Multi-SSID Setup

Hello all. I"m trying to better understand multi-SSID and what better way to do that than to get my hands dirty! Unfortunately, I'm stuck and could use some assistance. I'm able to successfully connect to one SSID, the internal or corporate, but cannot get connected to guest SSID. I've attached my topology and Catalyst config, but here is what I've done thus far.
1. Created three new interfaces on the controller. One for management (10.52.x.x), one for guest (10.1.x.x) and the last for internal (10.65.x.x). All interfaces are using port 1 as the physical port and each have unique addresses (DHCP, Gateway etc) and vlan ID's assigned.
2. Next, I created two SSIDs (guest and internal) and assigned them to the matching interfaces I created in the previous step.
3. Configured and permitted all VLANs over the trunk links on the switch.
Please let me know if I've forgotten to add any pertinent information.

I've changed FA 0/8 to an access port in the native vlan. I do obtain an IP address when directly connecting my PC to the switch. I'm leaving my guest SSID as open authentication since this is just a test environment. After making these changes, I still cannot connect to the guest SSID. My internal SSID works flawlessly. I temporarily disabled DHCP requirement on the guest SSID and configured a static address on my laptop and was able connect with no issue. Seems the problem lies with DHCP..

Similar Messages

Multi ssid `s get no ip address

multi ssid `s get no ip address ip address two ssid get a third but I had to configure but received no ip address who can help me ?

I did that, that works for 2 ssid but when I want to make more get no ip address ?
dot11 ssid CISCO_2.4GHZ.Guest
   vlan 4
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   wpa-psk ascii 0 ***************
dot11 ssid CISCO_2.4GHZ.Private
   vlan 2
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   wpa-psk ascii 0 *************
dot11 ssid CISCO_2.4GHZ.Study
   vlan 3
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   wpa-psk ascii 0 Opleiding123
dot11 ssid CISCO_2.4GHZ.Testing
   vlan 5
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   wpa-psk ascii 0 *************
dot11 ssid CISCO_5GHZTesting
   vlan 7
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   wpa-psk ascii 0 *****************
crypto pki trustpoint TP-self-signed-1968951208
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1968951208
revocation-check none
rsakeypair TP-self-signed-1968951208
crypto pki certificate chain TP-self-signed-1968951208
certificate self-signed 01
3082023D 308201A6 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31393638 39353132 3038301E 170D3130 30373137 32333333
33385A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 39363839
35313230 3830819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100BA02 F9C8FD66 B6753332 39673712 3E8769A3 DA570286 F5325C16 23F214AB
8E177C69 B168B1D7 DFCB9441 AAE7BCEB C6F77C6C 03FD0C48 21C87C59 8F910C5C
9C12A862 C6A42C75 089D841E C661E383 D8F5CDF9 D707600A 248B5C52 04B073C3
DDD8E50B 1C550A57 F9B9A79A 9159DFB7 22815053 3CCEF64F 09B2616C 0DABB290
E64D0203 010001A3 65306330 0F060355 1D130101 FF040530 030101FF 30100603
551D1104 09300782 0552322E 6170301F 0603551D 23041830 16801463 74685C38
2688464C 3F32F91F 624012F6 A5DBA230 1D060355 1D0E0416 04146374 685C3826
88464C3F 32F91F62 4012F6A5 DBA2300D 06092A86 4886F70D 01010405 00038181
0018AC3A 41116193 F00C9669 F94ADCFF 012DF87E D813AC85 827DADE5 5A76681B
D6B0F166 DC262F3B 845DBE81 045EDB83 14A913E2 1913A385 049D6AF3 2675F6E2
2AB6D802 85A3D5C5 0849F7A0 80714F1C D5307A94 28186E82 1830BEAB DEEDD795
ED3E4145 5C420CBA 0E5866BE 58DEF1EE 13E376B7 F1240AC9 DAB9DACD 1210702C C2
quit
username Tim privilege 15 secret 5 $1$W7mt$xqYHnkhSkureCfhslNmKe1
username Cisco privilege 15 secret 5 $1$KKCD$7d1WzhdTz5iVyrjHJmZWE0
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 2 mode ciphers aes-ccm tkip
encryption vlan 3 mode ciphers aes-ccm tkip
encryption vlan 4 mode ciphers aes-ccm tkip
encryption vlan 5 mode ciphers aes-ccm tkip
encryption vlan 7 mode ciphers aes-ccm tkip
ssid CISCO_Guest
ssid CISCO_Private
ssid CISCO_Study
ssid CISCO_Testing
ssid CISCO_5GHZTesting
antenna gain 0
mbssid
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3.
m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel 2462
station-role root
no dot11 extension aironet
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface Dot11Radio0.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
bridge-group 3 spanning-disabled
interface Dot11Radio0.4
encapsulation dot1Q 4
no ip route-cache
bridge-group 4
bridge-group 4 subscriber-loop-control
bridge-group 4 block-unknown-source
no bridge-group 4 source-learning
no bridge-group 4 unicast-flooding
bridge-group 4 spanning-disabled
interface Dot11Radio0.5
encapsulation dot1Q 5
no ip route-cache
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio0.7
encapsulation dot1Q 7
no ip route-cache
bridge-group 7
bridge-group 7 subscriber-loop-control
bridge-group 7 block-unknown-source
no bridge-group 7 source-learning
no bridge-group 7 unicast-flooding
bridge-group 7 spanning-disabled
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface GigabitEthernet0.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
no bridge-group 3 source-learning
bridge-group 3 spanning-disabled
interface GigabitEthernet0.4
encapsulation dot1Q 4
no ip route-cache
bridge-group 4
no bridge-group 4 source-learning
bridge-group 4 spanning-disabled
interface GigabitEthernet0.5
encapsulation dot1Q 5
no ip route-cache
bridge-group 5
no bridge-group 5 source-learning
bridge-group 5 spanning-disabled
interface GigabitEthernet0.7
encapsulation dot1Q 7
no ip route-cache
bridge-group 7
no bridge-group 7 source-learning
bridge-group 7 spanning-disabled
interface BVI1
ip address 10.10.10.2 255.255.255.0
no ip route-cache

