Msi R7770 power edition 1GD5/OC dual monitor advice

Hi guys
I'm hoping someone can assist me. I have the msi r7770 graphic card installed on my pc. I would like to set up my first dual monitor display, but I am unsure what cables I need to connect two screens with and which two of the three ports on the graphics card to use.
Can anybody offer me some advice.
Peter

ok the card has 3 ports! any 2 of the 3 in combination should be perfectly capable of outputting a dual monitor setup!
DVI-I - thats the blue one and has digital and analogue pins
HDMI - Standard HDMI connector
Display Port - High Bandwidth Display signal output
usually with a card like that the best way to hook up 2 screens is 1 to the DVI-I and one to the HDMI port but if one of your monitors has a display port in on it use a display port cable as that port has much higher signal output bandwidth!
its hard to say what the best way is unless we know what monitors your planning to use?

Similar Messages

REQUEST UEFI GOP VBIOS R7770 Power Edition 1GD5/OC

Please, can some on provide me with the UEFI VBIOS for my graphic card model! Thanks in advance!
Link BIOS: dl.dropboxusercontent.com/u/37776896/Cape%20Verde.rom
S/N: 602 - V271 - 05SB1205069114

Please be aware that this is a Users-to-Users Forum and we aren't here for your personal service so answers may take time. There is also no guarantee that you get an answer within 24h or at all.
In this case you're lucky. Use the attached.
Decompress the provided .rar archive with Winrar: http://www.rarlab.com/download.htm
Create a bootable usb stick (https://forum-en.msi.com/index.php?topic=165175.0).
Then unpack the previously provided archive (TV271MH_130.rar) and put the included file (TV271MH.130) on that stick.
Rename TV271MH.130 to 130.rom. Put the atiflash.exe also included in the archive provided on the USB stick too. Now boot from the stick.
Type atiflash -p -f -noaper 0 130.rom [ENTER] and let it flash the vbios.

[Request] UEFI GOP VBIOS for MSI R7750 Power Edition

Hello, I need a GOP/UEFI Vbios for MSI R7750 Power Edition.
S/N: 602-V271-08SC1208010276
ROM: goo.gl/tphw4h
(Temporarily I have no permission to post a http link, so I had to give a shorten one.)
Regards!

here it is
for flashing: http://www.techpowerup.com/downloads/2306/atiflash-4-17/
flash syntax from pure DOS, after booting from bootable USB key:
atiflash -p -f -noaper 0 xxx.rom [ENTER]
where "xxx.rom" will be your vbios file which you want to update

PC suddenly restarts while playing games MSI 660Ti Power Edition OC 2GB

Hi,
I have the following problem since I replaced my graphics card (before 9800GTX+, now MSI 660Ti Power Edition 2GB) I got 3 random restarts while playing games. The computer is not overheating, the CPU's temperature is around 58-59 degrees after running prime95 for 3 hours. The graphics card temperature is 70 degrees after running furmark for 1 hour, the stress tests never failed, just when running games. The computer has been stable. For case cooling im using (2X12cm front, rear 1X14cm below 1X12cm and above 1X12cm +1 X14cm).
I got two random system restarts while playing Doom 3 BFG and one system restart after playing Wolfenstein for 4 hours. The PC just restarts itself.
What could be wrong? I have no more ideas? Should I replace the CPU cooler (im running the stock CPU cooler but all stress tests dont show overheating?!)
Is it possible that the PSU is the reason, but it should be strong enough ...
The system:
GA 870A-UD3
AMD Phenom II 1090T (cooler box)
MSI GeForce 660Ti Power Edition OC 2GB
12GB RAM (12GB Kit 3X4GB DDR3 Kingston Genesis 1600)
Samsung 256GB 840pro
WD Blue 500GB
Thermaltake Thoughpower Q-Fan 750W PSU
Housing NZXT Source 210 Elite
OS: Windows 7 Ultimate 64-bit
Thank you.

