Multiple Errors While Attempting to Sync

When I attempt to sync my 2nd generation iPod Touch (iOS 4) with my iTunes (v 9.2), I receive multiple errors: Can not copy song due to unknown error 0xE800400C, the device has timed out, and an internal device error occurred. I have tried just about everything, including:
- Restoring the iPod
- Uninstalling everything apple related and reinstalling iTunes
- Paying $99 for a replacement iPod
- Using a different USB device to hook it up
- I don't use any fancy add-ons, so there aren't any to remove
- Turned off my firewall
I can't find any other advice to use. Help!!

I wish I could be more specific on my answer, however I cannot find the original place that has the answer.
I think the two main fixes for this is
1: go to device manager and look under "universal serial bus controller"
1a: look for two "USB Enhanced host controllers" (make sure it has enhanced)
1b: if you only see one USB Enhanced host controller then move on to 2
1c: if you DO have two of these, then be sure you have access to a mouse that you can connect that does NOT use USB, or a track pad (such as on a laptop)
1d: disable one of the USB enhanced host controllers by right clicking it and hit disable, (this may cause and usb devices such as keyboards or a mouse to stop working)
1e: try to sync your ipod.
1f: if it fails enable that enhanced host controller and disable the other.
1g: if it works either either of these configurations great, though you may run into some corrupted applications if you have transfered purchases in the past, these will need to be deleted and redownloaded.
2. Update your bios, if you don't know how to do this you probably should not attempt it on your own. Perform any available windows updates, then call your computer manufacturer and ask them to help you do this.

Similar Messages

"Error while trying to sync Audio and Midi"

"Error while trying to sync Audio and Midi" I have been having this problem now and then for some time. Now, I can't run any audio files without a lot of popping. I tried all the suggestions on the support document for this issue. I even downloaded new drivers from Motu for my Express XT Midi interface and my 828MK11 Audio interface. There has been no change. HEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEELP!!!!!!
Also, I have tried reseting the 828 to factory default and that does not help.
Jonathan Jenkins

Hi,
I solved my own problem by resetting the factory presets:
Follow these steps to restore the MOTU 828mkII to Factory Default Settings.
Disconnect the firewire cable from the 828mkII
Press the Setup knob
Turn the Setup knob all the way to the right
Press the Select knob
Press the Value knob
Power off the interface and plug the firewire cable back in
Power the interface back on
The same steps can be followed to restore the Factory Default Settings on a Traveler.
-Robert

Pop up saying error while trying to sync audi and midi

HELP! is there anyone who is experiencing or has experienced an error pop up saying error while trying to sync audio and midi in your logic pro8? it's doing it on every song I pull up now. I've tried buffering, reloading, Help? all was fine the night before.
Sincere, The Silver Conductor

Check the clock source on your audio interface if you're using one. It should be set to internal. What's your setup?

Getting multiple error while refreshing or scheduling WebI report

Hi BO Admin Experts ,
Feacing multiple errors while refreshing or scheduling webi reports in BI4.0 CMC ,
Please find the below errors :
1)report schedule status failed
2)Parameters : xxxcorp-franklinee; ATOu supply unv
Error Message : An internal error occured while calling 'ProcessDPcmndsEx' API (Error:ERR_WIS_30270)
3 ) Format : WebI
Parameters : 10000000000159270
Error Message :CORBA error while communicating with the SL service
Could you please help me on the abive 3 issues for the WebI schedule reports
Cheers ,
Pradeep Gorpadu

Hi,
While refreshing the WEBI Reports would recommend you check the WEBI PROCESSING Server's last changed date from CMC--> Servers.
Check when you are refreshing the reports, do you see the time stamp changed of WEBI PROCESSING servers?
Do you keep getting this error messages for all WEBI reports? Can you re-produce this with simple e-fashion reports as well?
After that go to the node where WEBI PROCESSING servers installed and check on the event viewer details if you see any relevant error messages.
Regards,
Upendra

