MSI X58 Eclipse 7520 - Latest BIOS & CPU support List?

Hi...
http://www.msi.com/product/mb/Eclipse-SLI.html#?div=CPUSupport
http://www.msi.com/product/mb/Eclipse-SLI.html#/?div=Download
does Bios v1F support newer Xeon w3690, 990x, 995x ?
CPU support page is outdated..
.txt does not say.

Quote
does Bios v1F support newer Xeon w3690, 990x, 995x ?
Recommend to open a ticket with MSI Tech Support & ask them.

Similar Messages

  • MSI X58 PLATINUM, the latest bios and how to enable turbo boost

    1) Wich motherboard is ? MSI X58 PLATINUM or MSI X58 PLATINUM SLI ?
    2) What is the lastest version Bios and where can i get ?
    3) How to enable turbo boost in this motherboard ?
    4) Thanks so much guys. 

    My bad. The obvious lack of your self research got the better of me. I do not take helping, if I can, lightly. This is new technology, & a lot of expertise is in short supply. I downloaded the manual on this board & read the bios section, & in CMOS Setup, you should find an "Enable" setting for Turbo Boost. If you don't, please contact MSI Tech Staff @ http://ocss.msi.com.tw Also, (in your manual), is a reference under "Intel Turbo Boost Tech", which clearly states "for further information please refer to Intel's official website". By your original post, CPU-Z says it's an SLI? What did you buy? Does it say on the retail box? At MSI's website, the X58 Platinum (not the SLI), has version 1.0 bios offered in three global region zip files. M7522v1.0 Euro.zip, M7522v1.0 ASIA.zip, & E7522v1.0.zip. J.T.N. is correct, the SLI board takes something else. Are both boards bios's compatable? I have no idea. Recommend step one as to confirm with MSI what board you truly have & go from there. 

  • MOVED: MSI X58 eclipse SLI CPU throttling problem

    This topic has been moved to Overclockers & Modding Corner.
    https://forum-en.msi.com/index.php?topic=128074.0

    Quote from: goofazoid on 03-October-09, 15:03:29
    If you turn EIST off you should be able to put the multiplier to a specific number between 12 and 21 (or higher if you have an unlocked Extreme CPU) and that is where it will stay.
    I believe that is exactly what i did, i disabled EIST, C1E and set multiplier to 21, however, when i run a stability test(Prime95 or Linx) it always drops the multiplier down from 21x to 20x.
    It seems to me turbo mode is still working when it is supposed to be disabled when you set multiplier to 21(or maybe it is just simply won't allow x21 multiplier to be used at full load anyway, turbo mode on or off).
    Quote
    Very good point Jack. There you go ravescar & others, give that a try & see if it makes a difference. smile
    I experimented a bit with Overspeed Protection enabled and disabled, however i did not notice any difference in this regard, the multiplier still drops to 20 on high load for me.
    However this problem do not happen if i set multiplier to 20, it is only the 21 multiplier that have this issue.
    This is on a MSI X58 Eclipse SLI Motherboard + i7 920 D0 stepping + 6gb GSKILL Trident 16000 CL9 RAM.
    Quote
    BTW. I've read of a couple of cases where DO stepping 920's getting 22x with Turbo enabled but I'll remain skeptical regarding the validity.
    Maybe it is just earlier version of cpu-z mis-reporting multiplier?

  • First Look.MSI X58 Eclipse

    No heatpipes/heatsinks shown as yet.
    http://www.bit-tech.net/hardware/2008/08/26/early-look-msi-x58-eclipse/1

    well, I never image that a gaming NB could be so slim like a Ultrabook, I guess this GS70 is made by metal and with very advance thermal design, the VGA and CPU is the highest power consumption parts and GS70 just handel the balence of thermal and high performance..... you can tell by the picture that is super slim....

  • MSI Prescott CPU Support List (FSB800, 1M L2)

    finally...
    http://www.xbitlabs.com/news/mainboards/display/20031215133027.html
    and
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=proscott

    At last, a clear answer from MSI, after 6 months of waiting  
    MSI Prescott CPU Support List (FSB800, 1M L2)
    Chipset_Model Board_Name  BIOS_Version  Prescott_Support
    Intel® 875P 875P Neo-LSR/-FIS2R AMI 1.8 YES
    Intel® 865PE 865PE Neo2-PS/-PLS/-PFISR AMI 3.2 YES
    Intel® 865PE 865PE Neo2-S/-LS/-FIS2R AMI 1.9 YES
    MSI P4 Extreme Edition Support List (FSB800, 2M L3)  
    Chipset_Model Board_Name  BIOS_Version  Prescott_Support
    Intel® 875P 875P Neo-LSR/-FIS2R AMI 1.8 YES
    Intel® 865PE 865PE Neo2-PS/-PLS/-PFISR AMI 3.2 YES
    Intel® 865PE 865PE Neo2-S/-LS/-FIS2R AMI 1.9  YES
    I guess Intel has the final samples with the manufacturers ...
    Now to save up for the CPU upgrade, the probable PSU upgrade, probably a better HSF or CPU cooling system, memory, etc...  
    But how can I test my system upgrade readiness before the 1 yr warranty expires?  

