MTP USB Device did not install

New PC, Windows 7, Office 2010, My Blackberry desktop software does not see my 9530 Storm I've downloaded new desktop software, but keep getting an error that my MTP USB device did not install when I connect my 9530 to the USB Port.

BACK UP YOUR REGISTRY!!! Editing the registry can be (read: IS) dangerous and can cause no end of pain if done incorrectly.
- To Back Up your Registry: Click START menu and click RUN. Type REGEDIT. Click File, then choose Export and type a name for the Registry Backup, something like REGBACKUP012015 or whatever works for you.
- Click Export and let it export the registry to a file.
- To fix the issue: Follow the folder tree on the left to: HKeyLocalMachine > System > Current Control Set > Control > Class
- Find {EEC5AD98-8080-425F-922A-DABF3DE3F69A} down the LEFT hand side and click on it.
- Under the list on the RIGHT hand side find UpperFilters
- Right-Click UpperFilters and click Delete
- Close the registry editor and restart your PC (without the iphone attached).
- Once restarted and logged back in, plug in your iphone and voila! Windows will actually choose the correct driver.

Similar Messages

Curve 9220 BlackBerry App World registration error MTP USB Driver is not installed

Hi,
Recently I have purchased Curve 9220, trying connect to BlackBerry App World setup in the first instance I get
1. Get the BlackBerry App World Browser Plug-in (I get tick mark) then when I get
2. Connect your smartphone I get the drop down of my pin no I select my PIN no here I get a error message (An error has occurred communicating with the BlackBerry App World Web plugin. Please restart your device and try again. If you have content protection enabled on your device, please disable and try again.)
I have tried rebooting my device no of times it does not work.
I have removed all USB driveres thats was there in PC rebooted the system it is still not working.
I have even tried in another PC having win7 it gives error message MTP USB Driver is not installed.
For information Content protection is not eabled the encription is not ON in my hand set
Another problem whenever I connect my deice to USB every time it takes up the driver asks me to reboot the sytem (I have even tried the same 4-5 times) still not wokring.
The hand set is communicating with the BlackBerry desk top software (I have downloaded the latest one and using the same).
I need to install few apps which was there in my earlier BB so please help.
Best regards,
Shaibal Ghosh

Hello shaibalghosh,
Welcome to the Community,
As you having difficulty in connecting to apps. world , On your Homescreen Go to Options > Security > and check
encryption is disable For your device and Media card and also Check Firewall it may prevent connecting Apps
World.
Please have a look at this article of KB Apps world web plug-in error appear when attempting to install applications from a computer
Try installing OTA .
Good Luck
Prince
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

Apple IPod USB Device Driver Not Installed? WIndows not reconizing IPod!

Hoping someone can help me with my new Ipod Nano. I installed the IPod Updater and Itunes programs from the provided CD and formatted the Ipod. That all works fine -- the Ipod actually works, etc.
But during the actuall instation process, the Hardware Update Window came up for the 'Apple IPod USB Device' (I use Windows XP) I've tried to have it install automaticaly and manualy, without any luck. As a result, when the IPod is connected to the computer, I get a '!' on the device in Windows Explorer and neither ITunes or the Ipod Updater -- or Windows -- will reconize it!
If I connect my Ipod to the computer, the 'hardware' icon comes up in my system tray and the Ipod screen changes to the 'Do not disconnect' message. I can click on the hardware icon to 'remove' it. But I can't DO anything with the Ipod if nothing will reconize it!
I've tried updating the ITunes and Updater to the latest versions, plugged the USB cable into different spots on my computer, uninstalled and reinstalled everything, this time selecting the 'do not connect the Ipod to the computer at this time' option.....nothing. Windows just will NOT reconize the IPod and everytime I install the software I get that Hardware Update Window screen up!
Is there a driver for this I'm missing somewhere? What's going on? I can't do anything with my IPod and can't even find a phone number to call Apple for help!

1-800-275-2273.
This might be an issue with your operating system. You might also want to try using it on another computer before calling them as they'll probably ask you to do so. This will isolate the problem to your computer and they might tell you to try calling Windows or getting the latest drivers for your computer.

