Multi-threaded Render is Slow

I just built a new core i7 965EE system (4c/8t) running at 3.2GHz/c+t.
However, rendering is no faster than my dual-core system though. The processors are only being used from 20-25% each instead of pegging all 4/8 at 100%. Is there a switch or a setting I need to engage? I'm miffed.
Thanks!
[core i7 965EE 3.2GHz, 12GB DDR3, all SAS RAID 0, 16GB i-RAM DDR drive, Vista Ultimate 64bit]

I have also noticed that Premiere CS3 only uses about 35% of the available cpu with Vista 64 whereas it used to be pegged at about 100% with XP 32. However, the encoding does not seem to be any slower, although I have no measurements to know for sure. Things just seem to run as fast or faster.

Similar Messages

CS6 After Effects PNG export very slow - Not Multi-Threaded?

I am rendering an after effects project consisting of over 320,000 source frames of 4000x4000 resolution, outputting over 250,000 frames as PNG files.
Rendering is instant on our machines, all time is spent "compressing and writing" frames. It is taking forever.
We have several machines that are all windows 7, with 16 physical cores, 64GB ram, connected to a 4Gbit SAN.
I did some experimenting, tried using all 16 cores, or 8 cores, or disabled multi-frame rendering even. When this project is rendering my cpu usage is almost non existent,. maybe 1%-5% at times.
with 16 frames at a time being rendered it is averaging between 1 and 7 seconds per frame depending on the content of the frame.
Does Adobe have any plans to multi-thread the PNG exporter? or is there a faster 3rd party plugin out there i could use? It is very slow and doesn't tax the CPU's at all. Even on a single core it doesnt even use 100% cpu while its saving.
I even tried loading one of the frames into photoshop and simpy hit save as a PNG and it took almost 15 seconds to compress and save. I did it again without compression and it saved the 40MB raw file instantly.
That is terrible performance for machines like mine that are pretty much the fastest things out there.
Thanks!

I appreciate your attempt for a workaround solution, however as you well know you can't render to a video file from multiple machines. we must output directly to individual frames, I setup 8 machines to work on this project, if we did not use compression then we would be writing over 300MB/sec of data which would not be good for our fibre network which unfortunatly is only 4Gbit. And it would be about 10TB of data total.
As for your workaround Im not sure we could gain speed with your method either way. spending the extra time to encode to a lossless format and then process again in AME sounds like it would take even more time, unless AME could create PNG files at some sort of ridiculous speed maxxing out every core at 100% or something to compress the PNG's. Out of curiosity I will throw some frames at AME and see how long it takes to compress and how much cpu it will use.
thanks

"Inconsistent cursor cache. Out of range cursor" error on dual processor multi thread

I have a C++ with Pro*C++ COM object running on a Win2000 OS on
a dual processor Middleware. The program is being called by a
service in a multi threaded way. An oracle error like ORA-2103
and SQL-02103 will be generated after running the program. We've
tried putting mutex on every SQL statement in Pro*C and it works
but the systems became very very slow. We concluded that the
error might be cause by a collision of threads accessing the
same Table or different tables having foreign constraints. This
is so because the error keeps coming from a statement accessing
Table A and following errors comes from a Table B having a
foreign key on Table A.
Our only solution now is to put Mutex on Statements accessing
same tables or tables with foreign constraints but this will
make our system run very very slow. I dont know if the problem
is in our Oracle Database because we already upgraded our system
from 8.1.6 to 8.1.7. The wierd thing on this is that the system
is running smoothly without oracle errors on a SINGLE PROCESSOR
Middleware. Hope you can give me any insights on this problem.

