Multi Cam doesn't work properly?

I can't find where is Premiere CC how to open the multicam window, and now audio won't play back and it's laggy as all hell

ugh
i have sound now, but video won't playback. If I copy and paste it into another new sequence it seems to be there but it laggy as hell.

Similar Messages

  • Multi-cam doesn't work when I resync

    Hello,
    I have an hour and a half 3 angled multi-clip to edit. I did not have a TC generator, so what I did was give Aux TC, which has worked perfectly in shorter projects.
    In this project, I gave Aux TC that start with 2 or 3, so as to avoid "negative" TC problems. Seeing as I have 6 clips, I entered each one as a seperate angle. I'll explain a little more: I had 3 cameras, 6 tapes, and some of the tapes overlap a quite a bit. (example: angle 1 continues 15 minutes after angle 3 is replaced by angle 4)
    However, when I created the multi-clip, it wasn't perfectly in sync, even though the Aux TC were all given based on a pre-layout I had done in a sequence, and I gave the Aux TC based on the first image. Some of the clips were subclips.
    I tryed resynching in the viewer, and pretty much succeeded, with the acception of one piece that was 2 frames behind. I would resync it, try to edit, and I would get a message saying that the content wasn't sufficiant to perform that edit. (Rough translation from French, because my Final Cut is in French.) It gets stuck, and I can't edit.
    So I decided to live with the 2 frame difference (because I had spent 2 days trying to solve these sync problems), after all that angle was so wide, that mouth details were invisible. However, after reaching the point where one of the angles has no more footage but a new angle kicks in with the rest of the footage, suddenly I get the same problem again. I suppose that footage that was resynched later had the same problem as the angle with a 2 frame difference. I guess I hadn't noticed it before I started editing. It won't edit, "not enough content", and won't switch when I click in the different angles. Instead it gets stuck for a few minutes.
    I can't figure out the source of my problems: the subclips where the aux TC is getting mixed up? Resynching that isn't ment to work?
    Keep in mind that I have already succesfully edited 1 hour mult-clips using auxiliry TC.
    Any ideas?

    Thanks, Michael, I work the way you do, only a then assign time codes. But I'll know in the future to use your method as soon as I have the slightest problem.
    And thanks too, Lydilove, unfortunately I had had the time to re-edit half an hour's worth, find out that it still wasn't in sync, and then re-edit again before I read your advice.
    I'd still like to understand what isn't working.
    Currently, I have edited an hour's worth and have half an hour to go, and suddenly, out of no where, one of the angles doesn't want to work. All I hear is an "error" sound, and no explination.
    So I'm going to start putting Lydilove's method in place, but why do I have this problem?
    (PS: the angle just "started" having footage in it, that's where it stopped working. Before, on the time line, everything worked.)

  • Droid 3 problems - Cell standby eats up a ton of battery - camera doesn't work - more in thread.

    I am making a post regarding this problem because it seems only new posts get a response from VZW reps. Before you ask, yes I have used the battery saving tips - this is clearly a problem with cell standby and wifi. They are, by far, the biggest consumers of the battery. I don't know what's going on here but this should not be happening. Even on the unpatched Thunderbolt the battery life wasn't this bad. This battery problem is clearly not because of any third party apps, even with no accounts set up and nothing installed, the battery drains very quickly.
    The camera doesn't work right, and regularly freezes. When it does work, it's very blue. I am told this is a known issue and the patch is on the way I'm told.
    The stock keyboard's suggestion bar often stays on the screen no matter what, regardless of whether I am typing or not.
    The Droid 3 does NOT charge off my car's USB cable, every other phone and mobile device I've tried does, however, so this is clearly an issue with the phone.
    The stock homescreen lags and redraws often.
    The pre-installed apps that I don't want or use, are using up a big chunk of memory (and certainly not helping already abysmal battery life). If they are killed, they just start themselves again. They cannot be uninstalled. If Verizon wants to give us extra apps, great, but allow us to uninstall them.
    I received this as a replacement phone because the previous replacement phone was having issues. I've gotten dozens of replacement phones and ALL of them have had problems. Whatever steps are being taken to ensure these phones work properly do not ensure that people are getting a working phone. This process needs to be revised. The premium price we as Verizon customers pay should translate to our customer experience.
    -A very frustrated customer.