How to make Sales Person LOV org specific in case of Multi Org Setup

HI,
We are working on 11.5.10.2
We have a multi org setup and i am required to make the sales person LOV to populate only the org specific salespersons, at the sales order, quote, service contract levels.
Is it achiveable and if yes.....please letme know the way.
Reg,
Ajay Agarwal.

Hi
Try to play around with the security profile in the HRMS and attach it to the responsibility level
Regards
Ramesh Kumar S

Writing waveforms from Ch. 0 of niSCOPE to binary file in a multi-record setup?

Hello,
I am not very experienced with niSCOPE and writing waveform records, so I need some expert help here.
Here is my application:
I am generating a pulse train using a 6602 counter/timer. Each rising edge of this pulse train triggers an niFGEN to generate a single sawtooth waveform output to another device and, at the same time, acquiring data from Ch. 0 of an niSCOPE. I am fetching one record per rising edge of the pulse train for the niSCOPE (multi-record setup).
The attached VI is where I am at thus far. All triggering and reading/fetching of the waveforms seems to be working just fine when testing with an oscilloscope. I now need to save each waveform record along with the timestamp of its rising edge trigger to a binary file. The bottom of the VI is where my attempt is at saving the waveforms to a binary file, so the attention should be there when looking at it.
I am running LabVIEW from a computer connected to the NI PXI-Chassis using a cross-over cable.
Questions:
1.) Do I need to convert the data coming in on Ch. 0 of the niSCOPE to digital? Does it come in as analog from an oscilloscope? If I need to do this, how can I accomplish this?
2.) When I try to run an example VI to write a waveform to a binary file by choosing "My Computer" in the bottom left of the VI window, it works it saves the file just fine. When I change this to run on "PXI2", a file is not even created and I get an error on File Dialog (code# 7, I think) each time the file is attempted to be closed. This may be a stupid question, but why can I not save data to a file on my computer if running the VI on "PXI2"?
3.) Assuming the saving of each waveform to a binary file is working (read: (2) is successfully addressed), how can I also write the timestamp of the starting trigger for the waveform along with the waveform in the binary file? An example VI of how I can accomplish this would be fantastic, but I haven't been able to find one thus far.
4.) When I was messing around and trying to accomplish this, it seemed that doing this writing may slow down the entire process too much. I need to record data to the extent of the sawtooth waveform generated by the niFGEN AWG for each trigger. Is there any changes I should make to my acquisition process in the niSCOPE section so that I can read each waveform, along with keeping the timestamp for each, and write this information to a binary file?
I need to get this working quickly, so any help on this is greatly appreciated. Thanks in advance.
Attachments:
5124_update.vi ‏157 KB

