Multilink limitations application on Cisco 7200 Series

Hi,
Can someone please mention if Multilink can be supported on Cisco 7200 Series?
IOS version:
IOS 7200 Software (C7200-P-M), Version 12.3(16a), SOFTWARE (fc2)
cisco 7206VXR 
Any comment will be appreciated.
Thank you.

Hi -
Our s/w development group is in the process of implementing ipv6 support in our products, and would like to use our Cisco 2650XM running ITP s/w for ipv6 interoperability tests.
However, it appears that ipv6 is not supported in this s/w version:
ITP1#sh version
Cisco IOS Software, C2600 Software (C2600-ITPK9-M), Version 12.4(15)SW2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Tue 23-Sep-08 19:48 by prod_rel_team
ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
ITP1#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
ITP1(config)#ipv6 ?
% Unrecognized command
My question is: Can I use this s/w version on the 2650XM in an ipv6 network? Do I need to upgrade the s/w?
Thanks,
Matt

Similar Messages

  • Problem with 7200 Series

    Hi All
    I have a 7200 series Router and I have just had a wierd crash...
    Debug from console @ crash time attached below - Any ideas ???
    Thanks
    Malcolm

    Hi, don't take this as a personal critique, but a bit more information about what a "new version is" would be beneficial for your organization.
    You have 12.3 T in which new features are introduced version after version. At some point the process stops and the result is called 12.4 in which very limited features are introduced. Then by testing or whatever other method cisco decides that 12.4(3j) is the the most suited for general use and in fact it is what the new routers are shipped for. the j means that there have been a-b-c-d-e-f-g-h-i releases before, each one consisting of bug fixes only.
    So, using that on a router is a safe choice and not a "big version change".
    In my experience I've seen that many times, customers exithating in upgrade, getting the consequences of bugs in the meanwhile.

  • Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

    Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
    and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
    My questions are How do you direct this utility to point to the desktop or the TFTP folder
    does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
    My router is suppose to have 10.0.0.3 255.0.0.0
    Gateway of 10.0.0.1 255.0.0.0
    My TFTP Server 10.0.0.2 255.0.0.0
    How do I get the MAC address of the Router or the TFTP Server and which one  is required?
    my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
    =====================================================================================
    rommon 10 >
    rommon 10 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    ?=0
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    TFTP_FILE=
    rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    rommon 12 > TFTP_CHECKSUM=0
    rommon 13 > SET
    monitor: command "SET" not found
    rommon 14 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    ?=0
    TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    TFTP_CHECKSUM=0
    rommon 15 > tftpdnld
              IP_ADDRESS: 10.0.0.3
          IP_SUBNET_MASK: 255.0.0.0
         DEFAULT_GATEWAY: 10.0.0.1
             TFTP_SERVER: 10.0.0.2
               TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
            TFTP_VERBOSE: Progress
        TFTP_RETRY_COUNT: 18
            TFTP_TIMEOUT: 7200
           TFTP_CHECKSUM: No
            TFTP_MACADDR: 30:37:a6:49:35:a8
                 FE_PORT: Fast Ethernet 0
           FE_SPEED_MODE: Auto
    Invoke this command for disaster recovery only.
    WARNING: all existing data in all partitions on flash: will be lost!
    Do you wish to continue? y/n:  [n]:  y
    ARP: address resolution for 10.0.0.2 timed out.
    ARP failed with failure code 1.  TFTP transfer aborted.
    TFTP: Operation terminated prematurely.
    rommon 16 >       " not found
    rommon 17 >FE_SPEED_MODE=2
    variable name contains illegal (non-printable) characters
    rommon
    rommon 18 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    TFTP_CHECKSUM=0
    ?=0
    rommon 19 > tftpdnld [ur]
    usage: tftpdnld [-hr]
      Use this command for disaster recovery only to recover an image via TFTP.
      Monitor variables are used to set up parameters for the transfer.
      (Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
      "ctrl-c" or "break" stops the transfer before flash erase begins.
      The following variables are REQUIRED to be set for tftpdnld:
                IP_ADDRESS: The IP address for this unit
            IP_SUBNET_MASK: The subnet mask for this unit
           DEFAULT_GATEWAY: The default gateway for this unit
               TFTP_SERVER: The IP address of the server to fetch from
                 TFTP_FILE: The filename to fetch
      The following variables are OPTIONAL:
              TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
          TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
              TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
             TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
              TFTP_MACADDR: The MAC address for this unit
                   FE_PORT: 0= (default), 1
             FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                            5=Auto (default)
          TFTP_DESTINATION: The flash destination device for the file
                            flash:(default), usbflash0:, usbflash1:
      Command line options:
       -h: this help screen
       -r: do not write flash, load to DRAM only and launch image
    rommon 20 > tftpdnld
              IP_ADDRESS: 10.0.0.3
          IP_SUBNET_MASK: 255.0.0.0
         DEFAULT_GATEWAY: 10.0.0.1
             TFTP_SERVER: 10.0.0.2
               TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
            TFTP_VERBOSE: Progress
        TFTP_RETRY_COUNT: 18
            TFTP_TIMEOUT: 7200
           TFTP_CHECKSUM: No
            TFTP_MACADDR: 30:37:a6:49:35:a8
                 FE_PORT: Fast Ethernet 0
           FE_SPEED_MODE: Auto
    Invoke this command for disaster recovery only.
    WARNING: all existing data in all partitions on flash: will be lost!
    Do you wish to continue? y/n:  [n]:  y
    ARP: address resolution for 10.0.0.2 timed out.
    ARP failed with failure code 1.  TFTP transfer aborted.
    TFTP: Operation terminated prematurely.
    rommon 21 >

