MSI Z87-GD65 and ram compatibility

Hello all,i would like to know if Z87-GD65 board is compatible with new Kingston HyperX Fury memory?
I can't find answer anywhere so i u could help me,this model HX318C10FBK2/16. In fact i would like to know if there would be any problem with memory with cash latency 10 or 11?

I checked the specs here http://www.kingston.com/datasheets/HX318C10FBK2_16.pdf
There is nothing out of the ordinary. It may not have been tested by MSI for this board yet. Thus the timings at 1866 may not automatically set correctly. But you have the option to set them manually.
Memory that's not on the support list is always a bit of a gamble, but mostly if standard JEDEC settings are applied, it works.

Similar Messages

  • MSI X79A-GD65 (8) Ram Compatability

    hello gents
    I'm planning for my new rig with the MSI X79A-GD65 (8).
    I found in the memory compatibility guide page 7 that the "G.Skill [RIPJAWSZ] F3-12800CL9Q-16GBZL" kit that has 4 dimms as advertised.
    filled the 8 dimms in the test
    does it means i can use two kits of this with no problem???
    please advise cause i'm on a harry to buy.

    Quote from: aelghattas on 19-July-12, 03:48:48
    I'm planning for my new rig with the MSI X79A-GD65 (8).
    I found in the memory compatibility guide page 7 that the "G.Skill [RIPJAWSZ] F3-12800CL9Q-16GBZL" kit that has 4 dimms as advertised.
    filled the 8 dimms in the test
    Quote from: HU16E
    If you are going to fill all 8 slots, you are better off getting an 8 stick matched and tested kit. Reason, mixing kits even though the same part number may have different chips on them and not be compatible with each other. That particular RAM manufacturer even has some disclaimers about that with some kits.
    That's right.
    http://www.gskill.com/products.php?index=427
    3. G.SKILL guarantees module compatibility within this specific Quad Channel kit. Combining with other memory kit or module (even with same part number) is not recommended to avoid any compatibility issue.
    In fact, 8 memory modules is not a good idea at all.
    There will be a huge bandwidth demand and you'll need to raise the voltages and/or to slow them down.
    Otherwise you'll get into stability issues.

  • MSI Z87-GD65 and Z87-G43 problem on first reboot

    Hi,
    I have got the 2 motherboard in the subject and I have the same issue on both!
    Basically I switch on the PC and after the logo of the mainboard my PC just automatically switch off with a small bep, then when I try to switch on again, everything works normally as it should be.
    I have some doubt that can be related to the ram, but... it is strange that for 2 months was ok and now start to do it on the second motherboard as well.
    My main config is :
    Z87-G43 bios 10.4
    i5 4670k
    ram cmx12gx3m3a2000C9 but I have installed just 2 dimm so I have 8GB into the slot dimm 2 an 4
    VGA MSI 770 gtx
    PSU corsair 600cx
    no overclock but just the XMP profile activated.
    On the other config
    Please could you help me?
    Thanks

    Since it's happening on two separate boards and during bios boot I don't believe it's driver related nor board/s related. I have the Z87M-G43 with no issues, so that leads me to believe it's either your PSU, or ram, or possibly an errant install in your case (eg. missing a motherboard standoff). Try another PSU see what happens, Also try different ram. In theory your PSU should be ok with your 770 GPU but it might not it could be a slightly defective unit with an out of spec +12v rail. The only way you are going to find out the issue is by testing components. You can find out if your GPU is ok by trying it in another machine. Ram too. Power supply as well. If you have a decent runnable PSU laying around I would set your rig to the lightest possible config using your Intel integrated GPU (no GTX card) just to see if you can get a decent boot.

  • MSI Z87 GD65 ,best RAM

    Hello.
    I'm just about to purchase the staged MB,but was wondering what speed RAM I should buy.
    I won't be over clocking the RAM ,I just would like some RAM of a supported speed
    I was going to buy some 1600,but saw some 1866 and 2133.
    Would either of these work with this board ,ideally without changing any of the RAM settings
    Thank you

    Quote
    I'd recommend this beautiful pair: G-Skill Ares 2x8GB 1600Mhz F3-1600C9D-16GAR
    Series Ares  Memory Type DDR3  Capacity 16GB (8GBx2)  Multi-Channel Kit Dual Channel Kit  Tested Speed 1600MHz  Tested Latency 9-9-9-24-2N  Tested Voltage 1.50v  Registered/Unbuffered Error Checking Non-ECC  SPD Speed 1600MHz  SPD Voltage 1.50v  MSI Mainboards do well with Corsair memory modules.
    MSI mainboards do well using Corsair memory modules.  Recommend a kit of them instead. 

