Msi r9 290 showing 3072 memory only on afternurner

hi when i use msi afternurner, on my cpu usage when playing games, it says it only uses 9 or something and also i can only see 3072mb of memory out of 4gb... is that right? anyone?

i also noticed this for another msi user with the same card,
this is something particular down to the afterburner, because only this one shows 3GB instead 4GB
don't have a answer for you why is this,
but you can ask either here: http://forums.guru3d.com/forumdisplay.php?f=55
or here: >>How to contact MSI.<<

Similar Messages

I have installed 20GB memory - Only 16GB / 13GB showing in Premiere Pro - Any Help? (Specs and pics below)

I have installed 20 gb memory - Only 13 gb showing in Premiere Pro - Any Help?
(Windows 7 64 bit - Quadro 4000 card - 20gb DDR3 PNY RAM) I doubled Checked with SPECCY that something wasn't amiss

Thanks much cc_merchant
Quick question - would this memory problem still cause a lag in project playback? I have some pretty hefty HD .avi after effects and a few places where there are up to 9 video frames in one window. But I was watching a Terry White video and he said the lag should be gone with a Quadro Video card and CUDA enabled.
I also occasionally get this card is not enabled for CUDA and I have to restart PP

Why is 8gb only showing total memory of less than 6.5?

why is 8gb only showing total memory of less than 6.5?

Because the difference is due to the operating system taking up most of the diference and the other is how GB is advertised and actually used.
http://en.wikipedia.org/wiki/Gigabyte

MSI Twin Frozr 7970 3gb OC showing weird memory?

Hi there, just wondering if this is a common issue, but in things like the Blizzard System Spec Beta program, and the Benchmark test for Final Fantasy 14, it shows that my video card is 2765mb, but it's a 3gb card.. not too sure what's going on here. In Catalyst Control Centre, it shows it as 3072mb.

since Catalyst shows correct memory size is fine.
you can check it with GPU-Z and others
Quote
but in things like the Blizzard System Spec Beta program, and the Benchmark test for Final Fantasy 14, it shows that my video card is 2765mb
they could read it in error or to show the available/free [not total] memory instead

MSI P35 Neo2 Fir Patriot Memory Problems.

Hi,
Having problems with my Patriot Performance PC2-6400 Low Latency Memory DDR2 (800mhz) 4-4-4-12, 2,2v, 2 * (2gb(2*1GB)kit) =4gb total
on a MSI P35 Neo2 Fir moderboard with Intel Q6600 cpu)
When i check the memory with CPU-Zv1.44 the memory only goes with the frequencys of
DRAM Frequenzy 399.5mhz
FSb : Dram 2:3
Cas# latency 5.0 clocks
Ras# to Cas# delay 5 clocks
Ras# Precharge 5 clocks
Cycle Time 16 clocks
Why doesn't they go in 4-4-4-12 frequencys ???
Have tried to manually change dram timing in bios but no success
so i went back to auto dram timing.
What can i do to get the 4-4-4-12 timings.
Please help.
thanks in advance swefin

Quote
When i check the memory with CPU-Zv1.44 the memory only goes with the frequencys of
DRAM Frequenzy 399.5mhz
~400 MHz is the correct frequency for your modules. CPU-Z shows real clock speed. DDR means Double Data Rate (two transactions per clock cycle). Multiply 399.5 MHz by two in your head and you have your effective DDR(2) rating of 800 MHz. There is no problem here.
Quote
Why doesn't they go in 4-4-4-12 frequencys Huh
Have tried to manually change dram timing in bios but no success
so i went back to auto dram timing.
What can i do to get the 4-4-4-12 timings.
CL5 is the standard latency for DDR2-800 modules. It ensures that they are able to operate @JEDEC standard voltage settings @1.8V (+/-0.1V). The board is supposed to set memory timings to CL5, otherwise your system would not be able to boot at standard voltage. Check the "SPD" tab in CPU-Z and look for the standard timings that were programmed into the SPD chips of your modules (400 MHz), I am absolutely sure that you won't see 4-4-4-12 @400 MHz @1.8V being part of the SPD tables.
You have to manually adjust memory timings in BIOS to 4-4-4-12 AND also increase memory voltage to the value the manufacturer recommends for CL4/DDR2-800 MHz. The voltage is usually 2.0-2.2V depending on the brand and type of RAM in use.

Can we conform in memory via in memory only query?

Can we conform in memory via in memory only query?
In other words, if I do in memory query only, does the query result will represent changes done in the UOW so far?
I thought that was the case, but then I saw this comment in EclipseLink 1.1.3, class ReadAllQuery:
// PERF: Fixed to not query each unit of work cache (is not conforming),
// avoid hashtable and primary key indexing.
// At some point we may need to support some kind of in-memory with conforming option,
// but we do not currently allow this.