    What I notice in the original post is this error
    ARP: address resolution for 10.0.0.2 timed out.
    which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
    HTH
    Rick

  • What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier

    What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier
    These items are listed with 1600 series AP but I'm unable to understand what are these things & the use of them

    DHCP Option 60:  Go HERE.

  • How to bridge a linksys cisco E1200 series router?

    I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox

    purchase 881w, get rid of linksys. That should do it.
    Sent from Cisco Technical Support iPad App

  • Need a tool for flash backup on Cisco 2821 series routers

    Hello Folks,
    We have around 1200-1500 cisco 2821 series routers on those we are performing the hardware upgrade so we are taking the backup of all the files available in the flash of all the routers, we just want to know is there any trusted tool available to make this task easy to schedule and take the backups.
    Please let me know if you know any tool name.
    Thanks,
    Raja.

    Sorry, I don't know any tool that makes a backup of the whole flash...
    You could fo it with from ios cli maybe execute it automatically...
    To flash:
    archive tar /create flash:/backup.tar flash:/
    copying directly to ftp should also work:
    archive tar /create ftp://test:[email protected]/backup.tar flash:/

  • What hardware is required to activate application like Cisco Unity Connection ?

               Please I need your help,
    What hardware is required to activate application like Cisco Unity® Connection ?
    Thank you       

    In addition to great reply (+5), basically this is similar to CUCM which you need to have in order to run Unity Connection (or you could have CME).  So, if you have CUCM running it will be very similar concept. If this is new install you want to definitely go the virtual path.
    HTH,
    Chris

  • Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

    Hi All,
    Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
    Any help would be greatly appreciated.
    Thanks in advance.
    Samir

    Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices.  RME will only use HTTPS to fetch VPN concentrator configurations.

  • Can I terminate 40 Mbps DSL BROAD BAND connection in Cisco 800 series routers

    Dear all,
     Can I terminate 40 Mbps DSL BROAD BAND connection in Cisco 800 series router?.It is not a leased line.
    Which Router model is best for 40 Mbps DSL Broad band termination ?
    Thanks&Regards
    Ajay Jose K

    Hi , 
     Below link provides you all model in 800 series . 
    http://www.cisco.com/c/en/us/support/routers/800-series-routers/tsd-products-support-series-home.html
    For your requirement below model should suffice . 
    Complete throughput from the router is 51 Mbps .
    Cisco C891FW Integrated Services Router
    HTH
    Sandy

  • Which command in the Cisco AP1200 series will you use to broadcast the SSID using VLANs?

    Folks,
    Which command in the Cisco AP1200 series will you use to broadcast the SSID using VLANs?
    Thanks

    If you have enabled mbssid, "guest-mode" would be replaced by "mbssid guest-mode" this would also allow multiple ssid's to be broadcast
    -Tim
    Sent from Cisco Technical Support iPad App

  • Error in Cisco 2500 series Wireless Controller

    I have this error in Cisco 2500 series  Wireless Controller 
    The AP type Cisco AIR-CAP35021-A-K9
    I cann't connect the client to AP when i try to connect i get this error on Cisco 2500 series  Wireless Controller  But the AP get ip .
    Please can any on help me . 
    Client Excluded: MACAddress:Base Radio MAC : Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 

    Duplicate posts.  
    Go here:   http://supportforums.cisco.com/discussion/12142556/cisco-2500-series-wireless-controller

  • Oracle RAC and Cisco 7000 Series

    Has anyone been successful with database 11.1.0.6 or 11.1.0.7 using a Cisco 7000 series router for the cache fusion interconnect.
    A simple yes, if you have done so, will be very much appreciated.
    We have a cluster that works with 5000 series switches and hangs with 7000 series ... trying multiple physical switches for the test.
    Thank you.

    It should work properly. One correction it should be switch not router. We have used the same.