Thank you so much for your reply, David. Let me try and explain my
situation and setup a little better, as well as discuss the points you
made in your reply. Beware, you may want to refill your coffee as this
post is long .
I am using an embedded controller in a PXI-1044 chassis. I now have the
chassis hooked up to our local network, and I am deploying my project
to the chassis over the network as I am also connected to the local
network. I have an oscilloscope next to me that takes as input the
pulse train for a trigger and the generated sawtooth from the niFGEN
for each trigger (rising edge of the pulse train from the 6602
counter). Just to make sure synchronization is taking place, the
sawtooth is also fed as input to the niSCOPE for acquisition.
"PXI2" is what shows up when I choose to run a VI on the PXI chassis
rather than "My Computer"; not sure why the 2 is there either, but that
is what it says. I may have tracked down the issue I was having with
writing, but more about that a little later...
The attached VI is an update, although not much has changed. My
application design is like this (keep in mind that some values for VI's
are still constants in the block diagram while others are controls on
the front panel): I am using the 6602 to generate a 1 KHz pulse train
and routing this pulse train to PXI_Trigger0/RTSI0. I am also using the
PXI_Clock (10) as a sample clock for this, and also using this same
clock as the reference clock for both the 5422 and the 5124 (as per the
synchronization help file mentioned for synchronizing multiple
devices). Both the 5422 and the 5124 are triggered by a digital rising
edge (from the pulse train) on PXI_Trigger0/RTSI0 (as it was routed
there). For each trigger, the niFGEN generates a sawtooth waveform
using a stepped trigger mode and outputs it. For each trigger, the
niSCOPE acquires data. They are both synchronous, which is tough to see
since one has its trigger source on the front panel and the other has
its trigger source on the block diagram. All devices use PXI_Clock so
they are synchronized.
The expected behavior is to only generate a single sawtooth waveform
per trigger with a certain number of sample points. I want to acquire
the same number of samples using the niSCOPE, which is what I meant by
"the extent of the waveform" in my previous post. So, should I change
the 8192 to 1000 for the number of samples for the niSCOPE? What would
you recommend for the sampling rate? I have been using 5 MHz for the
niFGEN and 5 MHz for the niSCOPE...this is how it should be done,
correct? If it is different in the VI, please let me know. For some
reason, I have to adjust all of the values each time I open it since
the default values are not the ones I want.
I want to generate and acquire one waveform per trigger (one waveform
per record). However, I want to be able to record a large number of
records so I have enabled the circular buffer-like treatment of the
acquired waveforms. The 100 or 1000 records is actually just a number I
am giving it for now to make sure it is working before recording many
more records.
As for saving the niSCOPE data, I would like to save all data in a
single file that is NOT ascii (to save space). I have been looking at
the HWS file format, and would like to use it. I think the attached VI
includes this at the bottom of the while loop. For each trigger, I
would like to save the time (as accurate as possible) that the trigger
occurred for the record/waveform, which appears to be (absoluteInitialX
- relativeInitialX) as you said in your post (thanks!). I just need to
store as much information about the waveform and time information for
it as possible with the waveform in the file. So it looks like I will
need to use the wfm info for that information, providing portions of it
as waveform attributes in the HWS VI's?
What format of data do you recommend I fetch, and will I be fetching a
"Single waveform" or "Multiple waveforms"? Should I use I32, DBL, WDT,
or other for the format? A balance between good precision in values and
time it takes to fetch/record would be best.
Given all of the above, I am having one troube with saving data to a
file. As a reminder, I am deploying the project to the chassis over the
network. When I choose a location and/or file to save the HWS data to,
I only get choices that are on the PC's hard disk (such as C:\Documents
and Settings\cgifford\...) NOT the chassis's hard disk. When I choose
something other than "C:\" I get an error that the file could not be
opened. However, when I choose "C:\" everything goes fine. The saved
data is nowhere to be found on my PC though, so I am assuming that it
is being stored on the internal 60G hard disk in the chassis that must
be named "C" by default or something!?
I have been told by phone support that I should be able to make a
direct connection with the chassis just like another PC, and should be
able to access the information on its internal hard disk in a drag and
drop fashion. I however cannot directly connect to the PXI chassis to
get the data that has been saved on the hard disk. We are running
Windows XP on the PC. We did some poking around and noticed that the
chassis is not running Windows file sharing, and only has ftp and http
running. We tried to access it using ftp, but we didn't have a username
and password to supply it. So, how can we enable Windows file sharing
on the chassis? How can I connect to it to do drag and drop to get
saved waveform data off of it? This is the main problem I am now
facing. Eventually we would like to store data to an external hard disk
connected to the chassis, which assumes that I can have access to the
internal storage to tell it to save files to the external hard disk.
For now saving it to the internal hard disk is just fine until
everything is proven to work, but I would like to get the data off of
the internal hard drive to put on another computer.
Any answers/suggestions on my above questions are greatly appreciated.
I also want to thank you for reading this long post . I eagerly await
a reply. Thanks again in advance.
Chris
Attachments:
5124_update.vi ‏143 KB

