Multicast via Remotes Access VPN (ASA)
Hi all,
I have an ASA 5505 that I would like to use as a head end device for several customers to RA into so they can access our TEST network. The trouble is that the TEST net provides multicast video streams that my clients need to see. I am currently doing this with a Windows Server and Clients via L2TP. How can I do this with the ASA instead? I know IPSEC doesn't support multicast.....can anything be done?
Hi,
Currently IPSec / Any connect doesn't support multicast over vpn tunnel. As you have now it is possible through L2TP with L2TP client / ASA / Windows Server or if you have IOS router it can be possible through DMVPN/GETVPN....
Regards
Karthik
Similar Messages
-
Hi Guys
I have a problem with a Remote Access VPN on a ASA 5510 8.6.2
I have created a IPSEC Remote Access VPN through the wizard this is pretty much a base install on the ASA without much configuration.
I can connect to the ASA via the Remote Access client and get TX just no RX therefore i cannot access any of the LAN resources
here is a copy of the config any help would be appreciated.
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.252
interface Management0/0
nameif management
security-level 100
ip address 10.2.1.252 255.255.240.0
management-only
ftp mode passive
dns server-group DefaultDNS
domain-name perfectdomain.perfect-image.co.uk
same-security-traffic permit inter-interface
object network Inside-Network
subnet 10.2.0.0 255.255.240.0
description Inside Network
object network NETWORK_OBJ_192.168.1.0_27
subnet 192.168.1.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object-group network LOCAL_NETWORKS_VPN
access-list inside_access_in extended permit ip object NETWORK_OBJ_192.168.1.0_24 any
access-list outside_access_in extended permit ip object NETWORK_OBJ_192.168.1.0_24 object Inside-Network
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool RAIPSECPOOL 192.168.1.1-192.168.1.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside,outside) source static Inside-Network Inside-Network destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static Inside-Network Inside-Network no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable 4430
http 10.2.0.0 255.255.240.0 management
http 10.2.0.0 255.255.240.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet 10.2.0.0 255.255.240.0 inside
telnet timeout 5
ssh 10.2.0.0 255.255.240.0 management
ssh 10.2.0.0 255.255.240.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 10
console timeout 0
dhcpd address 10.2.1.253-10.2.2.252 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RAIPSECTUNNEL internal
group-policy RAIPSECTUNNEL attributes
dns-server value 10.2.1.7 10.2.1.8
vpn-tunnel-protocol ikev1
default-domain value perfectdomain.perfect-image.co.uk
username KI-Admin password OMa9XVzN1OQ0Is.6 encrypted privilege 15
username PI-Admin password BEGl74DXS9pqUL6v encrypted privilege 15
tunnel-group RAIPSECTUNNEL type remote-access
tunnel-group RAIPSECTUNNEL general-attributes
address-pool RAIPSECPOOL
default-group-policy RAIPSECTUNNEL
tunnel-group RAIPSECTUNNEL ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:43c49a676e839e7821ff1473ddeaf90d
: end
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.252
interface Management0/0
nameif management
security-level 100
ip address 10.2.1.252 255.255.240.0
management-only
ftp mode passive
dns server-group DefaultDNS
domain-name perfectdomain.perfect-image.co.uk
same-security-traffic permit inter-interface
object network Inside-Network
subnet 10.2.0.0 255.255.240.0
description Inside Network
object network NETWORK_OBJ_192.168.1.0_27
subnet 192.168.1.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object-group network LOCAL_NETWORKS_VPN
access-list inside_access_in extended permit ip object NETWORK_OBJ_192.168.1.0_24 any
access-list outside_access_in extended permit ip object NETWORK_OBJ_192.168.1.0_24 object Inside-Network
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool RAIPSECPOOL 192.168.1.1-192.168.1.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside,outside) source static Inside-Network Inside-Network destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static Inside-Network Inside-Network no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable 4430
http 10.2.0.0 255.255.240.0 management
http 10.2.0.0 255.255.240.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet 10.2.0.0 255.255.240.0 inside
telnet timeout 5
ssh 10.2.0.0 255.255.240.0 management
ssh 10.2.0.0 255.255.240.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 10
console timeout 0
dhcpd address 10.2.1.253-10.2.2.252 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RAIPSECTUNNEL internal
group-policy RAIPSECTUNNEL attributes
dns-server value 10.2.1.7 10.2.1.8
vpn-tunnel-protocol ikev1
default-domain value perfectdomain.perfect-image.co.uk
username KI-Admin password OMa9XVzN1OQ0Is.6 encrypted privilege 15
username PI-Admin password BEGl74DXS9pqUL6v encrypted privilege 15
tunnel-group RAIPSECTUNNEL type remote-access
tunnel-group RAIPSECTUNNEL general-attributes
address-pool RAIPSECPOOL
default-group-policy RAIPSECTUNNEL
tunnel-group RAIPSECTUNNEL ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:43c49a676e839e7821ff1473ddeaf90d
: endHi Jouni
Still not working I am afraid, here is the current running config, I have noticed when I connect via VPN client the default gateway address on the VPN client is 192.168.1.2 ?? anymore help would be appreciated
thank you
hostname PIFW01
domain-name perfectdomain.perfect-image.co.uk
enable password pBWHd.sDdzPIDYW/ encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface GigabitEthernet0/0
nameif inside
security-level 100
ip address 10.2.1.251 255.255.255.0
interface GigabitEthernet0/1
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
nameif outside
security-level 0
ip address 212.135.154.130 255.255.255.252
interface Management0/0
nameif management
security-level 100
ip address 10.2.1.252 255.255.240.0
management-only
ftp mode passive
dns server-group DefaultDNS
domain-name perfectdomain.perfect-image.co.uk
same-security-traffic permit inter-interface
object network Inside-Network
subnet 10.2.0.0 255.255.240.0
description Inside Network
object network NETWORK_OBJ_192.168.1.0_27
subnet 192.168.1.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network VPNPool
subnet 192.168.1.0 255.255.255.0
description VPNPool
object network VPN-POOL
subnet 192.168.1.0 255.255.255.0
object network LAN
subnet 10.2.1.0 255.255.255.0
access-list inside_access_in extended permit ip object LAN any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool RAIPSECPOOL 192.168.1.1-192.168.1.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside,outside) source static LAN LAN destination static VPN-POOL VPN-POOL
nat (inside,outside) after-auto source dynamic any interface
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 212.135.154.129 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable 4430
http 10.2.0.0 255.255.240.0 management
http 10.2.0.0 255.255.240.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet 10.2.0.0 255.255.240.0 inside
telnet timeout 5
ssh 10.2.0.0 255.255.240.0 management
ssh 10.2.0.0 255.255.240.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 10
console timeout 0
dhcpd address 10.2.1.253-10.2.2.252 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RAIPSECTUNNEL internal
group-policy RAIPSECTUNNEL attributes
dns-server value 10.2.1.7 10.2.1.8
vpn-tunnel-protocol ikev1
default-domain value perfectdomain.perfect-image.co.uk
username KI-Admin password OMa9XVzN1OQ0Is.6 encrypted privilege 15
