MSI R9 290X triple level signal not working?

The lights do not change colors on the lightning emblem, any thoughts?
I am also having a problem with the vga fan control software not showing pwn temp or speed for the middle yellow fan?
I also cannot figure out if I need a bios update?

Hopefully I do not have that GPU killing fan problem with the other two big side fans on it that I hear some have had from newegg reviews. The fans all run great and kick up to about 50% on full load at 60C (it's cold here) . The other cards that have the problem killed their GPU's because the side fans would only stay at 25% no matter what the temp of the GPU was from what I am hearing (although it could be the PWM temp frying). The vga fan control software works (from what I have seen from various videos and demos) with all three fans and the PWM/GPU temp showing numbers. The bottom fan (fan 2) slider which controls the middle yellow fan was active. In my vga fan control software the middle fan control is locked and cannot be moved although the side fans can be unlocked and controlled manually. The GPU temp and side fans speed(s) shows but not the PWM temp or the middle yellow fan speed. The fans only go up to 50% at best at a full load temp on the GPU at 57-60C due to the stock fan profile in MSI afterburner. If I go 100% by adjusting the fan curve at 60-70C, the noise is immense and sounds like a vacuum cleaner. I played around with it a bit and got temps down 1-2C by setting a 75% or lower curve at 60-70C. I believe this only controls the side fans and not the middle yellow fan as I cannot read the PWM temp or adjust the middle yellow fan. The card is a MSI Lightning 4GB R9 290X.

Similar Messages

  • Item level security not working when placed in a portlet page

    I have three page links linking to separate pages and have two of them with item level security turned on for specific groups with view privilges. I have the access for those groups with view privilges in the page level as well. I have published that as portlet and placed the portlet in another page which has view priviliges for the groups specified in item level as well.
    But I notice that when i place the portlet in a page, the item level security is not working.
    Item Level Security Not Working for Items Placed on a page and published as portlet and placed in another page. Is there some work around for this.
    Thanks
    Valli

    Would you please clarify for me? Is the problem that unauthorized people can see the portlet, or that unauthorized people can see the links?

  • MOVED: MSI K8N SLi Platinum Duall Channel not work? Please help

    This topic has been moved to AMD64 nVidia Based board.
    MSI K8N SLi Platinum Duall Channel not work? Please help

    Quote from: iggsy on 29-July-05, 06:03:49
    Ok I unerstand but i have 201mhz whay 201 instend 200 ?!
    Mine does the same thing at the startup screen but not on cpuz...go figure.  Just my 2 cents.   

  • Query level filter not working in Webi report

    Hi All,
    I am using BOXI R3.1 (SP3), m facing one problem when refreshing Webi report on daily basis. I am using three query level filter as a prompt, but i checked one filter is not working then i need to reapply this filter and rest 2 filter is working fine.
    Can anyone suggest me why problem is coming?
    Regards,

    Hi,
    Prompts are interactive, and come from the query panel. Filters are not interactive, and are set on the report or block. There are also input controls, which are interactive filters
    1. Select the universe in the list of universes to open the Query Panel.
    2. Drag the Year object to the Result Objects pane.
    3. Drag the Number of Guests object to the Query Filters pane and create a report filter that restricts Number of Guests to greater than n.
    4. Click Combined Query.
    The Combined Query pane appears in the bottom left of the Query panel with the two queries joined by UNION.
    5. Click on the second query and remove the Year and Number of Guests objects.
    6. Drag the Reservation Year object to the Result Objects pane.
    7. Drag the Future Guests object to the Query Filters pane and create a report filter that restricts the future guests to greater than n.
    8. Click Run Query.
    Best Regards
    Naveen

  • Object Level security not working on OBIEE 11g 11.1.1.7

    Hi,
    I am experiencing problems with object level security applied on application role in 11.1.1.7 version. If i create a user and assign that user to a application role and give that application role permission to Access Answers in Manage previleges, it is not working. If i directly add a user to permission list in Manage previleges section then user is able to access the answers. I added that application role in "Access to Answers" section in Manage previleges section. Permission for Authenticated users is denied.
    We recently upgraded from 11.1.1.5 to 11.1.1.7. Please can someone confirm if it a bug in 11.1.1.7 or it is because of the upgrade process.
    Regards,
    Sandeep

    Hello Sandeep,
    I have just verified the below scenario as you said but didnt find any issue.
    I have just created a User, Group and Applictaion Role under default authentication provider . Assigned user under group and group under newly created application role and provided access to answers for new application role under manage privilages and I am able see it.
    This might not be a 11.1.1.7 bug check it from upgrade end.
    Regards,
    Srikanth

  • Row level security not working if I hit the aggregate

    I have applied row level security on presentation layer , however it does not work if the report hit the aggregate any idea on this...

