MSI x99 AC Power Bios Update

When will the x99 ac power be getting a new bios update? is one planned?

Quote from: Nichrome on 06-October-14, 01:52:06
Is a new one planned? Most likely yes, but I have no clue about time when it will be released.
Contact MSI:
>>How to contact MSI.<<

Similar Messages

  • MSI X99S Xpower AC Bios Update Failure

    While flashing my bios tonight to the most recent version, my pc power accidently cycled power.  It was updating the "A" bios at the time.  I can still boot via B which I successfully flashed to the most recent just before doing A.  Is there a way to recover A or is it permanent?  B boots  fine, but A just freezes on a black screen.  Any suggestions on what to do will be appreciated.  My pc specs are in my footer.

    My BIOS B has the most recent for this board (1.6 dated 2015-01-17).  Yesterday, when I spoke to MSI tech support, they told me to stick the USB drive with the bios into one of the rear USB ports of the motherboard instead of the direct USB port adjacent to the BIOS selector switch on the board, restart my pc, and when I get to the bios screen to switch over the BIOS switch to A, then run M-FLASH and the A should be updated.  I did this, I can use my keyboard and mouse with this configuration, however, after I switch over to the A BIOS and start M-FLASH, I get the red 5 second restart warning, and my pc turns off and upon restart it freezes and does not even start the BIOS update for A.   Hmmmm...  At least I am part way there.  I will try again tonight.  BTW - I do not get a "please set multi BIOS switch to the target BIOS ROM then press any key to continue" dialogue box.  I will advise later tonight my results.   

  • Msi x99 ac power do you have to enable last pci slot ?

    on the msi x99 ac power do you have to enable the last slot? do you have to do something special to get it working ? all the pci lane switches are on

    Quote from: badboy2k on 24-September-14, 09:26:05
    all 3 cannot be x16 as there are only 40 lanes there one is a x8!
    if you have 4 cards it should split them on the x16 slots to x8,x8,x0,x16,x8! if your lower slot is not doing x 8 either you have a bad PCI-E slot or a bent pin in the socket!
    Its not finding the 4th card at all, and it was before, and havent moved it around since. Would a bent pin come and go like that? How do i fix it?

  • How to update my MSI X99S Gaming 7 Bios without loose my raid settings

    Hi all,
    I've got a MSI X99S Gaming 7 Motherboard.
    Last time I used MSI Live Update and I performed BIOS update I lost totally my raid settings ( O.S. HardDisk C is build on my raid 1) and I had to reinstall all from 0. Now MSI Live Update notified me a new BIOS version available, is there a way to perform it without lost my C Drive one more time?
    Thanks in advance for your help.

    Quote from: JLio01 on 03-March-15, 09:17:09
    The only settings should do is after BIOS updating, go the BIOS Settings--Advanced--Integrated Peripherals--SATA Mode switch to [RAID Mode], and everything should be fine.
    Yes exactly, that's usually and typically which has to be done.
    But with some note there are an exceptions from this:
    in the past there was some BIOSes due bugs which caused RAID array lost issue after flashing,
    assume raid was re-enabled after the update,
    but RAID array was lost(didn't recognize the settings) and didn't show and unable to rebuild..
    so its always good to have a backup of important data just in case..
    don't trust too much to technology

  • [X99S Gaming 7] Bios update H80 no ME

    Hi everybody, after updating the BIOS on my X99S gaming 7 motheboard and installed the lastest Intel ME driver (under Windows 8.1 Pro 64 bit) I am no longer able to run any application like Intel Extreme Utility or MSI Gaming App.
    Command Center isn't working too.
    It looks like ME driver were missing during the H80 BIOS update.
    Any idea?

    Reflash it with the following:
    >>Use the MSI HQ Forum USB flasher<<
         A.) Download >>this<< and place it on your desktop. Do not decompress.
         B.) Download and install the Forum flash tool.
         C.) Insert your FAT32 formatted usb stick.
         D.) Make sure that all win 8 options are disabled. (Fast Boot etc) Also make sure the legacy USB is enabled.
         E.) Start the forum flash tool and select option 1. Then point the tool at the compressed archive we downloaded earlier. Then to your USB Flash Drive.
         F.) Boot to the USB 
         G.) Now follow the directions and let the tool flash
         H.) After flashing reinstall ME drivers in Windows: http://download.msi.com/dvr_exe/intel_me10_mb.zip

  • Msi z97 gaming 5 bios update help

    Hello I recently purchased the msi z97 gaming 5 motherboard. It was working fine it came with bios version 1.0 and I wanted to update it. I downloaded the latest 1.5 bios from msi website copied to usb flash drive and flashed it using mflash. Computer powers on but black screen wont do nothing. I cleared cmos and battery and still nothing so I am pretty sure its bricked. I am going to store to exchange it for another one but I want to be able to safely update the bios without bricking again. I usually dont update bios unless needed but i need at least 1.2 bios to fully support the devils canyon cpu. Can someone please point me in the right direction? I read about the usb flashing tool in forum but also read that bios+me need to be flashed and I don't know if that program is up to date and will flash both files? I really appreciate it if someone helped thanks in advance.