username PI-Admin password BEGl74DXS9pqUL6v encrypted privilege 15
tunnel-group RAIPSECTUNNEL type remote-access
tunnel-group RAIPSECTUNNEL general-attributes
address-pool RAIPSECPOOL
default-group-policy RAIPSECTUNNEL
tunnel-group RAIPSECTUNNEL ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f50aaad7c3ecaf94382ff0cc887bb5ac
: end -
Problem with Remote Access VPN on ASA 5505
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
Begin connection process
3 15:09:21.287 12/11/12 Sev=Info/4 CM/0x63100004
Establish secure connection
4 15:09:21.287 12/11/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
5 15:09:21.287 12/11/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
6 15:09:21.287 12/11/12 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
7 15:09:21.303 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
8 15:09:21.365 12/11/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
9 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
10 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
11 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
12 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
13 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
14 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
15 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
16 15:09:21.334 12/11/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
17 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
18 15:09:21.334 12/11/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
19 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xFBCE, Remote Port = 0x1194
20 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
21 15:09:21.334 12/11/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 15:09:21.365 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 15:09:21.365 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 15:09:21.365 12/11/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 15:09:21.474 12/11/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
26 15:09:21.474 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
27 15:09:27.319 12/11/12 Sev=Info/4 CM/0x63100017
xAuth application returned
28 15:09:27.319 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
29 15:09:27.365 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
30 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
31 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
32 15:09:27.365 12/11/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
33 15:09:27.365 12/11/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
34 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
35 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
36 15:09:27.397 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
37 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
38 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
39 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
40 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
41 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
42 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO
43 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
44 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.2(5) built by builders on Fri 20-May-11 16:00
45 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
46 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
47 15:09:27.397 12/11/12 Sev=Info/4 CM/0x63100019
Mode Config data received
48 15:09:27.412 12/11/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
49 15:09:27.412 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
50 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
51 15:09:27.444 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
52 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
53 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 6 seconds, setting expiry to 86394 seconds from now
54 15:09:27.459 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
55 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:NO_PROPOSAL_CHOSEN) from **.**.***.***
56 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DEL) to **.**.***.***
57 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000049
Discarding IPsec SA negotiation, MsgID=CE99A8A8
58 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
59 15:09:27.459 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
60 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000058
Received an ISAKMP message for a non-active SA, I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924
61 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(Dropped) from **.**.***.***
62 15:09:27.490 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
63 15:09:30.475 12/11/12 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
64 15:09:30.475 12/11/12 Sev=Info/4 CM/0x63100012
Phase 1 SA deleted before first Phase 2 SA is up cause by "DEL_REASON_IKE_NEG_FAILED". 0 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
65 15:09:30.475 12/11/12 Sev=Info/5 CM/0x63100025
Initializing CVPNDrv
66 15:09:30.475 12/11/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 0.
67 15:09:30.475 12/11/12 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
68 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
69 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
70 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
71 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
The running configuration is as follows (there is a site-to-site VPN set up as well to another ASA 5505, but that is working flawlessly):
: Saved
ASA Version 8.2(5)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
boot system disk0:/asa825-k8.bin
ftp mode passive
access-list outside_nat0_outbound extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit NCHCO 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (outside) 0 access-list outside_nat0_outbound
route outside 0.0.0.0 0.0.0.0 74.219.208.49 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec transform-set l2tp-transform mode transport
crypto ipsec transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_3DES_MD5
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp ipsec-over-tcp port 10000
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHVPN internal
group-policy NCHVPN attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value NCHCO
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password QhZZtJfwbnowceB7 encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
pre-shared-key *****
tunnel-group NCHVPN type remote-access
tunnel-group NCHVPN general-attributes
address-pool VPN_Pool
default-group-policy NCHVPN
tunnel-group NCHVPN ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:15852745977ff159ba808c4a4feb61fa
: end
asdm image disk0:/asdm-645.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Anyone have any idea why this is happening?
Thanks!Thanks again for your reply, and sorry about the late response, havent gotten back to this issue until just now. I applied the above command as you specified, and unfortunately, it did not resolve the problem. Below are the logs from the VPN Client for the connection + attempted browsing of a network share that is behind the ASA, and the new running configuration.
VPN Client Log:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
331 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100002
Begin connection process
332 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100004
Establish secure connection
333 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "69.61.228.178"
334 13:11:41.362 12/17/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 69.61.228.178.
