Multicast Router Settings

What type of multicat does JMS use? IGMP or EVMRP? I am trying to enable the right one on the routers in my network.
Thanks,
Cindi

Yes, but keep the following in mind:
The Multicast Rate option sets the threshold throughput level a wireless client must obtain in order to be "accepted" by the base station. The lower this value, theoretically, the greater number of clients that can connect, especially those at greater distances from the base station. At the opposite end, the higher this number, only those wireless clients that can achieve the higher throughput value will be able to connect. The multicast rate is not related to what type of equipment you are using. The multicast rate has no effect on the maximum data rate used by the base station. It only affects the lowest rate at which the base station will keep a connection open. The multicast rate is dependent on how much RF noise you have in the area. Remember that increasing the multicast rate causes a decrease in effective range.

Similar Messages

Yoga 2 11 drops signal on Airport router - change router settings?

i have spent several hours with Lenovo tech supports (all perfectly friendly), trying to fix the issue of the Yoga 2 11 consistently dropping the wifi connection at my workplace. Two important considerations:
* It's not entirely on the Yoga, as it does not have this issue with home wifi, coffee shop wifi, etc.
* And several other PC and Mac desktop and laptops have no trouble with the workplace wifi. The problem is definitely the way that the Yoga interacts with the Airport router.
Lenovo tech support has made numerous changes to my drivers, system settings, and so on, but cannot fix the problem. The next solution is to return the Yoga to factory settings -- a solution I'm convinced will not work as I've already returned one laptop to Best Buy for the same problem. In other words, two Yogas, directly out of the box (presumably with factory settings), had this issue.
My question is -- is there possibly a way I can change the Airport router settings (or set up a new network entirely) that might be more compatible with the Yoga 2 11 with Intel Wireless-N 7260 card? If I can't get the Yoga to talk to the router, maybe the router can be changed to talk to the Yoga.

Which model AirPort Base Station do you have?
To determine that open AirPort Utility, select your base station, then position your cursor over the base station's name. Reply with the text shown adjacent to "model".

Airprint no longer working – router settings wrong?

Airprint no longer working – router settings wrong? Network TP-Link TD-W8951ND router. version 5.1, Firmware build 120522. As far as I know the settings are factory defaults with two exceptions. My ISP input various settings to reflect my proper internet connect configuration. I have assigned one static port “100” to a printer not currently on the network. Auto DHCP now starts at “101”. Epson Artisan 837 printer. New, Bonjour service name EPSON3FC9CA (Artisan 837), auto IP address (currently 192.168.1.103), firmware WB15D3 38.38 linked wirelessly not by Ethernet. iPhone 4S Software 6.1.3 (10B329). iPad 3 Software version 6.1.3 (10B329) Windows Vista 32-bit laptop, linked wirelessly, auto IP address Windows 7 64-bit desktop, linked via Ethernet, auto IP address MagicJack Plus, linked via Ethernet, auto IP address Installing Epson On June 6, 2013, using my laptop, installed it wirelessly on my network. Updated firmware etc. All worked well. Same for the desktop. Again all functioning as planned. The installed printer name was Artisan 837 (Network) When I tried to use the Airprint function on my iPhone it could not find any Airprint printers. I downloaded and ran the Bonjour print services wizard. This created a printer named EPSON3FC9CA (Artisan 837). I could now print wirelessly as planned. Problem solved I thought. As of June 6, 2013 all software and firmware is current. On June 12 attempted to link my iPad to Airprint for the first time. It could not find an Airprint printer. I tried my iPhone and it could no longer find an Airprint printer. I tried numerous powerdowns, reboots, reinstalls etc. to no avail. I can point Safari wirelessly to the printer IP address on both iPhone and iPad and see the printer’s “web page” to check ink level, settings etc. I downloaded Epson iPrint to both iPhone and iPad and that software works as planned allowing wireless printing. I tested the Epson on my older Linksys router and my iPad found it as an Airprint printer! Worked wirelessly as planned. Conclusions The only thing that is not working as planned is Airprint functionality on my TP-Link network. I am thinking there is a setting on the TP-Link router that needs to be adjusted to keep the Bonjour established software path open and persistent. From the time I first established the Airprint connection to the next time I tried to establish a connection was some 6 days. Although the iPad and iPhone renew their network lease every 90 days, the other equipment lease runs for 3 days before renewal. I don’t know if the IP address of the Epson changed on renewal. (Even if it did, I would hope the discover functionality should follow to the new address.) Over that 6 day period there were no software or firmware changes. As far as I know the only environmental change would be related to IP addresses or something else at the router level severing the connection. Before trying a static IP setting for the Epson (and I don’t know if that will work) are there any other router settings to check that will clear up this situation? I am sending this to TP-Link, Epson, Apple, and my ISP in hopes that a solution can be found.