    Also does anyone know if it is dangerous to update the bios with a 4690k devils canyon cpu since it is not officially supported until 1.2? Is that why my first bios flash was bricked? I would hate to go and borrow another cpu just to update the bios but if I have to I will. Sorry for all the questions but I need to get my bios updated and I will not update it until I am sure of all these things. Thanks to anyone who answers these questions.

  • MSI X99 AC Power Motherboard 8pin+4pin CPU Power?

    Hello, I just opened my msi x99 ac and I see it has an 8pin and 4pin cpu power near the top, now that is like what my asus extreme 1150 had, however I only have 2 8pins from my 1200w corsair ax. However right next to the 4pin is a little something, so the 8pin wont work because there is no place for the extra 4pins to hang down. How did you guys wire this up? Because before I just use 2 8pins and the 4 extra pins hanged down the side, but it wont work with this mobo
    Thanks

    As far as I can guess, 4 pin is for OC. How do you connect it? I don't know. But I think it will work fine without this 4 pin.
    Check the manual 

  • MSI Z87-GD65 Gaming BIOS Update

    Bought this setup quite a while ago, running a 4670k on the z87 gd65 gaming board and thought about trying a bit of OCing, probably just gonna try out the OC Genie for now, but i was wondering if it would be a good idea to do a BIOS update or is that not necessary? Im still running on bios 1.3 which from what i can see on the msi site is a quite old one.

    Quote from: flobelix on 23-September-14, 01:02:53
    No, 1.3 is too outdated. If wanting to go for latest generation vga get the latest vga (1.B):
    >>Use the MSI HQ Forum USB flasher<<
         A.) Download the attached archive (E7845IMS_1B0.rar) and place it on your desktop. Do not decompress.
         B.) Download and install the Forum flash tool.
         C.) Insert your FAT32 formatted usb stick.
         D.) Make sure that all win 8 options are disabled. (Fast Boot etc) Also make sure the legacy USB is enabled.
         E.) Start the forum flash tool and select option 1. Then point the tool at the compressed archive we downloaded earlier. Then to your USB Flash Drive.
         F.) Boot to the USB 
         G.) Now follow the directions and let the tool flash
         H.) After flashing reinstall ME drivers in Windows:  http://download.msi.com/dvr_exe/intel_amt90_mb.zip
    Thanks Flobelix, running windows 7 but i guess the procedure is still the same, are the ME drivers the chipset drivers? i downloaded the chipset drivers for my OS from the msi site (intel_chipse_9_mb.zip) or is it the "Intel Management Engine Driver+Microsoft hotfix".

  • MSI GT60 2PC Dominator BIOS Update RAID0 problem

    HI THERE , this is my first topic in msi forum and I hope you can solve my problem 
    I have the MSI GT60 2PC Dominator, my laptop came with FreeDOS with E16F4IMS.50Y non raid0 bios version (installed only one msata 128Gb), One day i upgraded my Laptop, I installed two more msata 128Gb. Now 384Gb Raid0 hard disk and i installed windows 8.1 64bit (Working UEFI mode).
    I flashed the bios yesterday to the E16F4IMS.515 which is the latest one but it seems that it doesn't support the RAID0, i didn't care about that, i installed windows 8 but everyday i'm getting several problems with GPU and that blue screen and its really annoying.
    So i tried to upgrade E16F4IMS.715 , But Flash_BIOS_by_UEFI_BIOS_Setup_Utility_e n.pdf this method not supported my laptop (Automatically restart after select bios file.), And i tried too EFI Shell mode bios update. But there is no Afuefix64.edi and FLASH.NSH files in New bios zip file. It has only E16F4IMS.715 file.
    Now my question is How can i flash the bios to E16F4IMS.715?
    Sorry for my bad English and i thanks for your corporation.

    Quote from: Nichrome on 04-November-14, 20:09:17
    Hello and welcome to the forum! 
    Sadly there is only 1 person that is able to help you with flashing procedure, but also directing you to the right BIOS file, and it's Svet. You might have to wait a little bit, as you may already know, it's users to users forum, and we come up when we can and if we actually want to.
    What way did you flash the BIOS?
    I used EFI BIOS utility method. I chose BIOS file and when i click OK button ,  it starts normally after 20-30sec. it doesn't update bios. How ever it works on E16F4IMS.515 (Non-RAID) bios updated successfully. But not working E16F4IMS.715 (RAID0) bios.

  • [Athlon64] MSI K8T Neo FIS2R BIOS Update when? CnQ no workie!