Ipad4 connection MTP USB device error with Windows 7 64 bit

I have recently bought iPad 4. When I connected to my computer through USB running Windows 7 Professional 64 bit i got the following error message
"MTP USB Device failed to install"
Please guige me

Hello lwalbring and welcome to the Palm forums.
Your Visor, as you suspect, does not have Bluetooth, so you must use the IR HotSync option. Since you are using Windows 7 64-bit, I believe that you are going to have to upgrade to Palm Desktop 6.2.2 to make things work from an OS/Driver perspective.
Since you are using such an old device, you are also going to have to download and install the PalmHotSyncSetup Utility from Pimlico. This update turns on support for old Palm OS PDAs in Palm Desktop 6.2.2. Without the update, you won't be able to sync your Visor with Palm Desktop 6.2.2. The software is free and the link is all the way at the bottom of the screen.
Lastly, if your PC doesn't have an IR port on it, you will need to purchase a USB to IR adapter. Some laptops still have IR ports and most desktops don't.
Once you have all the pieces, you'll want to go back to the Windows 7 and Vista HotSync thread again, and follow the directions for setting up and configuring IR HotSyncs.
Alan G

HT201401 MTP USB Device not installed

Hello -
I'm new to this community message board.
I recently started having this problem about two months ago. Up til that time I didn't have this problem.
When I would connect my iPhone 4S to my windows 7 computer, the folder files would pop up and ask if I wanted to open the files from the iPhone connection through the USB port that I have always used.
It started two months ago, that when I connected my iPhone in the same way that I have always connected through the USB port, that instead Windows would recognize the connection but attempt to install the drivers. A message always comes up saying that Windows can not install the MTP USB Device because It can not load the drivers for this device and Code 31.
I've searched the web for solutions but have not found any that fix this problem. These are troubleshooting things that I have tried:
I have downloaded and installed the lastest iTunes application.
I have upgraded the iPhone to the lastest IOS
I have reset the iPhone, then reconnected to USB port on computer
I have connected the iPhone to another USB port on my computer
I have selected an earlier Windows System Restore point at a time before this problem existed and restored my computer
I have used the Windows 7 installation disk to repair the Windows Operating System
I have uninstalled the drivers for the iPhone in Device Manager, restarted the computer and then connected the iPhone and USB cable to the computer.
I have used another USB Cable to connect the iPhone to the computer.
I have looked in Control Panel under Devices - the Apple Mobil Device Driver is displayed with no problems. However the iPhone is displayed with a triangle and an exclamation mark in the triangle.
I have viewed Device Manager in Windows 7 and looked in these categories: Universeral Serial Bus Controller - everything is okay, no triangles with exlamation marks in them or any other markings on any of the Standard Enhanced PCI to USB Controllers. The Category in Device Manager called Human Interface Devices also looks okay.
In Device Manager the category Portable Devices lists H:\, MTP USB Device, WPD File System Device Driver all have the small yellow triangle with the exclamation mark in the triangle. When I double click to open these devices up in Device Manager they all say the device is not working properly because windows can not load the drivers required for this device. (Code 31).
Windows 7 still does not recognize the iPhone as it use to do with the open file window that pops-up when the iPhone is connected to computer. Windows shows these drivers for the iPhone on my computer and these show up in the properties of the MTP USB Device - which is what Windows 7 calls the iPhone connection.
UMDF\WpdMtpdDr.dll
winusb.sys
WUDFRd.sys
WpdMtp.dll
WpdMtpUS.dll
So has anyone had this problem of Windows giving error message “can not load drivers for this device and Code 31” and is there a fix?
Thank you if you can help with this problem.

I had the same iss - it's a known issue whereby Windows attempts to use the wrong driver to access the phone.
BACK UP YOUR REGISTRY!!! Editing the registry can be (read: IS) dangerous and can cause no end of pain if done incorrectly.(But dont wort..i did it...)
- To Back Up your Registry: Click Start menu and click "Run". Type "regedit". Click File, then choose export and type "iphone driver fix registry backup".
- Click Export and let it export the the registry to a file.
- To fix the issue: Follow the folder tree on the left to: hkeylocalmachine > system > current control set > control > class
- Find “{EEC5AD98-8080-425F-922A-DABF3DE3F69A}” down the LEFT hand side and click on it.
- Under the list on the RIGHT hand side find "UpperFilters"
- Right-Click UpperFilters and click delete
- Close the registry editor and restart your PC (without the iphone attached).
- Once restarted and logged back in, plug in your iphone and voila! Windows will actually choose the correct driver and you'll be in like flynn.

When I plug in my iPhone to a USB port on the back of my computer I get the error "MTP USB Device driver was not successfully installed" and of course there is no device that shows up either. It would be great to download my photos! I'm using Windows

When I plug in my iPhone to a USB port on the back of my computer I get the error "MTP USB Device driver was not successfully installed" and of course there is no device that shows up either. It would be great to download my photos! I'm using Windows

Go through this support doc:
OS: Device not recognised in iTunes
Windows: http://support.apple.com/kb/TS1538

The latest version of iTunes did not install properly on my Windows 7 PC. I am getting the following error message: "Service 'Apple Mobile Device' failed to start. Verify that you have sufficient privileges to start system services." Can anyone help?