Thank you for your reply. What I didn't mention was that I have spent days googling to find an solution. I have tried most alternatives suggested to no avail. My problem is quite technical and most probably has a very specific and simple solution related to my router (set ABC to 123XY). All alternatives ended, "if this doesn't work contact the supplier". So I have - Apple (here), Epson, TP-Link and my ISP. When (if?) I find a solution I'll post it here for others to learn from.

How do I forward a port on my Airport Extreme? I have a Belkin @TV (it's like a sling box), and to watch it over cellular on my iPhone I need to forward the port 49177 in the router settings.

How do I forward a port on my Airport Extreme? I have a Belkin @TV (it's like a sling box), and to watch it over cellular on my iPhone I need to forward the port 49177 in the router settings. A simple set of instructions would be greatly appreciated.

How to Port Forward on AEBS

Verizon Quantum Gateway Router settings issue related to printing and wifi cameras?

Hi,
I have a Verizon Quantum Gateway router and I just did a fresh install of Windows 8.1 Pro x64 and am downloading and installing my printer drivers. I connect the printer to the wifi network, 100% sure it is connected and settings are set to wireless lan. I've had this printer for a while. Doing the setup - it cannot find the printer.
Related: I bought a 2 pack of Motorola Focus66 wifi cameras to watch my dogs when I'm gone. I can connect to the cameras when I'm on my ipad's Verizon Wireless LTE connection, but when I'm at home connected to my same Verizon Fios wifi I cannot view cameras. Yes - the camera and apps support local and remote connections.
I have turned the firewalls all the way off and this does not fix the problems, so I'm believing it is in the router settings. Any suggestions?

I had a wifi network running at my house with a PC, Laptop, 5 iphones an iPad, and an XBox all running with no issues.. I got the "Upgrade" of the Gateway router and I can connect those devices to the network but WiFi printing is screwed up and Air Printing the apple devices is totally dead.. cannot see the printer. The customer support are completely a waste.. they suggested I pay for "Premium Support" At this point I've invested a solid 10-15 hours trying to get this setup and talking to Verizon and its just a mess.

Help required in configuring multicast routing

Hi,
We have two 2 servers and 200 clients.
2 servers are in one vlan, 200 clients are in another vlan.
first server will send data to second server with multicast address 234.5.6.7
second server will send data to 200 clients with multicast address 234.5.6.8
first server is able to send data to second server.
but second server is not able to send data to clients.
If we put clients in same vlan, second server is able to send data to clients.
So we understood that multicast routing needs to be enabled in L3 switch.
Switch Model: 3550
IOS version: 12.1(19)EA1a
Any help in configuration required for this.........
Regards
SKRAO

Hi Skrao,
Does your client vlan and server vlan exist on same layer 3 switch if yes then perform this config and it should work..
On global config mode
ip multicast-routing distributed
On interface vlan config (for both client vlan and server vlan)
ip pim sparse-dense-mode
You can very well fine tune later.Try this and update if it worked.
HTH
Ankur

Multicast routing daemons under Solaris 10 ?

hi all
i'm actually looking for a multicast routing daemon, for solaris 10 x86.
any hint ?
i tried to search for "mrouted", but it seems there's no recent version (last one seems to be for solaris 2.5, and sparc naturlly)
help !
thanks :)
Edited by: Olivier_G on Apr 8, 2009 9:42 AM

nm, i found. my collegs gave me the trick.
quagga + zebra can do it.
i just configured zebra (via quagga), it's like an IOS/Cisco router, and you can setup your comp as a router, and setup static routes, multicast and all.
topic closed :) thanks.

HELP PLEASE ROUTER SETTINGS

Hi, i cannot access my router settings through my browser i know the ip address I'm suppose to go to in my browser but when it asks me for my user i don't know what it is nor my password. I already changed my password on my router do i use that to access my router settings through the internet? i tired to use my router password for the password for the settings but it doesn't work? What am i suppose to but as my dam password and username. When i use my laptop to connect to my router its shows up as EDDIELAN that is what it shows up as when i searched for wifi connections on my laptop. Am i suppose to use EDDIELAN as my user and the password on my router for the password on the setting pagee?
Also currently my router i think has a time when i can use my internet. For example i can't use my internet between 3:30pm and 7:00 pm. How do i disable that crap so i can use my internet anytime i want? Can i control the time i use my internet through the settings? Somebody has set this in my router and i know how have to get rid of it! i want to be able to use my internet when ever i want! help please how do i disable that?