Multi-Org Setup

Hi,
I am having task to upgrade 11.5.10 to R12, but Multi-Org setup is mandatory for upgrade to R12.
Can you guy provide me the document where I can find patches to be applied for Multi-Org Setup.
Regards,
Raj

I am having task to upgrade 11.5.10 to R12, but Multi-Org setup is mandatory for upgrade to R12.
Can you guy provide me the document where I can find patches to be applied for Multi-Org Setup.This question was asked and answered many times in the forum before, please see old threads for the links you need to refer to.
https://forums.oracle.com/forums/search.jspa?threadID=&q=Multi-Org++AND+Setup&objID=c3&dateRange=all&userID=&numResults=15&rankBy=10001
https://forums.oracle.com/forums/search.jspa?threadID=&q=Multi-Org++AND+Setup+AND+R12&objID=c3&dateRange=all&userID=&numResults=15&rankBy=10001
https://forums.oracle.com/forums/search.jspa?threadID=&q=Multi-Org++AND+Setup+AND+Upgrade&objID=c3&dateRange=all&userID=&numResults=15&rankBy=10001
Thanks,
Hussein

Mouse pointer is unchangeable at 100% scaling in multi monitor setup with different resolutions

Hi there, I have been asked by one of the moderators of the Windows 8.1 forums to post this topic here. You can see the thread relating to this post here
http://answers.microsoft.com/en-us/windows/forum/windows8_1-tms/cant-change-the-cursor-pointer/ae8ad8a0-3ded-4810-a3be-794f6c4830a4?msgId=2bd7082f-f5d1-4b01-8c70-e0d2a754d66f&page=1<o:p></o:p>
The problem: The mouse pointer becomes unchangeable in size, type, trails etc when 100% scaling is used. As in it reverts to the standard small white non-inverted, no trails,
no shadow 'pointer', no matter what options you select in the 'Mouse' control panel settings.<o:p></o:p>
This appears to be a scaling problem with the Windows 8/8.1 display, not an actual mouse problem. Judging by my own and other peoples experience it seems to happen mainly with multi
monitor setups where different screen resolutions are used. The issue occurs typically when 100% scaling for all monitors is used or this option is un-ticked and the 'change the size of all items' is on smallest (equivalent to 100%). <o:p></o:p>
If the scaling is set to 150% or greater the issue disappears and the mouse pointer becomes fully functional. Also bizarrely when the scaling is set to 100% if the screen is recorded
using a screen capture program, the recording of the screen shows the mouse pointer selected in the mouse options and not the default small white cursor that is present when recording it. Here is a link to a video where I explain and show the problem
happening on my system. http://youtu.be/xs2cxoeaq-A<o:p></o:p>
I have every update installed without exception, latest drivers etc. I use a 55" 4k screen with 2x1080p monitors in portrait on either side. All are connected through 1 Nvidia
GTX 780 6GB graphics card<o:p></o:p>
Hope you can help us<o:p></o:p>
thanks<o:p></o:p>
Jon M<o:p></o:p>