Event ID 1012 - There was an error while attempting to read the local hosts file

When I start my Computer after it has been turned off overnight (switched off at the Power supply) I get a Blue screen and have to reboot the PC. in the Event log it has this error: Event ID 1012 - DNS client events - There was an error while attempting
to read the local hosts file.
Once the PC has booted evrything is O.K. I can restart the PC with no problems, it only seems to happen if the PC has been switched off for a while.
I am connected to the net via an Netgear dg834v4 Modem/Router
Windows 7 Ultimate
Intel Q8200 CPU
2 x 360 Gb HDD
ATI 4680 !Gb Video Card
Digital HDA X-Mystique 7.1 Sound Card
Aver media 777 TV Tuner card.
Thank you
jeepers01
After further Investigation it seems that this error is Not responsible for my Blue screening......I started my PC after leaving it off all night, and it started normally, but i still have this error in the Event Log - System.....I have searched the Technet
forums (and there is a lot of ID 1012 errors) but non relating to my problem....If anyone knows what is causing this error and how to fix it, i'd be Grateful....although it does not seem to affect the PC in any way that i can see.
thanks
jeepers01

Since Windows system uses separated user mode and kernel mode memory space, stop errors are always caused by kernel portion components, such as a third-party device drivers, backup software or anti-virus services (buggy services).
The system goes to a BSOD because there is some exceptions happened in the kernel (either the device driver errors or the service errors), and Windows implements this mechanism: When it detects some errors occur in the kernel, it will kill the box in case
some more severe damage happens. Then we get a blue screen or the system reboots (it depends on what the system settings are).
To troubleshoot this kind of kernel crash issue, we need to debug the crashed system dump. Unfortunately, debugging is beyond what we can do in the forum. A suggestion would be to contact Microsoft Customer Service and Support (CSS) via telephone so that
a dedicated Support Professional can assist with your request. Please be advised that contacting phone support will be a charged call.
To obtain the phone numbers for specific technology request please take a look at the web site listed below:
Microsoft - Help and Support
If you are outside the US please see
Microsoft Worldwide Home for regional support phone numbers.
Meantime we can try some available steps as a general troubleshoot.
1. Please remove the antivirus and run the system with a period. If the issue does not occur, mainly focus on antivirus settings and compatibility.
2. Disable Automatic Restart and see detail information on the blue screen.
1).Click Start, in the Start Search box enter sysdm.cpl.
2).Click the tab Advanced. Under Startup and Recovery, click the Settings button.
3). Uncheck “Automatically restart”.
4). On the drop-down menu “Write debugging information”, choose “Small memory dump”.
5). Click OK.
When Blue Screen displays, you may find some useful information.
Arthur Xie - MSFT

Get-mailboxdatabasecopystatus -identity DBNAME | fl gives errors "The Microsoft Exchange Replication service encountered an error while attempting to start a replication instance for". DB is mounted and the DB copies are in healthy status.

We are getting a SCOM alert " Database copy isn''''t keeping up with the changes on the active database copy and has failed."
When we go to the mailbox server and check we found all the Mailbox DB's are mounted properly and their copies are in healthy state. Further digging to this problem we found that there are no critical events to this DB in the eventviewer.
When we runt he get-mailboxdatabasecopystatus -identity DBNAME | Fl then in the ErrorMessage section we get error "The Microsoft Exchange Replication service encountered an error while attempting to start a replication instance for . If the copy doesn't
recover automatically, administrator intervention may be necessary. Error: The directory is not empty."
ErrorEventID : 4126
In the event viewer we get a Information event 4114 saying the DB redundancy health check passed and in the details section we get the same error message mentioned above.
Also we observed that the "MSExchange Replication" counter "Failed" is set to 1 for this perticular DB but is is set to 0 for the other DB's. Tried restarting the MSEXChange replication service but still the "Failed" counter
is 1 and the SCOM alert is still active.
The version is Exchange 2010 SP3 UR5
Any clues???

