Multicasting for Flexconnect mode

I have requirement to enable multicasting on wireless network. AP s are on Flexconnect mode. Does Flexconnect mode be enabled for multicast traffic ?

In release 8.0, FlexConnect can join CAPWAP multicast group. The controller should be set to Multicast - Multicast mode for both AP Multicast mode and IPv6 AP Multicast mode.
Note: FlexConnect mode APs will join IPv4 or IPv6 Multicast group if AP Multicast mode is configured as Multicast in release 8.0; however, there will be slight Data through-put degradation impact in the FlexConnect centrally switched scenario compared to AP Multicast mode configured as Unicast.
Note: Smart AP image upgrade does not work on the 7500 controllers when the Master AP is connected over CAPWAPv6.
The following IPv6 specific features are not supported in FlexConnect central switching mode:
■Layer 3 Mobility
■IPv6 VideoStream
http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-0/IPV6_DG.html#pgfId-76826

Similar Messages

Multicast and Flexconnect Local Switching

Hi All,
Hope you can help with this -
I have the following:
A 5508 in a remote datacentre and several sites with AP's running in flexconnect mode, connected to cisco switches.
I have an ssid on which I want to run some push to talk "phones" which I believe use multicast.
What do I need to do to enable multicast for this, I have read many documents but I'm a little confused !
I need to enable multicast on the controller globally ?
Enable igmp snooping ?
Does multicast mode need to be multicast or unicast ?
Do I need a multicast address in this case ?
Do i need to configure the switches (2960) for any multicast configuration, there is none at present ?
The phones that do PTT will only need to talk to other phones locally at each site, but each site will have some phones, does this make any difference to anything ?
hope someone can help, thanks !

The guidelines for Flexconnect and Multicast are as follows:
1. Set the AP Multicate mode on the controller to Unicast (Multicast-Unicast Mode) : The wireless controller replicates the multicast packet and sends it to each Access Point in a Unicast CAPWAP Tunnel
2. L3 routing isn't required on the wired network
3. There will be high controller and wired network loading
4. No multicast address is required in multicast-unicast mode
5. No multicast configuration required on Layer 2 switches as CGMP is enabled by default

Does ACE-30 support multicast in routed mode?

We currently have ACE20's, which only support multicast in bridge mode.
Was wondering if it's the same on ACE30's, or if Cisco finally implemented support for mcast in routed mode.
thx
Kevin

Could you please confirm if this applies to both ACE20 & ACE30, or just ACE20?
If both, when does Cisco plan on supporting mcast in routed mode?
thx
Kevin

Guest Portal Using ISE with Flexconnect Mode

Folks,
I have configured my guest web authentication using ISE with flexconnect mode like this:
http://www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080bcb905.shtml
After done, I connect the SSID but cannot log in. I cannot get IP address and in the ISE I can see that my device has already hit my authorization profile and the status is pending. Can anyone help me with this?

As Richard says, check to see if you have an IP address. If not check the AP settings for FlexConnect. Is the mode on the AP set right? Please confirm that you are using FC local switching and not centralised switching?
Is the VLAN tagging enabled on the AP, and/or the VLANs on the AP switchport set right?

APs in Flexconnect mode, initial AP group

We have deployed many Cisco site specific WLAN controllers worldwide.
We are now testing APs in Flexconnect mode at our branches with regional C8510 controllers running 7.6.110.0. One of the issues that we see is that if we deploy a new AP and get it associated with C8510 controller the AP automatically falls under Default AP group and transmits the first couple of SSIDs that are by default enabled in Default AP group. This is not good as we plan to have hundreds of SSIDs configured for many branches and we do not want a new AP to transmit any SSID until it is assigned to site specific AP and Flexconnect groups. We know the AP can be admin disabled ( or its Radios ) after the first initial procedure and then moved to the right groups but this is a manual process and we want to have something automated in our hands.
Does anyone know if we can get rid of this default behavior?
Thanks,
Vlad

Hi Rasilka,
Thank you. It's not about SSIDs, we broadcast the same SSIDs, but is more about WLANs and their settings. We have our specific security and other internal rules, for example we cannot use the same PSK at all sites etc. Some of the WLANs are the same everywhere, but quite many not. That's why I need to differentiate and have many separate WLANs. It is my understanding C8510 is a top box so to be honest 512 WLAN limit quite surprised me. I want to use it up to its maximum before I need to buy another box.
Regards,
Vlad

UI Control options do not appear for TCD mode and Webdynpro mode

Hi guys,
When I open the screen Start option in eCATT for ECC 7.0, there is no options for TCD mode and Webdynpro mode, only have for SAPGUI mode. So pls help to me find the options for these modes.
Thanks in advance,
Thien