I have a C++ with Pro*C++ COM object running on a Win2000 OS on
a dual processor Middleware. The program is being called by a
service in a multi threaded way. An oracle error like ORA-2103
and SQL-02103 will be generated after running the program. We've
tried putting mutex on every SQL statement in Pro*C and it works
but the systems became very very slow. We concluded that the
error might be cause by a collision of threads accessing the
same Table or different tables having foreign constraints. This
is so because the error keeps coming from a statement accessing
Table A and following errors comes from a Table B having a
foreign key on Table A.
Our only solution now is to put Mutex on Statements accessing
same tables or tables with foreign constraints but this will
make our system run very very slow. I dont know if the problem
is in our Oracle Database because we already upgraded our system
from 8.1.6 to 8.1.7. The wierd thing on this is that the system
is running smoothly without oracle errors on a SINGLE PROCESSOR
Middleware. Hope you can give me any insights on this problem.

"SQL-02103: Inconsistent cursor cache." error on a dual processor multi threaded apps

I have a C++ with Pro*C++ COM object running on a Win2000 OS on
a dual processor Middleware. The program is being called by a
service in a multi threaded way. An oracle error like ORA-2103
and SQL-02103 will be generated after running the program. We've
tried putting mutex on every SQL statement in Pro*C and it works
but the systems became very very slow. We concluded that the
error might be cause by a collision of threads accessing the
same Table or different tables having foreign constraints. This
is so because the error keeps coming from a statement accessing
Table A and following errors comes from a Table B having a
foreign key on Table A.
Our only solution now is to put Mutex on Statements accessing
same tables or tables with foreign constraints but this will
make our system run very very slow. I dont know if the problem
is in our Oracle Database because we already upgraded our system
from 8.1.6 to 8.1.7. The wierd thing on this is that the system
is running smoothly without oracle errors on a SINGLE PROCESSOR
Middleware. Hope you can give me any insights on this problem.

I have a C++ with Pro*C++ COM object running on a Win2000 OS on
a dual processor Middleware. The program is being called by a
service in a multi threaded way. An oracle error like ORA-2103
and SQL-02103 will be generated after running the program. We've
tried putting mutex on every SQL statement in Pro*C and it works
but the systems became very very slow. We concluded that the
error might be cause by a collision of threads accessing the
same Table or different tables having foreign constraints. This
is so because the error keeps coming from a statement accessing
Table A and following errors comes from a Table B having a
foreign key on Table A.
Our only solution now is to put Mutex on Statements accessing
same tables or tables with foreign constraints but this will
make our system run very very slow. I dont know if the problem
is in our Oracle Database because we already upgraded our system
from 8.1.6 to 8.1.7. The wierd thing on this is that the system
is running smoothly without oracle errors on a SINGLE PROCESSOR
Middleware. Hope you can give me any insights on this problem.

"SQL-02103 Inconsistent cursor cache." error on dual processor multi threaded system

I have a C++ with Pro*C++ COM object running on a Win2000 OS on
a dual processor Middleware. The program is being called by a
service in a multi threaded way. An oracle error like ORA-2103
and SQL-02103 will be generated after running the program. We've
tried putting mutex on every SQL statement in Pro*C and it works
but the systems became very very slow. We concluded that the
error might be cause by a collision of threads accessing the
same Table or different tables having foreign constraints. This
is so because the error keeps coming from a statement accessing
Table A and following errors comes from a Table B having a
foreign key on Table A.
Our only solution now is to put Mutex on Statements accessing
same tables or tables with foreign constraints but this will
make our system run very very slow. I dont know if the problem
is in our Oracle Database because we already upgraded our system
from 8.1.6 to 8.1.7. The wierd thing on this is that the system
is running smoothly without oracle errors on a SINGLE PROCESSOR
Middleware. Hope you can give me any insights on this problem.

I have a C++ with Pro*C++ COM object running on a Win2000 OS on
a dual processor Middleware. The program is being called by a
service in a multi threaded way. An oracle error like ORA-2103
and SQL-02103 will be generated after running the program. We've
tried putting mutex on every SQL statement in Pro*C and it works
but the systems became very very slow. We concluded that the
error might be cause by a collision of threads accessing the
same Table or different tables having foreign constraints. This
is so because the error keeps coming from a statement accessing
Table A and following errors comes from a Table B having a
foreign key on Table A.
Our only solution now is to put Mutex on Statements accessing
same tables or tables with foreign constraints but this will
make our system run very very slow. I dont know if the problem
is in our Oracle Database because we already upgraded our system
from 8.1.6 to 8.1.7. The wierd thing on this is that the system
is running smoothly without oracle errors on a SINGLE PROCESSOR
Middleware. Hope you can give me any insights on this problem.