Hi,
From your description, this issue only affect one mailbox datatabase.
Please use the Update-MailboxDatabaseCopy command to check result.
If it doesn't work, please dismount your active database copy and check if this is Clean Shutdown, if it's dirty shutdown, please bring to clean shutdown and mount this database copy. Then run the Update-MailboxDatabaseCopy command again to check result.
Best regards,
Belinda Ma
TechNet Community Support

I have using I phone 5c after connected with my HP elite book 6930p laptop, Automatic software driver is not deducting, and display Windows found driver software for your device (MTP USD Device) but encountered an error while attempting to install it.

I am using I phone 5c after connected with my HP elite book 6930p laptop, (Installed Window 7 32 bit). automatic software driver is not deducting, and display Windows found driver software for your device (MTP USD Device) but encountered an error while attempting to install it.
I did install itunes and update also. but the above problem still same.
Kindly give me solution of it. awaiting.
Regards
Abbas Kader

try it with another computer to check if it shows up
if so
uninstall all apple software
reboot
use regedit to search and remove all itunes keys
reboot
resinstall apple software
if non of that helps then try another cable
if that don't help could be your phones connector is damaged

What are solutions to the "Unexpected error while attempting to bind. Operation cancelled." message when trying to bind

What are solutions to the "Unexpected error while attempting to bind. Operation cancelled." message when trying to bind and i alreeady cheack my DNS settings and everything

Has this worked before, or is this a new configuration?
On the server, launch Terminal.app from Applications > Utilities and post the output of the following harmless diagnostic command — and you'll need to enter an administrative password when requested:
sudo changeip -checkhostname
On the OS X (presumably) Mavericks client, please post the IP address(es) of the DNS server(s) you're referencing. These are available via the System Preferences > Network > Advanced > DNS settings.
To check the console logs, launch Console.app from Applications > Utilities on both the client and the server, and then attempt the binding, and then post a (short! no more than ~25 to 50 lines!) of any errors related to the binding error.
If you're not in a position to post configuration details here — which is perfectly reasonable, and entirely your prerogative — or if I'm getting too confusing or too technical with some of the questions here, which would be my error of course — then (assuming these systems are under warranty) I'd suggest contacting the folks at the local Apple Store and having a chat with the local Geniuses about this, or checking directly with the Apple Support folks via telephone.

IWocountered an error while attempting to create the attachment data.

Hi I have created an invoice on pages,then saved it.
When i click on share to send document via email as a PDF file this message comes up "IWORK ENCOUNTERED AN ERROR WHILE ATTEMPTING TO CREATE THE ATTACHMENT DATA" can anybody help it very frustrating,i recently wiped my mac book pro and since i put iwork back on it hasnt worked.
Thanks Tasha

Pages 5 has a complex and unique file bundle format. Designed to make it impossible to extract any contents when the inevitable goes wrong.
GMail, Amazon, Dropbox etc (almost any non-Apple Server software) just don't understand them.
Send the files via Apple Mail.
Peter

Error: SharePoint Workspace encountered an unknown error while attempting to create this list

Hi,
I am using Sharepoint workspace to offline synchronize a document library.
In the workspace, I provided the site name. All but one document library was downloaded.
I selected the document library, which did not get downloaded. I am getting the below message:
SharePoint Workspace encountered an unknown error while attempting to create this list. Ask your site administrator to resolve the issue and then click Resolve Error in the Resolve tab.
If I click on Resolve error, the sharepoint workspace crashes and opens again.
How to fix this?
Thanks

Hi,
For troubleshooting your issue, you can take steps as below:
Running groove.exe /clean from command prompt
Running groove.exe /clean /all from the command prompt
Removing the library from sharepoint workspace and re-adding it
Deleting the users folder from c:\users\username\appdata\local\microsoft\office\groove\user
Running a repair on Office 2010
Uninstalling and reinstalling the Sharepoint Workspace tool from the computer
Verifying all updates are installed
Reference:
https://support.office.com/en-in/article/Resolving-conflicts-and-errors-in-SharePoint-Workspace-70928d16-1cff-4931-b693-f5e346a7bf99?ui=en-US&rs=en-IN&ad=IN#bm1
Best Regards,
Eric
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