The temps for the graphics card are quite normal. I have the same one and under load it will go to 70 to 75C, depending on ambient. What Nvidia driver are you using? Did you do a new driver installation?
If I look at your CPU though, then you are very close to the max CPU temp and throttling may invoke the shutdown http://products.amd.com/en-us/DesktopCPUDetail.aspx?id=640&f1=&f2=&f3=&f4=&f5=&f6=&f7=&f8=&f9=&f10=&f11=&f12=
62C is max.
Could also be your PSU that's not completely stable and continuous power draw may cause Overcurrent or overtemp protection. Speculating here as to probable causes.
Another possibility is your RAM. That should normally be paired in 2's. Have you tested with only 2 modules ? Remember we don't support that MB here, but its just another test I would run. But you would know, probably having run it like that with the previous GPU.

MSI 670 POWER EDITION SLI HELP!

Okay so i recently bought another MSI 670 Power Edition card. I loved my original and wanted a bit of a performance boost.
I run a MSI Z68 GD80 G3 mobo with i7 2600K. 16GB of Corsair Vengeance memory.
So after a few days of testing i get about 10-20fps increase in certain games. Now after comparing my PC to other Computers with similar specs and my cards are faster than theres.
I am not getting that much of an improvement as i should.
On unigine Valley "Everything max at 1920x1080" i get a score of 2333 thats with both cards. To me that seems rather low or am i being silly. Also i was watching a video of a guy running the Metro Last Light benchmark and he was hitting over double what i had in terms of FPS.
Then i read that it could be because i have a sandy bridge and it doesn't utilize PCI.E 3 correctly. Any help would be awesome THANKS :D

Quote from: rydek on 14-July-14, 02:34:20
I run a MSI Z68 GD80 G3 mobo with i7 2600K. 16GB of Corsair Vengeance memory.
Then i read that it could be because i have a sandy bridge and it doesn't utilize PCI.E 3 correctly.
As flobelix stated before, you are limited to PCI-E 2.0 because of your Sandy CPU.
Talking about bandwidth, SLI with PCI-E 2.0 x8-x8 is the equivalent of PCI-E 3.0 x4-x4.
Not very good, but not very bad either.
Quote from: rydek
unigine valley sli - 2349
unigine valley single original card - 1718
Tomb Raider Tress FX off everything Ultra average FPS 62.7 - SLI
Tomb Raider Tress FX off everything Ultra average FPS 36.3 - Single GPU original
Your scores are ok.
With a better CPU (i7 3770K), the scores are around 2200 (single) and 3000 (SLI).
Those with higher scores have overclocked GPUs (and CPUs).
Tomb Raider is one of those few games with great SLI scaling (most of the games are not).
As you can see, you get a 70-75% boost in this game.

MSI GTX570 POWER EDITION helppp

Hi, I just bought my MSI GTX570 POWER EDITION from amazon. And it seem to be some problem about this card. It runs poorly on the 3d mark11. And on starcraft2 it recommend the setting to only "meduim, suggested for 258VRM" but aren't the gtx570 is equipped with 1280VRM. Is there something wrong with my card? I have updated all the newest drivers already.
3d result http://3dmark.com/3d...8UuRNSxXxfNyXL9
print scr http://tinypic.com/r/xm5wz8/7

Quote from: freshlemon on 26-August-11, 12:27:02
it says, "Your Score is Low Compared to Similar Systems.
There may be a problem."
is there anything i can do to improve the performance?
It's not low, as you can see the most people with the same card has the same scores and they are into the same big graph as you
Quote from: freshlemon on 26-August-11, 12:27:02
is there anything i can do to improve the performance?
Overclock CPU or install fastest CPU or OC the GPU further or both

MSI 7750 Power Edition OC.. Overheating .. please help.

i bought msi 7750 power edition. it's idle temp remains constant at 39` and while playing games like darksiders, temp reaches 79` even with moderate or low settings. the fan on such temp reaches max speed .. 99% and makes it really noisy. is the temp normal or is there any defect wid my piece ? .. Please Reply

Temp is absolutely normal under load. Anything below 9ß°C is nothing to worry. Try using Afterburner (>>How to use MSI Afterburner<<) and start Kombustor out of it to check tempa under maximum load.

MSI GTX660TI Power Edition problems

Hi all,
I have a problem with Battlefield since I have installed my new GPU the MSI GTX660TI Power Edition.
I have a Acer Aspire i7, with 6GB memory and a Corsair GS 800W, Windows 7 Home Premium
Since I have installed my new GPU my game freezes and my systems tells me that there had been a problem with the Nvidia Windows Kernel mode and that it has been restored.
It happens with both BF3 and BF4....while typing this topic message the same thing happens.....
It also says Directx error....but I have the latest drivers....
Could it be the Bios, mainboard or is my GPU not working as it should?
Thanks for your help.

