MSI RG300N WLAN-N ROUTER 802.11G+N

Hello,
I'm looking for a Wlan router and come across this MSI RG300N.
It's the cheapest N router around here in the Netherlands, but i can't find much info about the device. ???
what i found:
supports 802.11b, 802.11g and 802.11n
1x RJ-45 (10/100Mbps) WAN poort
4x RJ-45 (10/100Mbps) LAN poorten
3x Antenne
4Mb Flash mem.
16Mb Dram
SPI Firewall
VPN Passthrough
WEP 128-bit, WPA, WPA-PSK, WPA2-PSK
Does anybody have some more info or user experience?
for example how much power does it use? (the eminent em4550 for example only use 5 watts)

Quote from: hjs on 05-February-09, 15:48:54
The specs says the firmware is upgradable, but where can i find new firmware versions ?
(the number of firmware updates says something about the support for the product, more is better )
Where is the firmware download?
Has anyone looked at the hardware? Is this router an Atheros ar9132 with ar9103 radio? If so, exciting news! MSI may have produced a high quality version of the Atheros AP81 platform routers.
If this router is ar9132 + ar9103, it is possible to run OpenWRT Linux on this router. it would be able to use the Linux ath9k open wireless driver and have a bright future. You can see more information at: http://www.google.com/search?hl=en&q=site%3Aforum.openwrt.org+ap81&btnG=Google+Search&aq=f&oq=

Similar Messages

Need help setting up Powerbook G4 to Belkin Wireless G Router 802.11g

Cannot get the laptop to go online, says "the specified server could not be found. Called my internet provider, Belkin and no one can get it online. Can anyone give me the steps to setting up the laptop maybe the settings are not right? I bought an airport card thru ebay and did install the card in the laptop. My signal level is full so looks like the card is working. It does say that the base station id is not available not sure if this would be the problem? Again any suggestions would be helpful, I have had a friend here and look at it also and he could not get it to work. I am using this also with my PC but that is hook directly into the router. Just want to get the laptop so I can surf the web. Thanks!
Powerbook G4 Mac OS X (10.1.x)

When I open the internet connect there is an box for airport to turn it on and off and in the box under signal level there is a blue bar there is no black or grey bars. And I am not sure abt the security on the router how can I find that out. Sorry if I act stupid with this but I am learning as I go. Thanks!!

Extend Verizon 802.11g router using AEBS in bridge mode for better reception by Airport Express at other end of apt.?

I connect to the internet using a Verizon FIOS router, 802.11g. The brand name is Actiontec MI424-Rev. D. I stream music from my MacBook Pro and/or iPhone and use an Airport Express to connect to my stereo receiver, which is wired to in-wall speakers. The streaming experience is pretty uneven. The Apple Store recommended an Airport Extreme to beef up the network. Note: this is an average Manhattan apartment, not a vast mansion, but there is lots of interference due to a couple dozen other wireless networks in my building. Which is the best way to set up the network for more robust streaming and fewer dropouts?

Ok, then let's start with the following as the basic configuration of your "single" wireless network.
The Actiontec will be the main Internet router; no configuration changes would be required.
Connect the 802.11n AirPort Extreme Base Station (AEBSn) directly to the Actiontec router by Ethernet; reconfigure the AEBSn as a bridge, and also, reconfigure the AEBSn as the "main" base station in the extended wireless network.
Connect the 802.11n AirPort Express Base Station (AXn), by wireless to the AEBSn. Configure the AXn to extend the wireless range of the AEBSn.
The following are step-by-step instructions on configuring the AirPorts for an extended network:
Dynamic WDS - Extending a Wireless Network Setup
Temporarily connect the AXn directly to one of the available LAN ports on the AEBSn during the setup phase. Once completed, disconnect the AXn and place it at the desired location.
Open AirPort Utility, and then, select the AEBSn.
Choose Manual Setup from the Base Station menu. Enter the base station password if necessary.
Click Internet in the toolbar, and then, click on the Internet Connection tab. Change Connection Sharing to "Off (Bridge Mode)."
Click AirPort in the toolbar, and then, click on the Wireless tab.
Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then, select the “Allow this network to be extended” checkbox.
Next, select the AXn, and then, choose Manual Setup from the Base Station menu. Enter the base station password if necessary.
Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then, choose the network you want to extend from the Network Name pop-up menu.
Enter the base station network and base station password if necessary.
Click Update to update the base station with new network settings.
(ref: Pages 43-44 of Apple AirPort Networks.)
(ref: Wi-Fi base stations: Extending the range of your wireless network by adding additional Wi-Fi base stations)