"Error while attempting to save event log" On VPN3000

My VPN have started to e-mail the following problem.
54438 03/29/2008 14:55:06.660 SEV=2 EVENT/14 RPT=288
Error while attempting to save event log (operation: fopen, code:
Anybody have any idears, I have tried to reboot but need not fix anything.
When I try click on "Save Needed", I get the following errror "Unable to Save
File Write Error".
I can see that my event log is getting updated with other stuff like "IKEDBG/79" - "Phase 1 failure against global IKE proposal".

Try re-naming the existing files, and then do the save. I had a similar problem, and I think it was a corrupt file that the system could not overwrite, but could rename. Then you can delete the old one.

My pc froze while attempting to sync iphone4 and now cant turn it off? any ideas on what to do next??

my pc froze while attempting to sync iphone4 and now cant turn the phone off? any ideas on what to do next??

Try the following:
1. Reset: Hold the Sleep/Wake and Home button down for about 10 seconds until you see the Apple Logo.
2. Restore:
http://support.apple.com/kb/HT1414
3. Recovery:
http://support.apple.com/kb/HT1808

Error while installing PIM Sync

Hi,
While installing PIM Sync an error is given
"Installation found another product installed which uses the same configuration file settings. Installation was cancelled because they cannot function on the same computer. Please uninstall the other software first."
But there is no software installed related to CRM.
Please help.
Thanks
Arpita.

Hi Arpita,
Sometimes it happens all the files may not be removed ,even if you have removed it.
Please follow the below steps to remove it
Under certain conditions, an uninstall process does not completely remove all references to the PIM Sync client on a users system.
When this occurs an new installation sometimes produces an error message that says something like "unable to complete the install since there is already a previous version installed, remove the previous version and attempt the install again".
If this error appears you can try the manual removal of a registry entry that refers to the previous install of the PIM Sync client. Follow these steps to remove the necessary registry entry on the machine:
1. Click Start>Run and enter "regedit" to open the MS Windows Registry editor
2. Locate the following registry entry
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\{8DB1D80B-580E-48EE-A259-226108CF6308}
Thanks,
Srinivas Merugu

Error while running Background Sync for User, Roles

Hi All,
I get the below errors when i am scheduling background jobs for User and Role Sync
We have connected another system APO to GRC, we already have ECC running
for the APO system we used the connectors VirsaXSR3_01 (Metadata, model) for this
Any ideas why they are failing
Error while executing the Job:Interface Controller does not exist for Component Instance VirsaXSR3_01 in Component Usage VirsaXSR3_01
Error while executing the Job:type com.virsa.cc.modelvirsaxsr3_01.types.So_Text001 could not be loaded: com.sap.dictionary.runtime.DdException: TypeBroker failed to access SL
Thanks

Hi All,
Thank you for your inputs, but i figured out the issue with the error,
Our basis folks actually made the mistake creating JCO's
They created VIRSAXSR3_02_METADATA & VIRSAXSR3_01_MODEL instead of VIRSAXSR3_01_METADATA & VIRSAXSR3_01_MODEL
this has been rectified and my background jobs run fine now.
Thanks

Error while configuring AAD Sync

Hello Experts,
I have one of my customer encountered with issue while configuring AAD Sync tool.
Below is the error message
"An error occured executing Configure AAD Sync task:unable to establish a connection to the authentication service"
Appreciate if any one could help in resolving the above error.
Thanks everyone.

Hello,
Can you give us more information, a log file for example?
The username/password that you use work?
Florent

Multiple Errors While Attempting to Sync

Similar Messages

Maybe you are looking for