    I've had a Droid 3 for about a month. I think it's a really good phone, but cell standby and phone idle are the biggest consumers of battery life on my phone. The camera is slow to load and the images have a blue tint sometimes. When surfing the web or the app store and exiting afterwards, the main screen can take 8 - 16 seconds to materialize. When surfing through the Social Messaging (NonBlur) widget, it repeats things you've already read when you check it later on and when replying to comments via the Social Messaging widget, they don't always post. The back cover squeaks now from removing it occasionally to pull the battery when the phone freezes up. For being a 1G dual core processor phone, you would never know it. I've also had problems with the suggestion bar remaining on the screen even after you press the space bar. The app store is maddeningly slow to load. The indicator next to my battery charging port doesn't work, well it flickered once. I haven't had issues with Bluetooth or wifi as some have. My GPS seems to work well. 
    The bloatware on the phone is ridiculous. I don't use any of the Verizon apps or other preloaded apps. They take up a lot of the useable space on the phone and can't be removed. I really don't care about an NFL app....and I can't remove it or anything else. Verizon should give you the option of removing the apps you won't use. It would be a good customer service move. Instead, I think its selfish to make us live with apps that take up space and slow the phone down. This phone comes with Android 2.3.4 which is the fastest version of Android right now....I can honestly say that my Droid X with 2.2 was faster on the move than this phone. However, after downloading 2.3.3, it ruined the phone and a replacement.
    I think if a software update addresses most of these issues, the Droid 3 would be outstanding. The hardware keyboard is the best on the market and I love the 4 inch screen. I pay $100 + a month for service through Verizon. I think the phone should operate as promised. The 8 megapixel camera is slow to load and focus. My old Droid X had a good 8MP camera sensor. Lesser phones have great cameras. My boss' iphone 4 takes WAY better pics with a 5MP camera. I know it's a software issue and that it can be resolved. Make this phone world class by working with Motorola to deliver a quality software update. 
    I stick with Verizon because of their reliable coverage. If this phone doesn't get addressed with a software update, I'll look at a WP7 phone or something on Sprint (better prices on data etc) or Virgin Mobile which has some decent phones and dirt cheap messaging and data plans.

  • Preview ok,but doesn't work properly when build dvd

    everything is ok when preview but when i built to dvd folder,media player classic only could play separate dvd file,and no main menu. then i try windows media player, the main menu came out but none of the buttons work.
    Any ideas? Thanks a lot

    sorry about the multiple posts. mines is encore DVD 2.0 trial on windows XP. I've checked the help and FAQ but none of them related to my situation. I've got 1 sub menu with 1 main menu. no problem when preview but when i built a dvd folder it doesn't work properly. media player classic couldn't play the main menu, sub menu work but not the buttons on it. windows media player can play the main menu but none of the buttons work either!! I've been working on it for a whole day. course work deadline is this Thu, so please give me some advice. Many thanks.

  • Dreamweaver 8  doesn t work properly on imac intel "17"

    Hello guys need some help, I m new to mac and I´ve installed dreamweaver 8 but it doesn t work properly. Instead of the insert toolbar I get boxes with a '?' plus in some occasion when I want to save a work instead of the usual " save or ok or discard" the button appears as " undefined". Can anyone help please?
    Here is a picture of the error I get. Regards
    http://flickr.com/photos/37586542@N00/
    imac 17 intel duo   Mac OS X (10.4.6)  

    It would appear to me when you installed Dreamweaver,
    some image files got misplaced or lost by mistake.
    Did you ever go and search for images and start
    erasing images you didn't know what they came from?
    If you did, then those may be the image. Those
    images are little modular pieces that Dreamweaver
    uses to display information on the screen.
    I would install Dreamweaver from scratch and make
    sure it is in the Applications folder.
    Hi, did everything posible, I even downloaded a evaluation version, just in case but it seems it s only me who has this problem, I problaby need to download somekind of firmware or java but don t know which. Cheers

  • My palm m105's touch screen doesn't work properly after a sync.