Airport Express (Model with 802.11G +54MBPS Mac/PC and Set Up Issues

Hi,
We have a 4 Mac and 1 PC Household. Cable Internet Service by Roadrunner.Cable model (owned) connected to a D-Link 802.11G wi fi router (by ethernet from cable modem)in the family room , then out to a Imac (the half moon base and LCD screen with a airport card also in the family room and the closet computer to the D-Link
router, (we did add a D-Link antenna to the router ? about 10 months ago (a D-Link ANT24-0700 (Version 1.2)and a HP 4 in 1 printer attached via USB to the Imac
,a eMac 1.25 ghz 1Gb ram with airpot card also connected wirelessly (no printer attached on the same floor but in a ajoinging room about 20 feet from the Router, and another eMac 1.0 Ghz 1Gb ram with airport card in the upstairs part of our house (a bedroom) and no issue with Internet connection (it has a Epson 3in 1 printer attached via USB, and a MacBook Pro with 802.11N wireless card in side , bought for a Christmas/Birthday Present and also for college.It to has no issues with the Internet where ever it may be in the house. Our sole PC a HP tower with a added D-Link WDA -2320 Range Booster Desktop Adapter (802.11G) and we added a D-Link Antenna same model as the other a ANT24-0700 to help with Internet access which it did as well as adding some ram to increase page loading time etc. It does not have a printer attached. I will get to the Topic Area now
The Airport Express. I was not involved in the set-up as I was laid up due to a bad back and post major knee surgery , But I always (especially recently) wondered why the light was amber and blinking. I read through the manual and also
Apple.com support and MacFixit.com (which is under construction and moved to part of Cnet.com)and then went to the Airport Express Discussion area (sorry for being so wordy) I need a Twitter account to post!) We have a network name for the D-Link and the computers all were added and it also supports a Xbox 360, a Sony PlayStation 3 and a Nintendo Wi (in online use without issue) but..
A network was also as it appears to myself) for the Airport Express and under the half moon bars showing connection strenght (there is our D-Link network "phoenix" with security protection WPA2 I believe) as I have set up the router, We had a Apple Base station prior that was ? 802.11B (a half moon white unit) still have it in the box ) So for normal daily use, checking e-mail and internet use all of the computers use the "phoenix" or D-Link supported Router 802.11G
and The other network calld Apple Network with numbers and letters after it (and hopefully security) password is unknown , The Airport Express is set up connected via USB to a HP B&W laser printer which has saved quite a bit of money on ink, To utilize that printer you must switch from "phoenix" The D-Link router network to the Apple Network (followed by letters and numbers) The Imac and the eMac in the family room and a ajoing room (after switching to the Apple Network
can than print to the lasr printer. The eMac upstairs and the HP Windows XP Professional software can not print to the laser printer (yet the HP PC shows it as a individual network and a strong signal, equal to the Internet connection from the D-Link, and the eMac (after switching under the half moon (not the proper name I am sure) to get to the Apple Network to print , it will not print, yet it shows a 5 bar signal, same as the D-Link connection. I do believe we have two seperate networks (but do not understand why the two Mac's in the family room can print to the laser printer by simply switching networks and then file and print. ** One other 9probaly major item is that it states to set up the Airport Express with a Mac With OSX 10.4 or later (at the time of set up, we had the Imac and two eMac's all running Panther OSX 10.3.9 9which they continue to have installed) We obtained the HP Tower and Monitor and HP 4in 1 printer ust before Christmas in 2008 and the MacBook Pro in Mid December 2009 (current model and running Snow Leopard 10.6. The HP Tower runs Windows Xp Professional (Service Pack 3) so the MacBook Pro which is much more mobile , could be used to do the set-up, or the HP Tower coulf be moved temprarily, I do recall if Router changes (at least with The D-Link You need to be connected by Ethernet to the Mac
that would be doing the set up/configuration of the router (and it runs OSX 10.3.9 and is a older Mac (with 80Gb Hard drive that is partioned for OS9 and OSX as well , it is under a Ghz processor wise and less than 1 Gb of ram as the last ram slot required a seal to be broken and 256mb of ram (?) could be added
it has 768 mb of ram but knock on wood running well. We use Lacie external drives
on the Imac and both eMac's and need to get external drives for the HP PC as well as the Mac Book Pro (15" screen)
I apoogize if I repeated myself, and rambled but I wanted to (in one post) to explain our set up and network configuration
Questions
1) if indeed it is that the two networks is true and a set yp that is not correct
can the Airport Express be configured without opening up the router (when ever that happens it seems one computer is unable to get online and each time its a differnt one a Mac or veen the PC
The PC under My Computer and Networks clearly shows the wto distinct and seperate netwoks with strong signals and the distance is not far (it is through a floor as the other emac and the PC are upstairs and cabling by ethernet is not a option
2) If I need to open the router would I add the Airport Express as a client as if it was one of the computers or gaming systems on the network? (adding the Mac adress or IP address (not sure how you find the Mac address) and its been while since the router was opened up for any additions or work on it.
3) would it be on the same channel as the router or not ?
4) Hopefully with proper configuration the light will stay on (and green) on the A/E and the eMac and HP PC will be able to print to the laser printer. Currentlt
when anything needs printed from the PC its put on a Flasg Drive and plugged in tothe Imac and the the Apple Network is selected and data printed, The eMac upstairs has the option of using the attached Epson 3 in one or doing the Flash stick work around.
I would be verya appreciative if some one took a look at the set up above and advised me of what is right, what is not right* and what to do to fix things up
I would imagine after proper set up, delete the Apple Network from the PC and eMac upstairs and ? all of the computers as we should have one base station (the D-link and the spoke (the A/E connected by UBS to the A/E (it may be ethernet but the cable connection from the A/E to the HP laser printer is correct (the rest of the A/E set up ... Please , tell me where it is and where it should be
and ? any idea why we can print to the laser printer down stairs and not up stairs ? it did mention printer set up with Panther as possible, page 43 of themanual we have un chaper 5 Tips and Troubleshooting (under whn your printer isn't responding) (we do not have the interfereance listed in the manual,
our phones are land line, one 900 mghz and the others 5.8 ghz
It is possible to move the A/E and laser printer if that would help the two computers (desktops) upstairs) bt the distance is way less than 150 but their is a floor and ? duct work (metal ) but I think here is a place to stop typing and let some of the experts on the discussion forums take a look.
one lst note (as the lap top will be going off to college in the fall (runnning Snow Leopard, and the other 3 Mac's run Panther OSX 10.3.9 should the HP PC windows Xp Professional be the computer to set up the air port express and the Airport Utility proram installed & would this conflict with the current Router (set up by a Macc running OSX 10.3.9 (Panther) i.e (should both set ups be on the same computer?) but actually aThe D-Link is OSX10.3.9 compatible (and 802.11G) and set up requires ethernet connection to a Mac (You type in the numbers and . etc and password as administror and you are in, or should the admin be on the same cpmpuer for the router and A/E ?
(and considering a Airport Extreme Base Station as well as dual frequency simulataneus and 802.11N (for the laptop now) and future, or wait. The 802.11
in theory would broadcast farther..?? even if computers had 802.11b(our Mac Desk tops and the PC 802.11B card
Thanks Again!!!
Many, Many Thanks
amnienttales

