Multiple instrument tracks routed to ONE instance of Kontakt?

I've got a Kontakt 3 sampler fully loaded with different instruments, routed to separate midi channels. But I can't seem to figure out how to assign multiple midi tracks in the arrange window to these separate instruments within Kontakt! In Cubase this is easy when you can actually chose one of the active VSTi's when you select an instrument for a midi track, what is the corresponding way in logic?
Thanks!!
/Erik

Well if you do it right it will create a Multitimbral instance of Kontakt....
hit "+" ->Software Instrument-> check the box "Multitimbral" - choose amount of Midi channels->read the manual...

Similar Messages

  • How do you use only one plugin in Logic for multiple guitar tracks? I want to only use one instance of Pod Farm and run all my guitar tracks through that one instance.

    I want to be able to use only one instance of Pod Farm for my guitars, and have all of my guitar tracks run through it while I'm recording.

    What he said. Or here is a similar approach with a picture.
    1. Press the SEND button on every stereo (or mono) guitar track you want to send through the effect. Then select a free bus.
    2. Make sure you turn up the amount of send (in db). Holding alt while leftclicking on this circle sets the send level to 0 db wich is good.
    3. Open the mixer (Cmd+2). Please see that I here have turned the output off from the stereo guitar track. That way the only output will be the BUS, in your case the AmpTrack bus where all your guitars will pass through. If you want both the original guitar sound AND the Ampfarm effect then just set all outputs on your guitar tracks to Stereo Out, like the AmpF Bus track is set in my picture.
    4. Insert your AmpFarm plugin here. I don´t have that plug so I inserted Waves Renes Axe for demo purpose.
    Adjust the volume/effect of every guitartrack by turning the circle input shown as 2. in my picture.
    I now see that you mentioned Pod Farm, not AmpFarm. But I guess it´s the same trick.
    Have fun.
    Heyclown.
    Message was edited by: WizardSongs - Typhoos

  • Instrument track only plays one track at a time

    Logic Studio will only play one instrument track at a time. Whenever I click to another instrument track I lose the sound. The channel strip meter still shows that the instrument is playing but there is no sound. When I click back on that channel strip I can hear the sound again. Although the channel strip meter works, the strip in the mixer doesn't show any signal at all. It seems that the track is working but there doesn't seem to be any output to the mixer. I have checked all of the solo buttons and none are on. I opened a blank project and all of the software instruments worked just fine; it is only in this project that I can't get more than one instrument track to play at a time.

    still plays only one instrument track at a time
    I think this project might be damaged, and it would be great if we could take a look at it, as Bee Jay suggested. In the meantime, you should try what Erik suggested about option-click. And here are a few other ideas, although I'm not too optimistic.
    Select any region and press S. Three things should happen: this region should have a yellow outline, the ruler should turn yellow, and the solo button in the transport bar should turn yellow. Press S again, and those three things should revert to normal. Is this what happens? It just might be helpful to know.
    In the Mixer window, find the button at the top that says "All," and select it. Make sure to look at every channel strip. No yellow S button anywhere? Do you see any Mute buttons flashing?
    Press option-K to open the key commands window. In the search box, type "solo off" (without the quote marks). You will see the command 'Solo off for all.' Probably no key is assigned. Give it a key (option-1 might be a good choice, because it's probably available). Close the key commands window, and press the key stroke. Better now?
    The channel strip meter still shows that the instrument is playing but there is no sound. When I click back on that channel strip I can hear the sound again. Although the channel strip meter works, the strip in the mixer doesn't show any signal at all.
    I have a feeling that when you say "channel strip meter" you mean 'track header meter.' Because it's completely normal that when a midi track is muted (e.g., because another track is soloed) that the track header meter will keep lighting up, even though there's no sound and even though the meter in the mixer (on what is properly called the channel strip) is dark.
    The meter in the track header is just indicating that Logic is reading midi from the track. Whether or not that midi gets to become sound is something that happens downstream, and is not reflected in this meter.

  • Multiple arrange tracks for the same instance of a plugin?

