Multicam switch is switching audio

I am trying to switch views on a couple of angles and the audio isn't cooperating.
I have two camera views and a separately recorded audio track for same. I created an in-sync multicam clip, no problem. However, now that I have that multicam clip in the timeline, when I switch between the two views I lose the good audio as soon as I make the cut.
I started by going to the clips multi-angle view in the viewer window and selected the good audio track. I clicked on the filmstrip icon to make it blue and the keyline around the audio icon turned green; as it should. I played back the clip and was able to switch views with the audio remaining from the good audio clip; the two video views now with a blue line around each thumbnail.
With the clip in the timeline I play the clip to where I want to switch views and hit "2" to switch to view 2. When I do, the audio to the left of the cut remains the good audio track, but to the right of the cut the audio switches to the scratch audio of the camera that shot that view. If I move forward in the clip and hit "1" to switch back to view 1, the audio switches to the recording from THAT camera. The good audio clip is rendered useless once the switch cut has been made, never to return.
I followed instructions to a "T" on making the multicam switch and I hope I describe it well enough above to illustrate that fact, but clearly something's not going right. Any clues?

This is the multiclip dropped onto the timeline:
This is the timeline after cutting from "view_A" to "view_B." As you can see, a drastic change in the waveform:
This is the timeline after switching view back to "view_A." A less-drastic change in the waveform but its subtlety shows that neither has it returned to the high-quality audio but instead to the camera's onboard audio:

Similar Messages

  • Duet makes noise after switching between finder audio and Logic

    Hi
    My Duet makes noise after switching between "finder audio" and "Logic", In other words i would play a mp3 in the finder and when returning to Logic all my audio sounds like the "lo-fi" RTAS free plug digidesign gives away now.
    This is happening on a White *iMac 24"*
    Model Name: iMac
    Model Identifier: iMac6,1
    Processor Name: Intel Core 2 Duo
    Processor Speed: 2.33 GHz
    Number Of Processors: 1
    Total Number Of Cores: 2
    L2 Cache: 4 MB
    Memory: 2 GB
    Bus Speed: 667 MHz
    Boot ROM Version: IM61.0093.B07
    SMC Version (system): 1.10f3
    MacOsx 10,5,7

    Does this happen every single time? The same thing happens to me every once in a while. I just close Logic and Maestro and unplug the Duet. Then, in this order, plug in the Duet, wait for it to click, load Maestro, load Logic. Works every time.
    Edit: It does only seem to happen when I switch from Logic and the audio output from the Duet to internal and then come back quickly. I don't think it's an issue with the Duet hardware itself.
    Message was edited by: AecDuck

  • Switch to Switch Connection

    Hi, for one project we are using HP 1910-24G-PoE (170W) Switch (JE008A) switch. There are total six nos. of switches at different floors, out of these six switches one switch is located in main server room.
    My first question is can we use SFP port available on each of five switches & connect it to one fiber patch panel through different LIU's ?
    Sencond question is can we covert these into cat6 (RJ45) again & connect it to 6th switch located in main server room? 
    Thanks.

    Hi Shashikant,
    I given few thought what could be issue and following are few of the guess
    Switch to Switch should be connected with cross cable -- It is connected
    Both the ports should have same speed and duplex setting -- It is shared and OK
    Possible Layer-2 loop - Needs to verify for both switches- Need topology view (if these switches are connected to any other networking devices)
    Output of show cdp nei
    Output of show spanning-tree
    Output of show vtp status
    Shutdown interface and then no shut the interface. Check the logging message on both the switches.
    With this certainly you would be in position to identify the close the problem.
    With regards,
    Shailesh

  • Switch to switch cross cable ?