335 13:11:41.362 12/17/12 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
336 13:11:41.424 12/17/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
337 13:11:41.362 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 69.61.228.178
338 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
339 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from 69.61.228.178
340 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
341 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
342 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
343 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
344 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
345 13:11:41.393 12/17/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
346 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 69.61.228.178
347 13:11:41.393 12/17/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
348 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xD271, Remote Port = 0x1194
349 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
350 13:11:41.393 12/17/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
351 13:11:41.424 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
352 13:11:41.424 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
353 13:11:41.424 12/17/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
354 13:11:41.424 12/17/12 Sev=Info/4 CM/0x63100017
xAuth application returned
355 13:11:41.424 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
356 13:11:41.456 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
357 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
358 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
359 13:11:41.456 12/17/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
360 13:11:41.456 12/17/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
361 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
362 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
363 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
364 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
365 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
366 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
367 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
368 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
369 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
370 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
371 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
372 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
373 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
374 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
375 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
376 13:11:41.502 12/17/12 Sev=Info/4 CM/0x63100019
Mode Config data received
377 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = 69.61.228.178, Remote IP = 0.0.0.0
378 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 69.61.228.178
379 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
380 13:11:41.534 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from 69.61.228.178
381 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
382 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 0 seconds, setting expiry to 86400 seconds from now
383 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
384 13:11:41.549 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from 69.61.228.178
385 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
386 13:11:41.549 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to 69.61.228.178
387 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=C4F5B5A6 OUTBOUND SPI = 0xD2DBADEA INBOUND SPI = 0x14762837)
388 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xD2DBADEA
389 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x14762837
390 13:11:41.549 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
391 13:11:41.877 12/17/12 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
392 13:11:43.455 12/17/12 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
393 13:11:43.455 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 266
394 13:11:47.517 12/17/12 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
395 13:11:47.517 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
69.61.228.178 255.255.255.255 192.168.1.1 192.168.1.162 100
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.2 255.255.255.255 192.168.1.162 192.168.1.162 100
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 266
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 266
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 266
396 13:11:47.517 12/17/12 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
397 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310001A
One secure connection established
398 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.1.162. Current hostname: MATT-PC, Current address(es): 192.168.2.70, 192.168.1.162.
399 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: MATT-PC, Current address(es): 192.168.2.70, 192.168.1.162.
400 13:11:47.517 12/17/12 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
401 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
402 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
403 13:11:47.517 12/17/12 Sev=Info/6 IPSEC/0x6370002C
Sent 109 packets, 0 were fragmented.
404 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
405 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
406 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xeaaddbd2 into key list
407 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
408 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x37287614 into key list
409 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
410 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 192.168.1.162. SG: 69.61.228.178
411 13:11:47.517 12/17/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
412 13:11:52.688 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
413 13:11:52.688 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476009
414 13:11:52.704 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
415 13:11:52.704 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
416 13:11:52.704 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476009, seq# expected = 2722476009
417 13:12:03.187 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
418 13:12:03.187 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476010
419 13:12:03.202 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
420 13:12:03.202 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
421 13:12:03.202 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476010, seq# expected = 2722476010
422 13:12:14.185 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
423 13:12:14.185 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476011
424 13:12:14.201 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
425 13:12:14.201 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
426 13:12:14.201 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476011, seq# expected = 2722476011
427 13:12:24.762 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
428 13:12:24.762 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476012
429 13:12:24.778 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
430 13:12:24.778 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
431 13:12:24.778 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476012, seq# expected = 2722476012
New running configuration:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:b6ce58676b6aaeba48caacbeefea53a5
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
I'm at a loss myself as to why this isn't working, and i'm sure that you are running out of solutions yourself. Any other ideas? I really need to get this working.
Thanks so much!
Matthew -
Remote access vpn clients, access to Internet resources
Hello, we currently have a remote access vpn set up terminating on an ASA 5520. Remote access users connect into this ASA and are able to access resources inside of the firewall- the public IP of the ASA is 1.1.1.135. We need these users to be able to access resources natted behind another ASA firewall on the same public IP segment, at IP address 1.1.1.165.
I have gotten to the point where I believe I have all of my Nat/global statements in place, along with my ACLs on both firewalls, but I am not able to make the connection to the server behind the second ASA.
running packet tracer on the second ASA (hosting the 1.1.1.165 server) shows that the packet will be allowed. RUnning packet tracer on the Remote access VPN ASA is showing that the packet is dropped due to :
Action: drop
Drop-reason: (ipsec-spoof) IPSEC Spoof detected
To me, this should be a simple setup, very similar to a company that tunnels all traffic (including Internet traffic) for remote access VPN users. It just doesn't seem like my traffic is getting to the second ASA wioth the remote host.
Anyone have any ideas?I figured out the answer- I had to add a nat statement form my VPN user subnet to be natted to the outside global IP:
nat (outside) 1 10.2.2.0 255.255.255.0 (this is my vpn subnet)
global (outside) 1 interface -
ASA Remote Access VPN Clients - Multiple DNS Suffixes?
Hi community!
I am setting up a new remote access VPN using the traditional IPSec client via ASA 5515-X runnning OS 8.6.1(5).
We require to provide each client multiple DNS suffixes, but are only to provide a single DNS suffix in the grouip policy.
I have tested using an external DHCP server, but using our Windows Server 2008 infrastructure and Option 119 the list is not provided to clients, and I have read that Windows 7 clietns may ignore this option anyway.
Other than umanually configuring the clients , does anybody have any other suggestions on how we may get this to work?
Full marks for helpful posts!
Kind regards, Ash.Hi
I am looking into the same issue, and I am finding conflicting documentation about this and wondered if you got the answers you were looking for.
I have a remote access requirement for users from separate AD's to authenticate through an ASA.
I was reading about Global Catalogue Server but this is not specifically what I want; and also creating a new AAA server group but the user would need to accept which group to use when they log in
Regards -
Remote Access VPN on Cisco ASA Problem
Hi, i configured Remote access VPN on Cisco ASA 8.x as per below configuration.
Problem is that my internet has stopped working, and default route is just showing stars.
i can ping internal server 10.110.10.150 fine , which i allowed on VPN ACL, but my other traffic not going to regular internet on my laptop,
what additional required to force my internet to go to regular internet instead of getting encrypted?
