Multicast and SCCM2012 and Hash error

Ok, so I've searched this time through articles and they all pertain to 2007 - When trying to deploy an OS, Multicast is turned on, but I get the dreaded hash error. If I turn multicast off, It works fine... not a logical solution. I have verified
with network that the switches all have multicast turned on. I've deleted the image, re-added it and redeployed it countless times. Still same issue. The size of the image is 3.06 mb, so well under the 4mb issues that were in 2007.
I've also gone as far as recreating the image from scratch, and still no luck.
Any ideas? This is 2012 SCCM.
Thanks!

That's what I meant, SMSTS.LOG - Here's what most of the log says:
Verifying MCS certificate using default Hash Algorithm: 0x8004 ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Initializing HTTP transport. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting URL = OPTIMUS.psdschools.org. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting Default Ports = 80 443 ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting CRL = false. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting Media Certificate. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting Authenticator. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Set authenticator in transport ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Preparing Multicast Session Request. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting transport. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting site code = SSC. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting client ID = {9C044138-650C-47F1-9AAE-150D809881BD}. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting remote path = http://OPTIMUS.psdschools.org/SMS_DP_SMSPKG$/SSC0003B. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting packageID = SSC0003B. ApplyOperatingSystem 7/11/2012 3:46:54 PM 1880 (0x0758)
Setting server signing Certificate. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Executing Open Session Request. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Sending RequestMulticast ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Setting message signatures. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Setting the authenticator. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
CLibSMSMessageWinHttpTransport::Send: URL: OPTIMUS.psdschools.org:80 CCM_POST /SMS_MCS/.sms_mcs?op=opensession ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Request was succesful. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Default CSP is Microsoft Enhanced RSA and AES Cryptographic Provider ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Default CSP Type is 24 ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
MCSErrorCode = 0 ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
ResponseSessionOpen/SessionAction = 1 ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
ResponseSessionOpen/DPName = OPTIMUS ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
ResponseSessionOpen/Namespace = http://OPTIMUS.psdschools.org/SMS_DP_SMSPKG$/SSC0003B ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
ResponseSessionOpen/SessionStartTime = 0 ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
ResponseSessionOpen/MinimumSessionSize = 0 ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
not decoding EncryptionKey in ssl mode ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Successfully parsed MCS response. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Found multicast service point 'OPTIMUS.psdschools.org' to serve request. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
MCS open session request completed successfully ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Using MCSServer: OPTIMUS ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Using Namespace: http://OPTIMUS.psdschools.org/SMS_DP_SMSPKG$/SSC0003B ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Using Encryption: FALSE ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Session Start Time Delay:0 ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Using LocalPath: D:\_SMSTaskSequence\Packages\SSC0003B ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Opening firewall for X:\sms\bin\x64\OSDApplyOS.exe ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Download: Server=OPTIMUS Namespace=http://OPTIMUS.psdschools.org/SMS_DP_SMSPKG$/SSC0003B RemoteObject=http://OPTIMUS.psdschools.org/SMS_DP_SMSPKG$/SSC0003B LocalObject=D:\_SMSTaskSequence\Packages\SSC0003B.{756A6CCE-5696-45A5-87D6-827682FCE3FE} ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Checking volume for sparse files: D:\ ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Volume supports sparse files: TRUE ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
[SparseFile] ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Token before WdsTransportClientStartSession ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Token is for User: NT AUTHORITY\SYSTEM ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
ThreadId: 0x758 User: NT AUTHORITY\SYSTEM ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
[Callback:SessionComplete:0x2] ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
WdsTransportClientStartSession(m_hDownload), HRESULT=80070002 (e:\nts_sccm_release\sms\server\mcs\consumer\mcdownload.cpp,182) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
pDownload->Download(pwszServer, pwszNamespace, pwszRemoteObject, pwszLocalObject, uCacheSize), HRESULT=80070002 (e:\nts_sccm_release\sms\server\mcs\consumer\mcclient.cpp,120) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Encountered error transfering file (0x80070002). ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Sending status message: SMS_OSDeployment_PackageDownloadMulticastStatusFail ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Setting authenticator. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Set authenticator in transport ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Sending StatusMessage ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Setting message signatures. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Setting the authenticator. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