    Well yesterday i read in a cisco book saying that you should have a cross cable when connecting switch to switch & a straight cable when connecting workstation to a switch , but currently i have stright all through , switch to switch or switch to pc .
    network seems to run fine, why is this ?
    thanks

    Hi Malutaru1234,
    I think you have copied exactly the same lines from my first post without checking that Fasi74 had alraedy replied that he is having 1900 switch.
    Also it is not necessary that he need to configure trunk between the 2 switches when connected via cross over cable becuase trunk is just to pass the information of more than 1 vlan. If you have single vlan in your network you can connect the 2 switches via access link also.
    Regards,
    Ankur

  • Disable portfast on switch-to-switch connection

    Hi,
    From http://www.cisco.com/en/US/customer/tech/tk389/tk621/technologies_configuration_example09186a008009467c.shtml, it says, "do not use portfast when you have switch-to-switch connection. In this case, the command can result in a loop."
    For e.g. when someone connects a switch port(with portfast enabled) to another switch port(with portfast enabled)
    1) can this scenario cause a loop even though the connection between these switch is only a single link?
    2) If it does not cause a loop, what will happen? STP recalculation which causes a short network outage?
    Thanks.
    Christina

    Hi Christina,
    1) Only if there is a redundant physical path between the switches, such as through another switch. If the only physical path between the two switches is the switch-to-switch link in question, then no loop can occur.
    2) Portfast simply ignores the standard STP state transitions and immediately enters the forwarding state, so assuming no loop, a switch-to-switch link that has portfast configured will skip the 50 second STP convergence time and immediately forward traffic.
    HTH,
    Bobby
    *Please rate helpful posts.

  • Cisco 4500X + VSS + Trust Sec Switch to Switch Encryption

    Hi,
    actually im testing and evaluationg the Cisco 4500X switch as new distribution switch for our Company.... Now i have some issues with one of our requirements.
    For security reasons i need to encrypt the links between the 4500X and the access switches in other buildings (no issue with Trust Sec)
    But ... now i also need to encrypt the link between the two 4500X if i run VSS ... my question is .. is it possible to encrypt the VSL link with TrustSec Switch to Switch encryption?
    BR,
    Florian

    Hi Frloian,
    If you have 2 switches in different data centers than you do not need VSS. In fact this is very bad design as the whole concept of VSS is grasped on dual home design. In the essence the proper design of VSS system is to have every downsteram switch connected with one link to one VSS switch and other link to second VSS switch, so that when one VSS switch would fail other can take over. Please look at the VSS best practises:
    http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-virtual-switching-system-1440/109547-vss-best-practices.html#vss_best
    Update:
    There is possibility to encrypt VSL link, but only in 6500 sup2t environment:
    http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/15-0SY/configuration/guide/15_0_sy_swcg/virtual_switching_systems.html#wp1341144

  • Can I switch License switch from PC to mac? AE cs5

    Can I switch License switch from PC to mac? AE cs5

    Platform swaps only apply to current versions. You need to upgrade to CS6 and make the switch.
    http://kb2.adobe.com/cps/405/kb405819.html
    Mylenium

  • Conflict using simultaneously IVI Switch and Switch Executive ?

    Hi,
    I use IVI Switch and Switch Executive libraries in an Labwindows CVI project, and I meet some problems :
    I call SE lib for InitSession/CloseSession/FindRoute and Connect/Disconnect (apply to any switch devices in the SE configuration).
    I call IVI Switch lib for SelfTest and Reset (apply to a single device).
    But when I do an IVI Switch Reset then a Switch Executive Connect or Disconnect, an error occurs : Switch Executive seems to ignore what IVI Switch operations do to the device ?
    Also, can you tell me if :
    niSE_OpenSession performs a self test for the devices in the config ? A reset ?
    niSE_CloseSession performs a reset for the devices in the config ?
    Thanks.