William Boyd Jr.
Hello again,
D-Link Router is model DGL-4300 (along with a D-Link ANT24-0700 Omnidirectional
7dbi Antenna . Our Cable Internet ISP (Roadrunner) provides consumers with dynamic ISP address's . All Mac's have Airport Cards and The Hp Tower XW4550 has a D-Link Rangebooster G Desktop Adapter WDA-2320 (also with a D-Link ANT24-0700 Omnidirectional 7 dbi Antenna (the PC OS is Win XP Pro Service Pack 3) The 3 desktop Mac's run OSX Panther 10.3.9 , The 15" MacBook Pro OS is OSX 10.6 Snow
Leopard (not sure what is after the .6 (right now) D-Link's website is
http://www.dlink.com , I have configured this router multiple times in the past.
also added as clients on the network (Utilizing the D-Link Router) are a X-Box 360, Sony Play Station PS3, and a Nintendo Wii all of which have on line ability
and enables online video game play with any one online.
As mentioned prior the Airport Port Express is Model A1084 Part No. M9447OLL/A
which is USB conected to a HP LaseJet B&W , model 1020 and some how the two computers near it can switch to the Airport Express Network from the D-Link Router based Network and print wirelessly to the A/E connected LaserJetPrinter
I realize I will need to reconfigure the D-Link Router and add the A/E as a client. I will try first to use the Airport Utility and see if I can do anything
Utilizing it (adding it to the D-Link network, I think its unlikely but worth a try but* the password is unknown but I have a few guess's as to what it may be.
I do have the necessary admin and network paswwords to cconfigure the D-Link Router,
1) * If the the A/E Utility experiment fails and I need to re-configure the router * do I need to (as per the Airport Express Set Up Guide (Use a Mac with OSX 10.4 or later or a PC with Win Xp Home or Professional (have a desk top PC that has the specs) and The Mac Book Pro meets the Mac Spec's)
If I can not get a password to work on the A/E I would reset it using the reset button
And before plugging in the A/E , connect the appropraite cables in our case a USB cable to the LaserJet Printer then plug in the A/E
2) I would then connect by Ethernet from Either the Mac Laptop or The PC to the D-Link router (if not the router will not set-up correctly)
3) The one question that puzzles me is that we are not using the A/E as a base
but a client
in two sections(Using Airport Express , connecting a Printer via USB
and use Airprt Utility to create a new network or join a new newWireless computers using Mac OSX 10.2.7 (Tiger) or later or a PC with Windows XP and it then goes in to the steps of ising the printer for both a Mac and a PC (using Bonjour on the CD that came with the A/E (this appears to contradict needing to use Mac OSx 10.4 or a PC with Win Xp set the A/E up for use as a printer
(joiing a new network or existig one)
And in Chapter 5 Tips and Roubleshooting= Your Airport Express Status Light Flashes amber & Your Printer is not responding (it is flashing amber and the printer does not respond to the two computers upsstairs (one Mac running OSX 10.3.9 & One PC running WinXp and its states to make sure the printer is selected
in the Printer list o client computers, to do this on a Mac using OSX 10.3 or later , open Printer Set Up Utility and follow steps and if a PC with Windows XP , Open Printers and faxes and then follow steps
in Closing ? can I configure the A/E Utility with a Mac using 10.3.9 as above or
? Per Chapter 1 Getting Started use a Mac with OSX 10.4 or later or a PC with Windows Xp Home or Professional
Perhaps I am taking the tips and trouble shooting and Printer Set up out of context or does the getting Started Computer specs contradict them or are they
for use if the A/E was going to be a Base Station and not a client..
Will keep at it,
ambienttales