  • MSI Z87 GD65 Crashing/Freezing/No Monitor Signal

    So the other night I was playing WoW for a few hours... When I woke back up and turned my computer on it booted up... The fans kicked on/keyboard and mouse lite up and the screen said no signal. I shut it down pulled the power for awhile then booted back up. Then booted it back up and everything was fine when I opened wow and logged in 2 second later the computer rebooted it self. When rebooting the computer the screen said lost signal to the monitor again and the only way to get that back on is by pulling the power cable.... It would also freeze time to time....Now the computer wont even show the screen... What is faulty? MB/Graphics card? Im using MSI Z87 GD65 MB and the MSI 770 Twin Forzr 2gb.
    Things I tried
    Reformatting
    Resitting Graphics Card/Ram
    Switching Graphics Card on a different slot
    Different driver
    Canned air for cleaning

    I tried clearing the CMOS, the graphics card fans are running but not sending signal to the monitor, I took it out and using on board... that works fine... Im trying to figure whats the problem is before I go purchase the new part.
    My Rig
    CPU- Intel Core i7 4770k
    Motherboard-  MSI Z87 GD65 Gaming
    Ram- Kingston Hyperx Beast 32gb 1600Mhz
    Cooling- Cooler Master Seidon 120XL Liquid CPU Cooler
    Power Supply-Cool master v700
    HD- Samsunng 256 SSD

  • MSi z87-gd65 OC Genie and RAM frequency issues

    Hey all,
    I just built a new computer (my first build), and am quite glad with the capabilities of the machine. However, whenever I try to turn on OC Genie or bump up my ram speed to 2400 MHz(I believe this is the native speed, but the motherboard puts it down to 1333MHz) the system fails to boot, and sometimes hangs in a rebooting cycle. Eventually, the motherboard gives an error on the screen saying that the changes made have failed and was restored to default settings, and to press f1 or f2.
    I admit I am a complete novice at overclocking, and probably do not know what I did wrong. I've updated the bios, cleared cmos, and tried both bios A and B, but have got the same results. I was hoping I could get some help on this forum and learn new workarounds! Any help is greatly appreciated.
    My Build:
    i7-4770k @ stock frequency
    MSi z87-gd65
    Corsair H100i
    SeaSonic Platinum SS-860XP2 860W 80 Plus Platinum Certified
    Samsung 840 Evo SSD 256 gb
    Corsair Vengeance Pro 2400MHz CMY16GX3M2A2400C11R

    Quote from: phantom24 on 19-October-13, 08:56:19
    Hey man, thanks for replying. The first thing I tried, before overclocking, was to enable XMP from the UFEI. When i enabled it, the board would show that memory was OC'd to 2400MHz and bumped up to 1.65 voltage. This is all shown prior to rebooting. When I would reboot the computer however, the system would fail to boot and I would get the same error saying all "overclocking failed, reset to default settings". I believe that my ram is the cause for my inability to overclock. I found out that motherboard is not compatible with it at extreme speeds. The max speed I can get out of my ram is 2133MHz with no problem whatsoever in rebooting. This is without changing the voltage of the ram( keeping it at 1.5v) . If I change the ram voltage, I'm pretty sure it would fail to boot.
    Yeah good luck with OCing and please let me know if you find anything useful. I'm afraid that this forum does not have much to offer, so you may want to try some other forums.
    Jms and Xfx are right. By default mine booted to at 1600mhz. I enabled XMP and it brought it to the rated speed of 2133mhz. I'm not trying to overclock my ram further than the rated speed. Pointless to me, considering I'm coming from a rig that had ddr2 with 800mhz. As you can see in my pic, the one with blue LEDs is the 7.5 year old build. Still going strong. Anyhow, if you do overclock, make sure you disable the XMP. That way you can eliminate another possible instability issue. I'm a member of a few forums, and I was suprised to see these forums not respond very well. For the guys who did respond, I thank you! You may also want to check out overclock.net   There's are plenty of people there and "clubs" you can be a part of. I'm finding a lot of useful information there. Most people won't get mad about noob questions unless you do like me and ask the same ones in multiple threads lol! Hop on over there and check it out. My name there is Scotty Mac.

  • MSI Z87 GD65 Gaming and msata speed issue...