List full system specifications, read >>Posting Guide<<

MSI N560GTX-Ti Hawk PerfCap with Dual Monitor setup

Hi guys,
as far as I'm concerned, there shouldn't be a PerfCap when running a setup with two monitors on extend desktop setting, am I right? However, my GTX560-Ti does PerfCap and sometimes even does this while gaming (which is incredibly annoying). The only way to get it to clock up again is to reboot my PC.
My question is, why is that and how can I get rid of this behavior? I already tried updating the VBIOS but it didn't help.
Thanks in advance
Monsterkater

I'm sorry, I thought "PerfCap" would be a known term.
As the title states, it's a MSI N560GTX-Ti Hawk. The Card is clocking down, GPU-Z reports "PerfCap Reason: Util" which is, according to Google Search, because it isn't challenged enough. However, when running a dual monitor setup it should (again according to Google Search) always run at the default speeds (950/1050/1900 Core/Memory/Shader). I have updated my signature to show my system details as listed in the Posting Guide.
The temperatures under load are okay, the highest I have seen was 76°C GPU, 74°C Memory and 69°C VRM (all of them measured with MSI Afterburner). I have tried several drivers including Beta drivers and always checked "perform a clean installation". I also tried updating the VBIOS. I didn't know what else to try because Google Search doesn't yield much results for this.

MSI R7850 POWER EDITION 2GD5/OC vs TWIN FROZR 2GD5/OC

I had to do an RMA with MSI for the R7850 POWER EDITION 2GD5/OC I had, and it turns out they don't have anymore inventory of it, so I'm accepting a R7850 TWIN FROZR 2GD5/OC as a replacement.
The only differences I can spot immediately are that I may lose voltage control, the Core clock comes slightly lower, and the heatsink is model III instead of IV.
I imagine I can just overclock with Afterburner if needed to up the core clock; I'm wondering if voltage control could also be unlocked though? Also is there any other difference that I should be aware of?

general difference between Power Edition and models with Twin Fozr,
is that Power Editions has Enhanced PWM Design and offers triple voltage control [compared to regular model: + memory voltage and + Aux voltage]

Dual Monitor Advice

I have two monitors, one a Lacie 20" 1600*1200 which is designed for photo-editing and the other a 1600*1050 Samsung. Both are color calibrated. I'm new to Lightroom, currently trying V3 which i like a lot.
What I'd like is, does anyone have wide experience of dual monitors with light room and have a favourite setup for the LR3 panels? I'm thing that I'd view and edit images full screen on the Lacie. Any thoughts or ideas?

There's not a lot of customisation available in LR, sadly so LR is not able to take best advantage of the extra screen.
I often have grid on second screen and main image on Develop screen as you cannot do it the opposite way around like you can in Library mode, which would be my preference as it uses the space better. But I do also use a second larger image on panel free second screen as well at times too when developing. So you can have both panels out in develop and fill screen with image on second monitor - it also updates to reflect crop you are trying out on main screen when using crop tool, which is handy.

MSI NX8600GT-T2D256E OC/D3 with Dual Monitors

Hi Team
I am new in this forum please forgive me if I have break any rule (as I was not sure if to post this direct or search for FAQs)
I got the above Graphics card in my Vista 64 bit dual core machine, which was workling fine since more than 3 years. But recently i purchased Sony Bravia 46 inched full HD TV, and have plugged to my system as second monitor to watch movies and so using DVI to HDMI cable to one of HDMI slot on TV. I am using the Left DVI (when facing towards rear of the VGA card) slot to TV and Right one to my 22 inches existing LCD Monitor.
After each reboot I will have to select the resolution to Sony 1080p Native from the NVidia control panel along with HD input Audio enabled with 60Hz. Bye the way I haven't received SPDIF cable though, but I don't care as My PC is sitting next to TV and I have very good PC speakers. Anyway when i reboot the PC the BIOS screen appears on the TV and then the rest of the process happens on the standard monitor. then both monitor and TV seems normal, with all desktop icons on the Monitor with my chosen screen background, and same screen background on TV but without any desktop icons. The key thing is the display size on the TV displays only in the middle of the TV with diagonal size of about 40 inches diagonal roughly, and in order to bring this normal I adjust the TV resolution to native. Today at one stage I lost the colors on the main LCD monitor turns in to monochrome. Then system restore fixed the issue.
So my question is, is this normal?
Am I missing anything here?
Do I need to update the hardware/software, if so which model/version will support.