The latest version of iTunes did not install properly on my Windows 7-64bit PC. I am getting the following error message: "Service 'Apple Mobile Device' failed to start. Verify that you have sufficient privileges to start system services."
I have tried the following troubleshooting steps without success:
Restart PC
Uninstall iTunes and attempt to reinstall
Verify that I am signed in as an administrator
Download and save iTunes64Setup file, right-click, and run as Administrator
Disable Norton antivirus software
Any suggestions would be greatly appreciated!

Hi Iss9243,
Welcome to the Support Communities!
You've already tried some great troubleshooting steps, but the article below gives you quite a few more for this issue. Hope it helps ....
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Cheers,
- Judy

A connection to the deployment share could not be made - Networking device did not have a driver installed

I have a couple of HP 8200 desktops that I think might have bad nics. When I PXE boot them and start my LiteTouch, I get a Wizard error that says
A connection to the deployment share (\\mydpshare\share) could not be made. The following networking device did not have a driver installed
PCI\VEN_8086&DEV_1502&SUBSYS_1496103C&REV_04
I have that driver in MDT and it works on other HP 8200s. Looking into the Wpeinit.log, it looks like the driver loads but maybe the nic is bad:
Installing device root\kdnic X:\WINDOWS\INF\kdnic.inf succeeded
Installing device pci\ven_8086&dev_1502 X:\WINDOWS\INF\net1ic64.inf succeeded
Spent 16903ms installing network drivers
QueryAdapterStatus: no adapters found
Spent 0ms confirming network initialization; status 0x80004005
WaitForNetworkToInitialize failed; ignoring error
Has anyone seen this before?
Orange County District Attorney

Hi,
According to your description, it should be Intel NIC driver problem. I have checked HP official website, there is new NIC driver released, please access to the link below to download the NIC driver for test:
http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5037932&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D2%257CswItem%253Dvc_111651_1%257CswEnvOID%253D4060%257CitemLocale%253D%257CswLang%253D%257Cmode%253D4%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken
Roger Lu
TechNet Community Support

Pod Touch 32GB MTP USB device has failed to install and can't sync.

After updating iTunes on my Win7 64bit PC, when I plug my iPod Touch 32GB in, I get the error message "MTP USB device has failed to install" and can't sync. Yesterday, everything worked well.
Need help, please!

Thank you. I removed iTunes, QT, Safari and related software, then applied a Windows update and reinstalled iTunes and related software. It solved my problem and let me sync my iPod.
Thanks!

MTP USB Device not recognized under Windows 7 Ultimate

Hey everybody, I'm sure there are plenty of similar threads about this issue, however I haven't seen any with Windows 7 as OS.
My problem is in the recognition of the driver, since the MTP device is not working properly. I've tried alot of possible solutions, but none of them have worked, i.e the removal of the driver in device manager, tried a custom script for the inf file, deleting of all USB/portable related drivers.
Its sad that no recovery tools are yet compatible with Windows 7, atleast not that I'm aware of.
Please, throw some more suggestions/ideas! My Zen works perfectly fine under XP btw.

I was having the same problem with my Zen Vision:M under Win7 Ultimate 64-bit.
No matter what I tried from deleting the usb root hubs and reinstalling drivers, nothing would get the mtp usb device driver to load.
I found that the mtp usb device driver will load correctly as long as you are plugging the USB cable into a direct port and not running it through a USB hub. At first I thought it might be due to an incorrect USB voltage, but the hub I'm using is a powered Belkin hub. Very strange!
So give that a shot -- run the USB straight to a port out the back of your computer. Don't use a USB hub or ports off your monitor since that is actually a hub as well.
Good luck!http://forums.mycreativefansite.com/...ify_inline.gif

Apparently a recent update did not install correctly and we get a message: Service (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system services. How do we fix?

Apparently a recent update did not install correctly and we get a message: Service (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start systen services, How do we fix this?

Solving the iTunes Installation Problems in Windows
1. Apple has posted their solution here: iTunes 11.1.4 for Windows- Unable to install or open - MSVCR80 issue.
2. If the Apple article does not fully resolve the problem for you, then try Troubleshooting issues with iTunes for Windows updates - MSVCR80.

Network device did not have a driver installed pci\ven_10ec&dev_8168&subsys 1992103C&REV_0C

Hi: The only suggestion I can offer would be to try the driver directly from Realtek. Second driver on the list. http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=13&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false

Hello All, I have installed WDS/MDT2010 to deploying the Windows & operating system, it works with for most of my HP laptops models. When I deploy in ProBook 645 G1 it gives me foloowing error. A connection to the Deployment share could not be made.
The following network device did not have a driver installed pci\ven_10ec&dev_8168&subsys 1992103C&REV_0C
Retry : Try again to connect to the deployment share or give up. I have download all the network driver available for this model and imported them in out of box driver,update the deployment share and run again but still having the same issue. Appreciate if any one can help me on this. Thanks

Windows 7 is reporting that apple mobile device usb driver is not installed correctly using iphone 4

Problem when syncing iphone 4 under window 7 error message suggest that uSB driver is not installed correctly Error 52. Any ideas!

