Msi Z68 GD65 (B3) will not resume from sleep with multiplier above 43

I have an i5 2500k that is otherwise stable (can pass prime95 for hours) at 4.4 ghz, but no matter what I do I cannot get my computer to resume from sleep properly when I go over 4.3 ghz. At 4.3 ghz it resumes from sleep fine, but once the multiplier goes over 43 it simply will not resume. The monitor stays in standby mode, but my PC's fans spin up and my keyboard backlight turns on.
I have tried disabling and enabling pll overvoltage, but it does not help.
It resumes from hibernation fine, but that takes quite a bit longer than resuming from sleep because the POST on this board isn't particularly fast.
This happened both with my previous card (560 ti) and my current card (7950), so I seriously doubt it is a GPU issue. I have a seasonic x750 PSU, so I doubt it is a power issue. I have very good cpu cooling and my temperatures are pretty low even under load. Is this a board defect? I see that ASUS boards had a similar issue that was apparently fixed, but I can't find as much info about an MSI isssue.

Being an experienced OC'er, then you know that trial and error is the tried and true time honored method in the attempt to solve problems. The solution I would recommend is to accept an OC of 4.3, stick with hibernation, or continue with experimentation of combinations of settings, or you can hope someone comes along that 'may' know of a 'solution'.
Quote
I see that xxxx boards had a similar issue that was apparently fixed, but I can't find as much info about an MSI isssue.
Big difference between 'apparently' fixed and actually fixed. You might try MSI Technical, but it may be interesting what they say once they know OC'ing is involved.
>> How To Contact MSI <<
Quote
Thank you for the patronizing response. Does anyone have a response that is actually useful instead of generic "you don't know what OCing does" comments? I have been OCing for years; I know what it does to a system. I am looking for SOLUTIONS here.
Some friendly advice is to watch the attitude, or not many will be inclined to offer any assistance at all. Yours is not a situation that the mainboard is non functional, and is more related to an OC'ing behavior.

Similar Messages

Macbook pro will not wake from sleep without shut down?

My macbook pro 2007 will not wake from sleep without holding down start button and then restarting? Is this a serious problem?

You can Try resetting NVRAM/PRAM http://support.apple.com/kb/ht1379
You can run the Disk Utility> Repair Disk from Recovery ( command R on start)
if that does not sort it I would reinstall OS X

Macbook Pro will not rewake from sleep, but is running?

My Macbook pro with OSX Lion and Core 2 Duo will not wake from sleep. The screen stays black (as if it were off) but I can hear the fans running and the light
on the front stays on steady. I have tried to hold down the power button to shut it off- Didn't Work I have drained the battery and restart- Didn't work

like mine... http://www.youtube.com/watch?v=C-ZFewhxYi0

MacBook pro 17" will not wake from sleep mode

Ok so my MacBook Pro 17" with osx 10.6.8 will not awaken from sleep mode. when attempting to wake it up the screen dosent come on and the mouse and keyboard do not receve any power. to get back on the computer i have to force a hard restart by holding the power button for 10 seconds then pressing it again. then it boots to where i left off when i closed the lid. i have read a few forums about this problem and i have went through all the steps of reseting various things and went as far as going into terminal using sudo to disable safe sleep and nothing helps. i noticed an unusual error in my console. here is a copy of my console log. the one in question is {7/14/13 4:52:43 AM com.apple.UserEventAgent-Aqua[118] dontAutoLoad = EMPTY!} someone please help me I am over 150 miles from the nearest apple store or authorised retailer

Active Profiles:
Battery Power                    -1*
AC Power                    -1
Currently in use:
halfdim          1
sms                    1
hibernatefile          /var/vm/sleepimage
gpuswitch          2
disksleep          10
sleep                    0 (imposed by 223)
hibernatemode          3
ttyskeepawake          1
displaysleep          5
acwake                    0
lidwake          1
Also I broke down and called support again this time a senior advisor's boss recorded the events and sent the data to their "engineering department" still waiting on the results hopefully they will get back to me sometime between today and saturday. will post the results of the tests. also this is a 2011 17in intel i5