    Hi Ingo,
    Security is set up using /crystal/rls transaction. A custom auth object is used for checking the company code with a single field "BUKRS".
    This custom auth object is maintained for the PA0001 table.
    This object is added at the role level with the restricted access to the Company Code..

  • HP 15 r-150 HDMI no signal not working

    HDMI port not working !!! HDMI no signal!!!

    Hi there @ellocopirates,
    Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel.
    I understand that you are having trouble with the HDMI port on your notebook. I am happy to help with this. Please post the full product number for your notebook. See the following, if you need help with that information.
    How Do I Find My Model Number or Product Number?
    Have you tried a different HDMI cable?  Or tried connecting to a different external device?
    Does the same cable and external device work when connected to another notebook using HDMI?
    Were there any recent changes to your system? Software, hardware, drivers?
    For now, try working through this page.
    HP Notebook PCs - Troubleshooting HDMI Display and Sound Issues
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • MSI GT 72 QE steelseries lights not working

    Hi there .My lights are not working anymore. Yes ,i have the lattest driver installed from msi site ,for wind 8.1 all good in device and printers ,all drivers are installed and working properly if i check them...and still ,no lights .Any idea ?

    Quote from: clement_big_boy on 31-December-14, 00:37:52
    Hi there .My lights are not working anymore. Yes ,i have the lattest driver installed from msi site ,for wind 8.1 all good in device and printers ,all drivers are installed and working properly if i check them...and still ,no lights .Any idea ?
    make sure steel series engine is installed if it isnt then download it and install it then make sure a profile exists as well on program or it will either remain keyboard as off or red

  • MSI GAMING 5 - ALL USB ports not working

    hello
    how are you every one 
    i have problem with rear usb port i can use it in safe mod and bios only but it does't work when the operition system start i try to slove the problem i updated bios i have other pc and same specification and it's work without any problem but with this mother borad rear USB ports not work also the USB ports on the case ALL USB PORTS NOT WORKING
    Mouse and keyborad work in bios but if the system run don't work ! and trun off
    and all usb devices
    in safe mod work 
    rellay i don't know where is the problem !
    CPU : Intel Core i5-4690K
    M.B : MSI Z97 GAMING 5
    RAM : G.Skill Ripjaws X 8GB DDR3 Kit
    GPU : Gigabyte GeForce GTX 970 G1 GAMING
    SSD:Corsair force LX 256 GB
    HARD: Seagate Barracuda 1 T.B 7200 RPM
    CPU COOLER : Cooler Master Hyper 212 Evo
    PSU : Cooler Master GM-Series 750 watt
    CASE : NZXT Phantom 410
     Thank you

    Quote from: Nichrome on 28-January-15, 00:18:47
    Hi,
    What about if you try to install drivers from your product's page?
    http://uk.msi.com/support/mb/Z97-GAMING-5.html#down-driver
    And when exactly it starts to fail to work? Did you try to have OS just installed, restart it and see if it works then? Are you able to determine which driver installation causes USBs to stop working?
    thank you
    i just remove USB3 controller driver and work 
    thank you all :D

  • MSI Z87 GD65 Gaming EIST is not working

    Hi all, my EIST is not working properly, the CPU clock run between 3.7-3.9 all the time (VID 1.153 - 1.219)
    Here is my setup:
    Motherboard and CPU: MSI Z87 GD65 Gaming + 4770K
    OS: Clean installed Win 7 SP1 with most updated driver from MSI site.
    Bios version: 1.2 (All default settings)
    Actually the EIST works before without installing driver ME and chipset driver from MSI site, any advices?
    thanks in advance.