Also attaching output of route print at the point when VPN is connected.
ip local pool RA_VPN_POOL 10.1.200.100-10.1.200.150 mask 255.255.255.0
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto dynamic-map RA_VPN 65535 set transform-set ESP-AES-128-SHA
crypto dynamic-map RA_VPN 65535 set security-association lifetime seconds 28800
crypto dynamic-map RA_VPN 65535 set security-association lifetime kilobytes 4608000
crypto map VPN_MAP 65535 ipsec-isakmp dynamic RA_VPN
crypto map VPN_MAP interface outside
isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
tunnel-group ITT_RA type remote-access
tunnel-group ITT_RA general-attributes
address-pool RA_VPN_POOL
default-group-policy RA_VPN_GP
tunnel-group ITT_RA ipsec-attributes
pre-shared-key <group key>
group-policy RA_VPN_GP internal
group-policy RA_VPN_GP attributes
dns-server value 10.0.0.1 10.0.0.2
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Split_Tunnel_List
default-domain value mydomain.com
address-pools value RA_VPN_POOL
access-list Split_Tunnel_List extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
access-list nonattest extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
nat (inside) 0 access-list nonattest
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 10.111.36.1 10.111.36.9 276
0.0.0.0 0.0.0.0 On-link 10.1.200.100 20
10.1.200.0 255.255.255.0 On-link 10.1.200.100 276
10.1.200.100 255.255.255.255 On-link 10.1.200.100 276
10.1.200.255 255.255.255.255 On-link 10.1.200.100 276
10.110.10.150 255.255.255.255 10.1.200.1 10.1.200.100 100
10.111.36.0 255.255.255.0 On-link 10.111.36.9 276Hi, i configured Remote access VPN on Cisco ASA 8.x as per below configuration.
Problem is that my internet has stopped working, and default route is just showing stars.
i can ping internal server 10.110.10.150 fine , which i allowed on VPN ACL, but my other traffic not going to regular internet on my laptop,
what additional required to force my internet to go to regular internet instead of getting encrypted?
Also attaching output of route print at the point when VPN is connected.
ip local pool RA_VPN_POOL 10.1.200.100-10.1.200.150 mask 255.255.255.0
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto dynamic-map RA_VPN 65535 set transform-set ESP-AES-128-SHA
crypto dynamic-map RA_VPN 65535 set security-association lifetime seconds 28800
crypto dynamic-map RA_VPN 65535 set security-association lifetime kilobytes 4608000
crypto map VPN_MAP 65535 ipsec-isakmp dynamic RA_VPN
crypto map VPN_MAP interface outside
isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
tunnel-group ITT_RA type remote-access
tunnel-group ITT_RA general-attributes
address-pool RA_VPN_POOL
default-group-policy RA_VPN_GP
tunnel-group ITT_RA ipsec-attributes
pre-shared-key <group key>
group-policy RA_VPN_GP internal
group-policy RA_VPN_GP attributes
dns-server value 10.0.0.1 10.0.0.2
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Split_Tunnel_List
default-domain value mydomain.com
address-pools value RA_VPN_POOL
access-list Split_Tunnel_List extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
access-list nonattest extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
nat (inside) 0 access-list nonattest
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 10.111.36.1 10.111.36.9 276
0.0.0.0 0.0.0.0 On-link 10.1.200.100 20
10.1.200.0 255.255.255.0 On-link 10.1.200.100 276
10.1.200.100 255.255.255.255 On-link 10.1.200.100 276
10.1.200.255 255.255.255.255 On-link 10.1.200.100 276
10.110.10.150 255.255.255.255 10.1.200.1 10.1.200.100 100
10.111.36.0 255.255.255.0 On-link 10.111.36.9 276 -
Remote access VPN with ASA 5510 using DHCP server
Hi,
Can someone please share your knowledge to help me find why I am not able to receive an IP address on remote access VPN connection while I can get an IP address on local DHCP pool?
I am trying to setup remote access VPN with ASA 5510. It works with local dhcp pool but doesn't seem to work when I tried using an existing DHCP server. It is being tested in an internal network as follows:
ASA Version 8.2(5)
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.6.0.12 255.255.254.0
ip local pool testpool 10.6.240.150-10.6.240.159 mask 255.255.248.0 !(worked with this)
route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
crypto ipsec transform-set FirstSet esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map dyn1 1 set transform-set FirstSet
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface inside
crypto isakmp enable inside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
vpn-addr-assign aaa
vpn-addr-assign dhcp
group-policy testgroup internal
group-policy testgroup attributes
dhcp-network-scope 10.6.192.1
ipsec-udp enable
ipsec-udp-port 10000
username testlay password *********** encrypted
tunnel-group testgroup type remote-access
tunnel-group testgroup general-attributes
default-group-policy testgroup
dhcp-server 10.6.20.3
tunnel-group testgroup ipsec-attributes
pre-shared-key *****
I got following output when I test connect to ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + VENDO
4024 bytesR copied in 3.41 0 secs (1341 by(tes/sec)13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing SA payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ISA_KE payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received DPD VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: True Aggressive Mode: False
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received NAT-Traversal ver 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received Cisco Unity client VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, Connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing IKE SA payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA Proposal # 1, Transform # 9 acceptable Matches global IKE entry # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing ISAKMP SA payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for Responder...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing ID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Computing hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing Cisco Unity VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing xauth V6 VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing NAT-Traversal VID ver 02 payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing Fragmentation VID + extended capabilities payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + HASH (8) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + HASH (8) + NOTIFY (11) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Computing hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Processing IOS/PIX Vendor ID payload (version: 1.0.0, capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Received Cisco Unity client VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
kens-mgmt-012# P = 10.15.200.108, Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing blank hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing qm hash payload
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=d4ca48e4) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=d4ca48e4) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): Enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Processing MODE_CFG Reply attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary WINS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary WINS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: IP Compression = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling Policy = Disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Browser Proxy Setting = no-modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Browser Proxy Bypass Local = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, User (testlay) authenticated.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing blank hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing qm hash payload
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=6b1b471) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=6b1b471) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): Enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Processing cfg ACK attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=49ae1bb8) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): Enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Processing cfg Request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for IPV4 net mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for DNS server address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for WINS server address!