CLibSMSMessageWinHttpTransport::Send: URL: OPTIMUS.psdschools.org:80 CCM_POST /ccm_system/request ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Request was succesful. ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Download done setting progress bar to 100 ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Succesfully performed multicast download from mcs://OPTIMUS.psdschools.org/SMS_MCS/.sms_mcs?filePath=http://OPTIMUS.psdschools.org/SMS_DP_SMSPKG$/SSC0003B&PackageFlags=1241514144&packageID=SSC0003B&version=8 ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
VerifyContentHash: Hash algorithm is 32780 ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Hash could not be matched for the downloded content. Original ContentHash = 51DE9114123FC1EA9F6638CCED3271AA856F255CDF8BFF6B4C3841D5FD7340AB, Downloaded ContentHash = ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
0L == TS::Utility::VerifyPackageHash(pszContentID, sDestination), HRESULT=80091007 (e:\nts_sccm_release\sms\framework\tscore\resolvesource.cpp,2900) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
DownloadContentAndVerifyHash(pszPackageID, L"SMSPackage", saHttpContentSources, saSMBContentSources, saMulticastContentSources, sDestination, dwFlags, L"", 0, dwPackageFlags, pszUserName, pszUserPassword ), HRESULT=80091007 (e:\nts_sccm_release\sms\framework\tscore\resolvesource.cpp,3007) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
DownloadContentLocally(pszSource, sSourceDirectory, dwFlags, hUserToken, pszUserName, pszUserPassword), HRESULT=80091007 (e:\nts_sccm_release\sms\framework\tscore\resolvesource.cpp,3217) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
ResolveSource(pszSource, sSourceDirectory, dwFlags, 0, 0, 0), HRESULT=80091007 (e:\nts_sccm_release\sms\framework\tscore\resolvesource.cpp,3122) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
TS::Utility::ResolveSource( this->packageID, this->packagePath, TS::Utility::ResolveSourceFlags::PersistContents ), HRESULT=80091007 (e:\nts_sccm_release\sms\client\osdeployment\applyos\installimage.cpp,1368) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
resolvePkgSource(), HRESULT=80091007 (e:\nts_sccm_release\sms\client\osdeployment\applyos\installimage.cpp,1411) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Apply(), HRESULT=80091007 (e:\nts_sccm_release\sms\client\osdeployment\applyos\installimage.cpp,1614) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Installation of image 1 in package SSC0003B failed to complete..
The hash value is not correct. (Error: 80091007; Source: Windows) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
installer.install(), HRESULT=80091007 (e:\nts_sccm_release\sms\client\osdeployment\applyos\installimage.cpp,1689) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Entering ReleaseSource() for D:\_SMSTaskSequence\Packages\SSC0003B ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
The user tries to release a source directory D:\_SMSTaskSequence\Packages\SSC0003B that is either already released or we have not connected to it ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
InstallImage( g_InstallPackageID, g_ImageIndex, targetVolume, ImageType_OS, g_ConfigPackageID, g_ConfigFileName, bOEMMedia ), HRESULT=80091007 (e:\nts_sccm_release\sms\client\osdeployment\applyos\applyos.cpp,470) ApplyOperatingSystem 7/11/2012 3:46:55 PM 1880 (0x0758)
Process completed with exit code 2148077575 TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
!--------------------------------------------------------------------------------------------! TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Failed to run the action: Apply Operating System.
The hash value is not correct. (Error: 80091007; Source: Windows) TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
MP server http://OPTIMUS.psdschools.org. Ports 80,443. CRL=false. TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Setting authenticator TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Set authenticator in transport TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Sending StatusMessage TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Setting message signatures. TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Setting the authenticator. TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
CLibSMSMessageWinHttpTransport::Send: URL: OPTIMUS.psdschools.org:80 CCM_POST /ccm_system/request TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Request was succesful. TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Set a global environment variable _SMSTSLastActionRetCode=-2146889721 TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Set a global environment variable _SMSTSLastActionSucceeded=false TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Clear local default environment TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Let the parent group (Install Operating System) decides whether to continue execution TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
The execution of the group (Install Operating System) has failed and the execution has been aborted. An action failed.
Operation aborted (Error: 80004004; Source: Windows) TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Failed to run the last action: Apply Operating System. Execution of task sequence failed.
The hash value is not correct. (Error: 80091007; Source: Windows) TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
MP server http://OPTIMUS.psdschools.org. Ports 80,443. CRL=false. TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Setting authenticator TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Set authenticator in transport TSManager 7/11/2012 3:46:55 PM 1124 (0x0464)
Sending StatusMessage TSManager 7/11/2012 3:46:56 PM 1124 (0x0464)
Setting message signatures. TSManager 7/11/2012 3:46:56 PM 1124 (0x0464)
Setting the authenticator. TSManager 7/11/2012 3:46:56 PM 1124 (0x0464)
CLibSMSMessageWinHttpTransport::Send: URL: OPTIMUS.psdschools.org:80 CCM_POST /ccm_system/request TSManager 7/11/2012 3:46:56 PM 1124 (0x0464)
Request was succesful. TSManager 7/11/2012 3:46:56 PM 1124 (0x0464)
Executing command line: X:\WINDOWS\system32\cmd.exe /k TSBootShell 7/11/2012 3:47:00 PM 808 (0x0328)
The command completed successfully. TSBootShell 7/11/2012 3:47:00 PM 808 (0x0328)
Successfully launched command shell. TSBootShell 7/11/2012 3:47:00 PM 808 (0x0328)

Similar Messages

I have to send messages through UDP multicast and unicast from same port. In Labview I tried that it throws error. I heard it is possible by means of Datagram (UDP unicast and multicast) Port Sharing. How can it be achieved in Labview?