"SQL-02103: Inconsistent cursor cache." error on dual processor multi thread apps

I have a C++ with Pro*C++ COM object running on a Win2000 OS on
a dual processor Middleware. The program is being called by a
service in a multi threaded way. An oracle error like ORA-2103
and SQL-02103 will be generated after running the program. We've
tried putting mutex on every SQL statement in Pro*C and it works
but the systems became very very slow. We concluded that the
error might be cause by a collision of threads accessing the
same Table or different tables having foreign constraints. This
is so because the error keeps coming from a statement accessing
Table A and following errors comes from a Table B having a
foreign key on Table A.
Our only solution now is to put Mutex on Statements accessing
same tables or tables with foreign constraints but this will
make our system run very very slow. I dont know if the problem
is in our Oracle Database because we already upgraded our system
from 8.1.6 to 8.1.7. The wierd thing on this is that the system
is running smoothly without oracle errors on a SINGLE PROCESSOR
Middleware. Hope you can give me any insights on this problem.

I have a C++ with Pro*C++ COM object running on a Win2000 OS on
a dual processor Middleware. The program is being called by a
service in a multi threaded way. An oracle error like ORA-2103
and SQL-02103 will be generated after running the program. We've
tried putting mutex on every SQL statement in Pro*C and it works
but the systems became very very slow. We concluded that the
error might be cause by a collision of threads accessing the
same Table or different tables having foreign constraints. This
is so because the error keeps coming from a statement accessing
Table A and following errors comes from a Table B having a
foreign key on Table A.
Our only solution now is to put Mutex on Statements accessing
same tables or tables with foreign constraints but this will
make our system run very very slow. I dont know if the problem
is in our Oracle Database because we already upgraded our system
from 8.1.6 to 8.1.7. The wierd thing on this is that the system
is running smoothly without oracle errors on a SINGLE PROCESSOR
Middleware. Hope you can give me any insights on this problem.

The speed of multi threads

I desing a program to test the speed of using multi threads to add up from 0 to 1000000000
As I know from some books ,I assumed that the multithread to caculate should faster than single thread , but what supprised me is that I was wrong , the result is that : 5 threads is slower than single thread ,and so did 10 threads slower than 5 threads !
why ?

"Adding up" a sequential series of numbers doesn't
sound like a good application for multithreading.How
did you divide up the responsibility among multiple
threads?You use a divide-and-conquer strategy. The sequence is
split into halves recursively down to a certain depth
(sequence length) and distributed among the avilable
processors.Thanks for the explanation, but I understand that - I assumed (perhaps incorrectly) that the OP is testing on a single-processor system (one reason why the threading didn't improve performance as expected) or that the actual code to accomplish the multithreading was improperly implemented (another reason). That's why I asked what the OP did to divide up the responsibility. :o)

The CPU utilization is 0% for the other remaining processes when multi threading is used

I am new to AE ,so I am trying to render a project enabling multi threading process the additional processes are present but their utilization is 0% .
I want to juice out every single CPU utiliaztion .
ANy help is greatly appriciated,.
My system specs:
AMD 9690 4.7 Ghz 8 core
32 GB DDR3
C:\256 GB Solid Satte Raid 0
GeForce 780 Ti DDR5 3GB

It is very tempting to try and use all of your system resources and multiprocessing for all your projects, but this is not the way After Effects works. Many third-party plug-ins, many codecs, and many operations do not respond well to multiprocessing. All it takes is one process in your entire thread that is not MP aware to foul the whole thing and give you longer render times.
You are also leaving zero processors for the rest of your computer. Not a wise idea.
After effects renders one frame at a time. One HD frame even with multiple layers of pixel processing just isn't that much data. It does take a while to do the calculations, but expecting to have every one of your CPUs jacked up at 100% to render a single frame of video is expecting an awful lot.
I would suggest that you read up on optimizing After Effects for your computer. Do not expect to be able to utilize 100% of your system resources at all times. That's just not the way processing video on a pixel by pixel basis works.
Just a little FYI, for 99% of my projects in After Effects I have render multiple frames simultaneously turned off. It just doesn't work with most of the things I do. Sorry for the disappointment.