    Hi,
    So I'm running the MSI Z87 GD65 Gaming with a 128GB SanDisk msata. Now it all works perfectly; no BSOD or crashes, but what I have noticed is that sometimes when the PC boots and I look in Intel Rapid Storage Technology, the msata on port 5 is running at 3Gb/s not 6Gb/s: I verified the speed loss using AS SSD benchmark. Reboot and it's back to 6Gb/s and back to full speed.
    Anyone else seen this or have an idea of a solution?
    Thanks

    Quote from: JLio01 on 06-March-15, 14:21:58
    How often can you notice the problem? You mentioned AS SSD Benchmark has speed loss, what's the result of speed test then?
    I notice it a couple of times a day minimum

  • Flashing of MSI Z87-GD65 GAMING failed and dual bios not helping, not sure why?

    Hi all
    For the first time in 20 years Ive had a firmware flash fail it seems.
    I have a MSI Z87-GD65 GAMING and updated the bios with the latest firmware via the "M-FLASH" utility within the systems bios.
    All seemed to have gone well, it flashed to 100% rebooted and then just a blank screen and a sequence of keyboard light flashes.
    After a minutes panic I thought not to worry, the motherboard has a dual bios.   So I powered down and switched the bios switch to bios B hoping it would assist and the problem is identical.
    Any tips anyone?

    I just tried this along with removing power from the main board and it seems one of the two did it!   thanks

  • Checking ram that works with MSI Z87-GD65 GAMING Intel Z87 Motherbo

    Was wondering if Vengeance pro series 16GB (2 x 8GB) DDR3 DRAM 2400MHz C10 Memory Kit (CMY16GX3M2A2400C10R) will work good on MSI Z87-GD65 GAMING Intel Z87 Motherboard or if im gonna need to do some tweeking.

    Since in the components purchasing stage for the project, a few tips for you. Check with the PSU manufacturer to make sure it is Haswell compliant. I like single rail +12V PSU's made by Corsair, but there are other good ones out there too. OS is also important. I prefer Win 7 Ultimate 64 Bit, but if you go with Win 8 or 7, some GTX 780 issues may arise. GOP, VBIOS, mainboard updated to the very newest UEFI/BIOS etc. can be involved. UEFI/BIOS update is a good place to start if the graphics card gives you trouble. Research as much as you can prior to the build. Advance planning helps a lot on what to possibly expect.
    Here is the thread for UEFI/BIOS's;
    https://forum-en.msi.com/index.php?topic=169827.0

  • Msi z87 gd65 gaming and Kingston 120GB SSDNow MS200 mSATA Drive

    Hello i have mainboard msi z87 gd65 gaming
    my question is  this  Kingston 120GB SSDNow MS200 mSATA Drive [SMS200S3/120G] is compatibily with my mainboard ????
    http://www.kingston.com/us/ssd/s/#sms200s3
    http://www.visionstudio.gr/prodinfo.asp?id=34204&cat=6
    i w8 .ty
     

    should be

  • MSI Z87-GD65 DRAM & DIMM Voltage Readings

    Hello everyone.
    My spec is:
    i7 4770K @ stock for now
    MSI z87 GD65
    G-skill RipjawsX 1866 Mhz
    My question is; I'm using 2 softwares for monitoring stuff. One is HWMonitor and the other is HWInfo64. And I've found something confusing lately. In HWMonitor, it shows my DRAM Voltage @ 1.48v but in HWInfo, it shows my DIMM Voltage @ 1.69v. BIOS shows it's @ 1.488v but most of the stuff is set to auto and I never be sure what's going on there. So I'm kinda confused since I'm only using the XMP Profile 2 and it should be around 1.5v. But with HWInfo showing it @ 1.69v I want to know if something is wrong or not. Any suggestions?

    Quote from: Sea Dog on 17-January-14, 04:43:15
    What does HWInfo64 show for DRAM V. when XMP is disabled and the RAM is running default? There could be a programming issue with the SPD/XMP profile reading of the software and/or the way the BIOS is reading the RAM's profiles. Sometimes these anomalies can be rectified with a UEFI/BIOS compatibility revision. The RAM brand is well known for SPD profile problems on a number of  different mainboard brands.
    HWInfo64 still shows 1.696 with XMP is disabled and the ram is running 1600mhz.
    HWMonitor on the other hand shows it @ 1.48v even with XMP is enabled.
    Quote from: xmad on 17-January-14, 06:01:45
    I would believe what it says in control center / command center.
    If there is any doubt, verify it with a digital multi-meter.
    I couldn't find where it shows the DRAM voltage on command center.