I have to send UDP multicast and Unicast messages to a remote port from a single source/local port. I tried by opening UDP unicast and multicast in the same port and got the expected error. I tried by opening a unicast connection and sending unicast messages.After that when multicast messages has to send I closed unicast and opened multicast in the same port.This is not throwing any error. But my requirenment is to comminicate with another application in C ++ which recieves this data, throwing an error of lost connectivity and both the applications are not abled to communicate properly.
In the other application with C++ this is implemented using port sharing. So how port sharing can be implemented in labview so that I can send both multicast and unicast messages from the same port?
Thanks in advance

UDP is a sessionless protocol, meaning that anyone listening on the specified port CAN receive the data. CAN because as you noted there is no guarantee in the protocol that it will be received. And if you send the data not to a specific address but a multicast address not only one computer can receive it but in fact every computer on the same subnet listening to that multicast address and depending on the TTL of the packet also computers in neighbouring subnets, although that last one is not a very reliable operation since routers can be configured to drop multicast packages anyhow despite of a different TTL saying otherwise.
Accordingly there is no real way to make sure that a receiving UDP port is not already in use, since you don't build up a connection. UDP is more or less analogous to shouting your messages through a megaphone, and anyone listening on the right frequency (port) can hear it. You do bind the sender socket to a specific port number but that makes little difference.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

Creation of Sorted and Standard and Hashed Internal Tables ..

Hi ..
Pls specify me.. how to create .. sorted ,Standard and Hashed Internal Tables...
pls give me the full code regarding ...this ..
Thnks