I had similar problems and found a useful site. My iPhone 4s and iPad weren't found by iTunes. Tried the suggestions below and my problem was fixed.
http://randomwindowstips.wordpress.com/2009/12/08/windows-7-itunes-9-software-is -not-installed/
Hope this helps!

Windows 7 64bit has an MTP USB Device Failed error message when I attach my Ipad1

I keep getting an MTP USB Device Failed error message when I plug in my USB cable into my Ipad1. Can someone help?

This is NOT resolved. The "Upper..."Key in the registry editor doesn't exist as you can see below in the image I am providing. This is still an OUTSTANDING issue, can someone please help with resolving this issue, super frustrating.
This is not just an iPAD issue, I get the same problem with my iPhone as well, both (iPhone and iPad) have the latest iOS 6.1.3 installed as well.

My 10.8.3 update did not install properly citing an 'Unknown Error'. Now, my Mail and Mac App Store aren't working. What went wrong and how do i fix it ?

My 10.8.3 update did not install properly citing an 'Unknown Error'. Now, my Mail and Mac App Store aren't working. What went wrong and how do i fix it ?

I tried this and still have the same problems. If I open Address book or the Mac App Store I get the library rebuild popup and a hang. I created a fresh user and then things are better apart from the printing issue. Its clearly some 3rd party software issue but the crash logs are meningless to me. I used the excellent Etre check app from http://www.etresoft.com/etrecheck so I have a list of what is being loaded and can compare clean and crashed user info but as I cant work out which of the startup items, launch agents, launch daemons etc that are causing the problem.
I have eliminated Dropbox, Mac Keeper and Witness, and it isnt related to my exterrnal LED cinema dispay or my external thunderbolt drives, or any USB devices if thats any help to anyone else. Info from Etrecheck follows -
Kernel Extensions:
          com.oxsemi.driver.OxsemiDeviceType00          Version: 1.28.7
          com.rogueamoeba.InstantOn          Version: 6.0.2
          com.rogueamoeba.InstantOnCore          Version: 6.0.2
          com.Cycling74.driver.Soundflower          Version: 1.5.3
Problem System Launch Daemons:
Problem System Launch Agents:
Launch Daemons:
             [not loaded] com.adobe.fpsaud.plist
             [not loaded] com.adobe.SwitchBoard.plist
             [not loaded] com.bombich.ccc.plist
             [not loaded] com.dymo.pnpd.plist
             [not loaded] com.intego.BackupManagerPro.daemon.plist
             [not loaded] com.micromat.TechToolProDaemon.plist
             [not loaded] com.microsoft.office.licensing.helper.plist
             [not loaded] com.orbicule.witnessd.plist
             [not loaded] com.sierrawireless.SwitchTool.plist
             [not loaded] com.stclairsoft.AppTamerAgent.plist
             [not loaded] org.macosforge.xquartz.privileged_startx.plist
             [not loaded]          pcloudd.plist
Launch Agents:
                 [loaded] com.divx.dms.agent.plist
                 [loaded] com.divx.update.agent.plist
                 [loaded] com.epson.epw.agent.plist
                 [loaded] com.lacie.raidmonitor.daemon.plist
                 [loaded] com.lacie.safemanager.daemon.plist
                 [loaded] com.micromat.TechToolProAgent.plist
                 [loaded] com.orbicule.WitnessUserAgent.plist
                 [loaded] org.macosforge.xquartz.startx.plist
User Launch Agents:
             [not loaded]          .DS_Store
                 [loaded] com.adobe.AAM.Updater-1.0.plist
                 [loaded] com.adobe.ARM.202f4087f2bbde52e3ac2df389f53a4f123223c9cc56a8fd83a6f7ae.plist
                 [loaded] com.digitalrebellion.SoftwareUpdateAutoCheck.plist
                 [loaded] com.divx.agent.postinstall.plist
                 [loaded] com.google.keystone.agent.plist
                 [loaded] com.propaganda.dejavu.dvmonitor.plist
                 [loaded] com.valvesoftware.steamclean.plist
                 [loaded] com.zeobit.MacKeeper.Helper.plist
User Login Items:
          iTunesHelper
          Synergy
          TomTomHOMERunner
          Dropbox
3rd Party Preference Panes:
          Déjà Vu
          Flash Player
          Flip4Mac WMV
          GR-55
          Paragon NTFS for Mac ® OS X
          Perian
          Printopia
          TechTool Protection
          Witness

MTP USB Device did not install

Similar Messages

Maybe you are looking for