  • Cisco MDS series switch details

    Hello I 'm new to CISCO  Switch world.
    I 'm working as Clariion Admin and have have taken up the responsibilty to manage switches.Since,i am a novice i need little guidance on how work on cisco switches.I know the Zoning (how zoning done on MDS 9000 series switches) part ,but would like to venture deep into the details on CISCO MDS series switches.
    Like, the use of Port channels etc.
    Will really appreciate if some one can help me with a link or place ( not the configuration guide) where in i can find details on concentrated more on the theory part .
    Thanks in advance!

    Actually the best info is in the configuration guides.  There are some external companies that run training sessions on the MDS to provide in depth training.  There is the MDS cookbook available on CCO that is also a good point of information.    If you search on 'MDS white papers' after you login into Cisco.com, there are several good documents that might meet your needs.
    Hope this hels,
    Mike

  • Cisco 4500 series switch

    Dear support taem, in cisco 4500 series switch i am getting error interface TenGigabitethernet 1/14 utlization threshold violated.current in traffic 705.228 (70.52 %) and out traffic 707.462 ( 70.75 %) whereas configured threshold is 30 %.
    i have checked on switch but qos is there in configuration.
    where i need to check if any restriction is there for incoming and outgoing traffic.
    and what necassery troubleshooting i need to be done.

    This looks like a policy shaping.

  • Cisco 4003 series switch

    Hi...All.
    In cisco 4003 series switch i m getting error in post test its says , rtc failed, after that supervisorengineer wxx4012 LED status is Red.can any one tell me wt that means and hw to solve that problem.

    plz fine the post test script...
    003-B-Ground> (enable) 0:00.523556: Please set IPAddr variable
    0:00.524147: Please set Netmask variable
    0:00.524511: Please set Broadcast variable
    0:00.525113: Please set TftpServer variable to do tftp downloads
    0:00.525658: Network is not configured
    WS-X4012 bootrom version 5.4(1), built on 2000.02.17 18:28:09
    H/W Revisions: Meteor: 4 Comet: 8 Board: 2
    Supervisor MAC addresses: 00:02:16:d2:5a:00 through 00:02:16:d2:5d:ff (1024 addr
    esses)
    Installed memory: 64 MB
    Testing LEDs.... done!
    The system will autoboot in 5 seconds.
    Type control-C to prevent autobooting.
    rommon 1 >
    The system will now begin autobooting.
    Autobooting image: "bootflash:cat4000.5-4-2.bin"
    CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
    CCCCCCCCCCCCCCCCCCCCCCCCCCC#############################
    Starting Off-line Diagnostics
    Mapping in TempFs
    Board type is WS-X4012
    DiagBootMode value is "post"
    Telling ApkPageMan that we have 12288 pages of memory
    Loading diagnostics...
    Power-on-self-test for Module 1: WS-X4012
    Status: (. = Pass, F = Fail)
    processor: . cpu sdram: . rtc: F
    eprom: . nvram: . flash: .
    temperature sensor: . enet console port: . switch port 0: .
    switch port 1: . switch port 2: . switch port 3: .
    switch port 4: . switch port 5: . switch port 6: .
    switch port 7: . switch port 8: . switch port 9: .
    switch port 10: . switch port 11: . switch registers: .
    switch sram: .
    Module 1 Failed
    Power-on-self-test for Module 2: not present
    Port status: (. = Pass, F = Fail)
    Module 2 Ignored
    Power-on-self-test for Module 3: not present
    Port status: (. = Pass, F = Fail)
    Module 3 Ignored
    Exiting Off-line Diagnostics
    Failed Module Bringup Process
    Use 'show test 1' to see results of tests.
    Cisco Systems, Inc. Console

Maybe you are looking for

  • Sales Opportunity number field

    In Open Items report (Sales Orders) is it possible to have column displaying Sales opportunity number that the sales order was created from? I have looked through form settings but cannot find this field?

  • How do i open a created project that is in a file?

    Hi all, How do i open a created project that is in a file in NWDS 7.2? I tried the below method: 1) created a dc 2) Import-->General-->filesystem-->proceeded further. But there was no project. What am I doing wrong? Regards, Manoj.

  • Airplay sound not via iTunes

    hello, I am not an expert in all those Airplay devices. I appreciate your help. I want to buy below Soundlink System with Airplay (just came out so no help so far online) and connect it to iMac and mobile devices. iMac can play music from this speake

  • REAL problems with iMessage activation same with Face Time

    I'm having real problems with IMessage activation same with FaceTime, the phone shows the activation is being made but it does not activate! Apple ID and password is OK, it's working with other applications Any ideas guys?!

  • Looking for a Dashboard Widget

    Is there a Dashboard widget that will notify me when I receive responses on message boards, like this one for example so I don't have to check email? Also, is there a good widget that can store my passwords for message boards as well? thanks!