VI calling from a multi-thread Teststand

Hello,
My test system tests four UUTs at the same time(with batch mode in TS), the code is based on LabVIEW and call from TS, so every step the same VI will be accessed by four thread. however, it runs quite slow even i set the reentrant execution in VI propertise.
My Quesition:
Can I do it like this in multi-thread mode of TS?
How can I make it fast? (convert VI to dll?????)
Any help will be appreciated.
Thanks,Steven

Hello Allen,
Thanks for your help.
Problem: I have a LabVIEW VI with parallel code blocks. These blocks run in parallel as expected when I run my VI directly or from a top level VI. However, the code blocks seem to run sequentially when I call my VI from TestStand. Why is this happening and how can I fix it?
Solution: In order to fix this behavior, simply set the VI Properties of "Execution" of your LabVIEW VI to "Other 1" or "Other 2". This change will make the parallel code blocks in your LabVIEW VI run in parallel as expected. To change this setting, from your LabVIEW VI, go to File»VI Properties. Select the Execution category. Change the Preferred Execution System to be either other 1 or other 2.
You need to make this change to any LabVIEW VI with parallel code blocks that is called from TestStand. The reason for this is that TestStand is using the LabVIEW ActiveX interface to run LabVIEW VIs. The LabVIEW ActiveX interface sets the caller's execution system to "User Interface" by default. This execution system is not recommended for a VI with parallel code blocks. If your LabVIEW VI's execution system is set to "Same as caller" (which is the default setting when creating a new LabVIEW VI), then it is executed in the User Interface thread when run through the LabVIEW ActiveX interface. This prevents the blocks to be executed in parallel.
In fact, only one block in my LabVIEW code, but it accessed by four thread from TS. I am sure that my VI can be accessed by four thread simultaneously if I enable the reentrant excution in VI property. I also have tried what mentioned in above document but no use.
However, if i only add a 1000ms delay to my LabView code instead of the 'calculation', it is fast enough! what is happening or something i set wrong?
I don't want to convert all my LabView code to DLL cos too many VIs here, and difficult for mantenance either.
Any other good solution???
Thank you Allen...
Steven

Is rendering in Final Cut single thread or multi thread?

There seems to be this recurring message about how the new Macpros perform single-threaded tasks about the same as the previous gen of Macpros, however in multi-threaded tasks the new Pros shine.
How do I know if a task is single-threaded or multi-threaded? I do a lot of rendering video filters, generators, effects, etc. in Final Cut. Even something as (seemingly) simple as generating scrolling credits takes forever to render.
Is video rendering a multi-threaded task? Will I see time significant time savings in rendering with the new Pro machines?

It's not right now but the new Mac Pros are faster in single-threaded modes anyway:
http://www.macrumors.com/2009/03/14/updated-mac-pro-benchmarks-and-video-of-inte rnals/
Turns out the initial benchmarks were incorrect. The integrated memory controller is a MASSIVE performance boost. But it is inevitable that Apple will eventually choose the multi-threaded route for Final Cut Studio anyway, even if they do not at the present.

SSRS - Is there a multi thread safe way of displaying information from a DataSet in a Report Header?