Hi Jon,
I'm looking into this issue but it will take me some time to provide a reply.
In the meantime I noticed that you have 3 monitors with 1x 55' and 2x27' - please have a try to only connect 1x27' monitor and see if issue persists.
Also please try to change the screen resolution to a lower size and see if issue persists.
Both suggestions are not solution, I just would like to know if it is related to multiple monitor or screen resolution.
If you have any feedback on our support, please send to [email protected]

Multi SSID problem, not work

hi
I bought a Cisco WRVS4400n to use with different vlan and ssid, I use a Cisco Catalyst behind my new WRV, on sigle ssid mode and without Vlans configured, worked perfectly, but, on trunking mode with multi ssid on different vlans ( to use public and private wifi on differents vlans), doesnt work
this is my configuration
Vlan 3, private, with wpa2
Vlan 6, public, with nocat server.
in port 1 of WRV, trunknig mode, vlan3 tagged, vlan6 tagged
in port 8 of Catalyst, trunking mode, vlan3 tagged, vlan6 tagged
I don't need configure DHCP server, I have on both lans.
wifi clients don't cross trough the router to LANS, my dhcp server don´t give IP to client, becouse can't connect. neither when I force a valid IP address.
thanks

Post a link to the page, please.
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"aichau" <[email protected]> wrote in
message
news:geapsu$iav$[email protected]..
>I use the Dreamweaver to create a web page which have two
popup menus. When
>I
> run the page, it only the first popup menu is come up.
the second one
> never
> show up and give me an error undefined is null or not an
object.
> Is anyone can help
>
> Thank you
>

I can't connect Multi SSID after upgrade IOS 6

hello.
I have some question for solving a problem
I have multi SSID (ex. A : ([WPA2]Auth(PSK)), B : ([WPA2]Auth(802.1X), MAC Filtering))
I updated iPhone to ios6 and now I can connect to A.
But when i tried to connect another SSID(B), i couldn't connect SSID(B)
It occured same issue after deleted Network A
Has anyone else experienced this issue?
help me

I went to the Wi-Fi menu and clicked on the Wi-Fi network and changed the HTTP proxy from off to auto and it now it works.

Financial Analyzer Web access after multi-node setup

hey guys
any idea on the follwoing
Financial Analyzer Web access after multi-node setup
any hints will be helpfull
fadi

Thank you Fadi for this quick idea.
I will try to apply it in our environment.
If we couldn't do it, I think that we have other two options; first options is to reinstall OFA in the Web Server Node where there is a Metalink note states how to move OFA from server to server. The second option is changing the configuration files of OFA to reference the Web Server in the new node.
I will update you with the results.
Regards,
M.Muhtadi

Multi-head setup without xorg.conf

I'm using the newer method of running X without an xorg.conf and want a traditional multi-head setup (a "Normal multi-head" method, allowing a separate X session on each of the monitors).
I would use this to have a different window manager run on each of the screens (something like the following for OpenBox: DISPLAY=:0.1 openbox), perhaps with the aid of Switchscreen.
XRandR will give me one big virtual screen (and is currently how I'm doing it, combined with xnest), but that's not what I want. Any ideas?