  • Msi Z87-GD65 Booting Failure With eSATA Drives

    Hi Folks,
    Before I go down the (probably ill-fated) Customer Service path I thought I'd address the forum here on a little problem I'm having with my Z87-GD65.
    IN essence, if I have a hard drive connected to my eSATA port the PC won't boot.  I'm using an ICYDOCK 4 bay external enclosure (MB561US-4SB if interested).  If the drive itself is on but the HD trays are ejected then it boots.  If any of the drives are secured then it'll hang at a post-BIOS/pre-Windows screen where all I get is a blinking cursor for about 30 seconds and then it disappears to a plain black screen.  If the device is powered off then it boots.
    I've checked the BIOS with one of the HDs running and it doesn't appear within my boot list - in fact, except for one selection in the bios allowing me to disable eSATA there really isn't much I can do there.
    I've upgraded my BIOS to 1.30 from 1.00 and the process seems to move a bit further - now I get the oh-so-pretty ugly Windows logo and that's all.
    When I do actually boot the PC with the ICYDOCK off then I'm able to get into Windows normally, and turn on the ICYDOCK.  After a few seconds all 4 hard drives report in and everything's fine.
    I've been using this ICYDOCK for about  a year and a half, with 2 other motherboards (neither were an MSI) and i7 cores, and neither of them caused me any issues.  I remember that neither of those boards had the port multiplier eSATA capability so I had to buy a controller card with that capability.  I could probably dig that up and see if the problem remains.
    In case you're wondering, if it helps, I built a Msi Z87-GD65/4770 i7 - based PC with 2 internal 2TB Hard Drives, and 16gb RAM.  I already mentioned the ICYDOCK.  I used LiveUpdate to install all the latest drivers & BIOS before uninstalling it.
    I build & repair PCs for a living so I'm pretty familiar with what's going on with the system.  I figure that there must be something happening between the BIOS and Windows "handoff" of the ICYDOCK, but I'm damned if I can figure out just what.

    More information please. PSU, OS being used, etc..
    Live Update is best uninstalled. Flash UEFI/BIOS the safer way;
    https://forum-en.msi.com/index.php?topic=169827.0
    Recommend to download drivers and utilities from the MSI Websites and install manually.
      >> Posting Guide <<

  • MSI Z87-GD65 Gaming Motherboard Booting Windows 7 Trouble

    Hi guys, today I bought the MSI Z87-GD65 Mobo, 2 Sticks of 4GB RAM and the Intel i7 4770. I bought these to upgrade my old system and the only other parts im using is my Nvidia GTX570, PSU and my 2TB Seagate HDD.
    Everything hardware works normal, no abnormal signs.
    My problem is when it boots up, it says "find --set-root --ignore-floppies --ignore-cd /win7ldr. Error 15: File not found"
    I've tried using my windows 7 disc and it says all my stuff is still there and the startup troubleshooter doesn't find any issues. I tried putting my RAM in properly and its in nicely. (they are in the 3rd and 4th slot though) My power is fine, its just the BIOS isn't booting it =(
    -The BIOS is updated
    -No Hardware faults
    Note: when i press any key to continue, it comes up with GRUB4DOS and has options like: "Windows 7 with SLIC Loader (Default)"
    Please help me if you know anything!

    Hi,
    Quote from: TrisXD on 15-July-13, 20:12:10
    Its a fresh install of Windows 7, i had to do it to fix my original problem =/
    Update: I changed the RAM and put them in the slots u suggested, no change.
    Sorry, when i post my last anser, i didnt know your new problem
    Sounds like old problem from time of XP to Vista.
    Firsth. Take out that USB connection of your headset from PC.
    Secend. Uninstall any driver that headset (or you) may have installed to your OS.
    Third. Run registercleaner program.
    Fourth. Shotdown PC and then start again (dont just reboot!)
    Fifth. Download and/or Install drivers for that USB headset.
    Sixth. Reboot that PC.
    Seventh. Insert that USB connection.
    I hope this helps! Cheers, Mummy
    If not i would try to ubdate intel chipset drivers(if MSI ones dont work, i would go to Intel site and try them from there) and if those dont help then another reinstall of OS and member to inser USB device after installing drivers for the device.

  • MSI z87 gd65 no post, no code

    Hello,
    I got this problem with my msi z87 gd65 mobo. It doesn't want to post (no screen or whatsoever). It doesn't give any debug code. And it only starts up when i hold down the start button. I used a 2nd psu as the psu is the problem most of the time but that didn't fix it. Also the no debug code makes me worry about it. I did recet the cmos with the reset cmos button, and that didn't fix it. also no overclocks.
    cpu: i5 4670k
    gpu: evga gtx 770 sc acx
    ram: G-skill ripjaws 2x4gb 1866mhz
    cpu cooler: corsair H100i

    still nothing :s also if i want to shut it down i have to hold down the start button, same things happen. need to hold in start button and no post or debug code

  • MSI Z87-GD65, Freezing while gaming, then reboot loop/bsod/total failure.