Standard tables
This is the most appropriate type if you are going to address the individual table entries using the index. Index access is the quickest possible access. You should fill a standard table by appending lines (ABAP APPEND statement), and read, modify and delete entries by specifying the index (INDEX option with the relevant ABAP command). The access time for a standard table increases in a linear relationship with the number of table entries. If you need key access, standard tables are particularly useful if you can fill and process the table in separate steps. For example, you could fill the table by appending entries, and then sort it. If you use the binary search option with key access, the response time is logarithmically proportional to the number of table entries.
Sorted tables
This is the most appropriate type if you need a table which is sorted as you fill it. You fill sorted tables using the INSERT statement. Entries are inserted according to the sort sequence defined through the table key. Any illegal entries are recognized as soon as you try to add them to the table. The response time for key access is logarithmically proportional to the number of table entries, since the system always uses a binary search. Sorted tables are particularly useful for partially sequential processing in a LOOP if you specify the beginning of the table key in the WHERE condition.
Hashed tables
This is the most appropriate type for any table where the main operation is key access. You cannot access a hashed table using its index. The response time for key access remains constant, regardless of the number of table entries. Like database tables, hashed tables always have a unique key. Hashed tables are useful if you want to construct and use an internal table which resembles a database table or for processing large amounts of data.
Special Features of Standard Tables
Unlike sorted tables, hashed tables, and key access to internal tables, which were only introduced in Release 4.0, standard tables already existed several releases previously. Defining a line type, table type, and tables without a header line have only been possible since Release 3.0. For this reason, there are certain features of standard tables that still exist for compatibility reasons.
Standard Tables Before Release 3.0
Before Release 3.0, internal tables all had header lines and a flat-structured line type. There were no independent table types. You could only create a table object using the OCCURS addition in the DATA statement, followed by a declaration of a flat structure:
DATA: BEGIN OF <itab> OCCURS <n>,
<fi> ...
END OF <itab>.
This statement declared an internal table <itab> with the line type defined following the OCCURS addition. Furthermore, all internal tables had header lines.
The number <n> in the OCCURS addition had the same meaning as in the INITIAL SIZE addition from Release 4.0. Entering 0 had the same effect as omitting the INITIAL SIZE addition. In this case, the initial size of the table is determined by the system.
The above statement is still possible in Release 4.0, and has roughly the same function as the following statements:
TYPES: BEGIN OF <itab>,
<fi> ...,
END OF <itab>.
DATA <itab> TYPE STANDARD TABLE OF <itab>
WITH NON-UNIQUE DEFAULT KEY
INITIAL SIZE <n>
WITH HEADER LINE.
In the original statement, no independent data type <itab> is created. Instead, the line type only exists as an attribute of the data object <itab>.
Standard Tables From Release 3.0
Since Release 3.0, it has been possible to create table types using
TYPES <t> TYPE|LIKE <linetype> OCCURS <n>.
and table objects using
DATA <itab> TYPE|LIKE <linetype> OCCURS <n> WITH HEADER LINE.
The effect of the OCCURS addition is to construct a standard table with the data type <linetype>. The line type can be any data type. The number <n> in the OCCURS addition has the same meaning as before Release 3.0. Before Release 4.0, the key of an internal table was always the default key, that is, all non-numeric fields that were not themselves internal tables.
The above statements are still possible in Release 4.0, and have the same function as the following statements:
TYPES|DATA <itab> TYPE|LIKE STANDARD TABLE OF <linetype>
WITH NON-UNIQUE DEFAULT KEY
INITIAL SIZE <n>
WITH HEADER LINE.
They can also be replaced by the following statements:
Standard Tables From Release 4.0
When you create a standard table, you can use the following forms of the TYPES and DATA statements. The addition INITIAL SIZE is also possible in all of the statements. The addition WITH HEADER LINE is possible in the DATA statement.
Standard Table Types
Generic Standard Table Type:
TYPES <itab> TYPE|LIKE STANDARD TABLE OF <linetype>.
The table key is not defined.
Fully-Specified Standard Table Type:
TYPES <itab> TYPE|LIKE STANDARD TABLE OF <linetype>
WITH NON-UNIQUE <key>.
The key of a fully-specified standard table is always non-unique.
Standard Table Objects
Short Forms of the DATA Statement :
DATA <itab> TYPE|LIKE STANDARD TABLE OF <linetype>.
DATA <itab> TYPE|LIKE STANDARD TABLE OF <linetype>
WITH DEFAULT KEY.
Both of these DATA statements are automatically completed by the system as follows:
DATA <itab> TYPE|LIKE STANDARD TABLE OF <linetype>
WITH NON-UNIQUE DEFAULT KEY.
The purpose of the shortened forms of the DATA statement is to keep the declaration of standard tables, which are compatible with internal tables from previous releases, as simple as possible. When you declare a standard table with reference to the above type, the system automatically adopts the default key as the table key.
Fully-Specified Standard Tables:
DATA <itab> TYPE|LIKE STANDARD TABLE OF <linetype>
WITH NON-UNIQUE <key>.
The key of a standard table is always non-unique.
Internal table objects
Internal tables are dynamic variable data objects. Like all variables, you declare them using the DATA statement. You can also declare static internal tables in procedures using the STATICS statement, and static internal tables in classes using the CLASS-DATA statement. This description is restricted to the DATA statement. However, it applies equally to the STATICS and CLASS-DATA statements.
Reference to Declared Internal Table Types
Like all other data objects, you can declare internal table objects using the LIKE or TYPE addition of the DATA statement.
DATA <itab> TYPE <type>|LIKE <obj> WITH HEADER LINE.
Here, the LIKE addition refers to an existing table object in the same program. The TYPE addition can refer to an internal type in the program declared using the TYPES statement, or a table type in the ABAP Dictionary.
You must ensure that you only refer to tables that are fully typed. Referring to generic table types (ANY TABLE, INDEX TABLE) or not specifying the key fully is not allowed (for exceptions, refer to Special Features of Standard Tables).
The optional addition WITH HEADER line declares an extra data object with the same name and line type as the internal table. This data object is known as the header line of the internal table. You use it as a work area when working with the internal table (see Using the Header Line as a Work Area). When you use internal tables with header lines, you must remember that the header line and the body of the table have the same name. If you have an internal table with header line and you want to address the body of the table, you must indicate this by placing brackets after the table name (<itab>[]). Otherwise, ABAP interprets the name as the name of the header line and not of the body of the table. You can avoid this potential confusion by using internal tables without header lines. In particular, internal tables nested in structures or other internal tables must not have a header line, since this can lead to ambiguous expressions.
TYPES VECTOR TYPE SORTED TABLE OF I WITH UNIQUE KEY TABLE LINE.
DATA: ITAB TYPE VECTOR,
JTAB LIKE ITAB WITH HEADER LINE.
MOVE ITAB TO JTAB. <- Syntax error!
MOVE ITAB TO JTAB[].
The table object ITAB is created with reference to the table type VECTOR. The table object JTAB has the same data type as ITAB. JTAB also has a header line. In the first MOVE statement, JTAB addresses the header line. Since this has the data type I, and the table type of ITAB cannot be converted into an elementary type, the MOVE statement causes a syntax error. The second MOVE statement is correct, since both operands are table objects.
plz reward if useful

CRC errors and input errors on Te 1/2 of Cisco WS-C3560X-48 switch

Hi All,
I am observing CRC errors and input errors on one of the Te1/2 interface of WS-C3560X-48 Cisco switch. I have not observed any CRC errors or input errors on the connected interface at other end. Can you please let us know whether the issue is with cable or SFP module.
Effected interface:
TenGigabitEthernet1/2 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet, address is f866.f243.e6b6 (bia f866.f243.e6b6)
Description: *** MAN-SW1B***
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 254/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 3w5d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 29000 bits/sec, 30 packets/sec
5 minute output rate 45000 bits/sec, 37 packets/sec
68905128 packets input, 8272036576 bytes, 0 no buffer
Received 68904979 broadcasts (68812046 multicasts)
0 runts, 0 giants, 0 throttles
146170 input errors, 130065 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 68812046 multicast, 0 pause input
0 input packets with dribble condition detected
83524620 packets output, 12642123488 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Other end.
TenGigabitEthernet1/4 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet Port, address is 503d.e53b.9703 (bia 503d.e53 b.9703)
Description: *** DMZ-SW1B ***
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s, link type is auto, media type is 10GBase-SR
input flow-control is on, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 32000 bits/sec, 27 packets/sec
5 minute output rate 21000 bits/sec, 22 packets/sec
918379921 packets input, 312586470396 bytes, 0 no buffer
Received 881142868 broadcasts (875016400 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
463132111 packets output, 240865283601 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out

When there are more than two members in a cluster (stack), the Gigabit interface operates at half-duplex. Since collisions can result at half-duplex, some CRCs errors are normal.