Hello Friend,
This has been corrected by 640 SAPKB64023 and 700 SAPKB70016.
Please install the relevant SP to your system.
Thanks.
Eric Monteiro

Logs for 'Operating mode' change in mirroring

Logs for 'Operating mode' change in mirroring
Hi Everyone,
Is there any log,that shows when the Operating mode of a database involved in mirroring(SQL SERVER 2008 R2) has been changed from asynchronous to synchrous(or vise versa).
Regards,
Aspet
A.G

Try looking into trace log files
DECLARE @filename VARCHAR(100), @filenum int
SELECT @filename = CAST(value AS VARCHAR(100))
FROM fn_trace_getinfo(DEFAULT)
WHERE property = 2
AND traceid = 1
AND value IS NOT NULL
SELECT @filename
SELECT @filename = substring(@filename, 0, charindex('_', @filename)+1) + convert(varchar, (convert(int, substring(left(@filename, len(@filename)-4), charindex('_', @filename)+1, len(@filename)))-4)) + '.trc'
SELECT @filename
SELECT gt.EventClass,
te.Name AS EventName,
gt.TEXTData,
gt.NTUserName,
gt.NTDomainName,
gt.HostName,
gt.ApplicationName,
gt.LoginName,
gt.SPID,
gt.StartTime,
gt.EndTime,
gt.ObjectName,
gt.DatabaseName,
gt.FileName
FROM [fn_trace_gettable](@fileName, DEFAULT) gt
JOIN sys.trace_events te ON gt.EventClass = te.trace_event_id
WHERE EventClass = 116
AND TEXTData LIKE '%Alter
database%'
ORDER BY StartTime;
Best Regards,Uri Dimant SQL Server MVP,
http://sqlblog.com/blogs/uri_dimant/
MS SQL optimization: MS SQL Development and Optimization
MS SQL Blog:
Large scale of database and data cleansing
Remote DBA Services:
Improves MS SQL Database Performance

Turn off adaptive display for AC mode

Hi,
I am in curiosity of how I can turn off adaptive brightness display for external mode.
http://i.imgur.com/nnDnd9Y.jpg
I have already turned it off from Power Options in Control Panel. At first, this did not work alone to turn adaptive brightness off so I also disabled Display Power Saving Technology for battery mode from Intel Graphics Control Panel.
This works like a charm for battery mode but adaptive display is still active when on external power and I could not find an option to disable it in Intel Graphics Control Panel, there isn't Display Power Saving Technology for external power.
http://i.imgur.com/WtLe6kB.jpg
So, how can I stop adaptive brightness for AC power before I go blind of the abrupt changes in brightness when I'm plugged in to the wall?
Any help is appriciated.
Thanks!
This question was solved.
View Solution.

Hi @yldzanl ,
Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP ENVY 15 Notebook and wanted to turn down the brightness on AC mode. On your first screen shot it shows you under the Edit settings. You will notice adjust brightness one for battery mode and the other for AC adapter, they are not the same.
Change this to be the same for battery and save settings.
Thanks should take care of it.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

How can I set default values for Allocate Mode in AO config?

Hi, How can I set default values for allocate mode in AO config. To be specific, in the attached vi, I need to set the Allocate Mode in AO Config to 'Use FIFO Memory (6)' if the value inside my case structure is false and to 'no change (0)' if the value inside the case strusture is true.
Solved!
Go to Solution.
Attachments:
generateWaveformFIFO.vi ‏15 KB

Create two constants for the Allocate Mode input (right click > create > constant). Place one in the true case of the case structure, and place the other one in the false case. Wire them to the same tunnel (border of the case structure), then wire the tunnel to the Allocate Mode terminal of the AO Config. I don't have Traditional DAQ installed, but that should do it.
Misha

Tables for PDS modes and capacity requirements

Does anyone know which tables store the Mode and Capacity Requirement data for SNP PDSs? In particular I am looking for the Mode Duration and Capacity Requirement Bucket Resource Consumption fields.
Thanks,
Laurence.

Thanks Nanda,
I am unable to find this BAPI on our system (we are on SCM 4.1). Do you know the tables that store SNP PDS Mode and Capacity Requirement data?
Regards,
Laurence.