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Received unsupported transaction mode attribute: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Save PW setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Default Domain Name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Split Tunnel List!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Client Browser Proxy Setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for backup ip-sec peer list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Client Smartcard Removal Disconnect Setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Application Version!
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Client Type: WinNT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for DHCP hostname for DDNS is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Duplicate Phase 2 packet detected. No last packet to retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=b04e830f) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Duplicate Phase 2 packet detected. No last packet to retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE received response of type [] to a request from the IP address utility
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Cannot obtain an IP address for remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE TM V6 FSM error history (struct &0xd8030048) <state>, <event>: TM_DONE, EV_ERROR-->TM_BLD_REPLY, EV_IP_FAIL-->TM_BLD_REPLY, NullEvent-->TM_BLD_REPLY, EV_GET_IP-->TM_BLD_REPLY, EV_NEED_IP-->TM_WAIT_REQ, EV_PROC_MSG-->TM_WAIT_REQ, EV_HASH_OK-->TM_WAIT_REQ, NullEvent
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE AM Responder FSM error history (struct &0xd82b6740) <state>, <event>: AM_DONE, EV_ERROR-->AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL-->AM_TM_INIT_MODECFG_V6H, NullEvent-->AM_TM_INIT_MODECFG, EV_WAIT-->AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG-->AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK-->AM_TM_INIT_XAUTH_V6H, NullEvent-->AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b terminating: flags 0x0945c001, refcnt 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending delete/delete with reason message
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing blank hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing IKE delete payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing qm hash payload
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=9de30522) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 80
Regards,
LayFor RADIUS you need a aaa-server-definition:
aaa-server NPS-RADIUS protocol radius
aaa-server NPS-RADIUS (inside) host 10.10.18.12
key *****
authentication-port 1812
accounting-port 1813
and tell your tunnel-group to ask that server:
tunnel-group VPN general-attributes
authentication-server-group NPS-RADIUS LOCAL
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni -
ASA Remote Access VPN: internal LAN cannot connect to connected VPN clients
Hi community,
I configured IPSec remote Access VPN in ASA, and remote client use Cisco VPN client to connect to the HQ. The VPN is working now, VPN clients can connect to Servers inside and IT's subnet, but from my PC or Servers inside LAN cannot ping or initial a RDP to connected VPN clients. Below is my configuration:
object-group network RemoteVPN_LocalNet
network-object 172.29.168.0 255.255.255.0
network-object 172.29.169.0 255.255.255.0
network-object 172.29.173.0 255.255.255.128
network-object 172.29.172.0 255.255.255.0
access-list Split_Tunnel remark The Corporation network behind ASA
access-list Split_Tunnel extended permit ip object-group RemoteVPN_LocalNet 10.88.61.0 255.255.255.0
ip local pool remotevpnpool 10.88.61.10-10.88.61.15 mask 255.255.255.0
nat (inside,outside) source static Allow_Go_Internet Allow_Go_Internet destination static remotevpnpool remotevpnpool
crypto ipsec ikev1 transform-set myset esp-aes esp-sha-hmac
crypto dynamic-map dyn1 1 set ikev1 transform-set myset
crypto map mymap 65000 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
tunnel-group remotevpngroup type remote-access
tunnel-group remotevpngroup general-attributes
address-pool remotevpnpool
authentication-server-group MS_LDAP LOCAL
default-group-policy Split_Tunnel_Policy
I don't know what I miss in order to have internal LANs initial connection to connected vpn clients. Please guide me.
Thanks in advanced.Hi tranminhc,
Step 1: Create an object.
object network vpn_clients
subnet 10.88.61.0 mask 255.255.255.0
Step 2: Create a standard ACL.
access-list my-split standard permit ip object RemoteVPN_LocalNet
Step 3: Remove this line, because I am not sure what "Allow_Go_Internet" included for nat-exemption.
no nat (inside,outside) source static Allow_Go_Internet Allow_Go_Internet destination static remotevpnpool remotevpnpool
Step 4: Create new nat exemption.
nat (inside,outside) source static RemoteVPN_LocalNet RemoteVPN_LocalNet destination static vpn_clients vpn_clients
Step 5: Apply ACL on the tunnel.
group-policy Split_Tunnel_Policy attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value my-split
Step 6:
I assume you have a default route on your inside L3 switch point back to ASA's inside address. If you don't have one.
Please add a default or add static route as shown below.
route 10.88.61.0 mask 255.255.255.0 xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx = equal to ASA's inside interface address.
Hope this helps.
Thanks
Rizwan Rafeek -
Does ASA Service Module on 6509-E support Remote Access VPN ?
I'm having a problem configuring Remote Access VPN (SSL, Anyconnect ect.) on ASA Service Module on 6509-E. Is this even supported or am i wasting my time trying to make something work which will not work in a first place :) ? Site-to-Site works without any problems.
Tech Info:
6509-E running SUP 2T 15.1(2)SY
ASA Module - WS-SVC-ASA-SM1 running image - asa912-smp-k8 & asdm-712
Licenses on ASA:
Encryption-DES - Enabled
Encryption-3DES-AES -Enabled
Thanks in Advance for support.Are you running multiple context mode?
If you are, remote access VPN is not supported in that case:
"Note Multiple context mode only applies to IKEv2 and IKEv1 site to site and does not apply to AnyConnect, clientless SSL VPN, the legacy Cisco VPN client, the Apple native VPN client, the Microsoft native VPN client, or cTCP for IKEv1 IPsec."
Reference. -
Can you create a Remote Access VPN connection to tunnel DMZ LAN and Inside Networks simultaneously?
I have a customer that has a ASA 5510 version 8.3 with IPSEC Client Access that includes some of their networks on the Inside interface. The issue they are having is when their mobile users connect with the vpn client (which is using split tunneling), they can no longer access their web server applications that are running in the DMZ. Without the client connected, they access the web servers via the external public IP. Once they are connected via vpn, their default dns server becomes the internal AD DNS server, which resolves the DNS of the web servers to the private DMZ ip address.
Can a Remote Access VPN client connection be allowed to connect to both the DMZ interface and the Inside Interface? I had always only setup RA VPN clients to connect to networks on the Inside Interface.