    Hey fellow MSI'ers
    Im hoping to find a solution for my problem i have been getting. I build a custom gaming rig a few months ago (specs below)
    Sinds a couple of days iv been getting wierd problems, System runs fine, i can do everything watch movies do work stuff. But when i start gaming it will work great for about 15-30 minutes, then i hear a click/beep thru the sound system, and a total pc freeze, screen freezes nothing works.
    So i hit the reboot, then the system decides to turn itself off and get into a reboot loop, turning on for few seconds then turning off again for a few back on for a few, etc etc.
    Only way i can get it running is pull the power, make sure the Motherboard has no charge left, then wait a bit and replug the power. Most times it will boot up fine and story starts at part 1 again.
    First off i thought it would be temperature, tho im running a almoost ull watercooled system, (Ramm + cpu + video) and i put up temp controlls on my seconds screen, and they never got above 35, on any of the components.
    Now seeing my build it is extreemley hard to quickly test a diffirent component, been running memtest with no problems, But when i do graphx/cpu stresstest/benchmark i get the same issue.
    As i stated before it has been running perfectly for few months.
    I read that PSU might be a problem, compatability wise with Haswell, tho then it wouldnt have worked for so long and just now giving these strange problems.
    What i tryéd so far:
    -Reinstall windows
    -Flash bios
    -clear bios
    -unplug as much as possible
    -diffirent ramm
    -Running with or without crossfire enabled.
    All same problems, i hope somebody has a idea without having to pull apart my custom build.
    Specs:
    -Cooler Master HAF XB
    -Intel Haswell 4770k
    -MSI Z87-GD65
    -2x Asus 7970 in Crossfire.
    -Corsair Dominator GT 2x4gb
    -Corsair ForceGT 128GB SSD
    -Antec TruePower 1200
    -2x 512gb Seagate MomentusXT

    Hi again,
    Quote from: robinvanesch on 03-October-13, 04:33:35
    UPDATE: Been running bencharmks/stresstest from onboard graphix, both cards disconnected. (lots of towels to be sure) and runs without problems, tho reallo low fps but thats expected.
    Going to see if i can run 1 card at a time, see if i can cause the problem to happen again.
    So did you agtually try it?
    Yep, bleeding is nice job and dooing it right on all steps is needed so yeah great, but if your CPU can handel the stress and you have tested the PSU then i cant see other way.
    Tip: take the hard loop,pipe, bridge(betwean the blocks away and add two 90angle fittings with long tobe, so you can rest each card away the pc 1 at time that way you dont need to bleed the system bitwean.
    (allso rest of the toops needs to be so long that it can be far away...)
    And yes you need reg edit your SATA drivers like xmad sayd, if you like to change IDE to RAID.
    P.s. nice build! Hope you get it working 
    Edit: You dont need to insert that PSU in the case, just connect wires whrere they need to be, at the momen for testing.
    Edit2: My current needs little service and update( add backplate, water change, delid cpu and moving GPU to bottom slot).
    Edit3: Wait that one 120mm low Rad keeps your sytem 32c??? Damn you have great chips, cold house or software issue. need for delid main is the heat i dont like and i have hmm 10 times that space to get heat off :D

Maybe you are looking for

  • Shuffling songs & audiobooks in a playlist

    I'm trying to put together a playlist with short stories downloaded from iTunes and songs (also downloaded from iTunes). I am wanting to play this mix in a shuffled fashion. The problem is that the stories are marked as not to be played in shuffle, w

  • I downloaded the latest iTunes and now it doesn't recognize my iPhone

    I downloaded the latest iTunes update and now it doesn't recognize my iPhone

  • Some problem,please a little help

    Hi everyone, I set the path in a file called jinit.bat saying c:\jdk1.3.1_01\bin,i am able to compile & run the program but i am not able to edit the same program or any other ,if i say edit JJJ.java it is saying ,bad command or file name ,i am not a

  • Documentation(how to) for provisioning AD --OIM-- DB

    Hello all, Where i can find some "how to" about provisioning AD<--OIM-->DB? I need to install this resource , but i don't know how ? I didn't find (more difficult to me) a kind of "how to" about OIM-->DB provisioning. Thanks a lot.

  • Vault in 1.5 - a copy of your "referenced files"?

    In 1.5, as I understand it, your image files don't have to be in your Library, they can be stored where you like. In that case, when you make a backup via Vault, does it include copies of your images, or just the metadata describing where they are?