CRC Error and input Error how can fix these

FastEthernet0/13 is up, line protocol is up
Hardware is Fast Ethernet, address is 0004.4d27.66cd (bia 0004.4d27.66cd)
Description: EDL-P-Box-NO-4
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 250/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex (Full), Auto Speed (100), 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 18:52:43, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 12000 bits/sec, 6 packets/sec
5 minute output rate 24000 bits/sec, 6 packets/sec
     14488019 packets input, 2783320210 bytes
     Received 345346 broadcasts, 0 runts, 0 giants, 0 throttles
     261028 input errors, 259429 CRC, 1599 frame, 0 overrun, 0 ignored
     0 watchdog, 84207 multicast
     0 input packets with dribble condition detected
     19658279 packets output, 3529106068 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
PAD-8-1-10.179#cle
v

Hi,
Check out the below explanation for CRC error and farme error and few useful links to trouble shoot these type of problems
The CRC error rate is 1.75915% (greater than 1 in a million packets),
and the collision rate is less than 0.1%.
This can indicate excessive noise or transmission problems on the LAN or the LAN
bus itself. A high number of CRCs is usually the result of collisions or a station
transmitting bad data.
TRY THIS: Check cables to determine whether any are damaged. If 100BaseTX is being
used, ensure Category 5 cabling is being used and not another type, such as Category
3.
There have been 1599 'frame errors' reported.
This indicates the number of packets received incorrectly, having a CRC error
and a non-integer number of octets. On a LAN, this is usually the result of collisions
or a malfunctioning Ethernet device.
TRY THIS: Monitor the level of frame errors over time. If they are increasing,
try swapping interfaces and or ports to identify the problem.
http://www.cisco.com/en/US/customer/products/hw/modules/ps2033/products_tech_note09186a008009446d.shtml
http://www.cisco.com/en/US/docs/internetworking/troubleshooting/guide/tr1904.html
http://www.cisco.com/en/US/docs/internetworking/troubleshooting/guide/tr1904.html
Hope that helps out your query !!
Regards
Ganesh.H

Sorted and hashed tables

what happens when duplicate entries are present in sorted and hashed tables?

Hi,
Sorted internal tables can be of two types:
unique or non unique.
If u enter duplicate records in Sorted tables with unique it will show error.
If u enter duplicate records in Sorted tables with non-unique key it will not show error.
Hashed tables are with only unique key
so no way to enter the duplicate records.
for more information see the following link
http://help.sap.com/saphelp_nw70/helpdata/en/fc/eb35de358411d1829f0000e829fbfe/content.htm
Reward if helpful.
Jagadish

Each time I try to synch photos from my Windows 7 PC to my iPad2, iTunes stops working, and the error report says Problem Event Name:     APPCRASH   Application Name:     iTunes.exe   Application Version:     10.3.1.55   Application Timestamp:     4deec35

Each time I try to synch photos from my Windows7 PC to my iPad2, iTunes stops working and the error message is:
Problem Event Name:                          APPCRASH
Application Name:                             iTunes.exe
Application Version:                           10.3.1.55
Application Timestamp:                    4deec351
Fault Module Name:                          ntdll.dll
Fault Module Version:                        6.1.7601.17514
Fault Module Timestamp:                 4ce7ba58
Exception Code:                                  c0000005
Exception Offset:                                0002e3fb
OS Version:                                          6.1.7601.2.1.0.768.3
Locale ID:                                             1033
Additional Information 1:                  0a9e
Additional Information 2:                  0a9e372d3b4ad19135b953a78882e789
Additional Information 3:                  0a9e
Additional Information 4:                  0a9e372d3b4ad19135b953a78882e789
I reloaded iTunes 10 (64 bit) successfully, but the problem remains the same.
Any suggestions?

I looked in the folder from which I want to synch photos, but there is no such thing as an "ipod photo cache" in that folder, or sub-folders, as suggested in the link which you were nice enough to provide.
I have also tried removing photos from my iPad2 Photos App, and "iTunes has stopped working" shows up again as soon as I click on the "Synch photos from" button.