As the password of the router is not working..You have to reset the router for 25-30 seconds and then,try to access the router setup page...Once you reset the router,all the settings on the router will go to factory default...Now,you can configure the router from scratch.

ARD 3.3 slow screen redraw - are there special router settings ?

Hello all !
I think I read somewhere on previous Google searches about special router settings to help ARD run as quickly as possible.
I connect to an external site via an intermediate machine in a DMZ area for security (Network Group stipulation) and have found ARD 3 to be sluggish on a line that has actually been upgraded from 2MBit to 10 MBit ...
I am ARDing from my machine to another also running ARD to then get to the site ...
I also recall version 2 of ARD "seemed" to be better redraw then this version ...
Mitch

So is NO ONE experiencing this?
I find that hard to believe...

Distributed multicast routing command not working on Catalyst 3850 switch

Hi Cisco community,
I was wondering if there is a known problem as to why the ip multicast-routing [distributed] option is not available on the Cat 3850 platforms
global command " ip multicast-routing " is accepted
the configuration guide named:
IP Multicast Routing Configuration Guide, Cisco IOS XE Release 3SE (Catalyst 3850 Switches)
First Published: January 29, 2013
Last Modified: October 22, 2013
explains that this option "key word" [distributed] should be available>
Enables IP multicast routing.
ip multicast-routing [distributed]
Device(config)# ip multicast-routing distributed
=============== Here is what i have and see =========
Config attempt
============
CAT-3850-1(config)#ip multicast-routing distributed
^
Show command:
========
CAT-3850-1#show ip multicast
Multicast Routing: enabled
Multicast Multipath: disabled
Multicast Route limit: No limit
Multicast Fallback group mode: Sparse
Number of multicast boundaries configured with filter-autorp option: 0
Software:
========
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M),
Version 03.03.03SE RELEASE SOFTWARE (fc2)
License rights:
============
CAT-3850-1#sh license right-to-use
Slot# License name Type Count Period left
1 ipservices permanent N/A Lifetime
1 apcount adder 10 Lifetime
License Level on Reboot: ipservices
Slot# License name Type Count Period left
2 ipservices permanent N/A Lifetime
2 apcount adder 10 Lifetime
License Level on Reboot: ipservices
Any hints and help would be greately appreciated.
Many thanks in advance
Markus

Hi Reza,
Thank you for your quick reply, and for putting the record staright. As such, a helpful rating was provided
PS: Feel free to help me one more time if you happend to know folllow on this query :)>
I guess that the disributed function has been included in the standard mulitcast routing command because the key word is no longer needed. Or perhaps this platform does not support this at all.#
Once again , thank you for your help above.
Best regards

SNC Router settings and configuration

Hi All, I wanted to open ports only for Production Server in my SNC Router and not for my Other servers please help me how can I configure SNC Router settings for the same. And also please send me the configuring steps of SNC router from SAP notes PDF. I will be thankful for it.
Regards,
Prashant Chauhan

Hi Rupali,
Thanks for ur reply, I had tried by doing the same settings but it did not worked, below is my current setting of SNC Router, here my SOLMAN Server IP is 192.168.1.135 & my Production Server IP is 192.168.1.84, and when I am using SAP Router string I am able to access all my other servers like Quality, Development or BIW. So I want to restrict those access & want to allow only my Production server. Please help.
P * * *
KT "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 194.39.131.34 *
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.168.1.135 3200
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.168.1.135 3389
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.168.1.135 3200
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.168.1.135 3389
KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 192.168.1.135 3299
#Permission entries to check if the connection is allowed at all
#P sapserv2 194.39.131.34 3200
#P sapserv2 172.168.1.228 3200
#P sapserv2 124.247.200.231 3200
#P * sapserv2 3299
P * 192.168.1.135 3209
P * 192.168.1.135 3299
P * * *