IPhone 1.1.4 will not wake from sleep mode

Hi all,
I have an iPhone with 1.1.4 firmware. The problem that I have is that the phone will not wake from sleep mode by pressing the "home" button. I have to press both the "home" and "sleep/power" buttons and hold them for 6 seconds for the phone to restart. I did restore the phone twice - did not solve the problem. Then, one day, I left it charging for about 3 days and when I came back it started working fine. Not for long though( After about a week of normal usage the wake up problem came back. I don't know what to do. I don't think it's the software problem, since I did complete restoration 2 times.
If the phone is connected to a charger or computer - it wakes up fine.
Thanks, Gene K
Message was edited by: rimini

rimini,
When you've restored the iPhone, have you tried setting it up as a new phone? This would truly eliminate software as a possibility.
If setting it up as a new phone doesn't correct the issue, it's probably time for service: apple.com/support/iphone/service/faq/
Hope this helps,
Raleigh

IPhone will not wake from sleep and locks up with new MMS update

Hey everyone,
Has anyone had these problems with their new update as well?
1) Sometimes my iPhone will not wake from sleep mode, I have to hold down both buttons for it to restart...I do this about 5 times a day!
2) I cannot send SMS messages and when I send more than one sometimes the iPhone locks up and will not unfreeze.
Does anyone know if this is an Apple update issue or if it is an AT&T issue? And if this is being addressed?
Apple, if you read this could there be an update to all members what is going on?

I am experiencing the same issue with iPhone 3GS. After yesterday update to 3.1.2, it is a bit better in the sense that I can restart the iPhone slightly faster but still getting frozen screen during a call. I will try to call support once more. I don't believe that the problem is solved in the new update.

HP 15t j000 will not wake from sleep/hibernate Windows 8,8.1,10

HP 15t j000 will not wake from sleep/hibernate Windows 8,8.1,10. I have to restart. I've searched high and low for answer to this. I've seen videos, played with power settings. I hoped each Windows system upgrade would fix the problem. No go. Anyone with any ideas?

Hi , Thank you for your query. I understand that after upgrading to Windows 10, it will not wake from sleep mode unless you restart. The first step I would try is to disable "Hybrid Boot' or "Hybrid Shutdown. This can be done by turning off "Fast Startup" Fast Startup - Turn On or Off in Windows 10 Next try running the "Update Troubleshooter" Windows Update troubleshooter. Once launched, it should show a screen like this. Use the second option "Background Intelligent Transfer Service", it should lead to a force update of 'Windows Updates' that may not be automatically being applied, that could fix some of these issues.
Here is a link to HP PCs - Sleep and Hibernate Issues (Windows 10, 8) that may also help. To say thanks for replying please click the thumbs up button below.If this yielded a solution please choose solution provided to help other people find this information. Best of Luck!

My macbook pro 2.0 early 2011 will not go to sleep with the power source connected. only enters sleep mode when running on battery. Someone did this happen, and it could solve?

Alo, my Macbook pro i7 2 GHz Intel Core i7 (early 2011) will not go to sleep with the power source connected. only enters sleep mode when running on battery. Someone did this happen, and it could solve?

There is no output from that command line? Maybe the pid changed.
I'll repeat what I am trying to find out...
1. You do a pmset -g on the terminal.
2. The output from that pmset should have a line that says "sleep 0 (imposed by n)" where n is some number.
3. The ps ax | grep n is supposed to display what the process associated with n is.
It's the output from step 3 that should indicate what is causing you not to sleep.
But speaking of sleep, that's where I am going.