    Hello,
    the niSE session talks to underlying IVI drivers using the IVI Switch session underneath, so any additional opening of IVI Switch session to the same device will cause the two driver sessions (that keep the information about the state of the hardware connections) to be either one or both out of synch with the actual hardware state). Because of the architecture of the underlying IVI drivers, niSE session cannot know if and what someone did to the instrument using IVI Switch session.
    Therefore, it is not adviseable to use IVI Switch session while having another session open to the same device. If you need to use the invasive operations - which is anything that changes the state of the device, such as Reset and possibly self-test (self-test may be implemented as an operation that cycles relays and it may not but you can't be sure), you must make sure that one session is open and closed before another type of session is open.
    The ni Switch Executive Open Session calls IviSwtch_init (with ID Query and Reset set to true) and CloseSession closes the IVI Switch sessions with the call to Close. The niSE session does not make calls to either reset or self-test explicitly.
    Always attempt to perform all the operations on the same piece of hardware using the same API. If you need to reset switches, use the niSE_DisconnectAll function. If you need to perform the self-test operation, open a session to IVI Switch and perform the self-test, and then close it before opening the session to niSE virtual device.
    There is also a back-door possibility that you can obtain the IVI Switch session that has been open for the constituent devices by niSE, but you must make sure that whatever you do with that session leaves the state of the switch intact when you get back to making calls to the niSE session. If unsure, you can always call niSE_DisconnectAll() as the first thing coming back to the niSE session to ensure that the state stored in niSE session matches the state on the actual hardware.
    Again, it is best not to use both sessions, but rather pick one and try to perform all operations with it before switching to another type of session.
    Srdan Zirojevic

  • How to switch off Beats audio to type the latter "B"

    Hi Guys I've got a problem with Beats audio or keyboard, is anybody come cross when try to type a latter "B" pops up Beats audio and can't switch of it, so cant not type latter "B" at all, any ideas? many thanks 

    The keyboard shortcut for Beats is fn+b. It toggles it on and off. Other than that, you can pull it up from the start menu to turn it off.

  • Quicktime doesn't switch to external audio

    Hey guys,
    The problem I have is with QuicktimeX on ML is it not sending any audio to my external soundcard and my external speakers. If I turn my soundcard ON then iTunes, Safari, etc. will all play audio to my external speakers (switching over properly even). Quicktime only will send audio out if 'internal speakers' are selected in the audio section of system perfs.

    If you can't solve your issue and no one in the community can help, contact support to speak with a tech support agent at (800) 457-7777.
    - Peter

  • Is Auto Switch to HDMI Audio Possible?

    I have a dv5-1235dx laptop and use vista, and finally figured out how to get the hdmi sound to work after searching this board and other sites (by manually choosing hdmi as default playback device), but it appears this requires a manual switch every time the hdmi cable is plugged in.  Have updated all drivers etc. (intel high definition hdmi), but still requires manual switch when I want to watch something on my hdtv.  Is there any other driver or solution that would just switch over to hdmi audio automatically when plugged in?  Seems like this is a common issue, and one that ought to be fairly easy to resolve, but i'm  not really that tech savvy so maybe it's more complicated and just an HP/intel issue that can't be resolved?  Anybody have any workarounds for this?

    First of all, its not a Intel/HP issue and your playback device will automatically be set to speakers once you disconnect your HDMI cable.and be automatically set to HDMI once you connect your HDMI cable to the laptop.
    Its similar to how you connect your headphone to headphone jack on the laptop. Make sure setting - HDMI as default playback device has been done when you have disconnected your HDMI cable from the laptop and not when its connected to the laptop.
    In order to do,
    Go to Control Panel\Hardware and Sound and click on sound . On playback tab, right click on white (blank) area and you would see 2 options (Show disabled Devices and Show Disconnected Devices). Make sure both options are checked to have all playback devices listed. 
    Now right click on HDMI ouput device option and ensure "Set as default device" option is checked to hear audio from external display while playing picture on external display.
    //Click on Kudos and Accept as Solution if my reply was helpful and answered your question//
    I am an HP employee!!