  • P45 Neo3-FR (PCB 1.0) CPU Support list ?

    Hi everyone!
    For some unknown reason, I can't seem to find anywhere the CPU Support list for this motherboard - P45 Neo3-FR (PCB 1.0).
    Could anyone here please shed a little light on this issue and tell me if it supports Intel Pentium E5400 (2M Cache, 2.70 GHz, 800 MHz FSB) ?
    Thanks,
    Saliman

    http://eu.msi.com/index.php?func=prodcpu2&prod_no=1611&maincat_no=1&orderby=cpu_name%20ASC#menu
    Quote
    tell me if it supports Intel Pentium E5400 (2M Cache, 2.70 GHz, 800 MHz FSB) ?
    Yes.

  • Msi Kt7 Pro2-a Kt133 highest cpu support???

    Yes I was wondering I have The
    MSI KT7 Pro2-A mobo
    Well my 4 year old duron 750 finally gave out cause it was chipped too much.:(
    I was wondering how high of a cpu with my motherboard take??
    Another thing about this board. Why is it that I can never update my Bios  past anything after 3.2. I've tried 3.5 with LiveUpdate it updates it but when it time to boot to windows it gave me "No Operating System Found"
    Then I just reflash it with 3.2 version so it would work again. I also follow that article on how to flash bios with a Ntfs parition. Still anything after 3.2 will not work with this board.
    So does anyone out their have this exact board but was able to flash beyond 3.2 bios version?
    Also I notice on the bios page that support for XP chips are only available for the turbo boards which I assume the Msi Kt7 pro2-a isn't.
    Yeah I know my board is old an probably won't support newer chips. But I really don't have the cash to get a new mobo but only for a cheap chip.
    So If anyone here has this exact board please tell me what chip you are running?
    Cause right now it seems like 1.2 duron is what I have to settle for since it's pretty cheap in price but not sure if my mobo will support it.

    I poked around the MSI archives, and here is a link to your CPU support - up to 1.2 Duron and 1.4 Tbird (both 100FSB). Good luck.  :]
    http://www.msi.com.tw/program/support/cpu_support/cpu/spt_cpu_detail.php?UID=99&NAME=MS-6330%20Ver1.0C

  • MSI K8N Neo-V nForce3 250 CPU Support

    I've been to about a million MSI pages looking for CPU support for this Mobo and can't find a definitive answer. I see where this board supports Semprons but does it support - AMD Sempron 64 3300+ Palermo 800MHz FSB Socket 754
    Or does 64 support only lend itself to Athlons.
    I think it does but before I buy I need to know fer sure.
    Thanks,
    Ahumado

    MakubeX,
    I have the Antec True Power 480. Unfortunately it only has 22 or 23 amps (the specs and the label on the psu have different ratings  ) on the +12V rail. Most of the folks here recommend a power supply with at least 24 amps.
    The good news is that the system in my sig is working flawlessly so the extra 1 or 2 amps don't seem to make a big difference, at least in my case. I will say, however, that according to Core Center my +12V rail runs around 11.5 volts, which is low and nearly out of ATX sepc. The low voltage will result in higher amperage draw...but again, the system is stable.
    I wish you good luck

  • FM2-A75IA-E53 CPU supported list is missing

    I read the subject about how to know the CPU supported by the Motherboards but in the case of FM2-A75IA-E53 motherboard there is no SUPPORT -> CPU SUPPORT in the product page.

    I think (hope) they are revamping them because they are definatly missing.
    Contact msi for this information for now.
    >>How to contact MSI.<<

  • CPU Support List for MoDT boards

    Hi!
    I can't find such info on the site and support staff seems to be too busy to answer me.
    Anybody knows full lists of CPUs compatible with the following boards: 945GT Speedster-A4R, 915GM Speedster-FA4?
    I'd like to buy a cheap used CPU but I need to know for sure what CPUs are supported.
    Thanks.
    Regards,
    Vitaly

    Quote from: vitvip
    Thank you, but actually this is the kind of information that can be found on the site as well. It gives some clue, however is not a CPU compatibility list. Core names are not official and are never mentioned on Intel site. Today, normally CPU compatibility list would include processor #s and required PCB and BIOS revisions.
    915GM Speedster-FA4 has been designed for Centrino.
    http://www.intel.com/products/chipsets/915GM/index.htm
    945GT Speedster-A4R has been designed for  Core Duo (478 pin)
    http://www.intel.com/products/chipsets/945GT/index.htm
    Both of them are old enough, so don't worry about BIOS revisions and other similar things.
    cheers

  • MS-7520 MSI x58 Eclipse HELP bios hangs!

