please help me. Note: all this after I downloaded the new version OS5.

    I'm in trouble, my iPod Touch is giving 4th shock when recharge and the battery does not last any more. who knows or has a similar problem, please help me. Note: all this after I downloaded the new version OS5.

    I would make an appointment at the Genius Bar of an Apple store because of the shock issue. I doubt it was caused by the update.

  • I am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

    i am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

    Did you check your security software (firewall)?
    A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
    Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
    See:
    * [[Server not found]]
    * [[Firewalls]]

  • 990fxa gd80 raid 0 problem please help me i am begging you

    so i will start with my set up
    990fxa dg80 mb
    fx 8350 cpu
    780ti
    8 gig of ram
    256 hdd
    2x samsung 850 evo
    750 hybrid drive
    So at this stage all my data is on the 750 hdd and the disk is stored away. my problem started with me buyng 2 mx100 256 ssds . If my bios is set to ide or ahci they work fine i had my windows instaled on 1 of them all woks fine. Once i switch my bios to raid ( before i set up my raid 0) boot up win 7 instalation i do not see any drives ( i know is normal) load the drivers for the raid controler (sb950 for w7 as it says in themanual) and only my 256 hdd shows up but not the ssds . Than i set them up in ld raid 0 same problem . Tryed on another 2 mbs ... 1 same and a gygabite same problem. So i was sure there is a problem with ssds. I got rid of them got 2 new 850 evo 250 gb same problem. please help me i am so desparate i am willing to pay woth body organs for help

    I..have a few questions...
    1. You set BIOS to the RAID mode, and under that option there's a Board SATA RAID ROM, do you set it as Legacy ROM?
    2. Did you enter Ctrl+F to initialize the drives/Delete Array(If they're used SSDs) and create RAID0?
    3. Is your Win7 64 bit or 32 bit?
    4. I assume it's 64 bit, did you copy the W764 folder for driver loading?
    And make sure you get the driver from here:
    http://www.msi.com/support/mb/990FXAGD80.html#down-driver&Win7 64

  • Strange audio problem please help!

    Hi, I was recording audio with Logic and a usb audio interface (m-audio). Then, I unplugged the usb cable and I selected to use core audio. I closed Logic. I noticed that the volume controls (up and down) are no longer available and inside sys pref. there's optical out selected (the only available). There's also a red light coming from the port (I'm assuming is the optical out). If I plug in the hearphones everything works fine. What can I do in order to have audio played from speakers again?
    Please help!

    Update: I followed some instructions I found on a blog and I managed to solve the problem. I inserted a paperclip inside the jack output port and I pushed it for a while. Suddenly, inside sys pref. the output changed from "optical out" to integrated output. It's very strange, anyway I think it's a good idea to go to my Apple Store to check if the soundcard has some problems... The MacBook is still under warranty so...
    Any comment would be appreciated, bye!

  • Please help after updating my iphone 4 to ios 5.01 I cannot make phone calls or receive phone calls anymore. I am so annoyed first battery and now can't make calls!

    Please help after updating my iphone 4 to ios 5.01 I cannot make phone calls or receive phone calls anymore, please help, I am so annoyed first battery and now can't make calls!

    The same thing is happening with my wife's iPhone 4 and we can't figure it out. When placing a call, the screen freezes and she needs to restart the entire phone.
    She upgraded to 5.01 this morning over the air while it was plugged in. Immediately afterwards, this problem started happening. We've tried restarting the phone several times and plugged in to iTunes but there's nothing she can do do to fix it.
    Any help is greatly appreciated!

  • HT4623 please help me update ios 4.3 in iphone 3g

    please help me update ios 4.3 in iphone 3g

    You can't. The iPhone 3G can only go as high as iOS 4.2.1. It hardware does not suport a higher iOS.
    BW this is the iPod touch forum.

  • My iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: "unknown error (36), i´ve tried to do lot of things but i can´t  solve my problem. please help!!

    my iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

    Hi, i had the same problem. Try to find the file "apple" or "itunes" don't know it anymore exactly. Ahm well you need to delet any information or just plug in your iphone into an other computer. important is that your iphone never has been pluged in this computer before. This was what i did, and it worked!

Maybe you are looking for