    The MSI K8T Neo FIS2R (MS-6702) hasn't had a BIOS update since 3-4-2005!
    I put a Sempron 64 3000+ in my motherboard, and was very disappointed that it is recognized as an "AMD Unknown Processor".  Sure, it works, but one of the reasons I bought it is in the hopes of getting AMD Cool n Quiet to work.  However, apparently the AMD driver can't recognize the CPU due to the old BIOS on the motherboard.
    Every other MSI skt 754 board supports Sempron E6 revision already.  Why not the K8T Neo FIS2R?  Where have all the MSI BIOS programmers gone?  I have been waiting 2-months for a BIOS update to support the E6 Semprons.  I have asked and begged MSI Tech Support.  I am tempted to switch to ASUS or some other company that is actually timely with BIOS updates.  Only reason I haven't yet, is this board is everything I want EXCEPT for Cool n Quiet not working.  It's starting to look like there is no BIOS update in sight, so I am very disappointed.
    Anyone here work for MSI can confirm there are no plans for a BIOS update?  Because I don't want to wait around for something that's not going to happen.

    Sorry, I didn't mean to imply I thought the mods here are MSI staff... I was just kind of hoping there's MSI staff lurking here, seeing what people think of their products or seeing what people complain about.
    No, pretty much C 'n Q is the only reason I'm disappointed, but it was something I was really set on getting to work since this is a server that's up 24/7, but isn't utilized but maybe 4hrs out of a given day.  I could reduce frequency and voltage, but unlike C 'n Q, it won't automatically increase speed and voltage based on demand - which is something I want since although it's a server, I also use it as a regular PC as well.
    I've even tried the 2.33 beta BIOS with no change, and even found a 5.52 BIOS in their BIOS testing directory.  I guess that BIOS was for a different kind of 6702, although I had pulled out the peripheral modules with AMI's MMTOOL and they looked the same as the existing BIOS, but that BIOS killed my motherboard so it couldn't have been for a regular 6702.  I had to desolder the BIOS chip with a heat gun, reprogram the old BIOS back on it with an EPROM programmer, and solder in a socket.  I guess that shows my dedication to get C 'n Q working!

  • MSI Big Bang 2 Bios Update

    I down loaded the 2.4 bios zip.  Used the msi usb utility to point to drive, restart and run bios update.  Everything shows success except the bios stays the same.  I also ran the me8 driver update and nothing seemed to happen.  Please give me some help thanks.

    Hi
    Normaly there aint any change, that you can see with your eyes in BIOS, Other then BIOS version number.
    Some times there maybe added features, buts thats rear. Mostly BIOS updates adds stable and compatibility.
    Member to clear CMOS after BIOS update, Cheers Mummy

  • MSI P6N Platinum OEM, BIOS update needed

    Hi, I got an p6n platinum oem board, which looks different to the original board by msi. There are no heatpipes inside and the e-sata is missing and it looks like the p6n sli (without platinum). The BIOS ID: MSI P6N SLI Platinum A7350NM7 V1.08 110107.
    Where can I get the BIOS update/is it possible to flash with original msi BIOS update?

    We can not offer support for OEM products. Support is only available for MSI Retail products.
    Remember, there may be slight design differences between the OEM version and the retail version. The retail bios may brick or distabilize the OEM version.
    locked.

  • Msi neo2 p35 + E8500 bios update

    Hey
    i cant update the bios i downloaded the latest version 7345v1a and im told to burn an iso file and then boot up but no files match the iso program when i try to compile. im sorry for typos but im dansih 
    /Fudge

    Fudgeman, please be more specific about your issue.  What is your current BIOS Version?  Why do you need a BIOS Update?  If you have an E0-Stepping processor, a too old BIOS Version and want to update your BIOS because the system seems to freeze up during POST (and does not accept keyboard commands), you cannot simply update your BIOS in a standard procedure.  You either need to put in a supported CPU first or try if the AMI Recovery Routine can be forced to run (for this procedure you need an internal floppy drive and a PS/2 Keyboard).

  • MSI H67MS-E23 (B3) BIOS update error

    Tried update bios on this mainboard but mistaked and download wrong bios .exe updater (E7680vC3 for h61).  EXE file started and proceeded with no error messages. After rebooting pc i get black screen with letters B4 or A2 in bottom right corner. Can someone help me?

    Duplicate Thread.
    https://forum-en.msi.com/index.php?topic=177253.0
    Topic locked

  • Msi gt70 0ne 286tr bios update problem.

    Hello,
    I have msi gt70 0ne 286tr i7 16gb nvidia gtx 680m 4gb, i am using w7 64bit and ubuntu 14.10.
    My laptop came with w8 pre installed. I assume i have w8 bios. I have EFI options on my bios (currently disabled)
    My bios not stable and i want to update. I tried both w7 and w8 bios options but i could not manage to start FLASH program.
    Last time i tried w8 EFI bootable usb stick. USB can boot, i saw device menu but i couldn't see shell>_ so i cannot write anything. It seems my screen resulation not right.
    how can i update my bios? Pls help me. TY.

    I believe it should be possible to update through the BIOS itself as well....
    http://www.msi.com/files/pdf/Flash_BIOS_by_UEFI_BIOS_Setup_Utility_en.pdf

Maybe you are looking for