2TB Ext. Hard Drive is corrupted?, error code -50 and then error code -35 when i try to empty out my trash

okay so a few days ago i received and email for one of my colleagues to do some final editing to a music video. the folder contained 2 videos a rough chops and the main which was about 2-3GB which i dragged on to my external hard drive . and at the time i was trying to install a trial version of parallel lines and me being a newbie to the software i didn't know i need windows installments for it to run lol but yeah... so i was just getting frustrated with the software i kept installing it uninstalling it and then i was thinking my the problem might be because my MacHD space is low (less then 40GBs on my MacHD), so.. i installed it on my hard drive where all my important files are (I'm a graphic designer and do light video editing) video projects and many photoshop projects form 2007 and logs and just a bunch of important files in my hard drive. so because i was so frustrated with the software i wasn't thinking and i installed it on my external 2TB hard drive. and when i realized parallel wasn't working i gave up, uninstalled the program form the hard drive and for some reason when i did that and i tried opening the video my friend had email to me and for some reason it did load up but a few seconds maybe about 10sec in the video is froze and closed my media app (VLC) and when i tried opening other video files it would freeze every few minutes but those specific files i had drag in last were not playing after at least 5 secs and eventually didn't open at all so i restart my computer login and now i get scared i see that my MacBook Pro isn't reading my external hard drive so i search threw forums... i unplug from the wall plug my external hard drive back in my computer and it loaded up but when i opened my external hard drive all my files had that plank white paper icon on my folders (because i have everything organized but subject when you open then drive folder. so... i go in to my projects and nothing, i open my edited photos and nothing... my hart feels like its about to drop and i keep opening files and there is nothing in them, but in "get info" of my drive it shows that there is filled so i go to "disk utility"... i "verify disk" passes ..."repair disk" doesn't past.... i look it up in forums... so i reboot my computer and go to the safe recovery menu. go threw the same ting "disk utility"... verify, pass... repair, pass... so now i feel relieved. i login files in the ext. hard drive load up i tried again to open the files and same thing happens... so now I'm thinking its the files i drag the files to the trash and try to empty and its gone i reboot the computer and my drive didn't load up so i tried unplugin it and back in... drive comes up i notice theres trash.. i tried emptying it and i get the error code -50. and no files are popping up on my external drive and i try to repair/unmount disk and the verify disk doesn't pass and when i click repair disk it doesn't past and another error code pops up -35.... so i felt my drive alone for a few days and yesterday i go the files deleted from the trash and now I'm not getting any codes but when i try to unmount.verify/repair the disk. keeps letting my tits need to be repaired so i click the repair button another error unable to unmount volume to repair...
what do i do? my files still don't show up. and I'm very sorry for the long paragraph but i have to be detailed for you to understand my situation

Read this.

Sender mail adapter : no messages and no error log

Hello,
I have configured a sender mail adapter to read mails from the inbox. I have used IMAP protocol. URL is specified as imap://EMHBSEXM01/Inbox. User name and password is also specified properly. I have kept poll interval to 1 minute. Messages in the inbox are in unread status. But the mail is not getting processed. I do not see anything after 1 minute. I tried using generate fetch report flag. But even then it does not create any message in SXMB_MONI. I checked runtime workbench for Mail adapter but I do not see any message for the same. Is there something that I am missing?
Thanks,
Dev

Hi All,
I chekced your responses and tried accordingly. Our basis team has given me new link now and the error message has changed. I am getting following error message.
exception caught during processing mail message; java.io.IOException: unexpected login response; read 001F BAD Command received in Invalid state.
Does anyone have any idea what this error is?
Thanks in advance,
Devendra

What is the diffrence between multicasting and broadcasting?

hi friends
What is the diffrence between multicasting and broadcasting?
i'm bit confused in multicasting and broadcasting.

Broadcasts go everywhere within a range determined by the sender.
Broadcasting is deprecated and unliikely to go beyond the nearest router.
Multicasts go everywhere where receivers have declared they are present.
Multicast can be implemented beyond routers in a WAN which you control but ISP routers generally don't support it.