Buy 802.11N AirPort Extreme & Use old 802.11g as router to connect xbox

My son's xbox 360 was connected via an airport express to my wireless LAN which uses the older "dome" 802.11g airport base station. This worked well until the airport express express "burned out". I was going to buy a new airport express 802.11N for $99 but then realized that by buying an airport extreme 802.11N base station (for $179) and using my old 802.11g base station instead of a new airport express 802.11N to connect to the xbox, I would be upgrading my household LAN to 802.11N for only $79 more than the cost of a new airport express.
I am concerned that by using the 802.11g as a router to connect to the xbox I woud be slowing down the whole network thus defeating the purpose of upgrading my current LAN with a new 802.11N extreme base station.
Is there a "right" way to configure the network so as to use my old
802.11g airport extreme as a wireless router (instead of a new airport express) to connect to the xbox without slowing the whole network?
What do people do with their old 802.11g airport extremes when they upgrade to the 802.11N airport extreme base station?

+My question is this: may I toggle the 2004 g extreme on and off -as needed- to extend or use a printer?+
If all of the devices on the network are "n", then you'll be able to make use of Apples new "extend a wireless network" configuration. The wireless will operate at much faster "n" speeds.
If you add a new AirPort Extreme "n" and you want the older "g" Extreme to "extend", you'll still have to use the older WDS setup on all of the routers on the network. This will drop the entire network down to "g" levels and cause a signficant loss of bandwidth as well. In effect, it would be the same as if you had all older "g" routers on your network.
You could configure the older Extreme to "join" the wireless network. It would not provide any additional wireless coverage configured this way, but it would allow the other "n" devices to operate at "n" levels. You could plug a printer into this device assuming that it's compatible with remote printing at the USB port of the Extreme.
I would not recommend turning a network device on and off as this will surely cause connection issues with other network devices, probably sooner rather than later. If you plan to use the older "g" Extreme to provide a print function, plan on leaving it powered on with the rest of the network.