WooHoo !
awkwood - You Rock ! I feel like an idiot for not paying closer attention to your first post. I finally realized what you were saying and figured out how to do the downgrade.
If it's 2.12.0 I'd suggest trying 2.11.0 instead.
The most recent update borked my dual display with a similar error message but 2.11 works fine.
I don't use an xorg.conf.
So essentially this seems to be a bug with version 2.12 of the xf86-video-intel driver. I downgraded to ver 2.11 and everything works perfectly. I am running dual monitors at full resolution with no fuss. So again awkwood I thank you !
For other Arch Newbies who have this issue in the mean time until they fix the bug, this is how I did the downgrade.
Step 1:
download the 2.11 package from the link below
http://arm.konnichi.com/extra/os/i686/x … pkg.tar.xz
Step 2:
Open a terminal and cd to the directory where you saved the file
$ cd /home/$USERNAME/Downloads
Step 3:
Use pacman to install the package
sudo pacman -U xf86-video-intel-2.11.0-2-i686.pkg.tar.xz
Finally reboot. When you log back in everything should work fine
Again thanks to awkwood as well as karol, blind, Inxsible and everyone else for their help. Everyone here is so helpful, I am defiantly an Arch user for life. Hopefully they will fix the bug in the next version of the driver. My next step is to see about filling a bug report.

How do I avoid errors on a Multi - monitor setup?

Hi.
I want to use Photoshop CS6 on a Multi - monitor setup, using iGPU multi-monitor + GPU system for 4 monitors.
Preiously, I used Photoshop on a Multi - monitor setup without useing iGPU multi-monitor.
And, Photoshop worked well.
However, when I wanted to use 1 more monitor, my GPU supports only 3 monitors.
Then, I enabled iGPU multi-monitor function. It supports 2 more monitors.
At first, It worked. But, after I use "Free transform", "Transform" or something like these tools, Photoshop hang up!
I couldn't figure out the reason why these errors happened.
I need ways to avoid these errors.
Thanks.

Thanks for viewing this discussion.
Finally, I brok through this problem.
I show you how to do, in case of when you face to this problem.
The way to solve this problem is, simple, "buy a new GPU."
But, there is 1 important point, you should buy a same bland's GPU.
In my case, I have SAPPHIRE'S RADEON HD5670, and I bought SAPPHIRE'S RADEON HD 6450.
I think that Photoshop GPUsniffer was confused about GPU driver.
Because there were 2 drivers -- Radeon and Intel Graphics -- exist.
That's why Photoshop hang up.
For your reference,
Best regards.

LMS 4.0 Multi-Server setup

I have a problem setting up a multi-server setup. On my remote LMS/slave servers, I can import the Peer Certificate from my master LMS server and on the slave servers I can import the Master server cert. However, when I go to the Single Sign-On of the slave server it states that the cert is not installed/valid. So, I go back to the Peer Server Certificate setup and look at the cert imported and states it is valid. All self signed certificates.
Question: Should I make new self signed certs for each server? Or/How do I make new cert within LMS(I believe in the setup you added the values)? Is there a log in LMS that I can check this process?
From reading the docs, I don't see anything. Any insight would be greatly appreciated.
thanks,
John

There is a perl script, sslutil.pl, in your LMS installation (under $nmsroot\MDC\Apache) that will allow you to validate your server's certificate. Assuming a default installation on Windows, you can use:
"C:\Program Files (x86)\CSCOpx\bin\perl.exe" "C:\Program Files (x86)\CSCOpx\MDC\Apache\sslutil.pl"
from a command window
My experience (using 3rd party signed certifcates) is that LMS is very particular abou the ownership (casuser needs to own) of the file and directory in which the certificate and key files are stored.

Multiple chrome windows on a multiple monitor, multi-desktop setup?