I tried adding the DMZ network to the Split Tunnel list, but I could not access anything it while connected to vpn using the private IP addresses.Yes, you should be able to access DMZ subnets as well if they are added to the split tunnel ACL. You could check the NAT exemption configuration for the DMZ and also check if the ASA is forwarding the packet through DMZ interface by configuring captures on the DMZ interface.
Share the configuration if you want help with the NAT exemption part. -
Hi All,
I'm looking to setup a Remote Access VPN via my ASA 5510. The clients will be using Cisco Anyconnect (which I assume is compatible...?) When I use the wizard it only mentions Cisco VPN Client.
When my clients connect up to the ASA via Anyconect, can I get them to just use DHCP via my AD servers or do I need to configure a seperate independent scope specifically for VPN clients?
ThanksHi Grant,
When you configure Remote access VPN , you need to configure a seprated pool of ip address for the vpn user.
Regards,
Bikas R.Pandey. -
Remote Access VPN - add new internal IP
Hi
I have a existing Cisco VPN client configuration into ASA 5510 for remote access.
Group name : ISETANLOT10
Group password : xxxx
IP pool : lot10ippool, 172.27.17.240 - 172.27.17.245
enycrption : 3DES
authentication : SHA
the connection was successful and i was able to ping to the internal server of 172.47.1.10.
Now there is request for the same VPN remote access to be able to ping access a new server inside LAN, 172.57.1.10 & 172.57.1.20
But with the same VPN access, i was unable to ping both new IP.
How can i add in the both IP to be able to ping using the same remote access VPN config?
I attached below existing config (edited version)
===
: Saved
ASA Version 8.0(4)
hostname asalot10
names
name 172.17.100.22 NAVNew
name 172.27.17.215 NECUser
name 172.47.1.10 NarayaServer description Naraya Server
name 62.80.122.172 NarayaTelco1
name 62.80.122.178 NarayaTelco2
name 172.57.1.10 IPVSSvr description IPVSSvr
name 122.152.181.147 Japan01
name 122.152.181.0 Japan02
name 175.139.156.174 Outside_Int
name 178.248.228.121 NarayaTelco3
name 172.67.1.0 VCGroup
name 172.57.1.20 IPVSSvr2
object-group service NECareService
description Remote NECareService
service-object tcp eq https
service-object tcp eq ssh
service-object icmp echo-reply
access-list inside_access_in extended deny ip any Japan02 255.255.255.0
access-list inside_access_in extended permit ip VCGroup 255.255.255.0 any
access-list inside_access_in extended deny tcp object-group PermitInternet any object-group torrent1
access-list inside_access_in extended permit ip object-group PermitInternet any log disable
access-list inside_access_in extended permit ip host NarayaServer any log disable
access-list inside_access_in extended permit ip host IPVSSvr any
access-list inside_access_in extended permit ip host NAVNew any log disable
access-list inside_access_in extended permit ip host 172.17.100.30 any
access-list outside_access_in extended permit object-group NECareService object-group NECare any
access-list outside_access_in extended permit ip object-group DM_INLINE_NETWORK_1 host NarayaServer
access-list outsidein extended permit tcp any host Outside_Int eq https
access-list outsidein extended permit object-group rdp any host Outside_Int log debugging
access-list outsidein extended permit tcp object-group DM_INLINE_NETWORK_2 host Outside_Int eq 8080
access-list outsidein extended permit ip object-group DM_INLINE_NETWORK_3 host IPVSSvr
access-list inside_mpc extended permit object-group TCPUDP any any eq www
access-list inside_mpc extended permit tcp any any eq www
access-list inside_nat0_outbound extended permit ip any 172.27.17.240 255.255.255.248
access-list inside_nat0_outbound extended permit ip host NarayaServer object-group Nry_Png
access-list inside_nat0_outbound extended permit ip host IPVSSvr2 172.27.17.240 255.255.255.248
access-list outside_cryptomap extended permit ip object-group Naraya_Png object-group Nry_Png
global (outside) 10 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 10 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface 8080 NarayaServer 8080 netmask 255.255.255.255
static (inside,outside) tcp interface 3389 NAVNew 3389 netmask 255.255.255.255
static (inside,outside) tcp interface ssh IPVSSvr2 ssh netmask 255.255.255.255
access-group outsidein in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 175.139.156.173 1
route inside 172.17.100.20 255.255.255.255 172.27.17.100 1
route inside NAVNew 255.255.255.255 172.27.17.100 1
route inside 172.17.100.30 255.255.255.255 172.27.17.100 1
route inside NarayaServer 255.255.255.255 172.27.17.100 1
route inside 172.47.1.11 255.255.255.255 172.27.17.100 1
route inside VCGroup 255.255.255.0 172.27.17.100 1
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime seconds 28800
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 218.x.x.105
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 1 set security-association lifetime seconds 28800
crypto map outside_map 1 set security-association lifetime kilobytes 4608000
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
group-policy ISETANLOT10 internal
group-policy ISETANLOT10 attributes
dns-server value 172.27.17.100
vpn-tunnel-protocol IPSec l2tp-ipsec
username nectier3 password dPFBFnrViJi/LGbT encrypted privilege 0
username nectier3 attributes
vpn-group-policy ISETANLOT10
username necare password BkPn6VQ0VwTy7MY7 encrypted privilege 0
username necare attributes
vpn-group-policy ISETANLOT10
username naraya password pcGKDau9jtKgFWSc encrypted
username naraya attributes
vpn-group-policy ISETANLOT10
service-type nas-prompt
tunnel-group ISETANLOT10 type remote-access
tunnel-group ISETANLOT10 general-attributes
address-pool lot10ippool
default-group-policy ISETANLOT10
tunnel-group ISETANLOT10 ipsec-attributes
pre-shared-key *
tunnel-group 218.x.x.105 type ipsec-l2l
tunnel-group 218.x.x.105 ipsec-attributes
pre-shared-key *
tunnel-group ivmstunnel type remote-access
tunnel-group ivmstunnel general-attributes
address-pool lot10ippool
tunnel-group ivmstunnel ipsec-attributes
pre-shared-key *
!=====The remote access VPN should allow the connection but I am guessing your ASA doesn't know how to route to the two new destinations.