In order to dynamically display data in the Report Header based in the current record of the Dataset, we started using Shared Variables, we initially used ReportItems!SomeTextbox.Value, but we noticed that when SomeTextbox was not rendered in the body
(usually because a comment section grow to occupy most of the page if not more than one page), then the ReportItem printed a blank/null value.
So, a method was defined in the Code section of the report that would set the value to the shared variable:
public shared Params as String
public shared Function SetValues(Param as String ) as String
Params = Param
Return Params
End Function
Which would be called in the detail section of the tablix, then in the header a textbox would hold the following expression:
=Code.Params
This worked beautifully since, it now didn't mattered that the body section didn't had the SetValues call, the variable persited and the Header displayed the correct value. Our problem now is that when the report is being called in different threads with
different data, the variable being shared/static gets modified by all the reports being run at the same time.
So far I've tried several things:
- The variables need to be shared, otherwise the value set in the Body can't be seen by the header.
- Using Hashtables behaves exactly like the ReportItem option.
- Using a C# DLL with non static variables to take care of this, didn't work because apparently when the DLL is being called by the Body generates a different instance of the DLL than when it's called from the header.
So is there a way to deal with this issue in a multi thread safe way?
Thanks in advance!

Hi Angel,
Per my understanding that you want to dynamic display the group data in the report header, you have set page break based on the group, so when click to the next page, the report hearder will change according to the value in the group, when you are using
the shared variables you got the multiple thread safe problem, right?
I have tested on my local environment and can reproduce the issue, according to the multiple safe problem the better way is to use the harshtable behaves in the custom code, you have mentioned that you have tryied touse the harshtable but finally got
the same result as using the ReportItem!TextBox.Value, the problem can be cuased by the logic of the code that not works fine.
Please reference to the custom code below which works fine and can get all the expect value display on every page:
Shared ht As System.Collections.Hashtable = New System.Collections.Hashtable
Public Function SetGroupHeader( ByVal group As Object _
,ByRef groupName As String _
,ByRef userID As String) As String
Dim key As String = groupName & userID
If Not group Is Nothing Then
Dim g As String = CType(group, String)
If Not (ht.ContainsKey(key)) Then
' must be the first pass so set the current group to group
ht.Add(key, g)
Else
If Not (ht(key).Equals(g)) Then
ht(key) = g
End If
End If
End If
Return ht(key)
End Function
Using this exprssion in the textbox of the reportheader:
=Code.SetGroupHeader(ReportItems!Language.Value,"GroupName", User!UserID)
Links belowe about the hashtable and the mutiple threads safe problem for your reference:
http://stackoverflow.com/questions/2067537/ssrs-code-shared-variables-and-simultaneous-report-execution
http://sqlserverbiblog.wordpress.com/2011/10/10/using-custom-code-functions-in-reporting-services-reports/
If you still have any problem, please feel free to ask.
Regards
Vicky Liu

Memory leaks and multi threading issues in managed client.

In our company we use a lot of Oracle, and after the release of the managed provider we migrated all applications to it. First the things were very impressive : the new client was faster, but after some days applications that uses 100MB with old client goes to 1GB and up. The memory is not the only issue, we use a lot of multi threading, and we experience connection drops and not disposal, after 1 days working one of the application had over 100 sessions on the server. I think there is something wrong with connection pool and multi threading.
Is someone experience same problems.
Yesterday we went back with unmanaged provider. Now things are back to normal.

connection drops: did you try to use "Validate Connection=true" parameter in your connection string?
the new client was faster: are you sure with this statement? Even in 64bit environment? I got quite serious performance problems when running application under 64bit process: https://forums.oracle.com/thread/2595323