    I dug out my old m105, put new batteries in and start it. On first launch it auto runs the alignment tool, and after touching all the points it goes to the main screen and works fine. No problem till here.
    Now, I plug it into my old computer which still has the palm software with my apps, and I run the sync operation (from the palm device sync manager, cause I lost my cradle and I'm connected via the serial cable), and it syncs fine BUT, here comes the problem, when it finishes the sync (successfully) the touch screen is all misaligned. I can't go back to the home screen or do anything useful.
    My palm m105's touch screen doesn't work properly after a sync.
    I dug out my old m105, put new batteries in and start it. On first launch it auto runs the alignment tool, and after touching all the points it goes to the main screen and works fine. No problem till here.
    Now, I plug it into my old computer which still has the palm software with my apps, and I run the sync operation (from the palm device sync manager, cause I lost my cradle and I'm connected via the serial cable), and it syncs fine BUT, here comes the problem, when it finishes the sync (successfully) the touch screen is all misaligned. I can't go back to the home screen or do anything useful.
    Thanks in advance!
    Post relates to: Palm m105
    Post relates to: Palm m105

        Maldoman578,
    Let's help solve this mystery together! Is your screen freezing after every reboot? Is there any physical/liquid damage on the device? When did this issue begin? Did you notice this after a recent update or application download?
    EfrainM_VZW
    Follow us on Twitter @VZWSupport