You have a name and static route for the working server at 172.47.1.10:
name 172.47.1.10 NarayaServer description Naraya Server
route inside NarayaServer 255.255.255.255 172.27.17.100 1
..but no equivalent for the two new hosts. As a result, any traffic from the ASA destined for them will attempt to use the default route (via the outside interface).
If you add:
route inside 172.57.1.10 255.255.255.255 172.27.17.100
route inside 172.57.1.20 255.255.255.255 172.27.17.100
(assuming that's your correct gateway), it should work. -
Remote access VPN client gets connected fails on hosts in LAN
Hi,
VPN client gets connected fine, I have a inter VLAN routing happening on the switch in the LAN so all the LAN hosts have gateway IP on the switch, I have the defult route pointing to ASA inside interface on the switch, the switch I can reach after Remote Access VPN is connected how ever I cannot ping/connect to other hosts in the LAN and if I make the gateway point to the ASA then that host is accessible, any suggestions? I really want to have gateway to be the Switch as I have other networks reachable through the Switch (Intranet routing)Hi Mashal,
Thanks for your time,
VPN Pool(Client) 192.168.100.0/24
Internal Subnets 192.9.200.0/24(VLAN 4000) and 192.168.2.0/24 (VLAN 1000)
=============
On the Switch
=============
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 192.168.2.5 to network 0.0.0.0
172.32.0.0/24 is subnetted, 1 subnets
C 172.32.0.0 is directly connected, Vlan101
C 192.168.200.0/24 is directly connected, Vlan2000
C 192.9.200.0/24 is directly connected, Vlan4000
S 192.168.250.0/24 [1/0] via 192.9.200.125
S 192.168.1.0/24 [1/0] via 192.9.200.125
C 192.168.2.0/24 is directly connected, Vlan1000
S 192.168.252.0/24 [1/0] via 192.9.200.125
S* 0.0.0.0/0 [1/0] via 192.168.2.5
===============
On ASA
===============
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is 172.32.0.2 to network 0.0.0.0
C 172.32.0.0 255.255.255.0 is directly connected, outside
C 192.9.200.0 255.255.255.0 is directly connected, inside
C 192.168.168.0 255.255.255.0 is directly connected, failover
C 192.168.2.0 255.255.255.0 is directly connected, MGMT
S 192.168.100.2 255.255.255.255 [1/0] via 172.32.0.2, outside
S 192.168.100.3 255.255.255.255 [1/0] via 172.32.0.2, outside
S* 0.0.0.0 0.0.0.0 [1/0] via 172.32.0.2, outside
We don't need route print on the PC for now as I can explain what is happening I can get complete access to the 192.168.2.0/24 (VLAN 1000) but for 192.9.200.0/24 (VLAN 4000) above from the switch I can only ping IP's on the switches/pair but cannot have any tcp connections, which explains the default route being pointed on the switch is on VLAN 1000, now my issue is How do I get access to VLAN 4000 as you can see these two are on different Interfaces/zones on the ASA and please note with default gateway pointing to ASA I will have access to both the VLAN's it is only when I move the gateway pointing to Switch I loose tcp connections to one VLAN depending on the default route on the being pointing to on the switch.
So we are left to do with how to on the switch with default route. -
Remote Access VPN Support in Multiple Context Mode (9.1(2))?
Hi Guys,
I am currently running two Cisco ASA5520 (ASA Version: 9.1(2)) firewalls in Active/Standby failover and was contemplating the option of migrating my remote access VPN to these firewalls. However seeing that the new IOS now support mixed multiple context mode and dynamic routing. Is it safe to ask whether or not Remote Access VPN is now support in this IOS upgrade?
Multiple Context Mode New Features:
Site-to-Site VPN in multiple context mode | Site-to-site VPN tunnels are now supported in multiple context mode.
New resource type for site-to-site VPN tunnels | New resource types, vpn other and vpn burst other, were created to set the maximum number of site-to-site VPN tunnels in each context.
Dynamic routing in Security Contexts | EIGRP and OSPFv2 dynamic routing protocols are now supported in multiple context mode. OSPFv3, RIP, and multicast routing are not supported.
New resource type for routing table entries | A new resource class, routes, was created to set the maximum number of routing table entries in each context. We modified the following commands: limit-resource, show resource types, show resource usage, show resource allocation. We modified the following screen: Configuration > Context Management > Resource Class > Add Resource Class.
Mixed firewall mode support in multiple context mode | You can set the firewall mode independently for each security context in multiple context mode, so some can run in transparent mode while others run in routed mode. We modified the following command: firewall transparent. You cannot set the firewall mode in ASDM; you must use the command-line interface. Also available in Version 8.5(1).
Regards,
LeonHey Leon,
According to the ASA 9.1 Configuration Guide, Remote Access VPN is not yet supported with version 9.1(2). Only Site-to-Site VPN support in multiple context was introduced with release ASA 9.0(x). This was mentioned in the 9.0(x) release notes.
Regards,
Dennis -
I have problem for authenticar a remote access VPN with ACS 5.0, not work.
When I try with ACS 4.1, the authentication work fine.
I hope someone can help me.
Regards.I have the same problem. I'm using ASA v8.21 and ACS v5.0.0.21, which I'm using as tacacs and radius server. I have no problem with accessing devices via tacacs (except that changing pass with first login doesn't work). The problem is with VPN authentication. I tested radius with Radlogin and PAP is working fine, CHAP goes in timeout, but as I know ACS 5.0 doesn't suport CHAP.