My iphone 3gs shows white screen i restored it in itunes then to same problem once i connect my phone to charge i can hear the sound and if i put for silent mode i can fell the vibration so what the problem in my phone

my iphone 3gs shows white screen i restored it in itunes then to same problem once i connect my phone to charge i can hear the sound and if i put for silent mode i can fell the vibration so what the problem in my phone

Here is what you should do turn the device on hold the home button and the power button until the device turn off keep holding and when the device reboots release the power button but hol the home button until it shows the iTunes logo then restore it

ISE dACL for FlexConnect AP

hello all,
I found a similar thread, but it didn't exactly answer my question:
https://supportforums.cisco.com/discussion/12114056/flex-connect-user-acl-aps-locally-switched
Should I configure a regular ACL, or Airespace ACL on ISE, to support FlexConnect mode AP's?
On the FlexConnect AP's (WLC), do I configure a regular ACL, or FlexConnect ACL?
The FlexConnect AP's are running a few SSID's, some are centrally switched, and some are locally switched.
Thanks,
Kevin

It depends which version of WLC, v 7.4.110 has a bug (Unfortunately, I don't remember the bug Id). You need to create a regular and FlexConnect using the same name. With recent version (I'm using 7.6.130), you don't need the regular ACL, just a FlexConnect ACL. So, to answer your question, with FlexConnect, you must use FlexConnect ACL.
Good links:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_010001110.html
http://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/116143-config-cise-posture-00.html

Direct material procurement in PDP scenario for classic mode

Dear Gurus,
We have configured classic scenario in our SRM 7.01 with backend system ECC 6.0 Enhpk 5. We have PDP scenario for direct material as one of the requirement. The requirement generated in MRP in the ECC backend system will be sent to SRM SOCO for sourcing. Once the right source of supply is found, the follow-on purchase order needs to be created in the ECC backend system in direct material mode.
However, the SAP SRM standard supports only indirect material procurement in PDP scneario for classic mode. How to enable the direct material procurement? Could you suggest any BAdi to be used here?
Thanks and regards,
Ranjan
Ranjan Sutradhar

Hello,
You need to activate the Bsdi 'ME_REQ_SOURCING_CUST' for transferring the purchase requisitions from ERP to SAP SRM.
Some details about the method involved for the same are mentioned below :
Mehtod : IF_EX_ME_REQ_SOURCE_CUST~ACTIVE
->when parameter CV_AUT_SOURCING is set to true, external sourcing (e.g. SRM system) is active in ERP system
->when parameter CV_EXT_RFX_IND is set to true, RFx can be created out of PR directly from ERP system using application CPPR
->when parameter CV_EXT_SC_IND is set to true, PR in ERP system will be transferred to SRM using application CPPR
Method b. IF_EX_ME_REQ_SOURCE_CUST~CHECK_EXTERNAL_SOURCE
Here you need to maintain the logic / condition for which PR has to be transfered to SOCO.
Example
IF ( is_req_item-ekgrp = 'SRM' AND is_req_item-matkl = '100' )
cv_ext_sourcing = cl_mmpur_constants=>yes.
ENDIF.
When this BADI is active whenever you save a PR with say the purchasing group as SRM and material group is 100 (as per sample code above), system automatically triggers the PR transfer from ERP to SRM by xml's.
Best Regards,
Rahul

AP in Flexconnect mode not registering automatically to WLC after Link Up

Hi,
I have 2702I series AP registered with 5508 HA WLC over WAN working in Flexconnect mode. All of a sudden the AP lost connectivity to WLC and is operational in Flexconnect mode now.
I am concerned whether it should rejoin again automatically ?(which didn't happen) or i need a reboot to get it joined again.
Also if it rejoins automatically does the wireless services go down ?
Any specific reasons to why it didn't register ? Have debugged capwap and saw error unable to resolve CISCO-CAPWAP-CONTROLLER. Not sure why its unable to resolve now as earlier it was registered this way only.
Any suggestions ??
Thanks
Rahul

The FlexConnect access point should register back to the controller that was defined as the primary, secondary and or tertiary controller or one of the other controllers in the mobility group. I would make sure that the AP hasn't joined any other controller. If you are able to console into the access point, then you can really see what is happening. Seems like you were able to either console or ssh to that AP.
You still have other access points that have joined the controller? Is this the only access point that id in standalone mode at the momen? I would try to reboot it and see what happens, but its best to have console access.
-Scott

PO for change mode

Hello Gurus,
I have successfully done with PO workflow for create mode..now i have to create this PO wf for change mode too,
so my question is should i create a different wf by taking different event for change mode, or is there any other way to do change PO wf with this create PO wf.
Any help please??
Kind Regards,
Him joshi

Just check how your workflow is linked ro event which is triggered when the PO is created.
Similarly you can have another event when the PO is chnaged and set this vent in the triggering event section of the current workflow. So when this new event is triggered this same workflow will get triggered.
Its totally depend on you how you want to trigger the workflow.
similarly you may have to consider the case what if the po is created and a workflow is triggered abd yet to complete and at teh same time sone one chnaged tht PO, should it trigger new workflow or exisiting workflow is looped back.

Multicasting for Flexconnect mode

Similar Messages

Maybe you are looking for