We want to be able to do conforming against session via uow so include state in uow, and also only against uow.
Please show us how it can be done using existing API.
Scenario 1:
We have 1000 organizations loaded in the session cache, we always cache all of them, so we know we don't need to hit the db. So we would like to do query in memory via UOW to pick-up the cases we are in the middle of a transaction modifing/creating/deleting an organization and also get the session object not yet transfered to the UOW.
Scenario 2:
I do not want to flush before each query, it is a popular query. The class queried against have many thousands objects in the session cache, also there is no garanty the objects are already loaded. I send to the db the query truncating all the columns of the select except for the primary keys columns, so using report query asking for primary key only. I then verify if the objects are present in the cache, if some are not present, I retrieve the missing objects in batch from DB using the ids. Most of the time we have 100% cache hit. Then I transfer all the objects to the UOW. Then to get modification done so far in the transaction, I query in memory only in the UOW not accessing session cache because would have to iterate thousands of objects. That sound convoluted scenario but it's actually very useful in our application to get better performance without introducing stale issue. Similar scenario is that we have some query that are repeted many times during the same UOW. We can keep trace that the query have been executed one time against the DB, so that the result is loaded in memory. But then, we still need to execute again to pick-up the change in the transaction but we don't want to pay the price of iterating the many thousands instances in the session cache, when we already know UOW has all the objects that the query needs.
Thanks for helping us to leverage query in memory, an exclusive feature of TopLink/EclipseLink.

My 5130 XM shows Low Memory.

Hi,
My 5130 XM shows low memory on phone. It only shows 4 mb actual memory is nearabout 25 mb. I had updated firmware version which i think was 6. Now it is 7.
For reliable working i deleted most of my phone ringtone. How i can get back my phone "origional nokia factory based setting"?
Moderator Note: Personal contact details removed. It is unwise to publish personal contact information on a public web forum.

Have you ever created a buck up of your phone. If you have one you have to restore it. Otherwise you have to install your phone software .

Overclock my msi r9 290..

the msi r9 290 comes with a stock 977 mhz.. if i OC it, up to how many should I put in order to have work stable... the core clock and memory clock...
or should i just stay with what I have...

Try OC mode.
If you want more:
Set Gaming App to game mode (default clocks).
Run few different benchmarks and record GPU clock it states there, mem clock and temperature.
With Afterburner add +10 to mem clock and re-do the above (benchmarking, temps, clocks). If it dont crash, make note that memclock on +10 didnt crash. Rinse and repeat until crashes on mem clock, for example +93 didnt crash at all within few benchmarks but 94 did.
Then proceed to GPU clock with same technique: small rise, test for crashes, record clocks and temps, repeat until you find crash point, and go slightly lower until it dont crash.
Mind the temps! If your gpu without OC hits 70C, then max 5C will be safe to go. If hits around 60, then even 15 should be ok ! Keep it under high 70s/low 80s under load

MSI R9 290 Gaming 4G 4GB Performance/FPS

Hi everyone,
i bought my new pc. And i just assembled everything.
Main Board: GIGABYTE AM3+ GA-990FXA-UD3 (990FX/ATX)
Bios Version: F2
Video Card: MSI R9 290 Gaming 4G 4GB
PSU: CS Series 80 PLUS Gold CS650M 650W Modular
12v rail Rating of listed PSU: ATX12V v2.4 ed EPS 2.92 (i dont know how to check)
CPU: AMD FX-8320E AM3+ EIGHT-CORE 4.0GHZ 95W 16MB BOX
Memory: DDR3 1600Mhz PC12800 16GB Corsair Vengeance 1.5V CL9 (4x4GB) (X79)
SSD/ HDD: Samsung SSD Serie 840 Evo Basic 250GB SATA III
CPU COOLER: Original one
Raid Card: main board
Sound Card: main board
Any Additional hardware plugged into your system:
OC: (Yes / No) sometimes
Operating System: Windows 8.1 Pro 64-bit (6.3, Build 9600)
i can also give you dxdiag if you need it.
i would like to check if i assembled everything fine, and it works as it should do. How can i test this video card?
I played Diablo 3 with a friend of mine and compering his fps with the same video settings my pc has lower fps then his pc. And my pc is much better.
Probably Diablo 3 is not the best game for test everything, but maybe is just a signal that means that something is going wrong
thanks for your answer and attention.

Quote from: flobelix on 07-March-15, 22:45:45
You can inrease gpu clockrate in little steps with >>MSI Afterburner<<. If it gets unstable reduce clockrate by a step until it is stable again. GPU will have better performance as long as it is not bottlenecked by the cpu.
i dont get it..with this u mean that i need to increase gpu or cpu clockrate? how should i set afterburner?