  • Canon mini Disk camera doesn't work if external drive connected

    A long story.      Anyway, I have a MacPro Intel Dual Core 266 Ghz with 5 Gbs RAM,  4 internal hard drives HD1~HD4 (HD1 OSX 250 and three 500Gb) and two external HD5 (two partitions~HD5 & Time Machine Backups) and HD6 (1 Tb each).
    I've been using a Canon mini DV video camera FV-M10 (Firewire 400) for live video (Skype/iChat) and also for importing video into Final Cut Express, After Effects or iMovie up until a few days ago.  Both "live" video and from the recorded mini cassette tape.  Then all of a sudden not one of the software recognized my camera anymore.  I tried both Firewire 800/400 and USB2 connections using a few different cables. In Skype...(sometimes) it automatically shows the name FV-M10 in the camera slot, but the screen is black.  No, I checked if I left the cover on.  I checked my Sony WX-5 digital camera and see if that is recognized.  Yes, both pics and AVCHD videos are seen using the USB connection. 
    The problem started like this.
    I was downloading a file.  Had to work for an hour and when I came back upstairs.  I noticed that the screen was frozen.   So, I shut the Mac down.  And when I started it again, well nothing happened except for a grey screen.  A half~sized cursor was stuck up in the top left.  But, my mouse also had a cursor which was movable.  
    It wouldn't even recognize the OSX Install Disk holding down "C" or "Option".  Only starting with "Shift" held down, "Safe Boot"  could I use the basics like Mail, Safari, Firefox.   NO sound and no video. Tried a few times as well as cleaned my OSX HD1 hard drive and re-installed from "Safe Boot" mode".   So, I had it sent into Apple Tokyo for repairs.   Apple put in a new board.     Great!      I came it back in two days.   I cleaned the OSX hard drive and re-installed Mac OSX with the up-dates as well and got some of my main backed up stuff Mail, bookmarks, address book etc.   It started fine.     But, when I went to use Skype, iChat, iMovie or Final Cut Express  they still couldn't recognize my camera.  I had been using the Canon FV M10 camera for a few years with both external hard drives on.  There were never any problems until just before I sent it into the shop.
    There was only one way to use my camera.  Un-Plug the external HD6.  Then the camera functions fine.  but remember I had been using this camera with both HD's for around two years without any problems.
    Notes on symptoms:  and what actions I took.  
    Front connections: FW400 Canon camera.  FW800 (Tried connecting HD6)  
    Rear Connections: USB2 1) MidiMan 2 x2   2) mouse  3) Canon Printer
                                   FW400 HD5  FW800 (tried HD6)
    With HD6 Connected.
    iMovie 11 9.02 : Start iMovie  O.K.  No camera on.   Turned camera "on" then "No Camera Connected" notice came up.   (did this a few times)   Turned camera off.   Quit iMovie. 
    2nd start:  Camera On.   iMovie freezes.   Spinning Colored beach ball.   I then Force Quit Option-Apple-ESC
    iMovie shows (not responding)  When I turn off the camera.  (not responding) disappears and iMovie is working again.  But, "No Camera Connected" shows again.  Quit!
    Un-Plugged (Ejected) HD6.
    When I un-plugged HD6,    (tried both the front and rear connections).   iMovie still on.  
    "No Camera Connected"  I Quit iMovie.
    Re-start iMovie:  Camera on… Live video and record miniDV tape can both be seen. 
    Skype:  Both live video and mini DV tape recording even plays back over Skype screen.
    iChat (same as Skype) O.K.
    Since Apple replaced the board 661-3932 Card Video, NVIDIA GeForce 7300 GT which cost just about $X00.00  (¥XX,000).   I assume that they don't also check all the connections etc. I mean from the connector to the video board.
    The call to Apple Tokyo today.  
    Just talked to Apple (Mac) Tokyo about my computer problem.  Seems like they're trying to squeeze their way of more repairs by saying I have a hard drive configuration problem.   But it doesn't seem like that!   I worked with it 2~3 hours today...and  here is the basic problem.
    I've used the Canon FV M10 mini DV camera with Skype, iChat, iMovie and FCEx for few  years  (HD6) is over a year old-the most recent add on) with no problem.    With both external 1Tb hard drives.  And Apple said that it's a 3-party problem.  (different makers etc.)  But, it's NOT!     Yes, they put in a new board.   But, I'd say the problem is from the connection (where I plug the cable into the Mac)  to the board. 
    When I connect HD6 (1Tb ext hard drive).   FW 800 (either back or front connection) the video camera doesn't work in  Skype, iChat, iMovie, or Final Cut Express.     If I eject and Un-Plug HD6  all of them work fine.  The camera "live" or the camera playing back the mini DV tape video.
    Wouldn't this be a problem between the connections (front & back) to the new video board?  Or does anyone have an answer.   Apple seems to have said, "We can't help you".   Please someone help!  thanks

    +My mini isn't responding to startup commands like "C" or "D" from the keyboard.+
    You'll need a wired usb keyboard for these commands to work -- and the Apple Aluminum keyboard won't work either.
    But just about any PC usb keyboard will work. Alt maps to Option and Win-key to CMD.

  • Help, web cam is not working properly with win vista

    Hii.. my web cam is not working properly with win vista..even if the icon appears bt it does nt start.. its
    lenovo easy capture 2.5...so if u cud suggest me anything...
    Moderator note; subject edited

    re-install drivers and try again. ( also easy capture )

  • My HP-Pavilion dv6 web cam is not working properly, fluctuating always

    My HP-Pavilion dv6 web cam is not working properly, it is fluctuating always

    re-install drivers and try again. ( also easy capture )

  • My Safari doesn't work properly after installing Lion.  Don't like it, how can I uninstall? (Cloud not worth it)?

    I upgraded ti Lion 10.7.2 for icloud but it's causing other problems with my mac.  My Safari doesn't work properly anymore.  Wishing I didn't upgrade, anyone know how to fix this or do i just have to uninstall?  Thanks,

    Wipe the drive clean and install Snow Leopard from your install disk.
    Might be less work fixing Safari. Try Resetting Safari.