How to write a multi threaded Cache Event Listener

I have a distributed data cache called tokenCache for my application. I have also added a mapListener to this cache to listen to a particular kind of events.
tokenCache.addMapListener((MapListener) new TokenCacheListenerBean(), new MapEventFilter(tokenFilter), false);
So bascially everytime a token (The domain object of this cache) is updated the entryUpdated() method in my EJB TokenCacheListenerBean is invoked.
The issue I have though is that, from what I observe on running my code is that the Cache Listener is single threaded. So if two Token Objects on my tokenCache are updated,
lets say Token Object A and Token Object B one after the other, the entryUpdated() method in my EJB is invoked for Token Object A and once the invocation is complete
then the entryUpdated() method is invoked again for Token Object B(). At a given point of time there is only one instance of TokenCacheListenerBean EJB. Is there a way to
make this happen in multi-threaded manner ?
Is there a configuration setting somewhere which allows multiple CacheListeners to be instantiated at a given point of time ?
TokenCacheListenerBean EJB_
package oracle.communications.activation.asap.ace;
import java.util.Iterator;
import java.util.Set;
import java.util.logging.Logger;
import javax.ejb.Stateless;
import com.tangosol.net.NamedCache;
import com.tangosol.util.MapEvent;
import com.tangosol.util.MapListener;
import com.tangosol.util.ValueUpdater;
import com.tangosol.util.extractor.PofExtractor;
import com.tangosol.util.extractor.PofUpdater;
import com.tangosol.util.filter.EqualsFilter;
import com.tangosol.util.filter.LikeFilter;
import com.tangosol.util.filter.LimitFilter;
import com.tangosol.util.processor.UpdaterProcessor;
* Session Bean implementation class TokenCacheListenerBean
@Stateless
public class TokenCacheListenerBean implements TokenCacheListenerBeanRemote, TokenCacheListenerBeanLocal, MapListener {
NamedCache asdlCache;
NamedCache tokenCache;
private final int PAGE_SIZE = 1;
private static Logger logger = Logger.getLogger(ConnectionManager.class.getName());;
* An instance of the JCAModeler EJB, represents the JCA-JNEP
JCAModeler jcaBean;
* Default constructor.
public TokenCacheListenerBean() {
// TODO Auto-generated constructor stub
public void entryDeleted(MapEvent Event) {
public void entryInserted(MapEvent Event) {
public void entryUpdated(MapEvent Event) {
Token newToken = (Token) Event.getNewValue();
Token oldToken = (Token) Event.getOldValue();
if ((oldToken.getState() == Token.TOKEN_RESERVED)
&& (newToken.getState()== Token.TOKEN_AVAILABLE)) {
String networkID = newToken.getNeID();
asdlCache = AceCacheFactory.getCache("asdlCache");
tokenCache = AceCacheFactory.getCache("tokenCache");
EqualsFilter filterNE = new EqualsFilter(new PofExtractor(String.class,Asdl.NETWORKID), networkID);
LimitFilter limitFilter = new LimitFilter(filterNE, PAGE_SIZE);
Set removeASDL = asdlCache.keySet(limitFilter);
Iterator asdlIterator = removeASDL.iterator();
if (asdlIterator.hasNext()) {
logger.info(printASDLCache());
ValueUpdater updater = new PofUpdater(Token.STATE);
System.out.println("Token ID:" + newToken.getTokenID());
UpdaterProcessor updaterProcessor = new UpdaterProcessor(updater, Integer.toString(Token.TOKEN_RESERVED));
tokenCache.invoke(newToken.getTokenID(), updaterProcessor);
jcaBean = new JCAModeler(tokenCache);
Object asdlID = asdlIterator.next();
Asdl provisionAsdl = (Asdl) asdlCache.get(asdlID);
asdlCache.remove(asdlID);
jcaBean.provision(provisionAsdl, newToken.getTokenID());
logger.info(ConnectionManager.printTokenCache());
logger.info(printASDLCache());
}