    Is this possible?  I am using DMXIS, a DMX lighting plugin. It's great but I need to run dozens of tracks of automation at the same time. I know I can drop down as many automation tracks as I want but it is confusing that their labling does not reflect the tasks I have given them. Instead of the automation track reading "channel 76", I want it to say "red light, stage right" or whatever. It would help me enormously if I could have a single track, labled differently, for each automation task. Or, almost as good, Can I change the names of the plugin paramaters, as they apear in the automation, so that they tell me what I want to know rather than the name the plugin has given to each paramater?

    Yeah I got used to being able to add multiple listeners from working with ActionScript 3 and it was a bit off-putting when I noticed the same feature was not in JavaFX. Thankfully I have not yet been blocked by this issue, but it seems if I was I could get similar functionality by creating a mixin class that stores a map of Sequences of functions by event type. This mixin would also have a function to call all the functions for a given event in order. Then you could just have your event target class extend the mixin and assign the event chaining function as your event function. This gives you a way to add / remove event functions through the mixin interface and not have to know about the specific type of your target.
    The situation complicates when you want all the stuff that comes with a full-blown event stack like being able to cancel propagation, etc., but you could also implement these things with a bit more effort

  • Multiple MIDI tracks to one instrument?

    The plugin is Ultrabeat.
    I like putting the kick onto one MIDI track
    the snare into another MIDI track,
    hats on another, etc....
    Problem is, all of the MIDI tracks that route to the Ultrabeat
    are the actual instrument track that has the plugin inserted onto it.
    So MUTING one track mutes all the audio coming out of
    the Ultrabeat Instrument track.
    An attempt at a workaround is: create a Multi-instrument
    in the Environment, and connect it to the Ultrabeat.
    But then MUTING the MIDI tracks doesn't do anything.
    The MIDI tracks play even when MUTED.
    So I'm guessing Region Muting is the way we do it?
    Selecting individual regions for muting and solo-ing
    instead of muting and soloing the track ?
    So..the MUTE button on a MIDI track is there for...NO REASON.
    It's just a button that doesn't do anything.
    Well.. this MIDI track has muted and non-muted regions on it.
    I guess I'll need to remember which ones are muted and which
    are not ?
    This couldn't possibly have been something that was thought over
    and planned.
    Nobody in their right mind would design it this way on purpose.
    A solution would be to allow MIDI tracks to be MUTED using the 'M' button

    Are you talking about MIDI track on external MIDI?
    your question seems to be related with Instrument tracks...
    there many Muting possibilities in Logic...
    I suggest to read the manual serch for "mute track"
    As you can see in the manual there are tons of pages and paragraphs about MUTE function in Logic Pro... so I cannot explain all the way to MUTE a Midi or Audio
    I can only say that Instruments tracks are not the same as External MIDI track device... *but Muting Instrument track is very similar as Audio and Midi mixed together functions*
    'cause the Instruments channels strips are AUDIO CHANNELs STRIPs!
    Maybe the following pictures can help
    Try to change setting with the one shown below
    CPU-savings is not the correct therm and maybe this is caused of misunderstanding...
    this set allow you to individually mute the duplicate tracks...
    _+The "M" button that you are metioned in your post will works as you need.+_
    I'm trying to replay to the O.P question
    multiple MIDI tracks to one instrument?
    if you need to mute individually tracks of a single instrument the last pictures shows the best setting to achieve the result that you are looking for.
    G

  • 2 midi tracks routed through the same instrument instance

    Hi folks,
    I'm a new Logic user, and I expect this is a pretty stupid question but it's completely stumped me. Is it possible to route 2 (or more) midi tracks through the same instance of a virtual instrument? I am running Logic 8.02 with BFD2, and I'm trying to lay down a drum track bit by bit. On my first midi track I've finger-drummed a bass and snare pattern and I now want to add a hi hat and cymbals. I'm using the same kit, so there should be no need to open another instance of BFD2. I could record onto the existing track, but ideally I'd like to keep each drum / cymbal on a separate track.
    Any help would be much appreciated!
    Cheers.

    To add to what SC said, one concept that gets missed by new users is that any track and be assigned to any environment object.
    So if you have an arrange track that's currently assigned to audio channel 1, you can control-click on it, select "Reassign track object" and choose a different audio channel 1.
    So you can have as many tracks as you want all assigned to the same audio object, and this is a killer feature in Logic many people rely on, and that other DAWs don't tend to have.