Will not wake from sleep mode

When I close then open the lid on my MacBook, it will not wake up from sleep mode. I have to reboot by holding down the power button for 10 sec. When it restarts, it takes a long time to get past the gray screen with the apple logo. I also have this same problem when it goes into sleep mode, when left idle. I have since changed the settings so it will not go into sleep mode when idle in system preferences. I have reset PRAM and SMC, but the problem still persists.

I have the same problem, intermittently. I think it has something to do with full-screen mode, which I use intermittently. Have you noticed this happening only when you are in a full-screen app?
I also have a MacBook Pro from 2011, and I know for sure my MagSafe power adapter is fine and not part of the problem.
I have noticed a few things that may be hints at what is happening:
one time, (all??) while my screen was basking in the glow of sunlight from the side, I saw that the screen pixels were indeed "on", that the back-light of the screen was just off.
Which led me to the conclusion that my MacBook Pro was indeed waking from sleep, the screen was just not lighting up.
But that theory was disproved this morning, when when waking from sleep, the screen was black, except for my cursor. My cursor was completely visible on a black background. Huh?? It was like some software was putting up a black modal dialog over the whole screen. Also, the Apple Logo on the back of the laptop screen was fully lit -- meaning the backlight was on. The machine was awake (curson moving on a black background), and the screen was fully back-lit.
I'm not sure yet how consistent this behavior is... I will take more careful notes each time this problem happens in the future... But, it looks like I have rogue software that is trying to make my machine look like it is sleeping.
To "capture" the culprit I think I could set up a hot-key command that takes a snapshot of all running processes in Activity Monitor. This could show what processes are running when "waking" from sleep. nabbing the culprit?
I use Snapz Pro. That is non-standard software running with control over screen functions. Maybe Snapz Pro has a problem? I doubt it, but maybe, because it has hooks into background tasks with video. Snapz Pro is my only 32-bit process. Could Snapz Pro be the cause? I use Snapz Pro all the time.
The problem seems to be related to Full-Screen mode. Could it be possible that full-screen apps sometimes have problems returning from sleep? I know there are viewControllers responsible for handling events when waking. Could the symptoms of not waking from sleep be caused by bugs in full-screen apps?

X61 will not resume from standby/screensaver

If the screensaver is enabled with password protect and it goes into screensaver, when resuming there is no login window or fingerprint software. Mouse pointer is the only thing available. Hitting Ctrl - Alt - Del will not bring up anything. User has to restart laptop to log back in.
This is an X61 - 767374u running Thinkvantage Fingerprint Software v5.6.1.3425. There are two updates available to this software, v5.6.2.3650 and v5.8.2.4462 but neither say it fixes the standby/resume issue.
I know for sure this was a known issue on the t400's running Lenovo Fingerprint software v3.2.0.99 and lower.
Any ideas?

Ok, so I updated the software with v5.6.2.3650 and then v5.8.2.4462. Fingerprints still worked, nothing got erased. Left it alone for a while and noticed that the screensaver didn't kick in this time.
The user is going to test it for a few days and see if does it again.

IMac will not wake from sleep after 10.4.8 Update

Recently after a couple of software updates my IMac goes to sleep and the Bluetooth keyboard and mouse will not wake it. The option for wake with Bluetooth is checked. I zapped the PRAM and also checked the HD, Nothing has changed. NOTE: No new software or hardware installs were done except for 10.4.8 update and the other mac software updates. This did not happen in prior versions of the OS on my iMac. Is this a new bug?
iMac G5 1.8 (pre iSight) Mac OS X (10.4.8) Bluetooth, Wake from Sleep

I've been dealing with this same issue, have tried everything, but to no avail. After MANY sessions on the phone with Apple tech support, as well as an Apple product specialist, I was advised to erase my computer and do a fresh install. I did an archive an install, which didn't help, but am not thrilled about the prospect of erasing everything and starting over. This problem started after the August 2006 round of updates. I feel it's bluetooth related, because I used a usb keyboard and mouse for a week as a test, with no problem. The funny thing is, I unchecked "allow bluetooth device to wake computer" thinking it might help, but the bluetooth devices continue to wake the computer anyway (except when it refuses to wake, of course!)
Jerry