Airport Extreme 802.11g vs.Belkin wireless g plus mimo router

I have an Airport Extreme 802.11g and have been having some trouble with hanging connections via my Comcast cable modem. Today I was in Staples and on a whim, bought a Belkin wireless G plus mimo router thinking that switching routers might solve my problems. Before I even take this thing out of the box, can anyone compare the 2? Am I better off just sticking with the Airport?

I have an Airport Extreme 802.11g and have been having some trouble with hanging connections via my Comcast cable modem. Today I was in Staples and on a whim, bought a Belkin wireless G plus mimo router thinking that switching routers might solve my problems. Before I even take this thing out of the box, can anyone compare the 2? Am I better off just sticking with the Airport?

Post Moved Broadcom WLAN 802.11g "No signal" sinc...

Post moved to Other BB Queries http://community.bt.com/t5/Other-BB-Queries/Broadcom-WLAN-802-11g-quot-No-signal-quot-since-installi...
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

it could just be the wireless software isn't detecting a signal. what i used to do when i used windows was ( from memory, i no longer use windows since 2004 )
1 ) insert the hardware
2 ) boot windows
3 ) it will detect new hardware
4 ) when it asks for drivers,insert cd
5 ) point windows to the devices driver folder on the cd
6 ) windows installs driver,then asks to reboot
7 ) after reboot,use windows to manage your wireless connections.
used to work all the time, give it a try,YMMV, any problems report back with any errors/problems and i will try and help
free your computer, use opensource
i'm a linux user & very happy about it

802.11g on a Firewire G3

My router handles 11g. What do I need to use 11g on my Powerbook?

The only option if you have an old PB to upgrade to 802.11g is to purchase an PCMCIA 802.11g card. Or you could use a 802.11g wireless bridge (but this is not very portable, but can be a solution for an old iMac).
You want a third party WLAN Cardbus cards based on the same Broadcomm chipset that Apple used in the Airport Extreme which will work in a Mac running OS X 10.2.6 or later and Airport 3.1 or later.
Companies using the Broadcomm chipset include: Linksys, Buffalo Technology, Belkin.
Not all cards though do work.
Another option is to use an Atheros card with the Orangeware driver.
The other thing to consider is that do you really really need the extra speed of 802.11g. The only real benefit is if you are transferring really really large files in an internal network (eg video files) and has no "real" impact on wireless internet access (as 11Mbps is generally a lot faster than your average 512Kbps ADSL speed).