    Heeeeelp...
    I just flashed my bios thru the live update.. restarted - made a decent OC to 3200, and my memory to 1600mHz.. Nothing dramatic..
    It booted up one time.. but stalled in win start..
    So I tryed to get into the bios again..
    But it just hangs at CPU ini..
    What can I do? really nervous about this...

    Quote from: Slunten on 09-February-09, 20:44:59
    Tryed to clear CMOS on the back of the motherboard-... But it doesnt react..
    Is there some kind of forceswitch at motherboard?
    EDIT: I used the resetswitch on the mobo
    Thnx VERY much for the input...
    the reason i wanted to flash my bios is because of some sound driver issue I got..
    So I thought it maybe would be a good Idea to update the bios..
    Don't think the hang issue has to do with flashing bios if u flash it correctly, most likely has to do with instability OC. I assume now all goes well after you reset the switch?

  • Msi x58 platinum 1.5 bios, have you tried ???

    i see that bios version 1.5 for the x58 platinum is officially out now on msi website downloads (not beta).
    has anyone tried it and is there any benefits noticible ?? iam still on version 1.1.

    Quote from: David J on 18-May-09, 03:15:41
    You asked Mike, but in layman's terms smart fan is a fan that will automatically adjust its rpms based on the system's temperature. S3 is an industry standard for when the computer goes to "sleep" in order to save energy.
    i went in bios for a look on smartfan, i found it, mines is disabled and iam unsure how it should be set, so i left it alone, it has options to change it from 40c up to 70c, but iam unsure what it should be set to, could someone tell me ??
    i also noticed that in bios i can set the system fans too, 3 settings, 50%, 75% and 100%, mines are all on 100%, again i left them alone at 100% as iam not sure what they should be set to, can someone please tell me ??
    This may help, i have an i7 920 and its clocked to 3500, my tempreatures are not too bad, on running the intel burn test the very very most the cpu temp peaks at for a second now and again is 64c.
    And my system sounds like a rocket ship, LOL, fans are LOUD.
    hope someone can help ,me.

  • Re: MSI X58 Pro-E (MS 7522) - Xeon support?

    Svet - oh, well, I hoped they are there... but nevermind. I drop MSI tech support an email: [email protected]
    Same as this thread. Hopefully I get some nice news, or there will be a ughly microcode update by force 
    Chike - Quoteor co...

    Quote from: Nichrome on Today at 21:07:17OK!
    How do you want Intel based motherboard to be compatible with AMD CPU 
    I&#39;m so sorry for being ignorant. Like I said, this is my first time building com...

  • MSI GT60 2OC unlocked latest bios

    Hi Svet please unlock/unhide all hidden options in bios version E16F4IMS.50Y non RAID SKU for my MSI GT60 2OC. Thx!
    Donation sent !
    Confirmation number: 5YG65632P8646554D.

    received it, will work on and send back to you when its done after 3-4 hours
    EDIT: It's now done, check PM

  • MSI N580GTX TwinFrozrII OC latest Bios??

    @svet
    hi, can u guys help me to see if the vbios i have is up to date or should i update.
    my gpu is currently a MSI N580GTX TwinFrozrII OC
    S/N: 602-V255-060B1104074753
    VBIOS:http://www.mediafire.com/download.php?zps7byb33bkrikn
    thanks...

    Hi zunaid, check this out : >>Disable GeForce GTX 580 Power Throttling using GPU-Z<<, but  I never do that because mycard already has OCP unlocker ^_^
    I also never run Furmark again as it draws too much power and can damage your card.
    Btw I think there is no new BIOS for GTX580.

Maybe you are looking for

  • Videos on my macbook pro won't play sound after apple tv was installed in the house

    Hi! Need some help... for christmas my dad received the little black Apple TV device to watch videos on our big tv from his iPad. After it was installed no sound came from my macbook, it instead comes out of the tv speakers. When dad is airplaying a

  • Zero price for item category

    Hi , I want to controll the price by item category, I want my user to manually change the item category to zzzz  in case the material is sent as sample. For item category B the pricing field has "B" (PRICING FOR FREE GOODS 100%) while making sales or

  • Hyperlink outside of website

    I'm pretty limited in my coldfusion knowledge. I am trying to create a link that will reference a website outside of my own and can't seem to make it work. I'm putting in <a href="Outside Website address>Title</a> but it keeps trying to go to my webs

  • Javascript doNavigate problem

    EP6, SP12 My doNavigate call in my htm page isn't working, it's giving a permission denied error.  My htm page is on a different server.  My iview is on the same .domain.com as the portal, and both are non SSL (http://).  I've event set my document.d

  • Help with glitches/lines

    When I am working in Premier C6 every so often I start getting glitches or flashing white lines in the playback. I close down and restart program and they are gone. Now when I exported a file It will show up in files.  Thank you.