Dear all,
I'm having this huge headache because I have a dual monitor setup (imac 27" + second 24" monitor) and I have configured 6 different desktops in it (mountain lion here) where each desktop dual monitor scene has a chrome window (with several tabs each) on each monitor. I do this because i work 90% on SaaS's and as such I need this multi-desktop setup with chrome spread all over it.
Problem: Everytime i reboot the system, all those crhome windows get back to desktop 1 (on both monitors) and I have to painstakingly put each chrome window one by one back into each desktop again. Its really a PITA.
Solution: Anyone can tell me a workaround for this or if I am missing some OSX or chorme trick or tweak that will make the system "remember" where each chrome windows was in each desktop + monitor?
Thanks in advance!
//Ricardo

Peggy,
We have been running 3 separate Forte environments on one server (dev,
test, prod) for over a year now. The environments have been at
different Forte release levels at various times. Darrell is right on
target with the UNIX links and separate fortedef.sh files for each
environment. The links will help reduce disk space. Follow his
instructions and you should be good to go. We have each Forte
environment point to its own database instance also. You can set the
environment variables in each fortedef.sh file to do this. If you keep
multiple versions of Forte on a windows client machine, you will have to
switch the Forte.ini file before starting Forte.
As for security and auditing, I not sure what you are looking for here.
Our application has security and auditing but that it.
Keep in mind, that each Forte environment will be competiting for system
resources on the same server. When we have 3 environments running, we
notice a performance hit. Try to use as few resources as you can. For
example, our test and production environments do not require a
repository server, since we test deployed. So do not start these
processes.
Good luck.
Robert Crisafulli
AMISYS
301-838-7540
Long live Forte...

WRV200 multi SSID problem

Hi. now i'm using WRV200 Router model.(use Multi SSID)
- first and second SSID and encryption method is WPA-PSK, working well and no problem.
- third SSID is working well first day, but next day, can be search SSID, but not getting a IP and connection failed.
(if appear this enter administrator mode, not changed any other information, just click to save settings, then i use third SSID in oneday)
- third SSID encryption method is WEP
- Channels are used to channel 6
- in this case, how can i fixed it?
is this problem, SSID's problems? or channel's proble?
why occur to multi SSID problem?
pls help me

The goal is to create one WLAN (wifi) with wpa2 and mac filtering that connect direcly to the physical network with server access, and the other WLAN (public) with only wpa2 protection and in isolated VLAN, for the guest.
Suppose to have two SSID wifi and public (the second in the router web ui), both WPA2 Personal w/o MAC Filtering and w/o VLAN.
I use only PC.
With my laptop (windows 7) and two other laptop (win XP, win 7), I can see both SSID in wireless list, can connect to the first SSID.
When I try to connect to the second SSID, the connection fail
In the attachment you can see the actual router configuration.
In the page Status -> Wireless LAN, ONLY one SSID is displayed (but is this web ui bug?).
Thanks in advance

Multi SSID

Hi!
We are new to configuring multi SSID for WIFI networks. We have one "CISCO WAP4410N" and one "CISCO SG 200-50 50-Port Gigabit Smart Switch". The switch is working on default vlan1. The domain users are getting IP Addresses from Windows DHCP Server. We have created a sub interface for our default LAN Network in our Firewall and assigned it a VLAN id of 100 and same thing on our WAP. There are now two SSIDs, one for domain users and another for visitors.
Wireless for Domain Users is working fine but the Visitors are unable to get the IP addresses from our Firewall DHCP. We know this is due to the missing configuration in the switch.
Can we have the commands or screen shots of the "SG 200-50 50-Port Gigabit Smart Switch" VLAN configuration as per our requirements?
Secondly, what should be the proper settings as per the attached screen shot. Should we tag the default vlan1 or leave it untagged and what should be the priority settings?
Thanks.

This document provides a configuration example for a guest wireless LAN (WLAN) and a secure internal WLAN that use WLAN controllers (WLCs) and lightweight access points (LAPs). In the configuration in this document, the guest WLAN uses web authentication to authenticate users and the secure internal WLAN uses Extensible Authentication Protocol (EAP) authentication.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/70937-guest-internal-wlan.html

Multi-SSID Setup

Similar Messages

Maybe you are looking for