  • Switching on external audio ejects external hard drives

    Hi folks. Weird problem here.
    I have an iMac (27-inch, Late 2012, 2.9 GHz Intel Core i5, 32 GB 1600 MHz DDR3) with a regular 3.5mm line-out jack going from the audio out port to an external speaker/subwoofer system.
    Whenever my mac is on and I have forgotten to power up the external speakers, once I flick the switch on the system all the external Hard Drives attached to my mac eject (750GB WD USB2, 4TB Seagate USB3, 5TB Seagate USB3).
    Normally they reappear after a minute or so but sometimes they don't and I have to restart in order to have them show up.
    I am beginning to think that it is related to an issue I have had ongoing for a number of months (since upgrading to Yosemite actually) 27" iMac randomly reboots whereby I would have messages appearing throughout the day saying "external Disks have not been ejected properly", and then having 2 HD's terminally fail on me.
    I have seen other threads talking about glitches with their audio when using audio in/out devices but I have seen nothing about hard- drives being ejected.
    I suspect that the Headphone/optical digital audio output (minijack) is susceptible to power surges, such as a connected device being switched on and this somehow causes the ejection.
    Anyone else have similar problems or know of a possible cause?

    Hi folks. Weird problem here.
    I have an iMac (27-inch, Late 2012, 2.9 GHz Intel Core i5, 32 GB 1600 MHz DDR3) with a regular 3.5mm line-out jack going from the audio out port to an external speaker/subwoofer system.
    Whenever my mac is on and I have forgotten to power up the external speakers, once I flick the switch on the system all the external Hard Drives attached to my mac eject (750GB WD USB2, 4TB Seagate USB3, 5TB Seagate USB3).
    Normally they reappear after a minute or so but sometimes they don't and I have to restart in order to have them show up.
    I am beginning to think that it is related to an issue I have had ongoing for a number of months (since upgrading to Yosemite actually) 27" iMac randomly reboots whereby I would have messages appearing throughout the day saying "external Disks have not been ejected properly", and then having 2 HD's terminally fail on me.
    I have seen other threads talking about glitches with their audio when using audio in/out devices but I have seen nothing about hard- drives being ejected.
    I suspect that the Headphone/optical digital audio output (minijack) is susceptible to power surges, such as a connected device being switched on and this somehow causes the ejection.
    Anyone else have similar problems or know of a possible cause?

  • I now need sound switch up for audio to play out

    I Alway use my iPad to watch tv and until yesterday it didn't need to have the sound switch unmuted. Why do I now need to have sound active for the sound to play on a video?

    Hello bkarschnick,
    Thanks for contacting Apple Support Communities.
    Your computer may not supply audio via the Mini DisplayPort. Take a look at this article for your compute and find out if it supplies  audio.
    About Mini DisplayPort to HDMI adapters
    http://support.apple.com/kb/HT4241
    If your computer is on the list that should supply audio and video, then take a look at this to adjust your sound output.
    OS X Mavericks: Adjust your computer’s sound output
    http://support.apple.com/kb/PH13908
    Regards,
    Jeff D.

  • Audio mutes when switching modes in Audio Cons

    I have an Xfi Platinum that is working great except one annoying problem. Ever since I upgraded the drivers to the latest version, everytime I switch audio modes, for example from game to entertainment, the sound mutes on my system. I have to open the Windows XP sound control to uncheck mute every time. Has anybody experienced this problem and have a fix for it's I downloaded the mode switching program from a link on this forum, but it does the same thing. Thank you!

    Don't know if this will help...  Try changing the multi-track preview/playback settings (press F4)...  If the playback buffer is too big or too small you may get dropouts...
    Also try to defrag the hard drive with virtual memory turned off.  With VM off it may run slow, but it should defrag the swap file as well making your drive super optimized. You may have to boot in safe mode to make it work though...  Of course you can turn the VM back on when you're done...
    Clean out the dust from the computer and make sure it isn't over heating...???

  • How can I switch my output audio from stereo to mono?

    Hey,
    I can only hear out of one ear and I would like to be able to listen to the other half of my music on my headphones, how can I switch my audio from stereo to mono?
    Thanks!
    Zach

    http://www.radioshack.com/product/index.jsp?productId=2102690
    http://www.scansound.com/index.php/stereo-to-mono-adapter.html
    Or you could buy a mono/one ear headset. http://www.beso.com/2699431644/detail

Maybe you are looking for