"Can you suggest any software program which would test the psu?"
You can't test PSU with software, but only with PSU replacement. Probably your cheap PSU is defective or weak.
Also read the links:
Quote from: BOSSKILLER on 30-July-08, 22:39:56
>>> PSU's---2 x 12v---The Dual Rail Myth <<<
>>> Is your problem caused by your PSU? <<<
For good PSU suggestions:
https://forum-en.msi.com/index.php?topic=112039.msg836246#msg836246

MSI 670 Power Edition -- need to disable the Dust Removal

I just bought a 670 PE and I wish to disable the dust removal because, having a filtered case that's quite free of dust, it is of no benefit to me and only an annoyance (my system is very quiet, having the fan spin that loud is ridiculous).
It sounds like in the past there was a BIOS on the German website that did this, but I no longer see it there (I tried the one that is listed in the BIOS section there and it does nothing different).
Does anyone happen to have that particular BIOS? Very surprised that MSI does not officially provide this.
Also while I'm at it, has anyone solved the issue with these cards throttling when overclocked? Changing the power limit seems to do nothing. I'm pretty sure it's a BIOS issue.

Quote from: rydek on 14-July-14, 02:34:20
I run a MSI Z68 GD80 G3 mobo with i7 2600K. 16GB of Corsair Vengeance memory.
Then i read that it could be because i have a sandy bridge and it doesn't utilize PCI.E 3 correctly.
As flobelix stated before, you are limited to PCI-E 2.0 because of your Sandy CPU.
Talking about bandwidth, SLI with PCI-E 2.0 x8-x8 is the equivalent of PCI-E 3.0 x4-x4.
Not very good, but not very bad either.
Quote from: rydek
unigine valley sli - 2349
unigine valley single original card - 1718
Tomb Raider Tress FX off everything Ultra average FPS 62.7 - SLI
Tomb Raider Tress FX off everything Ultra average FPS 36.3 - Single GPU original
Your scores are ok.
With a better CPU (i7 3770K), the scores are around 2200 (single) and 3000 (SLI).
Those with higher scores have overclocked GPUs (and CPUs).
Tomb Raider is one of those few games with great SLI scaling (most of the games are not).
As you can see, you get a 70-75% boost in this game.

BIOS Update for the MSI GTX670 Power Edition Card

There is a Bios update for the MSI GTX670 PE video card but it's for a hybrid card. What is meant by a hybrid card and how do I know if this applies to my video card? Any help would be appreciated in advance. Thank you. I do know that I can't for some reason or another install the Msi Update program for this card. It keeps saying that you have to be the administrator and Iam the administrator on my system. I do not understand.

You can use windows version of it to flash it:
>>Download NVFLASH for windows<<
syntax from cmd:
nvflash -4 -5 -6 myrom.rom [ENTER]
where myrom.rom will be your vbios file

MSI R7770 GHZ Edition Screen Resolution Reverts

My Screen Resolution sometimes reverts to 1024*786, when PC starts. It doesn't happen every time, but once in a day or 2-3 days after. My recommended resolution is 1600*900.
Using latest version of graphics driver 13.12, downloaded from MSI official website.
I have tried uninstalling & re installing. Then formatting & fresh install. But no luck. Please help me regarding this matter.
Thanks...

A Radeon 7770 requires 19A on +12v and a 500W psu minimum what makes your psu inadequate. That on the other hand is not the only problem. This old Fujitsu PC lacks an updated bios for supporting new vgas especially as new like the 7770. Also it is an old PCI-E Gen1 board AMD Gen2 or Gen3 cards usually cause trouble with or refuse to work at all. To sum up the possibility to run the card in your old Fujitsu PC is very slim or there's even none.

Msi R7770 power edition 1GD5/OC dual monitor advice

Similar Messages

Maybe you are looking for