  • One instance of Space Designer for multiple instruments

    Hi - I know that if you have - for example - four instances of an instrument all using the same Space Designer setting, you can have just one instance of the SD and use buses to send all the instruments to the same - somewhere - so they can all use it.
    I've tried this but I obviously placed the SD in the wrong -somewhere - since they didn't find it.
    Where is the correct place ?
    Thanks -Kay.

    Yes, that's the way to go.
    It is a shame, by the way, that names assigned to Busses in the I/O labels dialog are global to all Projects, so if you go crazy at one time and use *and name* 17 Busses for parallel compression, this naming is reflected in all other Projects too. Also, configurations in older Projects ported from V6,7,8 will vary wildly as you have refined your Templates, shifted gear, sold hardware etc. over the years. I have recently worked on a Project started in 2003, and Bus names were all over the place. It is one thing to have indifferent Bus 13, Bus 14, Bus 15 shown in the Sends, but it's a whole other dimension when all the names are wrong like Guitars, Vocals, Moreme when actually they feed Delay 1, Headphone and Drums.
    You can, however, work around this limitation. After copying the *IO Labels* file from User/Library/Application Support/Logic to a safe place like +Default IO Labels+, you can change the original to your liking and then copy that to your Project folder. This way you can throw the correct file back into the AppSupp folder when you're working on that Project later. You have to restart Logic for this to take effect.
    Christian

  • Keynote- Can you add multiple sound tracks to one presentation

    Can multiple sound tracks be added to the same presentation? For instance, can I add one sound track to play for slides 1-20 and a second, different sound track to play starting at slide 23 thru 36?

    Jonathan:
    You can create a single Story from each track and set the End Jump for each Story to the next one. Set the End Jump of the last Story to your menu and assign the first one to your PLAY ALL button.
    Give it a try !
      Alberto

  • Multiple Logical Systems in Partner Profile for one instance

    Can we create multiple Logical Systems in Partner Profile (WE20) for one instance or one System?  If it is possible, can we create Logical System with respect to Plant/Country?

    I am not quite sure if I understood your problem completley. But let's see...
    Usually you use on on MSCS Cluster Group per SAP instance. So you have your already existing NW 7.0 ABAP stack in a separated Cluster Group, and you create a new Cluster Group for your new Java system.
    You can find more information about it in this guide here on SDN:
    Link: [High Availability;
    More information about High Availability Setups for SAP System can be found here on SDN:
    Link: [High Availability]
    If you want to use the same database for your clustered ABAP stack and your new Java stack you can do a MCOD installation.
    Please see Link: [SAP Note 388866 - Multiple Components on One Database - Installation|https://service.sap.com/sap/support/notes/388866]
    Hope this helps.
    Best regards,
    Mathias

  • Can one instance have multiple redo threads ?

    i was reading the Oracle Data guard 10g guide and it says
    Determine the appropriate number of standby redo log file groups.
    Minimally, the configuration should have one more standby redo log file group than the number of online redo log file groups on the primary database. However, the recommended number of standby redo log file groups is dependent on the number of threads on the primary database. Use the following equation to determine an appropriate number of standby redo log file groups:
    (maximum number of logfiles for each thread + 1) * maximum number of threads
    Using this equation reduces the likelihood that the primary instance's log writer (LGWR) process will be blocked because a standby redo log file cannot be allocated on the standby database. For example, if the primary database has 2 log files for each thread and 2 threads, then 6 standby redo log file groups are needed on the standby database
    while Oracle's definition of redo log states the following
    Redo Threads
    When speaking in the context of multiple database instances, the redo log for each database instance is also referred to as a redo thread. In typical configurations, only one database instance accesses an Oracle Database, so only one thread is present. In an Oracle Real Application Clusters environment, however, two or more instances concurrently access a single database and each instance has its own thread of redo.
    this is confusing, in a typical environment where only one instance accesses a database, can we have more than one redo thread ?

    Though you can create multiple threads but of no use in NON-RAC or non-parallel server configuration.
    Following is the generic formula. You should consider
    maximum number of threads = 1 for single instance (NON-RAC).
    (maximum number of logfiles for each thread + 1) * maximum number of threads
    Message was edited by:
    Reega

  • Multiple Public IP's on one physical interface for devices behind Router.