Monitor will not awaken from sleep

PowerMac G4 Dual 1GHz Quicksilver. OS 10.5.2, Apple Cinema Display. After sleeping, monitor will not awaken. Display is visible when screen sharing from another computer. Requires restart.
Recent changes:
Started using Time Machine on an existing internal drive.
Installed a Time Capsule Airport Base Station in the house.
Started using the built in Screen Sharing software.
Upgraded to 10.5.2.

Here's the basic steps , including checking the parameters. My all time favorite, using reverse logic (sometimes).
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

MacBook Pro will not wake from sleep

My new 13" MacBook Pro will occasionally refuse to wake from sleep. Touching the keyboard or moving the mouse will turn on the keyboard background lights but the computer will not wake. This occurs without any peripherals attached. I have reset the PRAM and the SMC ... no help.
The only option for recovery is the hard power down with the power button and restart. Anyone else seeing this?

Yes and I hate it. I am having pretty much the same problem, and have tried the same solutions, also Iupgraded to Lion and there still has been no relief. My computer just runs slower.

Dual 1.25 mdd g4 will not wake from sleep

if i leave the comp on and it goes to sleep or if i force it sleep, it will not wake, the power button will not pulse its stays on solid, the display shuts down, but when i move the mouse nothing, if i click the mouse it will light up red only when i click it after that i goes back out, the display stays in sleep mode, i have to hold the power button down till it shuts off then restart it and it starts and runs fine till it goes to sleep then i have to restart
any help would be great, thanks

Well I'm having a combination of a number of these issues. Background is dual 1.25 GHz with OSX 4.11. Current situation is that the computer will not wake when put to sleep. This will happen whether I select Sleep from the Apple menu or just let the thing time out and put itself to sleep. I haven't been able to narrow it down but if I don't wait too long after sleep it seems I can log back in (even though during sleep the power light is only dim and doesn't pulse and the fans keep running so it doesn't really seem like "sleep"). Mostly the power light dims when in sleep and then is unresponsive requiring a hard reset. The most recent development is that after some time instead of going into this nebulous sleep state the computer just shuts down altogether, just like a hard crash, and I have to restart and reset the clock.
I've read many of the posts regarding problematic PCI USB cards and I did have one which I removed, but this didn't have any effect. I've reset the PMU to no effect. I should also point out that the USB ports on the back of my Apple Cinema Display don't work now either and I have to plug the keyboard directly into the Mac (though I can boot the computer from the power button on the keyboard).
Any knowledge or suggestions would be great...

PowerBook Will Not Wake from Sleep - Horizontal Lines on Display

I have a new PowerBook that I purchased last December. When my computer goes into sleep mode, it will not wake up unless I do a hard poweroff by holding in the power key for 5 seconds. When it tries to wake from sleep all I see is my mouse cursor on a black screen or the spinning beach ball. I'm also having problems with graphic applications such as Photoshop or Adobe Illustrator where I'm using lines that are only 1 pixel in length. The lines disappear when I drag them across the screen as though I'm missing a whole row of pixels or half of the line is fainter. I also notice very fine horizontal lines throughout my display. My older PowerBook does not have these lines nor this wake from sleep problem.

Contact tech support, it will need to be sent in for repair, and as long as your hardware warranty is good or you have APP the repair will cost nothing. unfortunatly this is basically your only option, unless resetting NVRAM takes care of it. to do that turn off com. hold down option, apple(2 key's left of space bar)and o, f, then turn on while holding those down. when firmware opens up type in reset-nvram, press enter then type in reset-all(include the dash in both)
this will reboot com. if this does not take care of it a repair is needed.

Msi Z68 GD65 (B3) will not resume from sleep with multiplier above 43

Similar Messages

Maybe you are looking for