MSI R9 290 Gaming - My PC keeps freezing, blackscreening and then rebooting?:(

So for christmas i got an r9 290 and a new 750w psu.
Before instaalling them i had never had any problems with restarting. However now that i've installed them my PC keeps restarting? what have i doneeee?
My components are;
coolermaster 750w 80+ bronze psu
ASUS m5a78l usb 3 mobo
AMD fx 6300 cpu
Msi r9 290 gpu
three fans
1 hdd
2 x 4gb ddr3 ram
What is wrong with my PC? it surely cant be power as coolermaster said i only need about 450w!
When I first installed it this morning it was working fine for a few hours then this all happened! I've made sure all the psu connectors are in properly. Just put my old gtx 650 in and that worked fine i've been able to play games?

Quote from: nhornbrook on 28-December-14, 21:34:18
I don't think it's the mobo bios because if it couldn't handle the 290 surely it wouldn't let me play any games at all? And the device is recognised?
Compatibility issues due to an outdated bios can cause all kinds of problems including the one you have. As this is also an old low-end board better check for an update. When does your pc restart? under load or even in idle? If under load what games did you test?

MSI R9 290 Gaming OC Edition Hybrid Bios

Hi, there!
I have this brand new MSI R9 290 OC installed on my good old 990FXA-GD80. Works fine on BIOS key on position 1, but no info on the position 2 and games remain black screen, playing only audio. Sometimes Blue Screen on startup when enable Windows 8 feature and Secure Boot.
I believe it has the latest vbios, but I cannot manage to have a copy of it...
Here is the Legacy version:
[Inline mode=1]
The serial number is: 601-7640-120B1401012161
I would like you people to provide me the .rom file so I can try flashing the UEFI version of the same vbios over the position #2.
I would appreciate the help and attention.
(Sorry for the poor English.)

here it is 1C0_TV308MH.rar (97.14 kB - downloaded 13 times.)
flash guide:
Quote
Decompress the attached .rar archive with Winrar: http://www.rarlab.com/download.htm
Create a bootable usb stick (https://forum-en.msi.com/index.php?topic=165175.0).
Then unpack the previously provided archive (xxx.rar) and put the included file (TVxxxxx.zzz) on that stick.
Rename TVxxxxx.zzz to zzz.rom.
Put the atiflash.exe from: https://www.techpowerup.com/downloads/2306/atiflash-4-17/
on the USB stick too. Now boot from the stick.
Type atiflash -p -f -noaper 0 zzz.rom [ENTER] and let it flash the vbios.

Is it possible for someone in the UK to gift me, someone in the US, a show that is only available in the UK?

I'm pretty desperate to watch this show that is only available in the UK iTunes Store. Is this a plausible solution to my problem, since I live in the US and can't make purchases from the UK store?

Sorry... Not possible.

SharePoint 2010 List View Web Part not showing for read-only users?

Hello all,
I have List View Webparts on my Blank Web Part page, and it's not showing for Read-Only users.
Is this intended by Microsoft or is it a bug?
Thank you!

Hi,
According to your post, my understanding is that the read only user could not see the list view web part.
Per my knowledge, the issue may be cause that the user do not have the proper permission for the list.
1. Check whether the user can access the list.
2. Check whether the user can view all the items instead of partial items in the list.
3. Check whether there are some fields refer to other lists or terms, especially the lookup field or managed metadata filed.
If that is the case, make sure the user can access the lookup list.
Thanks,
Jason
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Jason Guo
TechNet Community Support

As a writer I'm using Pages to write my documents but the title shows up on every page. How do I set-up my page so that it shows up on only the first page?

As a writer I'm using Pages to write my documents but the title shows up on every page. How do I set-up my page so that it shows up on only the first page?

Don't put it in the Header.
Peter

I recently bought an Ipod touch 2nd gen, (Ebay). It's in great shape and seemed to be wiped clean. When I connect (via windows computer) to Itunes with usb cord the Ipod icon shows, but the only function you can do is eject. When its in the upper right h

I recently bought an Ipod touch 2nd gen, (Ebay). It's in great shape and seemed to be wiped clean.
When I connect (via windows computer) to Itunes with usb cord the Ipod icon shows, but the only function you can do is eject. When its in the upper right hand corner and you click on it all you get is a done button, when it's in the side bar right click and your only option is eject, left click has no effect. If I go to "file">devices it's as if there are no devices connected.
I purchased a song with Itunes on the Ipod itself, and it transferred to my library on the computer automatically .
I have an Iphone 5 and a nano that are still functioning with Itunes thru computer so I'm thinking the issue is with the Ipod touch. I've reset it several times, rebooted it, with no change.
nothing on the internet has helped, I called tech support and got disconnected. Should I take it to a retail store? I just don't know where to go next, I'm of course willing to pay for tech or repair. looking for suggestions.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Msi r9 290 showing 3072 memory only on afternurner

Similar Messages

Maybe you are looking for