    Hi guys, I am trying to find information on applying multiple IP addresses to a router
    basically one for the Router itself and then some for the devices behind the router, Which i am sure I need to apply some 1 to 1 NATs. I just do not know if i need to specify all the IP addresses on the main interface.
    Example being I have a router with WAN ip of xxx.xxx.xxx.xxx/25 , it only has 2 interface one for WAN one for LAN, i have a server I would like assigned its own public IP address.  but still on the same LAN network.
    Could someone help me out and point me in the right direction with a sample config

    I agree with the previous response that you need a static NAT to allow outside resources to initiate traffic to your server. You also will need NAT or PAT using the router interface address to allow the other hosts in your network to access outside.
    You do not need to configure any other of the addresses on the router interface other than the primary IP that you assign to the router interface. As long as the other addresses are used for NAT/PAT they are configured in the nat statements and not on the physical interface.
    HTH
    Rick

  • One instance of FCKeditor for multiple fields in a page

    How to implement only one instance of FCKeditor (one set of buttons) for multiple textareas in a page?

    Hello,
    Is that possible with the normal FCK Editor?
    I've never seen something like that on any website, but if you find such an example, I can have a look how it's done. If you see it somewhere working, we should be able to make it work in APEX as well.
    Regards,
    Dimitri
    -- http://dgielis.blogspot.com/
    -- http://www.apex-evangelists.com/
    -- http://www.apexblogs.info/

  • How to open multiple sql files in only one ssms instance

    how to open multiple sql files in only one ssms instance, I can't get anything to work that I find online..I hope you can help us.

    I tried opening two files but selecting and hitting enter. it opens one SSMS and two tabs.
    Balmukund Lakhani
    Please mark solved if I've answered your question, vote for it as helpful to help other users find a solution quicker
    This posting is provided "AS IS" with no warranties, and confers no rights.
    My Blog |
    Team Blog | @Twitter
    | Facebook
    Author: SQL Server 2012 AlwaysOn -
    Paperback, Kindle

  • Multiple Databases One Instance

    Hello,
    Is it possible to have multiple MaxDB databases installed within one MaxDB instance?  Everything I've read about MCOD leads me to avoid this if possible; however, budget limitations leave our hardware lacking the ability to host multiple DB instances.
    It will be a NetWeaver WebAS ABAP and a NetWeaver WebAS J2EE instance being installed (ECC and EP).  I've worked with MCOD systems before, and system copies were cumbersome.  More or less I did a DB specific migration for the ABAP, and then did a R3Load for the J2EE.  If that is the only option, then that is the only option.  I would just like to be able to document this ahead of time.
    Thank you,
    Zach

    Mark,
    Thank you for the reply.  I'm going through this presentation; however, it looks very familiar.  MCOD does allow
    for different SAP components to be independently installed into 1 MaxDB instance, but is it possible to do system
    refreshes of these servers easily?  If I remember correctly, I was able to use the SAP provided tools for the first
    component.  But every other component had to be done independently using R3Load because the SAP Tool
    using database specific copies required initialization (formatting) of the database.
    I've been reading a current post in this forum regarding features of MaxDB 7.8.  I suppose the question is now:
    what is the lesser evil?  MCOD (NetWeaver WebAS ABAP & NetWeaver WebAS J2EE) or each component in
    its own MaxDB instance on the same host.
    Thanks,
    Zach

  • Copying an entire software instrument track from one project to another

    Hello,
    Is it possible to copy or import one entire software instrument track from one GB 3.0.2 project to another? At the moment I've got to copy a region from one project, open another project, paste it in the 2nd project, and open the other one again (which appears to close the 2nd project) to copy the second region. This is incredibly cumbersome because I can't have both projects open at the same time.
    Has anyone found a less tiresome method to do this?
    Thanks
    Hiranya
    Powerbook 15" Hi Res 1.67 GHz 2 Gb RAM   Mac OS X (10.4.6)  

    The easiest work-around I can imagine is to join all regions of the track and copy that. Another option is to freeze the track, which will turn it into normal audio. You might also add your MIDI parts to the library. That will avoid the need to switch between projects, but does require one or two more actions.

Maybe you are looking for