Plug-in errors and dependency errors with a CAF app in DS in NW CE 7.1

I am learining to build CAF apps in Developer Studio in NW CE 7.1. Here are my steps and the errors I am getting:
Open Developer Studio
Switch to the CA perspective
File->New->Project
Choose Development Component under Development Infrastructure
Press Next
Choose Composite Application under sap.com
Choose MyComponents[demo.sap.com] under 'Local Development'
Vendor: demo.sap.com
Name: carpool
Caption: Car Pool
Language: American English
Domain: SAP-xApps
Support Component: CAF-APP (typed in, not chosen)
Press Finish
The following error appears:
Status ERROR
Plugin : com.sap.ide.metamodel.core.services.eclipse
code=0
Internal error
   Plugin name: Metamodel Core
   Internal error : com.sap.ide.metamodel.core.services.eclipse
   Class      : com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker
   Method     : computeIdeJarProperties
   Message    : C:\Program Files\SAP\IDE\CE\eclipse\E:\Program Files\SAP\IDE\CE\eclipse\plugins\com.sap.dictionary.services_10.0.0.070821165456\lib\com.sap.dictionary.services_api.jar (The filename, directory name, or volume label syntax is incorrect)
   Exception : java.io.FileNotFoundException: C:\Program Files\SAP\IDE\CE\eclipse\E:\Program Files\SAP\IDE\CE\eclipse\plugins\com.sap.dictionary.services_10.0.0.070821165456\lib\com.sap.dictionary.services_api.jar (The filename, directory name, or volume label syntax is incorrect)
java.io.FileNotFoundException: C:\Program Files\SAP\IDE\CE\eclipse\E:\Program Files\SAP\IDE\CE\eclipse\plugins\com.sap.dictionary.services_10.0.0.070821165456\lib\com.sap.dictionary.services_api.jar (The filename, directory name, or volume label syntax is incorrect)
at java.util.zip.ZipFile.open(Native Method)
at java.util.zip.ZipFile.<init>(ZipFile.java:203)
at java.util.jar.JarFile.<init>(JarFile.java:132)
at java.util.jar.JarFile.<init>(JarFile.java:70)
at com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker.computeIdeJarProperties(ArchiveVersionChecker.java:296)
at com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker.doFullCheck(ArchiveVersionChecker.java:214)
at com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker.checkProject(ArchiveVersionChecker.java:125)
at com.sap.ide.mmservices.core.eclipse.generation.GenerationServiceEclipse.checkArchiveVersions(GenerationServiceEclipse.java:110)
at com.sap.dictionary.tools.generation.eclipse.GenerationBuilder.checkArchiveVersions(GenerationBuilder.java:335)
at com.sap.dictionary.tools.generation.eclipse.GenerationBuilder.build(GenerationBuilder.java:85)
at org.eclipse.core.internal.events.BuildManager$2.run(BuildManager.java:624)
at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:37)
at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:166)
at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:197)
at org.eclipse.core.internal.events.BuildManager$1.run(BuildManager.java:246)
at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:37)
at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:249)
at org.eclipse.core.internal.events.BuildManager.basicBuildLoop(BuildManager.java:302)
at org.eclipse.core.internal.events.BuildManager.build(BuildManager.java:334)
at org.eclipse.core.internal.events.AutoBuildJob.doBuild(AutoBuildJob.java:137)
at org.eclipse.core.internal.events.AutoBuildJob.run(AutoBuildJob.java:235)
at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55)
I do not think I missed anything installing NW CE 7.1, but this error makes me think that some plug-in was erroneously left out of the install.
Incidentally, I can continue onward and build an app (this is obviously a tutorial), but when I try to deploy I get the following error:
The deployment of the archive failed with an exception!
([ERROR CODE DPL.DCAPI.1027]) DependenciesResolvingException.
Reason:[ERROR CODE DPL.DC.3033] An unresolved dependencies error
occurred while sorting the deployment batch items regarding the
dependencies.;nested exception is:
com.sap.engine.services.dc.cm.deploy.sdu_deps_resolver.UnresolvedDepen
denciesException:[ERROR CODE DPL.DC.3437]Unresolved dependencies
found for the following deployment items:
1. Component: name:'carpool~ear',vendor:'my.company',location:
'localDevelopment',version:'20080501110329',software type: 'J2EE',
dependencies:'[name:'cafruntimeear',vendor:'sap.com',name:
'cafcoreear',vendor:'sap.com']
Unresolved dependency:
name:'cafruntimeear',vendor:'sap.com'          (not found in the admitted
batch items and the repository)
Unresolved dependency:
name:'cafcoreear',vendor:'sap.com'          (not found in the admitted
batch items and the repository)
Please check the error log for further informations.
Again, this looks like I am missing some components.
Any assistance is greatly appreciated.
TB

Further developments: As you may note from the error message, DS is looking for com.sap.ide.metamodel.core.services.eclipse in both the C: and the E: drive at the same time. In fact, this file exists in the E: drive subdirectory listed, so I obviously have an error with two drive designations being concatenated. Does anyone know how I can change the lookup directory for this dependency (or any dependency)?
Thanks,
TB

Input and CRC errors on ASA 5505 outside interface

All,
I see input and crc errors on my ASA 5505 eth0/0(outside) interface and packet drops. There is very slow connection though we have 20mb line. ISP also sees the issue on the Lan interface side. We have the speed and duplex configured same on both ISP and our end.
I am suspecting if this is Physical cable issue. Please suggest.
Hardware is 88E6095, BW 100 Mbps, DLY 100 usec
        Full-Duplex(Full-duplex), 100 Mbps(100 Mbps)
        Input flow control is unsupported, output flow control is unsupported
        Available but not configured via nameif
        MAC address 001a.b4c9.f3d9, MTU not set
        IP address unassigned
        158138067 packets input, 141061681082 bytes, 0 no buffer
        Received 183037 broadcasts, 0 runts, 0 giants
        19642 input errors, 19642 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
        0 pause input, 0 resume input
        0 L2 decode drops
        144684 switch ingress policy drops
        124291353 packets output, 38197278051 bytes, 0 underruns
        0 pause output, 0 resume output
        0 output errors, 0 collisions, 0 interface resets
        0 late collisions, 0 deferred
        0 rate limit drops
        0 switch egress policy drops
        0 input reset drops, 0 output reset drops