Macbook air WLAN - Belkin Router

Hallo ich habe ein grosses Problem mein Macbook Air (juli 2013) in mein wlan zu integrieren. Bei dem Router handelt es sich um einen Belkin der einen recht guten Grund bildet. Bisher hatte auch noch kein anderes Gerät ein problem mit dem router. Ich habe dort ein PC dran, diverse Handies von mir und Freunden fanden dort auch schon anschluss. Doch mein macbook air weigert sich stetig das Teil zu aktzeptieren.
Zu den Einstellungen: Der Router war so eingestellt das er ich automatisch fuer 802.11g oder n entscheidet je nach Gerät. Und so dass er sich selbst den Kanal aussucht. Ebenso WPA oder WPA2. Im DHCP bekam es oftmals keine IP und nahm sich eine pseudo Ip adresse was vorne und hinten nicht klappte. Irgendwann klappte es aber zwischen durch doch mal das es sich die richtige adresse via DHCP nahm, allerdings hatte es NIE internet.
Ich habe somit die settings des routers festgelegt und das netz auf 802.11g gesetzt , channel 6 und wpa2 da ich aus erfahrung schon einmal ein problem mit einem anderen wlan router und android hatte und der router fuer das handy nur klappte wenn die settings festgelegt sind. Allerdings brachte mir das hier auch nix. DNS ist ebenfalls nicht da, also er kommt komplett nicht in das internet. Das lokale netzwerk funktioniert.
Ich verstehe noch nicht ganz warum das so sein kann.
Ich versuchte auch das book mit einem thunderbold adapter and lokale lan zu klemmen aber GENAU das gleiche problem.
Jedes andere Geraet klappt bisher. Weiss jemand einen Tipp?
Liebe Gruesse,
mgirmes
Hi There,
i got a huge problem with my new macbook air (rev. july 2013). At home i got a belkin wlan router.
The Router should be something like this: http://www.belkin.com/de/F7D1301-Belkin/p/P-F7D1301
It got different channels, WIFI 802.11g , n & automatic
The strangest thing : devices by friends as well as my own android works totally fine. Zero issues.
Now to the MacBook Internet connect process:
The first configuration i got was 802.11g&n, channel by automatic and WPA/WPA2...
The login and IP by DHCP works but i cannot get access to the Internet.
I tried to restrict the parameters.
So i choose channel 6 , 802.11g and WPA2
Same problem IP by DHCP works but no access.
Sometimes the macbook isnt even able to get an ip from dhcp ... dunno why but the macbook picks a TOTALLY random IP in this case.
I guess may be the DNS isnt right, so i first pinged a site to see if anything gets out but nothing. Even pinging the IP of for example heise.de doesnt work.
I can ping my Local win pc but i cant ping my router. .... this is may be blocked. But i have to go over the router to come to my pc so .... this connect must be there.
Even after all of this i got a Thunderbold -> LAN adapter.
So i tried my luck by Ethernet.
But the same issues appear. I ll try to get a new firmware update for the belkin as soon as i be at the device.
ANY advices for this atm?
regards,
mgirmes

My MBA works fine with my Linksys EA3500 router.
It also worked fine with my previous Linksys E3000 and WRT320N routers.
How old is your router?
Is the firmware up to date?
If it doesn't support 802.11n it is time for a new router.

Time to upgrade to 802.11g???

Any views would be appreciated - I'm running a 802.11b wireless router with an iMac and PB connected. Basically, is it worth investing in 802.11g (AirPort Extreme Base Station)?
Thanks

There are so many factors to consider when creating a wireless network. 802.11b advertised throughput is 11mbps and 802.11g is 54mbps. But the actual throughput for these is typically 4-7mbps and 22-27mbps respectively.
With security encryption like WPA, there is additional overhead that lowers throughput.
Other important things to consider/remember is that the radio in the AEBS handles one data packet per user at a time. So, if you and a friend were both downloading a file, the radio is not simultaneously sending the two of you data; it sends packets to each of you one at a time. The more users using your wireless connection, the slower it will seem.
Finally, it all comes down to Internet link you have. How much bandwidth does your ISP provide? Your ISP may support less bandwidth than the AEBS is capable of, therefore making the ISP your limitation.
Sorry - no clear answer. I have an AEBS (802.11g) and it's nice...if that helps.
Various Macs and PC's Mac OS X (10.4)
Various Macs and PC's Mac OS X (10.4)

Airport Extreme 802.11g base station loses internet connection often

I just installed an Airport Extreme base station (802.11g version Apple Base Station V5.7) last week. And it keeps dropping my internet connection at least once a day.
I simply replaced an old SMC Barricade wireless router that died (and was a POS). But I only had to reset the SMC about once every 2 months. Nothing else has changed in my setup. Only the router/base station is different.
The wireless part is fine. Even when the internet connection gets dropped the hard wired AND wireless clients can still access the local network. Reseting the DSL modem has no effect. The only solution is to power cycle (unplug and plug back in) the AEBS OR restart it from Airport Admin utility.
But you can't do that from offsite. When the AEBS drops the internet connection I can't access my office network from home!
Is there a place in Airport Admin Utility which tells you the status of your internet connection like most generic wireless routers with web-based software do?
Any ideas on resolving this?
Thanks