  • I have an iphone 3GS and I have upgraded it to iOS 6. Since then it doesn't work properly. Every now and then it has been restarting by itself and requiring restore. When I connect it to itunes it restarts again and again. Is there any solution?

    I have an iphone 3GS and I have upgraded it to iOS 6. Since then it doesn't work properly.
    Every now and then it has been restarting by itself and requiring restore. When I connect it to itunes it restarts again and again without letting me take any action. Is there any solution?

    Hey, There are afew things you can try.
    - Simply turn your phone off and back on again
    - Hold down your home button and your lock button and let goes as soon as the screen goes black (Phone will power down) - Then turn on your phone and hey presto!
    - Back up your iPhone to your PC, then restore it..
    this ones last cause I think you may have tried it already..
    - Close all open applications
    Hope this helps!
       Kieran.

  • HT1923 The sync function on my iPod Touch 3rd generation doesn't work properly.  My OS is up to date, but some of my podcasts won't transfer onto the iPod, and it won't delete ones I've already listened to.

    The sync function on my 3rd gen iPod Touch doesn't work properly.  It won't sync all the podcasts I've downloaded, and it won't delete ones I've listened to and deleted on iTunes.

    Close your iTunes,
    Go to command Prompt -
    (Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
    (Win XP SP2 & above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
    In the "Command Prompt" screen, type in
    netsh winsock reset
    Hit "ENTER" key
    Restart your computer.
    If you do get a prompt after restart windows to remap LSP, just click NO.
    Now launch your iTunes and see if it is working now.
    If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
    iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
    http://support.apple.com/kb/TS4123?viewlocale=en_US

  • What can I do if my CD or DVD drive doesn't work properly in Windows 8?

    QuestionWhat can I do when if my laptop CD or DVD drive doesn't work properly in Windows 8?
    AnswerNote: For help with this issue in Windows 7, please see this article.
    To get your CD or DVD drive working correctly, try these suggestions in the order listed.
    Reinstall the Driver
    Hold the Windows key and press the 'x' key to open a menu in the lower-left. In this menu, select "Device Manager." Expand "DVD/CD-ROM drives." Right-click the entry for the CD/DVD drive nested under "DVD/CD-ROM drives," then select "Uninstall." Finally, restart the computer. The computer will reinstall the drivers for the drive.
    Power Cycle
    Even when your laptop is off and unplugged, residual power can still be held in some components. While this is normal, clearing it can help with some hardware problems. Perform these steps to complete what’s called a power cycle.
    Ensure the laptop is turned off.
    Unplug the laptop's AC power cable.
    Unplug all wires and peripherals. This includes CDs, DVDs, USB sticks, mice, printers, and any other accessories.
    Remove the battery (if the model has a removable battery). If the model does not have a removable battery, check your user's guide to determine if you have a pinhole reset on the bottom. If you do, press this.
    Hold down the power button for thirty seconds.
    Reattach the battery if removed.
    Connect the AC adaptor to the power socket that was confirmed to be working in the first step.
    Connect the other end of the AC adaptor to your computer.
    Start the computer and test the drive
    Microsoft Fix-it
    Your computer may exhibit one or more of the following symptoms:
    Your CD or DVD drive no longer appears in Windows
    Your CD or DVD drive does not read or write and is shown as disabled
    The media in your CD or DVD drive cannot be read
    The media cannot be written to a CD or DVD inserted into the drive
    You receive an error message about your CD or DVD drive
    If any of these symptoms apply to your computer, use Microsoft Fix-it troubleshooter available here.
    System Restore
    Try using System Restore to restore to the most restore point from before the problem arose.
    How To: Understanding System Restore, Refresh, Reset, and, Recovery options in Windows 8 + Video
    System Recovery
    If the System Restore doesn't solve the issue, you could try a System Reset. Resetting your laptop to its original, out-of-the-box state is a great way to eliminate software as a possible cause of the problem. Note that doing a system reset will return the laptop to its default conditions, completely wiping your data. Information on how to perform a system recovery can be found in your user's guide.
    For more information on performing a recovery, see the following article:
    How To: Understanding System Restore, Refresh, Reset, and, Recovery options in Windows 8 + Video
    Contact Customer Support
    If the drive doesn't work after performing a recovery, it may be due to hardware failure. Please call customer support or seek servicing.