Hello Ravi,
This kind of issues CRCs/ Input Errors are tipically known as L1 issues so make sure you check the cable and if that does not make a difference change the port on each side to see if there is a difference.
Unfortunetly the ASA does not support the Time-Domain Reflectometer feature so we must do the test of L1 by ourselfs.
Can you clear the counters of the interface, test the changes provided and provide us some feedback?
Looking for some Networking Assistance?
Contact me directly at [email protected]
I will fix your problem ASAP.
Cheers,
Julio Carvajal Segura
http://laguiadelnetworking.com

Can anyone help me connect my Macbook Air to a SAMSUNG TV. When I follow the basic instructions (Thunderbolt to HDMI connection) the screen on my computer goes grey and an error message appears inviting me to press any button to restart th

Can anyone help me connect my Macbook Air to a SAMSUNG TV. When I follow the basic instructions (Thunderbolt to HDMI connection) the screen on my computer goes grey and an error message appears inviting me to press any button to restart the Macbook. When I do this nothing happens. Only when I disconnect the computer from the TV does the Macbook allow me to login. The TV does not receive any signal from the Macbook even though I know the HDI port works fine. Any ideas what I'm doing wrong? Do I need to enable something on the Macbook?

An update...
I downloaded Apple's (rather large!) list of software updates today, and I was finally able to recognize my iPod again. I did a restore using the iPod updater from 06-2006, and all seemed to work OK. (I'm afraid to try the new one again!)
Then I tried to re-load my music library from iTunes, and got stuck. It froze up after a while and wouldn't go any further.
When I disconnected my iPod from my computer, I find 2 podcasts and nothing else, though iTunes told me it had transferred 600+ songs. Those 2 podcasts do play fine, and the basic iPod software all seems to be intact.
So -- anyone get through this connection problem and have any ideas to share??
iMac Mac OS X (10.4.7)

I have updated my iTunes to the latest edition and now my iTunes wont open saying MSVCR80.dll is missing from my computer and that i have to reinstall itunes. I have tried reinstalling twice now and this error message keeps appearing. What is going on?

I have updated my iTunes to the latest edition and now my iTunes will not open saying MSVCR80.dll is missing from my computer and that i have to reinstall itunes. I have tried reinstalling twice now and this error message keeps appearing. What is going on?

Solving MSVCR80 issue and Windows iTunes install issues.

Time Machine won't back up. Starts of REALLY SLOW, and the errors out.

I've been having a hard time getting time machine to back up. To start off I'll give you my specs and what I have done.
iMac
OS 10.6.6
2.4 GHz Intel Core 2 Duo
4 GB 667 DDR@ SDRAM
320 GB HD
All software updates are current. I am trying to back up to an external Western Digital 1 GB drive connected by USB2. I have formatted the external drive, and set a single partition on that drive from the Disc Utility. I have run disk repair on both the external and local hard drive. I have run disk repair permission on the local drive. I have restarted, after every time. I have done everything listed above multiple times, and have done them all in kinda different orders each time.
My thought is that the issue may not be with the hard drives, but maybe a file its trying to back up. When it starts out for the first time, it tells me that it needs to back up over 100 GB of data. It gets about halfway done, and then errors out. When I try to start it again, it tells me that it needs to backup around 50 GB of data. And this time, its REALLY slow. Like bytes slow, not Mega bytes, or even kilobytes. Bytes. 36 bites backed up, 120 bytes backed up. 2 Kilobytes backed up. SLOW SLOW SLOW.
Then it picks up, and usually gets up to 120 MB, and then gives me this error message "The Backup was not performed because an error occurred while copying files to the backup disk. - The problem may be temporary. Try again later to back up. If the problem persists, use Disk Utility to repair your backup disk."
Its a pretty generic message, and gives me no help in trying to figure out what the problem is. I've been trying again for almost 3 days now, and nothing is working. Is there an error log file that I can go find that would help me a little more?

woody24 wrote:
"The Backup was not performed because an error occurred while copying files to the backup disk. - The problem may be temporary. Try again later to back up. If the problem persists, use Disk Utility to repair your backup disk."
See #C3 in [Time Machine - Troubleshooting|http://web.me.com/pondini/Time_Machine/Troubleshooting.html] (or use the link in *User Tips* at the top of this forum).
Its a pretty generic message, and gives me no help in trying to figure out what the problem is. I've been trying again for almost 3 days now, and nothing is working. Is there an error log file that I can go find that would help me a little more?
Tell Apple about the inadequacy of that message: http://www.apple.com/feedback/timemachine.html

Multicast and SCCM2012 and Hash error

Similar Messages

Maybe you are looking for