"Any ideas on resolving this?"
Looter,
Based on your description, open AirPort Admin Utility and check the configuration of your main base station on the "Internet" pane. If you're using ethernet cable from the modem to the base station, the top selector [Connect Using:] should show "Ethernet" and the second selector [Configure:] should show "Using DHCP"
Also, check your iMac's System Preferences>Network at "Show: AirPort" and check the PPPoE pane which should show no entries (unless your isp requires its use), and the TCP/IP pane which should show "Configure IPv4:" as being "Using DHCP" - while all other info is filled in automatically.
"Is there a place in Airport Admin Utility which tells you the status of your internet connection like most generic wireless routers with web-based software do?"
No, the AirPort Admin Utility is not web-based, only located on your computer with the information available to it necessary to operate the AirPort system. It does not actually administer the signal. I think that is done only by System Preferences>Network.
"I'm actually referring to the Airport Express base station not my MacBook Pro's wireless connection. Is there anywhere in the Airport Admin Utility software that tells you the status of the AEBS' internet connection NOT the wireless connection."
No, that info is not available in that utility. The information you seek is at System Preferences>Network, but only after the system scans for it. Click the "Assist me..." button and then, on the "Do you need assistance setting up a new network connection or solving a network problem?" panel that opens, click the "Diagnostics..." button. A "Network Diagnostics" panel will then open and if its scan shows there is no internet the lights to the left of "Internet" and "Server" will be yellow instead of green. Meanwhile, it continues scanning for the connection until it is re-established. I determined this by pulling my cable from the phone jack, later reinserting it.
Further information that may be helpful to you can undoubtedly be found in threads such as this other one:
http://discussions.apple.com/thread.jspa?threadID=884049&tstart=0
edit-
In re-reading, I may not have given you what you need. It sounds as if you may be "timing out" somehow on your connection. You might want to check around at some of your log-on settings to see if there is that possibility connected to one of them, even though the only thing I can think of is the "Renew DHCP Lease" button which is unknown to me, as I've never used it.
Message was edited by: myhighway

Creating a 802.11g network with Base Station in "802.11n only" mode

I still have some legacy products running 802.11b/g, and want my Base Station to run in "n" only mode at 5GHz to keep the rest of the network as fast as possible.
My current strategy is to take an old 802.11g router, put it into access point mode, and connect it to the Base Station with an ethernet cable.
Unfortunately, this access point seems to fail frequently - connected devices can't find the access point, and rebooting the access point will temporarily fix the problem.
I'm wondering if an AirPort Express can replace the access point. It can run as "create a wireless network" in a mixed b/g/n mode. I would then cable it to the base station.
Will this slow down the remainder of the "pure" "n" network?
Steve

I was asking something similar in another thread. What I'd like to do is run my existing b/g AP as it is and enable an Airport Extreme Base Station in AP mode in n-only mode. Supposedly, you can do this.

Xbox 360, My Airport Express 802.11g, and my ever more looming suicide...

I hate working on networks, especially when it comes to making Xboxs work on em. But Im a slave to live and I MUST have it. Now I have connected flawlessly to linksys routers, but this Airport is making want to take my cranium and bash it into the sidewalk until the blood drains from my skull, resulting in my inevitable and permanent resting state. So it goes...
Ok, I'm not going to kill myself, but christ will someone help me out here?
Heres what I got on the Network screen
IP- 10.0.1.2
Subnet- 255.255.255.0
Router/Gateway/Whatever- 10.0.1.1
DHCP- is set to automatic
I have 2 Macbooks connected to this router, they work fine, as well as 2 iPod touches
On the Xbox360
-IP set to automatic, given 169.254.100.112, I assume this was assigned by the router, but this makes no sense because when I run diagnostics I get IP Address Failed. THIS IS THE MAJOR ISSUE IM ADDRESSING RIGHT NOW... But I assume DNS is gonna fail even if I get IP going. I could use all the help I can get y'all.
Subnet- 255.255.255.0
Gateway- 10.0.1.1
DNS- 10.0.1.1
Wireless mode 802.11g
Network- vargas
Network type- Infrastructure Channel 1
Security WEP.
I hate life.
This is not working. I have called my genius bloody uncle, and even he seemed stunned at the matter. This is ridiculous... I hate it so much. Hours I've wasted for nothing. Someone, anyone, if youre reading this and you think you can help, please, please...

Added note, I'm running tiger OS X 10.4.11. I think I have an airport express, its my step dads. I think. I wanna say I wanna manually assign IP to something like 10.0.1.10 but I already tried that. To no avail. I've tried restarting the router and xbox and nothing really works.