    See this Microsoft article - http://support.microsoft.com/kb/314060/en-us  For ways to fix manually
    and/or use the proper microsoft fixit 8.1 and 8 or the other one for Windows 7, Vista, and XP listed below.
    (these are from the Microsoft article)
    Resolution 2: Use the CD/DVD Fix it troubleshooter
    To automatically fix common issues with CD or DVD drives, click Run now, and then follow the on-screen instructions. Windows 8.1 and Windows 8   
    The Automatically diagnose and fix common problems with CD or DVD drives troubleshooter may automatically fix the problem described in this article.
                                    This troubleshooter fixes many problems. learn more
    Run now
    Windows 7, Windows Vista and Windows XP
    The Automatically diagnose and fix common problems with CD or DVD drives troubleshooter may automatically fix the problem described in this article.
                                    This troubleshooter fixes many problems. learn more
    Run now
    If your problem is not solved, try the next
    S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

  • Satellite Pro L20 doesn't work properly with USB Fast Track audio i.f.

    Hello!
    I have used my Fast Track USB on new Toshiba Satellite L40 and I never had problems with it. I could set low latency and I did few songs with it.
    Yesterday I bought another notebook, thinking of home recording studio. It's used Toshiba Satellite Pro L20. It doesn't work properly with my interface. When I listen music on Winamp or do anything on Fruity Loops I hear loud clicks, pops, noises. They introduce samples, or they appear during playback or after a sample is stopped.
    I noticed, drivers for Satellite Pro L20 are a problem. Its not supported by Toshiba anymore?! The only drivers for chipset are very old and you can download em only from Toshiba website. The chipset is ATI Xpress 200M. Its drivers are with graphic card. Recently I noticed you can download "ATI Catalyst Legacy Display Driver for Windows XP - Motherboard/IGP Drivers 9.11" and CRACK IT to make it possible to install on mobile unit such as L20. Yep its funny but its impossible to do otherwise!
    things I have tried and they still not help:
    # drivers replacement, original were released in 2004. I installed recent version.
    # driver settings, low latency, high latency
    # asio and different settings
    # pluging the interface to another usb socket.
    # trying what happens when I use battery and when I use adapter
    # updated bios
    # turned off onboard units such as wifi card, sound card
    # checked IRQ list
    pops still appear.
    my config:
    Toshiba Satellite Pro L20
    Win XP Home SP3
    Celeron M 1,5GHz
    896Mb ram
    M-Audio Fast Track USB, drivers: 6.0.2
    Kind regards

    Thanks for answer. I still have L40 but I try to run my homerecording on L20. The L40 is now used by whole my family. It's possible to swap them but there's a problem - L20 has Norway keyboard and I'm the only person at home who doesn't often look down while typing. In Poland, we use standard ms keyboard. I'd buy special stickers, it's about only to make special chars get back to their places.
    I installed Windows on this computer end set it to best performance possible.
    Since I created this thread, guys from M-Audio support tried to solve my problem - nothing helped. I think potential solutions are exhausted.
    Message was edited by: lidia.pochron

  • Hp laserjet P1006 doesn't work properly

    my Hp laserjet P1006 doesn't work properly on my windows 7(64-bit) and whenever I try to print a page the orange light just flashes and then the green light flashes and then it doesn't print at all.I've tryed everyway including reinstalling the software or even turning it off and then turning it on.Pleaseeeee.............help!!!!!!!!!!!

    Hello
    I understand you are no longer able to print with the P1006 on Win8.1.
    Did you uninstall the P1006 first?
    If not uninstall and reinstall the printer software again.
    Both drivers are the same if you look at the version on the website and should still work with the Win8.1.
    If you need more assistance just let me know.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

Maybe you are looking for