    Hi and welcome,
      to DougQuaid tip.
    Allso if you have OC your system, you need to set Ratio mode to Dynamic and voltage mode to Adaptive.
    Like in this picture of my BIOS settings. I marked those with yellow.
    Warning: After that you shouldent stress test your CPU anymore with Prime95, Occt, or so on programs. Because they could get the MB give too much power to CPU 
    I just tested those (ME and Chipset) files from MSI and still get my clock and voltage down normaly.
    There seams to be new official relice of BIOS 1.3v there too, so you could try that. if yours cot some bug in it.
    Also make sure on task manager that your pc isnt doing anything under. Like live Spybot/virus/... -Scans.
    I hope these help Cheers, Mummy

  • Folder level permission not working

    Hi,
    I have created a user Test_sup and assign few finance roles in BI system.I have imported these users and role to business object system and then i created an Enterprise  group Financial reports and add the Sap roles as sub group and the test_sup is also member of the Financial reports parent group.Now i assigned the user test_sup on a folder called security and assigned the customized access level which i created and removed the folder inheritance.
    Now when the test_sup logs in BI lauchpad he is able to see all the folders as well security folders.But i need to restrict the user by only access to security folder which mean he should only see the folder security and not all folder .
    Pls let me know if i ahd made any mistake above as it is not working .

    Hi,
    So it mean i should alter the standard access level of Everyone.
    Also i am also not able to remove Everyone and Administrator group on any folder .The tab remove is faded.
    Below is the User security of my folder Security
    Administrator
    DB1~100/TEST_SUP
    Everyone
    Financial Reports_test
    Pls clarify

  • MSi GE60 2OE 002US Backlight keyboard not work ?

    Hello everyone,
    My english is not good sorry for that.
    So i bought this laptop and everything is up to date but when i press the button on the top left of the keyboard, the led lights is not work. The latest SCM driver is also installed.
    the bios version is E16GCIMS.516
    EC Version is 16GCEMS1 5.06
    I have check the cable from the keyboard and the small cable ( thats under the hdd ) is good installed to the mobo.
    Please help and sorry for my bad english .

    Quote from: crracer_712 on 22-December-13, 01:22:46
    If this is a new laptop, I think I would either get ahold of MSI for warranty support or return it to the store you bought it from for repair or replacement.
    it is new but it has now no warranty because i have open the under hdd.
    And now i have a another problem. .!
    the battery was at 6% so I went charging.
    it says that the battery is charging but remains at 1%, and if I disconnect the adapter from the laptop, the laptop goes shutdown. 
    Without the adapter the laptop will not open.

  • Row Level Security not working for SAP R/3

    Hi Guys
    We have an environment where the details are as mentioned below:
    1. Crystal Reports are created using Open SQL driver to extract data from SAP R/3 using the SAP Integration Kit.
    2. The SAP roles are imported in Business Objects CMC.
    3. Crystal Reports are published on the Enterprise as well.
    3. Authorization objects are created in SAP R/3 and added as required for the row level security as mentioned in the SAP Installation guide as well. The aim is when the user logs into the Infoview and refreshes the report he should only see data that he is meant to so through the authorization objects.The data security works very much fine when the reports are designed directly on the table but when the reports are built on the Business View it doesnt work hence the user is able to see all data.
    Any help in this issue is greatly appreciated.
    Thanks and Regards
    Kamal

    Hi,
    In order for row level security to work for you using the OpenSql driver, you need to configure the Security Definition Editor on your SAP server.  This is a server side tool which the Integration solution for SAP offers as a transport.
    This tool defined which tables are to be restricted based on authorizations.
    However since you are seeing the issue on reports based on Business Views, you need to identify whether the Business View is configured in such a way where the user refreshing the report is based on the user logging into Infoview.  If the connection to your SAP server is always established with the same user when BV is used then you security definition is pointless.
    You can confirm this by tracing your SAP server to identify what user is being used to logon to SAP to refresh the reports.
    thanks
    Mike

  • Concert level mapping not working

    I've tried  to make my playback controls work on a concert level so I don't have to reset them to each patch. For instance, I tried setting a button to play but it doesn't work. Any ideas?

    Hi
    Where you put the Playback Channel Strips all depends on how you want to work. The basic concept is that at Patch level they will only work in that particular Patch. At Set level they will work throughout that set (with or without additional patches in the same set). At Concert level they are Global.
    You may find it useful to make one Set or Patch with the right number of Playback channels, map the Screen controls, then make copies of the Set/Patch and simply swap out the Playback audio files. That way you only have to do the Control mapping once.
    You could also save the Set/Patch, for future use.
    HTH
    CCT

  • MSI P35 Realtek HD sound driver not working

    I am unable to reinstall the driver nor uninstall it.. The nividia VGA GTS 8800 works great and the LAN works, except HD Audio not working.
    Good thing I got creative sound card and 1 available PCI slot to install it..

    O my P965 Plat I could not install a new version of the driver nor uninstall the old version. Never figured out why but I keep restoring images getting progressively older and found one I was able to uninstall the old driver and then install the new driver. 

Maybe you are looking for