Connecting to 802.11g Projector

Just received a Hitachi CP-X2 LCD projector. All works fine when connected via video cable. I insert its wireless 802.11g card, and WiFind "sees" the unsecured device - but I cannot properly access the projector.
Where's a tutotial on establishing this type of connection with a MacBook Pro?

OK - I see
The projector needs to connect to a network (to be set up under the MIU menu / SETUP on the projector). Either turn DHCP on (if your base station is providing DHCP) or provide IP address, subnet mask and default gateway (the routers IP number). You also have to set the wireless channel (CH, normally 11) and the encryption (WEP / WPA) if any, leave the SPEED parameter at AUTO and set the NETWORK MODE to wireless; the MODE is normally infrastructure when using a base station.
The projector needs to have a valid IP configuration (and encryption settings if applicable) otherwise it cannot connect to the network. Normally the network will include a wireless router - but you can also set up the MBP to share the internet connection (when you do this the Airport antenna can not be used to connect to a router at the same time) under System Preferences - Sharing - Internet. The projector can then use the MBP as the gateway. I always use an Airport Express as it is more convenient and have not much experience with the latter set-up. Maybe somebody else can give more details here.
HTH,
Uwe

Why won't my iPad 2 connect to my 802.11g network?

Hello everyone,
Today I received an iPad 2 as a gift. It is the first Apple product I have ever owned. I spent about 3 hours this morning trying to get it to turn on -- it kept displaying an image of a USB cord so I connected it to my computer. Still the iPad would not display its desktop. Finally, I learned that the iPad had to be connected to a PC running Windows (instead of the Centos 5 Linux system that I use). Additionally iTunes had to be installed. I find it extremely bizaare to require the device to connect to a computer before being able to turn it on.
Now after getting the device to boot, I am attempting to connect to my home wireless network. Thus far it appears this is going to be Strike Two for me and the iPad 2. My wifi network is 802.11g using WPA2-AES and 128 bit key. The iPad 2 recognizes the presence of my network (the SSID appears in the listing when it prompts me to connect), however, when I supply the 128bit key to connect, the iPad 2 reports that it is unable to connect.
I went into the Network configuration in the General Settings and attempted to add the network manually (ensuring I could specify WPA2 as the encryption type). Same failure.
Any hints on getting this thing to connect to my network? I've already watered the security down to 128bit encryption (from 256bit). All the other devices in my home are able to connect without issue. The iPad 2 detects a strong signal from the router.
Thanks,
Josh

I appreciate everyone that responded with the intent of helping me solve the issue. This forum is weird -- there are many users that try to help with iPad2 issues and then there are many that mock me and say I should just return it for expecting this very expensive device to just work.
After a late night of debugging with Wireshark, I finally tracked down the problem (Apple, feel free to send me a cheque for my services)
I will post the solution here for those who desire to use an 802.11x security protocol that has not yet been compromised (WPA2-AES).
When you attempt to join a wireless network, the iPad asks for the password. If this password contains any characters other than 0-9, A-F (hexadecimal), WPA states that Password Based Key Derivation Function 2 (RSA Security, PKCS #5) must be used to calculate the pre-shared key. If however, the password contains only hexadecimal characters, then that value *is* the key to be used (e.g. do not run the PBKDF2 function)
I specify my network keys in hex both in my router and my devices. This means the devices nor the router need to invoke PBKDF2.
The key I specified in my router was entered using upper case hexadecimal letters (e.g. A, B, C, D, E, F) whereas the key I entered on the iPad 2 was entered using lower case hexadecimal letters (e.g. a, b, c, d, e, f). Since I am specifying a key, the uppercase and lower case hexadecimal values have the same binary represention -- meaning they are identical. The iPad, however, does not treat them as identical and therefore attemps to connect using an invalid pre-shared key (my guess is it is running PBKDF2 when it shouldn't be -- but I don't care enough to troubleshoot it any further)
In summary, this issue will only affect those of us that specify our pre-shared keys explicitly (via hexadecimal) in the router. As a workaround, make sure you enter the hexadecimal key using only lower case letters (a-f) when you set the key in the router and use lower case letters (default) when entering the key on the iPad 2.
After doing so, iPad 2 can connect as can the other 20 devices I own that followed the WPA specification in the first place.
Josh

MSI RG300N WLAN-N ROUTER 802.11G+N

Similar Messages

Maybe you are looking for