Here are some logs from ASA:
the end of debug crypto isakmp:
Sep 04 15:01:35 [IKEv1]: Group = radiusACS, Username = user1, IP = X.X.X.X, Error: Unable to remove PeerTblEntry
Sep 04 15:01:35 [IKEv1 DEBUG]: Deleting active auth handle during SA deletion: handle = 1844
debug radius:
Sep 04 2010 15:08:53: %ASA-7-713906: IP = X.X.X.X, Connection landed on tunnel_group radiusACS
Sep 04 2010 15:08:53: %ASA-6-713172: Group = radiusACS, IP = X.X.X.X, Automatic NAT Detection Status: Remote end IS behind a NAT device This end is NOT behind a NAT device
Sep 04 2010 15:08:53: %ASA-7-715046: Group = radiusACS, IP = X.X.X.X, constructing blank hash payload
Sep 04 2010 15:08:53: %ASA-7-715046: Group = radiusACS, IP = X.X.X.X, constructing qm hash payload
Sep 04 2010 15:08:53: %ASA-7-713236: IP = X.X.X.X, IKE_DECODE SENDING Message (msgid=f9163eb8) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 72
Sep 04 2010 15:08:53: %ASA-7-713236: IP = X.X.X.X, IKE_DECODE RECEIVED Message (msgid=f9163eb8) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 86
Sep 04 2010 15:08:53: %ASA-7-715001: Group = radiusACS, IP = X.X.X.X, process_attr(): Enter!
Sep 04 2010 15:08:53: %ASA-7-715001: Group = radiusACS, IP = X.X.X.X, Processing MODE_CFG Reply attributes.
Sep 04 2010 15:08:53: %ASA-7-713906: Group = radiusACS, Username = user1, IP = X.X.X.X, Authentication Failure: Unsupported server type!
Sep 04 2010 15:08:53: %ASA-7-715065: Group = radiusACS, Username = user1, IP = X.X.X.X, IKE TM V6 FSM error history (struct &0xa7b636a8) , : TM_DONE, EV_ERROR-->TM_AUTH, EV_DO_AUTH-->TM_WAIT_REPLY, EV_CHK_MSCHAPV2-->TM_WAIT_REPLY, EV_PROC_MSG-->TM_WAIT_REPLY, EV_HASH_OK-->TM_WAIT_REPLY, NullEvent-->TM_WAIT_REPLY, EV_COMP_HASH-->TM_WAIT_REPLY, EV_VALIDATE_MSG
Sep 04 2010 15:08:53: %ASA-7-715065: Group = radiusACS, Username = user1, IP = X.X.X.X, IKE AM Responder FSM error history (struct &0xac417310) , : AM_DONE, EV_ERROR-->AM_TM_INIT_XAUTH_V6H, EV_TM_FAIL-->AM_TM_INIT_XAUTH_V6H, NullEvent-->AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA-->AM_TM_INIT_XAUTH_V6H, NullEvent-->AM_TM_INIT_XAUTH_V6H, EV_START_TM-->AM_TM_INIT_XAUTH, EV_START_TM-->AM_PROC_MSG3, EV_TEST_TM_H6
Sep 04 2010 15:08:53: %ASA-7-713906: Group = radiusACS, Username = user1, IP = X.X.X.X, IKE SA AM:f7beee8e terminating: flags 0x0105c001, refcnt 0, tuncnt 0
Sep 04 2010 15:08:53: %ASA-7-713906: Group = radiusACS, Username = user1, IP = X.X.X.X, sending delete/delete with reason message
Sep 04 2010 15:08:53: %ASA-7-715046: Group = radiusACS, Username = user1, IP = X.X.X.X, constructing blank hash payload
Sep 04 2010 15:08:53: %ASA-7-715046: Group = radiusACS, Username = user1, IP = X.X.X.X, constructing IKE delete payload
Sep 04 2010 15:08:53: %ASA-7-715046: Group = radiusACS, Username = user1, IP = X.X.X.X, constructing qm hash payload
Sep 04 2010 15:08:53: %ASA-7-713236: IP = X.X.X.X, IKE_DECODE SENDING Message (msgid=e0cd7809) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 80
Sep 04 2010 15:08:53: %ASA-3-713902: Group = radiusACS, Username = user1, IP = X.X.X.X, Removing peer from peer table failed, no match!
Sep 04 2010 15:08:53: %ASA-4-713903: Group = radiusACS, Username = user1, IP = X.X.X.X, Error: Unable to remove PeerTblEntry
Sep 04 2010 15:08:53: %ASA-7-715040: Deleting active auth handle during SA deletion: handle = 1861
Sep 04 2010 15:08:53: %ASA-4-113019: Group = , Username = , IP = 0.0.0.0, Session disconnected. Session Type: , Duration: 0h:00m:00s, Bytes xmt: 0, Bytes rcv: 0, Reason: Unknown
Regards
Maybe you are looking for
-
For the best experience, open this PDF portfolio in Acrobat 9 or Adobe Read
Hi, For the first time I am aware of a user has received a PDF that cannot be opened in Preview. The pdf opens to a splash screen showing, "For the best experience, open this PDF portfolio in Acrobat 9 or Adobe Reader 9, or later." There is a large b
-
Overclocking KT4-Ultra & BIOS 1.4
Hy. I've overclocked my 2400+ to 2300Mhz(170FSB). I had also to upper the core voltage to 1.75v (1.74real) so because of this I get higher temps. The thing is that I use a RaptorCool silent cooler and a 12cm fan blowing cold air into the case. This i
-
User-Defined Aggregate Function in oracle
Somebody knows if in oracle 10g is possible to create a User-Defined Aggregate Function? Sometingh like my_sum, that aggregate the values in a way that i want... select manager, my_sum(salary) group by manager In internet i've found rellay notingh fo
-
11g Read-Only repository on Linux
Hi Currrenty I am struggling with a Read-Only issues on a new install of OBIEE 11g. I have install OBIEE11g on a Linux box and also on a windows server just to use the Repository Administation tool. I then created an ODBC DSN on the windows server to
-
Compare table structure and add the missing columns
Hello, I want to compare the table schema of two tables and update with some plsql code the second one with the missing columns of the fist one : Example SQL> desc a Name Type Nullable Default Comments C1 VARCHAR2(10) Y C2 NUMBER(3) Y C3 NUMBER(10,2)