Setting up Multicast Routing for Imaging on HP Switches

I've just spent a bit of time getting multicast imaging to work on our
HP ProCurve switched network so I thought I'd post what was necessary
so if anyone else had to look for it then they'd have some help.
You'll need a switch capable of routing such as a 5300 series that is
already routing regualr IP traffic. By default IGMP routing is disabled
so that multicast traffic will not cross VLANs. Here's how to change
that:
Log into the 5300 in Manager mode (aka Admin)
type "config" /goes into config mode
type "ip multicast routing" /sets up IGMP routing
type "router pim" /sets up Protocol Independant Multicast routing
type "vlan *" /where * is a VLAN numeric ID
type "ip igmp" /sets up IGMP routing on that VLAN
type "ip pim" /sets up PIM routing on that VLAN
Repeat those last three steps for all necessary VLANs
type "exit" /to get back out of config mode - you may have to do
that more than once
type "wri mem" to save the config changes
Then go out to any other switches in the network path for multicasts
and login in Manager mode
type "config"
type "vlan *" /where * is VLAN numeric ID
type "ip igmp" /turns on IGMP routing
Repeat those last two steps for all VLANs that need it
type "exit" /to get back out of config mode - you may have to do
that more than once
type "wri mem" to save the config changes
That's it and it meant I went from "Session Master not found" to "New
Image successful". I hope it helps somebody.
Andrew

On Fri, 22 Sep 2006 18:47:21 GMT, Andrew Ferris wrote:
> I've just spent a bit of time getting multicast imaging to work on our
> HP ProCurve switched network so I thought I'd post what was necessary
> so if anyone else had to look for it then they'd have some help.
Did somebody say coolsolutions?
http://www.novell.com/coolsolutions/...mit_a_tip.html
If you have already compiled drivers or have linux.2 please put them on
http://forge.novell.com/modules/xfmo...ect/?zfdimgdrv
Live BootCd and USB Disk from Mike Charles
http://forge.novell.com/modules/xfmod/project/?imagingx
eZie http://forge.novell.com/modules/xfmod/project/?ezie
Marcus Breiden
If you are asked to email me information please change -- to - in my e-mail
address.
The content of this mail is my private and personal opinion.
http://www.edu-magic.net

Router settings for ITouch

I have been trying to connect my new ITouch with my home wireless, but am having numerous problems. It won't accept the password. I have read some of the discussions, but there are so many things listed there. Right now my router, a WRT54G, is set as WEP with a 64 bit code. From what I have read, I should change it to a 128 bit and generate a key code for that. If I do that, will I need to do something different for my laptops, which have been working fine with the wireless? I don't want to mess things up, as I am not use to dealing with router settings, etc.
Solved!
Go to Solution.

If you change the WEP Encryption from 64-bit to 128-bit,generate the passphrase for you and use KEY 1 to reconnect the wireless network on your laptop.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
Click on the Wireless tab,click on the wireless tab,Set the Wireless channel to 11-2.462GHz,Provide Unique SSID for the Wireless Network Name(not linksys)...and click on save settings.Click on Advanced Wireless Settings,Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now,try to connect the I-Phone and check...

Need to know how to reconfigure router settings

Hi - I was online with tech support for an hour before they told me that they couldn't help me unless I paid them or bought a new router. Neither is an option for me financially so I hope that someone can help. :-(
My cable signal went out very briefly, probably for 5-10 seconds. When it came back, my router was no longer working. I jumped through all the reset hoops that normally work, but nothing worked this time. The tech guy said that I needed to reconfigure my router settings. I don't know how. Can someone here help me?
I am running Windows Vista and the router is a Linksys E1000, version 2. Is there a page on this site that tells me what to do? I couldn't find it.
Thank you SO much for any help that you can give me. I'm desperate!
Solved!
Go to Solution.

Hi! You have to access the setup page of the router to reconfigure the settings. This link should help you: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0ff4c94586a345d082828ec2161aaecf_3686.xml&pid=80&r.... Before doing the steps though, reset your router by pushing the reset button on the device for 15seconds.

Router Settings Help

I'm wondering how I get to my router settings (on the browser, not system preferences).
I've tried entering my IP address into the address bar, but that didn't work.
I'm trying to switch the channel my internet is on, because it's interfering with my phone.
If you don't know what I'm talking about.. it should look something like this >>
http://tinyurl.com/33fsack
I don't know if I can change this "channel" on the airport settings, but any help will be appreciated.

You need to experiment with different channels settings.
AirPort Utility > Manual Setup
Wireless tab/label just below the icons
The Channel setting is on this page. It's probably on Automatic now. Try some manual settings to see if you can find a better channel with less interference.

Multicast Router Settings

Similar Messages

Maybe you are looking for