Here is what I am asking!
I have added 2 listeners (Listener A and Listener B) which each listen on for changes made to 2 different token Cache Objects (Token A and Token B).
for (i = 0; i < 2 ; i++) {
Token tokenAdded = new Token(UUID.randomUUID().toString(),TOKEN_AVAILABLE, networkID);
tokenCache.put(tokenAdded.getTokenID(), tokenAdded);
     tokenCache.addMapListener((MapListener) new TokenCacheListener(), tokenAdded.getTokenID(), false);
Now assume that updates are made to Token A and Token B simuntaneosly.
Why do i observe in my diagnostic messages that only one Listener is invoked at a given point of time.
Which means I see Listener A getting invoked and then once invocation of Listener A is complete I see Listener B bieng invoked.
Ideally I would want both listeners to be invoked simultaneously rather than in a one off fashion.
Here is the code for my token cache Listener
package oracle.communications.activation.asap.ace;
import java.util.Iterator;
import java.util.Map;
import java.util.Set;
import java.util.logging.Level;
import java.util.logging.Logger;
import com.tangosol.net.CacheFactory;
import com.tangosol.net.NamedCache;
import com.tangosol.util.AbstractMapListener;
import com.tangosol.util.Filter;
import com.tangosol.util.MapEvent;
import com.tangosol.util.MapListener;
import com.tangosol.util.ObservableMap;
import com.tangosol.util.ValueUpdater;
import com.tangosol.util.extractor.PofExtractor;
import com.tangosol.util.extractor.PofUpdater;
import com.tangosol.util.filter.AndFilter;
import com.tangosol.util.filter.EqualsFilter;
import com.tangosol.util.filter.LikeFilter;
import com.tangosol.util.filter.LimitFilter;
import com.tangosol.util.processor.UpdaterProcessor;
public class TokenCacheListener extends AbstractMapListener {
     NamedCache asdlCache;
     NamedCache tokenCache;
     AceCacheFactory cacheFactoryBean = new AceCacheFactory();
     private final int PAGE_SIZE = 1;
     private static Logger logger = Logger.getLogger(ConnectionManager.class
               .getName());;
     * An instance of the JCAModeler EJB, represents the JCA-JNEP
     JCAModeler jcaBean;
     * This is a utility method and prints the tokens cache.
     public String printTokenCache() {
          NamedCache tokenCache = cacheFactoryBean.getCache("tokenCache");
          LikeFilter tokenList = new LikeFilter(new PofExtractor(String.class,
                    Token.STATE), "%", (char) 0, false);
          Set keySet = tokenCache.keySet(tokenList);
          StringBuffer cachedTokenList = new StringBuffer("\n################################## Token(s) Cache ##################################");
          int counter = 1;
          for (Object tokenInCache: keySet) {
               Token tokenObject = (Token) tokenCache.get(tokenInCache.toString());
               cachedTokenList.append("\nS.NO:" + (counter++)
                         + "\t ID:" + tokenInCache.toString()
                         + "\t State:" + Token.tokenToString(tokenObject.getState()));
          cachedTokenList.append("\n####################################################################################");
          return cachedTokenList.toString();
     * This method is a utility method and it prints all the ASDL(s) currently present on the
     * asdlCache.
     private String printASDLCache() {
          NamedCache asdlCache = cacheFactoryBean.getCache("asdlCache");
          LikeFilter asdlList = new LikeFilter(new PofExtractor(String.class,
                              Asdl.NETWORKID), "%", (char) 0, false);
          Set keySet = asdlCache.keySet(asdlList);
          StringBuffer cachedASDLList = new StringBuffer("\n################ ASDL Cache ######## ########");
          int counter = 1;
          for (Object asdlInCache: keySet) {
               cachedASDLList.append("\nS.NO:" + (counter++) + "\t ID:" + asdlInCache.toString());
          cachedASDLList.append("\n################ ASDL Cache ######## ########\n");
          return cachedASDLList.toString();
     public TokenCacheListener() {
     public void checkASDLCache(MapEvent Event) {
     // Not currently used
     public void entryUpdated(MapEvent Event) {
          Token newToken = (Token) Event.getNewValue();
          Token oldToken = (Token) Event.getOldValue();
          logger.info("\n=============================================================================================="
                    + "\nTOKEN CACHE LISTENER"
                    + "\n=============================================================================================="
                    + printTokenCache()
                    + "\n==============================================================================================");
          if ((oldToken.getState() == Token.TOKEN_RESERVED)
                    && (newToken.getState()== Token.TOKEN_AVAILABLE)) {
          String networkID = newToken.getNeID();
          asdlCache = cacheFactoryBean.getCache("asdlCache");
          tokenCache = cacheFactoryBean.getCache("tokenCache");
          EqualsFilter filterNE = new EqualsFilter(new PofExtractor(String.class,Asdl.NETWORKID), networkID);
          LimitFilter limitFilter = new LimitFilter(filterNE, PAGE_SIZE);
          Set removeASDL = asdlCache.keySet(limitFilter);
          Iterator asdlIterator = removeASDL.iterator();
          if (asdlIterator.hasNext()) {
          logger.info(printASDLCache());
          ValueUpdater updater = new PofUpdater(Token.STATE);
          System.out.println("Token ID:" + newToken.getTokenID());
          UpdaterProcessor updaterProcessor = new UpdaterProcessor(updater, Integer.toString(Token.TOKEN_RESERVED));
          tokenCache.invoke(newToken.getTokenID(), updaterProcessor);
          jcaBean = new JCAModeler(tokenCache);
          Object asdlID = asdlIterator.next();
          Asdl provisionAsdl = (Asdl) asdlCache.get(asdlID);
          asdlCache.remove(asdlID);
          jcaBean.provision(provisionAsdl, newToken.getTokenID());
          logger.info(printTokenCache());
          logger.info(printASDLCache());
I only see one instance of this listener alive at any given point of time.
Edited by: 807103 on Nov 3, 2011 1:00 PM
Edited by: 807103 on Nov 3, 2011 1:12 PM

Multi-Threaded FTP

Multi-Threaded FTP was a huge attraction for me, and one of the features that sold me on upgrading to Dreamweaver CS6. However, I haven't seen any sign of it in the product or any documentation to help me use it. My files keep transferring in the traditional one-at-a-time way.
Is there something I need to do to enable this feature? Has anybody used this feature yet?

Might not help but I saw this in the comments on David Powers' blog
http://foundationphp.com/blog/2012/04/23/my-verdict-on-dreamweaver-cs6/
"Multi-thread FTP is the default in Dreamweaver CS6. You can neither turn it on nor off. It handles a maximum of three transfers simultaneously in either direction (so you can download at the same time as uploading). However, it doesn’t work with Check In/Check Out."
He also has the following comments in the body of the blog entry:
Multichannel FTP
Let’s be honest. In the past, Dreamweaver’s FTP client was a dog. Not any more. It now supports multichannel transfers, and can even download at the same time as uploading. Orange arrows indicate items queued for transfer. When the transfer begins, the arrow turns green. And if you’re transferring a large item, hovering over the filename displays a tooltip of how much of the file has been transferred. With Dreamweaver CS5.5, it took more than 90 minutes to upload a WordPress site on my internet connection. Now, it’s more than ten times faster.
The FTP error messages are also more meaningful. No one is likely to buy Dreamweaver CS6 for its FTP client alone, but this is a major improvement to the program.

Multi Thread Server over TCP/IP

Multi Thread Server over TCP/IP. Does it work?
In my box it works only over IPC protocol.
null

S C Maturi (guest) wrote:
: Mark Malakanov (guest) wrote:
: : Multi Thread Server over TCP/IP. Does it work?
: : In my box it works only over IPC protocol.
: Mark,
: Multi threaded server over TCP/IP will not work with
: the current distribution of Oracle 8.0.5 on Linux.
: This is corrected and a patch would be released soon.
: Maturi
tcp 0 0 bock.nettek-ll:listener bock.nettek-
llc.co:4196 ESTABLISHED
tcp 0 0 bock.nettek-llc.co:4196 bock.nettek-
ll:listener ESTABLISHED
(I have serveral of these)
TNS Ping Utility for Linux: Version 8.0.5.0.0 - Production on 07-
JAN-99 18:45:52
(c) Copyright 1997 Oracle Corporation. All rights reserved.
Attempting to contact (ADDRESS=(PROTOCOL=TCP)(HOST=localhost)
(PORT=1521))
OK (440 msec)
...and from my install log you see that I selected MTS:
-[ YESNO
Q> Would you like MTS (Multi-Threaded Server) configured
and the SQL*Net$
A> TRUE
Please explain? Will TCP/IP MTS work via the loopback adapter
only? So far I have not tried a remote TCP/IP connection.
-STEVEl
null

Multi-threaded Render is Slow

Similar Messages

Maybe you are looking for